Position Sensors/EVWAE/D 10 mm GS Sensors Type: EVWAE/EVWAD Low profile, long life sensor, which is suitable for detecting the angles of rotating axes. ■ Features ● Low profile (H=2.2 mm), Shaft hole diameters of up to 4 mm are available. ● Long operation life: 1 million operation cycles. ● A wide electrical output angle of a maximum 343 °, ready for SMDs ■ Recommended Applications ● Detection of robot joint angles ● Detection of air conditioner damper angles ● Detection of various control unit angles ■ Explanation of Part Numbers 1 2 E 3 V W 4 5 A E D Product Code 6 7 8 9 10 11 12 B Specification Taper & Resistance Shaft Type 7th, 8th, 9th 001 D hole Type 002 H hole Type ■ Specifications Rating 0.05 W, 5V Mechanical Operating Force 3 mN·m max. Total Resistance 5 k액±30 %, 10 k액±30 % Electrical Linearity Endurance ±2 % max. Operating Life 1000000 cycles min. (operation Angle ±30 °) Minimum Quantity/Packing Unit 1500 pcs. Embossed Taping (Reel Pack) Quantity/Carton 6000 pcs. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. – EV30 – 00 Oct. 2012 Position Sensors/EVWAE/D ■ Dimensions in mm (not to scale) No. 1 EVAWAE EVAWAD +0 0 .05 Mounting surface 0.8 +0.05 0 1.1 .1 φ1 3 #2’ #3 #2 #1 5 3-1 2.5 2.5 #1 #2 #3 0.1 O C 6) (φ 9.0 m .2 .3 φ1 7.2 . 8.7 ax 7.35 0 φ5 –0.1 5.3 .1 6.7 O C Sleeve #2’ #2’ 5.2 0.2 2.6 7.0 With sleeve Type 0.2 Marking #1 #2 #3 1.2 3-1.4 8.4 2.2 2.5 10.6 2.5 9.4±0.05 Circuit diagram PWB mounting hole for reference (Pitch tolerance : ±0.1) 0 2-φ1–0.1 9.4 Shaft Type D Type 2.8 View from mounting side H Type .1 +0 0 .1 +0 0 +0.1 0 φ4 3 3 +0.1 0 φ4 2.97±0.05 5 2-R0.1 : 0.5 Length Shaft Type 7th, 8th, 9th D Type 001 H Type 002 No. 2 EVAWAE EVAWAD Without sleeve Type +0 0 .05 Mounting surface #1 #2 #3 7.0 φ1 5.2 .3 φ1 #2’ #3 #2 #1 9.0 +0.05 0 3 1.1 6.7 5.3 7.35 8.7 .1 #2’ #2’ 0.2 7.2 2.6 0.1 3-1 2.5 2.5 0.2 Marking #1 #2 #3 1.2 3-1.4 8.4 2.2 2.5 10.6 2.5 8±0.05 Circuit diagram PWB mounting hole for reference (Pitch tolerance : ±0.1) 0 2-φ1–0.1 Shaft Type D Type 8.0 H Type .1 +0 0 .1 +0 0 φ4 5 2-R0.1 : 0.5 Length 2.97±0.05 3 3 +0.1 0 φ4 +0.1 0 2.8 View from mounting side Shaft Type 7th, 8th, 9th D Type 001 H Type 002 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. – EV31 – 00 Oct. 2012