ISL12008 I2C Real Time Clock with Battery Backup ® Data Sheet September 26, 2008 FN6690.1 Low Power RTC with Battery ReSeal™ Function Features The ISL12008 device is a low power real time clock/calendar that is pin compatible and functionally equivalent to the ST M41T00S and Maxim DS1340 with timing and crystal compensation. The device additionally provides power-fail indicator, software alarm and intelligent battery backup. • Functionality Equivalent to ST M41T00S and Maxim DS1340 The oscillator uses an external, low-cost 32.768kHz crystal. The real time clock tracks time with separate registers for hours, minutes, and seconds. The device has calendar registers for date, month, year and day of the week. The calendar is accurate through 2099, with automatic leap year correction. Pinout • Pin Compatible to ST M41T00S and Maxim DS1340 • Real Time Clock/Calendar - Tracks Time in Hours, Minutes, Seconds and Sub-seconds - Day of the Week, Day, Month, and Year • 512Hz Frequency Outputs for On-Chip Crystal Compensation • Software Alarm - Settable to the Second, Minute, Hour, Day of the Week, Day, or Month • Automatic Low-Drop Battery Switch for Longest Backup Life ISL12008 (8 LD SOIC) TOP VIEW • Power Failure Detection X1 1 8 VDD • Battery ReSeal™ for Long Shelf Life • I2C Bus™ - 400kHz Data Transfer Rate X2 2 7 FT/OUT VBAT 3 6 SCL GND 4 5 SDA • 800nA Battery Supply Current • Small Package Option - 8 Ld SOIC Ordering Information PART NUMBER (Note) ISL12008IB8Z VDD PART RANGE MARKING (V) TEMP. RANGE PACKAGE PKG. (°C) (Pb-free) DWG. # 12008 IBZ 2.7 to 5.5 -40 to +85 8 Ld SOIC M8.15 • Pb-Free (RoHS Compliant) Applications ISL12008IB8Z-T* 12008 IBZ 2.7 to 5.5 -40 to +85 8 Ld SOIC M8.15 • Utility Meters *Please refer to TB347 for details on reel specifications. • HVAC Equipment NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. • Audio/Video Components • Set-Top Box/Television • Modems • Network Routers, Hubs, Switches, Bridges • Cellular Infrastructure Equipment • Fixed Broadband Wireless Equipment • Pagers/PDA • POS Equipment • Test Meters/Fixtures • Office Automation (Copiers, Fax) • Home Appliances • Computer Products • Other Industrial/Medical/Automotive . 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. ReSeal™ is a trademark owned byIntersil Americas Inc.Copyright Intersil Americas Inc. 2008. All Rights Reserved I2C Bus™ is a trademark owned by NXP Semiconductors Netherlands, B.V. All other trademarks mentioned are the property of their respective owners. ISL12008 Block Diagram SDA SDA BUFFER SCL SCL BUFFER I2C INTERFACE SECONDS RTC CONTROL LOGIC MINUTES HOURS DAY OF WEEK X1 CRYSTAL OSCILLATOR X2 RTC DIVIDER DATE MONTH VDD POR YEAR FREQUENCY OUT CONTROL REGISTERS VTRIP SWITCH FT/OUT INTERNAL SUPPLY VBAT Pin Descriptions PIN NUMBER SYMBOL DESCRIPTION 1 X1 The X1 pin is the input of an inverting amplifier and is intended to be connected to one pin of an external 32.768kHz quartz crystal. X1 can also be driven directly from a 32.768kHz source. 2 X2 The X2 pin is the output of an inverting amplifier and is intended to be connected to one pin of an external 32.768kHz quartz crystal. 3 VBAT This input provides a backup supply voltage to the device. VBAT supplies power to the device in the event that the VDD supply fails. This pin should be tied to ground if not used. 4 GND Ground 5 SDA Serial Data (SDA) is a bidirectional pin used to transfer serial data into and out of the device. It has an open drain output and may be wire OR’ed with other open drain or open collector outputs. 6 SCL The Serial Clock (SCL) input is used to clock all serial data into and out of the device. 7 FT/OUT 8 VDD 512Hz Frequency Output or digital output pin. The function is set via the configuration register. This pin is open drain and requires an external pull-up resistor. Power supply 2 FN6690.1 September 26, 2008 ISL12008 Absolute Maximum Ratings Thermal Information Voltage on VDD, VBAT, SCL, SDA, and FT/OUT Pins (Respect to GND). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 6.5V Voltage on X1 and X2 Pins (Respect to GND) VDD Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VDD + 0.5 VBAT Mode . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VBAT + 0.5 Thermal Resistance (Typical, Note 1) θJA (°C/W) 8 Lead SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTE: 1. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. DC Operating Characteristics – RTC Temperature = -40°C to +85°C. Recommended Operating Conditions, unless otherwise specified. SYMBOL PARAMETER VDD Main Power Supply VBAT Battery Supply Voltage IDD1 Supply Current IDD2 Supply Current With I2C Active IDD3 IBAT CONDITIONS MIN (Note 8) TYP (Note 5) MAX (Note 8) UNITS 5.5 V 2.7 1.8 5.5 V VDD = 5V 2.8 6 µA VDD = 3V 1.6 4 µA VDD = 5V 40 120 µA 2, 3 Supply Current (Low Power Mode) VDD = 5V, LPMODE = 1 2.3 5 µA 2 Battery Supply Current VBAT = 3V, +25°C 800 950 nA 2 ILI Input Leakage Current on SCL -1 0.1 +1 µA ILO I/O Leakage Current on SDA -1 0.1 +1 µA VBAT Mode Threshold 2.3 2.6 2.9 VTRIP NOTES 2, 3 V VTRIPHYS VTRIP Hysteresis 36 mV 6 VBATHYS VBAT Hysteresis 53 mV 6 FT/OUT VOL Output Low Voltage Power-Down Timing 0.02 0.4 V VDD = 2.7V IOL = 1mA 0.02 0.4 V Temperature = -40°C to +85°C. Recommended Operating Conditions unless otherwise specified. SYMBOL VDD SR- VDD = 5V IOL = 3mA PARAMETER CONDITIONS MIN (Note 8) TYP (Note 5) MAX (Note 8) UNITS NOTES 5 V/ms 4 VDD Negative Slewrate Serial Interface Specifications Recommended Operating Conditions. Unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS MIN (Note 8) TYP (Note 5) MAX (Note 8) UNITS NOTES SERIAL INTERFACE SPECS VIL SDA and SCL Input Buffer LOW Voltage -0.3 0.3 x VDD V VIH SDA and SCL Input Buffer HIGH Voltage 0.7 x VDD VDD + 0.3 V Hysteresis SDA and SCL Input Buffer Hysteresis VOL SDA Output Buffer LOW Voltage, Sinking 3mA Cpin SDA and SCL Pin Capacitance 3 V 0.05 x VDD 0 TA = +25°C, f = 1MHz, VDD = 5V, VIN = 0V, VOUT = 0V 0.02 0.4 V 10 pF 6, 7 6, 7 FN6690.1 September 26, 2008 ISL12008 Serial Interface Specifications Recommended Operating Conditions. Unless otherwise specified. (Continued) SYMBOL fSCL PARAMETER TEST CONDITIONS MIN (Note 8) SCL Frequency TYP (Note 5) MAX (Note 8) UNITS NOTES 400 kHz tIN Pulse width Suppression Time at SDA and SCL Inputs Any pulse narrower than the max spec is suppressed. 50 ns tAA SCL Falling Edge to SDA Output Data Valid SCL falling edge crossing 30% of VDD, until SDA exits the 30% to 70% of VDD window. 900 ns tBUF Time the Bus Must be Free Before the Start of a New Transmission SDA crossing 70% of VDD during a STOP condition, to SDA crossing 70% of VDD during the following START condition. 1300 ns tLOW Clock LOW Time Measured at the 30% of VDD crossing. 1300 ns tHIGH Clock HIGH Time Measured at the 70% of VDD crossing. 600 ns tSU:STA START Condition Setup Time SCL rising edge to SDA falling edge. Both crossing 70% of VDD. 600 ns tHD:STA START Condition Hold Time From SDA falling edge crossing 30% of VDD to SCL falling edge crossing 70% of VDD. 600 ns tSU:DAT Input Data Setup Time From SDA exiting the 30% to 70% of VDD window, to SCL rising edge crossing 30% of VDD. 100 ns tHD:DAT Input Data Hold Time From SCL falling edge crossing 30% of VDD to SDA entering the 30% to 70% of VDD window. 20 tSU:STO STOP Condition Setup Time From SCL rising edge crossing 70% of VDD, to SDA rising edge crossing 30% of VDD. 600 ns tHD:STO STOP Condition Hold Time From SDA rising edge to SCL falling edge. Both crossing 70% of VDD. 600 ns Output Data Hold Time From SCL falling edge crossing 30% of VDD, until SDA enters the 30% to 70% of VDD window. 0 ns tR SDA and SCL Rise Time From 30% to 70% of VDD 20 + 0.1 x Cb 300 ns 6, 7 tF SDA and SCL Fall Time From 70% to 30% of VDD 20 + 0.1 x Cb 300 ns 6, 7 Cb Capacitive Loading of SDA or SCL Total on-chip and off-chip 10 400 pF 6, 7 Rpu SDA and SCL Bus Pull-Up Resistor Off-Chip Maximum is determined by tR and tF. For Cb = 400pF, max is about 2kΩ to~2.5kΩ. For Cb = 40pF, max is about 15kΩ to ~20kΩ. kΩ 6, 7 tDH 900 ns 1 NOTES: 2. FT/OUT inactive. 3. LPMODE = 0 (default). 4. In order to ensure proper timekeeping, the VDD SR- specification must be followed. 5. Typical values are for T = +25°C and 3.3V supply voltage. 6. Limits should be considered typical and are not production tested. 7. These are I2C specific parameters and are not tested, however, they are used to set conditions for testing devices to validate specification. 8. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 4 FN6690.1 September 26, 2008 ISL12008 SDA vs SCL Timing tHIGH tF SCL tLOW tR tSU:DAT tSU:STA tHD:DAT tSU:STO tHD:STA SDA (INPUT TIMING) tAA tDH tBUF SDA (OUTPUT TIMING) Symbol Table WAVEFORM INPUTS OUTPUTS Must be steady Will be steady May change from LOW to HIGH Will change from LOW to HIGH May change from HIGH to LOW Will change from HIGH to LOW Don’t Care: Changes Allowed Changing: State Not Known N/A Center Line is High Impedance 5 FN6690.1 September 26, 2008 ISL12008 Temperature is +25°C, unless otherwise specified. 0.2 1.00 1.8 0.95 1.6 0.90 1.4 0.85 1.2 0.80 IBAT (µA) IBAT (µA) Typical Performance Curves 1.0 0.8 0.75 0.70 0.6 0.65 0.4 0.60 0.2 0.55 0 1.8 2.3 2.8 3.3 3.8 VBAT (V) 4.3 4.8 0.50 -40 5.3 FIGURE 1. IBAT vs VBAT -20 0 20 40 TEMPERATURE (°C) 60 80 FIGURE 2. IBAT vs TEMPERATURE AT VBAT = 3V 3.5 3.5 VDD = 5V 3.0 3.0 ICC (µA) IDD (µA) 2.5 2.5 2.0 LP MODE OFF 2.0 1.5 LP MODE ON VDD = 3.3V 1.5 1.0 1.0 -40 -20 0 20 40 TEMPERATURE (°C) 60 80 0.5 1.8 2.3 2.8 3.3 3.8 VDD (V) 4.3 4.8 5.3 FIGURE 3. IDD1 vs TEMPERATURE FIGURE 4. IDD1 vs VDD WITH LPMODE ON AND OFF EQUIVALENT AC OUTPUT LOAD CIRCUIT FOR VDD = 5V The calendar is accurate through 2099, with automatic leap year correction. 5.0V 1533Ω FOR VOL= 0.4V AND IOL = 3mA SDA AND FT/OUT 100pF FIGURE 5. STANDARD OUTPUT LOAD FOR TESTING THE DEVICE WITH VDD = 5.0V General Description The ISL12008 device is a low power real time clock with timing and crystal compensation, clock/calendar, power fail indicator, software alarm, and intelligent battery backup switching. The oscillator uses an external, low-cost 32.768kHz crystal. The real time clock tracks time with separate registers for hours, minutes, seconds, and sub-seconds. The device has calendar registers for date, month, year and day of the week. 6 The ISL12008's powerful alarm can be set to any clock/calendar value for a match. For example, every minute, every Tuesday or at 5:23 AM on March 21. The alarm status is available by checking the Status Register. The device also offers a backup power input pin. This VBAT pin allows the device to be backed up by battery or super capacitor with automatic switchover from VDD to VBAT. The entire ISL12008 device is fully operational from 2.7V to 5.5V and the clock/calendar portion of the device remains fully operational down to 1.8V in battery mode. Pin Descriptions X1, X2 The X1 and X2 pins are the input and output, respectively, of an inverting amplifier. An external 32.768kHz quartz crystal is used with the ISL12008 to supply a timebase for the real time clock. Internal compensation circuitry provides high accuracy over the operating temperature range from -40°C to +85°C. This oscillator compensation network can be used to calibrate FN6690.1 September 26, 2008 ISL12008 the crystal timing accuracy over-temperature either during manufacturing or with an external temperature sensor and microcontroller for active compensation (see Figure 6). X1 X2 FIGURE 6. RECOMMENDED CRYSTAL CONNECTION VBAT This input provides a backup supply voltage to the device. VBAT supplies power to the device in the event that the VDD supply fails. This pin can be connected to a battery, a super capacitor or tied to ground if not used. FT/OUT (512Hz Frequency Output/Logic Output) This dual function pin can be used as a 512Hz frequency output pin for on-chip crystal compensation or a simple digital output control via I2C. The FT/OUT mode is selected via the OUT and FT control bits of the control/status register (address 07h). This pin is an open drain output requires the use of a pull-up resistor. Serial Clock (SCL) The SCL input is used to clock all serial data into and out of the device. The input buffer on this pin is always active (not gated). It is disabled when the backup power supply on the VBAT pin is activated to minimize power consumption. Serial Data (SDA) up to a month. See “Application Section” on page 16 for more information. Normal Mode (VDD) to Battery Backup Mode (VBAT) To transition from the VDD to VBAT mode, both of the following conditions must be met: Condition 1: VDD < VBAT - VBATHYS where VBATHYS ≈ 50mV Condition 2: VDD < VTRIP where VTRIP ≈ 2.6V Battery Backup Mode (VBAT) to Normal Mode (VDD) The ISL12008 device will switch from the VBAT to VDD mode when one of the following conditions occurs: Condition 1: VDD > VBAT + VBATHYS where VBATHYS ≈ 50mV Condition 2: VDD > VTRIP + VTRIPHYS where VTRIPHYS ≈ 30mV These power control situations are illustrated in Figures 7 and 8. BATTERY BACKUP MODE VDD SDA is a bidirectional pin used to transfer data into and out of the device. It has an open drain output and may be ORed with other open drain or open collector outputs. The input buffer is always active (not gated) in normal mode. VTRIP 2.6V VBAT 1.8V VBAT + VBATHYS VBAT - VBATHYS An open drain output requires the use of a pull-up resistor. The output circuitry controls the fall time of the output signal with the use of a slope controlled pull-down. The circuit is designed for 400kHz I2C bus speeds. It is disabled when the backup power supply on the VBAT pin is activated. FIGURE 7. BATTERY SWITCHOVER WHEN VBAT < VTRIP VDD, GND Chip power supply and ground pins. The device will operate with a power supply from 2.7V to 5.5VDC. A 0.1µF decoupling capacitor is recommended on the VDD pin to ground. Functional Description BATTERY BACKUP MODE VDD VBAT 3.0V VTRIP 2.6V VTRIP VTRIP + VTRIPHYS Power Control Operation The power control circuit accepts a VDD and a VBAT input. Many types of batteries can be used with Intersil RTC products. For example, 3.0V or 3.6V Lithium batteries are appropriate, and battery sizes are available that can power the ISL12008 for up to 10 years. Another option is to use a super capacitor for applications where VDD is interrupted for 7 FIGURE 8. BATTERY SWITCHOVER WHEN VBAT > VTRIP FN6690.1 September 26, 2008 ISL12008 The I2C bus is deactivated in battery backup mode to provide lower power. Aside from this, all RTC functions are operational during battery backup mode. Except for SCL and SDA, all the inputs and outputs of the ISL12008 are active during battery backup mode unless disabled via the control register. Power Failure Detection The ISL12008 provides a Real Time Clock Failure Bit (RTCF, address 0Bh) to detect total power failure. It allows users to determine if the device has powered up after having lost all power to the device (both VDD and VBAT). Low Power Mode The normal power switching of the ISL12008 is designed to switch into battery backup mode only if the VDD power is lost. This will ensure that the device can accept a wide range of backup voltages from many types of sources while reliably switching into backup mode. Another mode, called Low Power Mode, is available to allow direct switching from VDD to VBAT without requiring VDD to drop below VTRIP. Since the additional monitoring of VDD vs VTRIP is no longer needed, that circuitry is shut down and less power is used while operating from VDD. Power savings are typically 600nA at VDD = 5V. Low Power Mode is activated via the LPMODE bit (address 08h, bit 5) in the control and status registers. Real Time Clock Operation The Real Time Clock (RTC) uses an external 32.768kHz quartz crystal to maintain an accurate internal representation of sub-second, second, minute, hour, day of week, date, month, and year. The RTC has leap-year correction, and corrects for months having fewer than 31 days. The RTC hours is in 24-hour format only. When the ISL12008 powers up after the loss of both VDD and VBAT, the RTC will not begin incrementing until at least one byte is written to the RTC registers. The sub-second register will increment after power up but it will not casue the other RTC registers to incremnent until at least one byte is written to the RTC registers. Accuracy of the Real Time Clock The accuracy of the Real Time Clock depends on the frequency of the quartz crystal that is used as the time base for the RTC. Since the resonant frequency of a crystal is temperature dependent, the RTC performance will also be dependent upon temperature. The frequency deviation of the crystal is a function of the turnover temperature of the crystal from the crystal’s nominal frequency. For example, a ~20ppm frequency deviation translates into an accuracy of ~1 minute per month. These parameters are available from the crystal manufacturer. The ISL12008 provides on-chip crystal compensation networks to adjust load capacitance to tune oscillator frequency from -97.0695ppm to +206.139ppm. For more detailed information. See “Application Section” on page 16. Low Power Mode is useful in systems where VDD is normally higher than VBAT at all times. The device will switch from VDD to VBAT when VDD drops below VBAT, with about 50mV of hysteresis to prevent any switchback of VDD after switchover. In a system with a VDD = 5V and backup lithium battery of VBAT = 3V, Low Power Mode can be used. However, it is not recommended to use Low Power Mode in a system with VDD = 3.3V ±10%, VBAT ≥ 3.0V, and when there is a finite I-R voltage drop in the VDD line. The ISL12008 has an I2C serial bus interface that provides access to the control and status registers and the user SRAM. The I2C serial interface is compatible with other industry I2C serial bus protocols using a bidirectional data signal (SDA) and a clock signal (SCL). InterSeal™ and ReSeal™ Battery Saver Oscillator Compensation The ISL12008 has the InterSeal Battery Saver, which prevents initial battery current drain before it is first used. For example, battery-backed RTCs are commonly packaged on a board with a battery connected. In order to preserve battery life, the ISL12008 will not draw any power from the battery source until after the device is first powered up from the VDD source. Thereafter, the device will switchover to battery backup mode whenever VDD power is lost. The ISL12008 provides the option of timing correction due to temperature variation of the crystal oscillator for either manufacturing calibration or active calibration. The total possible compensation is typically -97.0695ppm to +206.139ppm. Two compensation mechanisms that are available are as follows: The ISL12008 has the ReSeal function, which allows the device to enter into the InterSeal Battery Saver mode after manufacture testing for board functionality. To use the ReSeal function, simply set RESEAL bit to “1” (address 0Bh) after the testing is completed. It will enable the InterSeal Battery Saver mode and prevents battery current drain before it is first used. 8 I2C Serial Interface 1. An analog trimming (ATR) register that can be used to adjust individual on-chip digital capacitors for oscillator capacitance trimming. The individual digital capacitor is selectable from a range of 4.5pF to 20.25pF (based upon 32.758kHz). This translates to a calculated compensation of approximately -34ppm to +80ppm (see ATR description on page 16). 2. A digital trimming register (DTR) that can be used to adjust the timing counter by -63.0696ppm to +126.139ppm (see DTR description on page 16). FN6690.1 September 26, 2008 ISL12008 Also provided is the ability to adjust the crystal capacitance when the ISL12008 switches from VDD to battery backup mode. See “Battery Backup Mode (VBAT) to Normal Mode (VDD)” on page 7. Register Descriptions The battery-backed registers are accessible following a slave byte of “1101000x” and reads or writes to addresses [00h:1Fh]. The defined addresses and default values are described in Table 1. Address 12h to 1Eh are not used. Reads or writes to 12h to 1Eh will not affect operation of the device but should be avoided. REGISTER ACCESS The contents of address 00h to 07h can be modified by performing a byte or a page write operation directly to any register address. In a page write operation to address 00h to 07h, the address will wrap around from 07h to 00h. All the other registers (Address 08h to 11h and 1Fh) can be modified by performing a byte write operation. The registers are divided into 3 sections. These are: 1. Real Time Clock (8 bytes): Address 00h to 06h, and 1Fh. Address 1Fh is Sub-Second register and it is a read-only. 2. Control and Status (4 bytes): Address 07h to 0Bh. 3. Alarm (6 bytes): Address 0Ch to 11h. There are no addresses above 1Fh. Address 12h to 1Eh are not used. Reads or writes to 12h to 1Eh will not affect operation of the device but should be avoided. A register can be read by performing a random read at any address at any time. This returns the contents of that register location. Additional registers are read by performing a sequential read. For the RTC and Alarm registers, the read operation latches all clock registers into a buffer, so an update of the clock does not change the time being read. A sequential read will not result in the output of data from the memory array. At the end of a read, the master supplies a stop condition to end the operation and free the bus. After a read, the address remains at the previous address +1 so the user can execute a current address read and continue reading the next register. In a sequential read, the address will warp around at address 07h to 00h; therefore, please use byte read operation to read the registers after address 07h. 9 FN6690.1 September 26, 2008 ISL12008 Real Time Clock Registers TABLE 1. REGISTER MEMORY MAP BIT REG REG NAME 7 6 5 4 3 2 1 0 SC ST SC22 SC21 SC20 SC13 SC12 SC11 SC10 0 to 59 00h 01h MN OF MN22 MN21 MN20 MN13 MN12 MN11 MN10 0 to 59 80h 02h HR CEB CB HR21 HR20 HR13 HR12 HR11 HR10 0 to 23 00h 03h DW 0 0 0 0 0 DW12 DW11 DW10 1 to 7 00h 04h DT 0 0 DT21 DT20 DT13 DT12 DT11 DT10 1 to 31 00h 05h MO 0 0 0 MO20 MO13 MO12 MO11 MO10 1 to 12 00h 06h YR YR23 YR22 YR21 YR20 YR13 YR12 YR11 YR10 0 to 99 00h DTR OUT FT DTR5 DTR4 DTR3 DTR2 DTR1 DTR0 N/A 80h 08h INT 0 ALME LPMODE 0 0 0 0 0 N/A 00h 09h OF OF 0 0 0 0 0 0 0 N/A 80h 0Ah ATR BMATR1 BMATR0 ATR5 ATR4 ATR3 ATR2 ATR1 ATR0 N/A 00h ADDR. SECTION 00h 07h RTC Control RTC RANGE DEFAULT 0Bh Status SR ARST XSTOP RESEAL 0 0 ALM BAT RTCF N/A 03h 0Ch Alarm0 SCA ESCA ASC22 ASC21 ASC20 ASC13 ASC12 ASC11 ASC10 00 to 59 00h 0Dh MNA EMNA AMN22 AMN21 AMN20 AMN13 AMN12 AMN11 AMN10 00 to 59 00h 0Eh HRA EHRA 0 AHR21 AHR20 AHR13 AHR12 AHR11 AHR10 0 to 23 00h 0Fh DTA EDTA 0 ADT21 ADT20 ADT13 ADT12 ADT11 ADT10 1 to 31 00h 10h MOA EMOA 0 0 AMO20 AMO13 AMO12 AMO11 AMO10 1 to 12 00h 11h DWA EDWA 0 0 0 0 ADW12 ADW11 ADW10 1 to 7 00h SS SS23 SS22 SS21 SS20 SS13 SS12 SS11 SS10 0 to 99 00h 1Fh (ReadOnly) RTC NOTE: 0 = must be set to‘0’ Addresses [00h to 06h, and 1Fh] RTC REGISTERS (SC, MN, HR, DW, DT, MO, YR, SS) These registers depict BCD representations of the time. As such, SC (Seconds, address 00h) and MN (Minutes, address 01h) range from 0 to 59, HR (Hour, address 02h) is in 24-hour mode with a range from 0 to 23, DW (Day of the Week, address 03h) is 1 to 7, DT (Date, address 04h) is 1 to 31, MO (Month, address 05h) is 1 to 12, YR (Year, address 06h) is 0 to 99, and SS (Sub-Seconds/Hundredths of Seconds, address 1Fh) is 0 to 99. The default for all the time keeping bits are set to “0” at power up. Bit D7 of SC register contain the crystal enable/disable bit (ST). Setting ST to “1” will disable the crystal from oscillating and stop the counting in RTC register. When the ST bit is set to “1”, it will casue the OF bit to set to “1” due to no crystal oscillation on the X1 pin. The ST bit is set to “0” on power-up for normal operation. oscillation. This bit can be reset when the X1 has crystal oscillation and a write to “0”. This bit can only be written as “0” and not as a “1”. The OF bit is set to “1” at power-up from a complete power down (VDD and VBAT are removed). Address 9, bit 7 is also used as the OF bit for DS1340 compatibility, and the two OF bits are interchangable. Bits D6 and D7 of HR register (century/hours register) contain the century enable bit (CEB) and the century bit (CB). Setting CEB to a '1' will cause CB to toggle, either from '0' to '1' or from '1' to '0' at the turn of the century (depending upon its initial state). If CEB is set to a '0', CB will not toggle. The DW register provides a Day of the Week status and uses three bits DW2 to DW0 to represent the seven days of the week. The counter advances in the cycle 1-2-3-4-5-6-7-1-2… The assignment of a numerical value to a specific day of the week is arbitrary and may be decided by the system software designer. Bit D7 of MN register contain the Oscillator Fail Indicator bit (OF). This bit is set to a “1” when the X1 pin has no 10 FN6690.1 September 26, 2008 ISL12008 LEAP YEARS ReSeal (RESEAL) Leap years add the day February 29 and are defined as those years that are divisible by 4. Years divisible by 100 are not leap years, unless they are also divisible by 400. This means that the year 2000 is a leap year, the year 2100 is not. The ISL12008 does not correct for the leap year in the year 2100. The ReSeal™ enables the device enter into the InterSeal™ Battery Saver mode after manufacture testing for board functionality. The factory default setting of this bit is “0”. The RESEAL must be set to “0” to enable the battery function during normal operation or full functional testing. To use the ReSeal function, simply set RESEAL bit to “1” after the testing is completed. It will enable the InterSeal™ Battery Saver mode and prevents battery current drain before it is first used. Control and Status Registers Addresses [07h to 0Bh] The Control and Status Registers consist of the Status Register, Interrupt and Alarm Register, Analog Trimming and Digital Trimming Registers. Status Register (SR) [Address 0Bh] The Status Register is located in the memory map at address 0Bh. This is a volatile register that provides either control or status of RTC failure, battery mode, alarm trigger, crystal oscillator status, ReSeal™ and auto reset of status bits. AUTO RESET ENABLE BIT (ARST) This bit enables/disables the automatic reset of the BAT, ALM and TMR status bits only. When ARST bit is set to “1”, these status bits are reset to “0” after a valid read of the respective status register (with a valid STOP condition). When the ARST is cleared to “0”, the user must manually reset the BAT and ALM bits. Interrupt Control Register (INT) [Address 08h] TABLE 3. INTERRUPT CONTROL REGISTER (INT) TABLE 2. STATUS REGISTER (SR) ADDR 7 6 5 4 3 0Bh ARST 0 RESEAL 0 0 Default 0 0 0 0 0 2 1 0 ALM BAT RTCF 0 1 1 ADDR 7 08h 0 Default 0 6 5 ALME LPMODE 0 0 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 REAL TIME CLOCK FAIL BIT (RTCF) LOW POWER MODE BIT (LPMODE) This bit is set to a “1” after a total power failure. This is a read only bit that is set by hardware (ISL12008 internally) when the device powers up after having lost all power to the device (both VDD and VBAT go to 0V). The bit is set regardless of whether VDD or VBAT is applied first. The loss of only one of the supplies does not set the RTCF bit to “1”. On power-up after a total power failure, all registers are set to their default states and the clock will not increment until at least one byte is written to the clock register. The first valid write to the RTC section after a complete power failure resets the RTCF bit to “0” (writing one byte is sufficient). This bit enables/disables low power mode. With LPMODE = “0”, the device will be in normal mode and the VBAT supply will be used when VDD < VBAT - VBATHYS and VDD < VTRIP. With LPMODE = “1”, the device will be in low power mode and the VBAT supply will be used when VDD < VBAT - VBATHYS. There is a supply current saving of about 600nA when using LPMODE = “1” with VDD = 5V. (See “Typical Performance Curves” on page 6: IDD vs VCC with LPMODE ON and OFF.) BATTERY BIT (BAT) This bit is set to a “1” when the device enters battery backup mode. This bit can be reset either manually by the user or automatically reset by enabling the auto-reset bit (see ARST bit). A write to this bit in the SR can only set it to “0”, not “1”. ALARM BIT (ALM) ALARM ENABLE BIT (ALME) This bit enables/disables the alarm function. When the ALME bit is set to “1”, the alarm function is enabled. When the ALME bit is cleared to “0”, the alarm function is disabled. ALME bit is set to “0” at power-up. Oscillator Fail Register (OF) [Address 09h] TABLE 4. INTERRUPT CONTROL REGISTER (INT) ADDR These bits announce if the alarm matches the real time clock. If there is a match, the respective bit is set to “1”. This bit can be manually reset to “0” by the user or automatically reset by enabling the auto-reset bit (see ARST bit). A write to this bit in the SR can only set it to “0”, not “1”. NOTE: An alarm bit that is set by an alarm occurring during an SR read operation will remain set after the read operation is complete. 11 09h Default 7 6 5 4 3 2 1 0 OF 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 OSCILLATOR FAIL BIT (OF) This bit is set to a “1” when the X1 pin has no oscillation. This bit can be reset when the X1 has crystal oscillation and a write to “0”. This bit can only be written as “0” and not as a “1”. The OF bit is set to “1” at power up from a complete power down (VDD and VBAT are removed). Address 1, bit 7 FN6690.1 September 26, 2008 ISL12008 is also used as the OF bit for M41T00S compatibility, and the two OF bits are interchangable. of load capacitance goes from 4.5pF to 20.25pF in 0.25pF steps. Note that these are typical values. Analog Trimming Register (ATR) [Address 0Ah] BATTERY MODE ATR SELECTION (BMATR <1:0>) TABLE 5. ANALOG TRIMMING REGISTER (ATR) ADDR 0Ah 7 6 5 4 3 2 1 0 BMATR1 BMATR0 ATR5 ATR4 ATR3 ATR2 ATR1 ATR0 Default 0 0 0 0 0 0 0 Since the accuracy of the crystal oscillator is dependent on the VDD/VBAT operation, the ISL12008 provides the capability to adjust the capacitance between VDD and VBAT when the device switches between power sources. 0 DELTA CAPACITANCE (CBAT TO CVDD) ANALOG TRIMMING REGISTER (ATR<5:0>) BMATR1 BMATR0 0 0 0pF 0 1 -0.5pF (≈ +2ppm) 1 0 +0.5pF (≈ -2ppm) 1 1 +1pF (≈ -4ppm) X1 CX1 CRYSTAL OSCILLATOR X2 CX2 Digital Trimming Register (DTR) [Address 07h] TABLE 6. DIGITAL TRIMMING REGISTER (DTR) ADDR FIGURE 9. DIAGRAM OF ATR Six analog trimming bits, ATR0 to ATR5, are provided in order to adjust the on-chip load capacitance value for frequency compensation of the RTC. Each bit has a different weight for capacitance adjustment. For example, using a Citizen CFS-206 crystal with different ATR bit combinations provides an estimated ppm adjustment range from -34ppm to +80ppm to the nominal frequency compensation. The combination of analog and digital trimming can give up to -97.0695ppm to +206.139ppm of total adjustment. The effective on-chip series load capacitance, CLOAD, ranges from 9pF to 40.5pF with a mid-scale value of 12.5pF (default). CLOAD is changed via two digitally controlled capacitors, CX1 and CX2, connected from the X1 and X2 pins to ground (see Figure 9). The value of CX1 and CX2 are given in Equation 1: C X = ( 16 ⋅ b 5 + 8 ⋅ b 4 + 4 ⋅ b3 + 2 ⋅ b2 + 1 ⋅ b1 + 0.5 ⋅ b0 + 9 )pF (EQ. 1) The effective series load capacitance is the combination of CX1 and CX2 in Equation 2: C LOAD 07h Default 7 6 OUT FT 0 0 5 4 3 2 1 0 DTR5 DTR4 DTR3 DTR2 DTR1 DTR0 0 0 0 0 0 0 DIGITAL TRIMMING REGISTER (DTR<5:0>) Six digital trimming bits, DTR0 to DTR5, are provided to adjust the average number of counts per second and average the ppm error to achieve better accuracy. • DTR5 is a sign bit. DTR5 = “0” means frequency compensation is < 0. DTR5 = “1” means frequency compensation is > 0. • DTR<4:0> are scale bits. With DTR5 = “0”, DTR<4:0> gives -2.0345ppm adjustment per step. With DTR5 = “1”, DTR<4:0> gives +4.0690ppm adjustment per step. A range from -63.0696ppm to +126.139ppm can be represented by using these 3 bits. For example, with DTR = 11111, the digital adjustment is (1111b[15d]*4.0690) = +126.139ppm. With DTR = 01111, the digital adjustment is (-(1111b[15d]*2.0345)) = -63.0696ppm. 512HZ FREQUENCY OUTPUT ENABLE BIT (FT) 1 1 1 ⎛ ---------- + -----------⎞ ⎝C ⎠ X1 C X2 = ----------------------------------- (EQ. 2) 16 ⋅ b5 + 8 ⋅ b4 + 4 ⋅ b3 + 2 ⋅ b2 + 1 ⋅ b1 + 0.5 ⋅ b 0 + 9 C LOAD = ⎛ ------------------------------------------------------------------------------------------------------------------------------⎞ pF ⎝ 2 ⎠ where b5 is ATR5 bit, b4 is ATR4 bit, b3 is ATR3 bit, b2 is ATR1 bit, and b0 is ATR0 bit. For example, CLOAD(ATR = 000000b [0d]) = 12.5pF, CLOAD (ATR = 100000b [32d]) = 4.5pF and CLOAD (ATR = 011111b [31d]) = 20.25pF. The entire range for the series combination 12 This bit enables/disables the 512Hz frequency output on the FT/OUT pin. When the FT is set to “1”, the FT/OUT pin outputs the 512Hz frequency, regardless of the Digital Output selection bit (OUT). The 512Hz frequency output is used for crystal compensation with ATR and DTR registers. When the FT is set to “0”, the 512Hz frequency is disabled and the function of FT/OUT pin is selected by the Digital Output selection bit (OUT). The FT bit is set to “0” on power-up. The FT/OUT pin is an open drain output requires the use of a pull-up resistor. FN6690.1 September 26, 2008 ISL12008 DIGITAL OUTPUT SELECTION BIT (OUT) This bit selects the output status of the FT/OUT. 512Hz Frequency Output Enable bit (FT) must be set to “0” (disable) for OUT to take effect on FT/OUT pin. When the OUT is set to “1” and FT is set to “0”, the FT/OUT pin is set to logic level high. The FT/OUT pin voltage level is controlled by the voltage of the pull-up resistor on FT/OUT pin. When the OUT is set to “0” and FT is set to “0”, the FT/OUT pin is set to logic level low. The voltage level of FT/OUT is set to VOL level. The OUT bit is set to “1” on power-up. The FT/OUT pin is an open drain output requires the use of a pull-up resistor. Alarm Registers Addresses [0Ch to 11h] The Alarm register bytes are set up identical to the RTC register bytes, except that the MSB of each byte functions as an enable bit (enable = “1”). These enable bits specify which alarm registers (seconds, minutes, etc.) are used to make the comparison. Note that there is no alarm byte for year and sub-second, and the register order for Alarm register is not a 100% matching to the RTC register so please take caution on programming the alarm function. The alarm function works as a comparison between the alarm registers and the RTC registers. As the RTC advances, the alarm will be triggered once a match occurs between the alarm registers and the RTC registers. Any one alarm register, multiple registers, or all registers can be enabled for a match. To clear an alarm, the ALM status bit must be set to “0” with a write. Note that if the ARST bit is set to “1” (address 0Bh, bit 7), the ALM bit will automatically be cleared when the status register is read. I2C Serial Interface The ISL12008 supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter and the receiving device as the receiver. The device controlling the transfer is the master and the device being controlled is the slave. The master always initiates data transfers and provides the clock for both transmit and receive operations. Therefore, the ISL12008 operates as a slave device in all applications. All communication over the I2C bus is conducted by sending the MSB of each byte of data first. Protocol Conventions Data states on the SDA line can change only during SCL LOW periods. SDA state changes during SCL HIGH are reserved for indicating START and STOP conditions (see Figure 10). On power-up of the ISL12008, the SDA pin is in the input mode. All I2C bus operations must begin with a START condition, which is a HIGH to LOW transition of SDA while SCL is HIGH. The ISL12008 continuously monitors the SDA and SCL lines for the START condition and does not respond to any command until this condition is met (see Figure 10). A START condition is ignored during the power-up sequence. All I2C bus operations must be terminated by a STOP condition, which is a LOW to HIGH transition of SDA while SCL is HIGH (see Figure 10). A STOP condition at the end of a read operation or at the end of a write operation to memory only places the device in its standby mode. An acknowledge (ACK) is a software convention used to indicate a successful data transfer. The transmitting device, either master or slave, releases the SDA bus after transmitting 8 bits. During the ninth clock cycle, the receiver pulls the SDA line LOW to acknowledge the reception of the 8 bits of data (see Figure 11). The ISL12008 responds with an ACK after recognition of a START condition followed by a valid Identification Byte, and once again after successful receipt of an Address Byte. The ISL12008 also responds with an ACK after receiving a Data Byte of a write operation. The master must respond with an ACK after receiving a Data Byte of a read operation. SCL SDA START DATA STABLE DATA CHANGE DATA STABLE STOP FIGURE 10. VALID DATA CHANGES, START, AND STOP CONDITIONS 13 FN6690.1 September 26, 2008 ISL12008 SCL FROM MASTER 1 8 9 SDA OUTPUT FROM TRANSMITTER HIGH IMPEDANCE HIGH IMPEDANCE SDA OUTPUT FROM RECEIVER START ACK FIGURE 11. ACKNOWLEDGE RESPONSE FROM RECEIVER WRITE SIGNALS FROM THE MASTER SIGNAL AT SDA SIGNALS FROM THE ISL12008 S T A R T ADDRESS BYTE IDENTIFICATION BYTE S T O P DATA BYTE 1 1 0 1 0 0 0 0 A C K A C K A C K FIGURE 12. BYTE WRITE SEQUENCE 14 FN6690.1 September 26, 2008 ISL12008 Device Addressing Write Operation Following a start condition, the master must output a Slave Address Byte. The 7 MSBs are the device identifiers. These bits are “1101000”. A Write operation requires a START condition, followed by a valid Identification Byte, a valid Address Byte, a Data Byte, and a STOP condition. After each of the three bytes, the ISL12008 responds with an ACK. After received the STOP condition, the ISL12008 writes the data into the memory, then the I2C bus enters a standby state. After a Write operation, the internal address pointer will remain at the address for the last data byte written. The last bit of the Slave Address Byte defines a read or write operation to be performed. When this R/W bit is a “1”, then a read operation is selected (refer to Figure 16). When this R/W bit is a “0” , then a write operation (refer to Figure 12). After loading the entire Slave Address Byte from the SDA bus, the ISL12008 compares the Slave bit and device select bits with “1101000”. Upon a correct compare, the device outputs an acknowledge on the SDA line. Following the Slave Byte is a one byte word address. The word address is either supplied by the master device or obtained from an internal counter. On power-up, the internal address counter is set to address 0h, so a current address read of the CCR array starts at address 0h. When required, as part of a random read, the master must supply the 1 Word Address Bytes, as shown in Figure 14. In a random read operation, the slave byte in the “dummy write” portion must match the slave byte in the “read” section. For a random read of the Clock/Control Registers, the slave byte must be “1101000x” in both places. R/W SLAVE ADDRESS BYTE A1 A0 WORD ADDRESS D1 D0 DATA BYTE 1 1 0 1 0 0 0 A7 A6 A5 A4 A3 A2 D7 D6 D5 D4 D3 D2 Read Operation A Read operation consists of a three byte instruction followed by one or more Data Bytes (see Figure 14). The master initiates the operation issuing the following sequence: a START, the Identification byte with the R/W bit set to “0”, an Address Byte, a second START, and a second Identification byte with the R/W bit set to “1”. After each of the three bytes, the ISL12008 responds with an ACK. Then the ISL12008 transmits Data Bytes as long as the master responds with an ACK during the SCL cycle following the eighth bit of each byte. The master terminates the read operation (issuing a STOP condition) following the last bit of the last Data Byte (see Figure 14). The Data Bytes are from the memory location indicated by an internal address pointer. This internal address pointer initial value is determined by the Address Byte in the Read operation instruction, and increments by one during transmission of each Data Byte. FIGURE 13. SLAVE ADDRESS, WORD ADDRESS, AND DATA BYTES SIGNALS FROM THE MASTER S T A R T SIGNAL AT SDA IDENTIFICATION BYTE WITH R/W = 0 S T IDENTIFICATION A BYTE WITH R R/W = 1 T ADDRESS BYTE S T O P A C K 1 1 0 1 0 0 0 1 1 1 0 1 0 0 0 0 A C K SIGNALS FROM THE SLAVE A C K A C K A C K FIRST READ DATA BYTE LAST READ DATA BYTE FIGURE 14. READ SEQUENCE 15 FN6690.1 September 26, 2008 ISL12008 Oscillator Crystal Requirements The ISL12008 uses a standard 32.768kHz crystal. Either through hole or surface mount crystals can be used. Table 7 lists some recommended surface mount crystals and the parameters of each. This list is not exhaustive and other surface mount devices can be used with the ISL12008 if their specifications are very similar to the devices listed. The crystal should have a required parallel load capacitance of 12.5pF and an equivalent series resistance of less than 50k. The crystal’s temperature range specification should match the application. Many crystals are rated for -10°C to +60°C (especially through-hole and tuning fork types), so an appropriate crystal should be selected if extended temperature range is required. TABLE 7. SUGGESTED SURFACE MOUNT CRYSTALS MANUFACTURER PART NUMBER Citizen CM200S Epson MC-405, MC-406 Raltron RSM-200S SaRonix 32S12 Ecliptek ECPSM29T-32.768K ECS ECX-306 Fox FSM-327 Crystal Oscillator Frequency Adjustment The ISL12008 device contains circuitry for adjusting the frequency of the crystal oscillator. This circuitry can be used to trim oscillator initial accuracy as well as adjust the frequency to compensate for temperature changes. The Analog Trimming Register (ATR) is used to adjust the load capacitance seen by the crystal. There are 6 bits of ATR control, with linear capacitance increments available for adjustment. Since the ATR adjustment is essentially “pulling” the frequency of the oscillator, the resulting frequency changes will not be linear with incremental capacitance changes. The equations (which govern pulling) show that lower capacitor values of ATR adjustment will provide larger increments. Also, the higher values of ATR adjustment will produce smaller incremental frequency changes. The range afforded by the ATR adjustment with a typical surface mount crystal is typically -34ppm to +80ppm around the ATR = 0 default setting because of this property. The user should note this when using the ATR for calibration. The temperature drift of the capacitance used in the ATR control is extremely low, so this feature can be used for temperature compensation with good accuracy. Digital Trimming Register (DTR). The range provided is -63.0695ppm to +126.139ppm. DTR operates by adding or skipping pulses in the clock counter. It is very useful for coarse adjustments of frequency drift over temperature or extending the adjustment range available with the ATR register. Initial accuracy is best adjusted by enabling the 512Hz frequency output (using the FT bit, address 08h bit 6), and monitoring the FT/OUT pin with a calibrated frequency counter. The gating time should be set long enough to ensure accuracy to at least 1ppm. To calculate the ppm on the measured 512Hz, simply divide the measured 512Hz by 512, then subtract 1 from the result and mulitple by 1,000,000. Please see Equation 3 for the formula: (EQ. 3) ppm = (FT/512 - 1)*1E6 The ATR should be set to the center position, or 00000b, to begin with. Once the initial measurement is made, then the ATR register can be changed to adjust the frequency. Note for a range of 0 to 31 for the ATR register will increased capacitance and lower the frequency with 31 for the maximum negative correction, and for a range of 32 to 63 for the ATR register will decreased capacitance and increase the frequency with 32 for the maximum positive correction. If the initial measurement shows the frequency is far off, it will be necessary to use the DTR register to do a coarse adjustment. Note that most all crystals will have tight enough initial accuracy at room temperature so that a small ATR register adjustment should be all that is needed. Temperature Compensation The ATR and DTR controls can be combined to provide crystal drift temperature compensation. The typical 32.768kHz crystal has a drift characteristic that is similar to that shown in Figure 15. There is a turnover temperature (T0) where the drift is very near zero. The shape is parabolic as it varies with the square of the difference between the actual temperature and the turnover temperature. 0 -20 -40 -60 PPM Application Section -80 -100 -120 -140 -160 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 TEMPERATURE (°C) FIGURE 15. RTC CRYSTAL TEMPERATURE DRIFT In addition to the analog compensation afforded by the adjustable load capacitance, a digital compensation feature is available for the ISL12008. There are 6 bits known as the 16 FN6690.1 September 26, 2008 ISL12008 If full industrial temperature compensation is desired in an ISL12008 circuit, then both the DTR and ATR registers will need to be utilized (total correction range = -97.0695ppm to +206.139ppm). A system to implement temperature compensation would consist of the ISL12008, a temperature sensor, and a microcontroller. These devices may already be in the system so the function will just be a matter of implementing software and performing some calculations. Fairly accurate temperature compensation can be implemented just by using the crystal manufacturer’s specifications for the turnover temperature T0 and the drift coefficient (β). The formula for calculating the oscillator adjustment necessary is Equation 4: Adjustment(ppm) = ( T – T 0 )2 ∗ β Figure 17 shows a suggested layout for the ISL12008 device using a surface mount crystal. Two main precautions should be followed: 1. Do not run the serial bus lines or any high speed logic lines in the vicinity of the crystal. These logic level lines can induce noise in the oscillator circuit to cause misclocking. 2. Add a ground trace around the crystal with one end terminated at the chip ground. This will provide termination for emitted noise in the vicinity of the RTC device. (EQ. 4) Once the temperature curve for a crystal is established, then the designer should decide at what discrete temperatures the compensation will change. Since drift is higher at extreme temperatures, the compensation may not be needed until the temperature is greater than +20°C from T0. A sample curve of the ATR setting vs Frequency Adjustment for the ISL12008 and a typical RTC crystal is given in Figure 16. This curve may vary with different crystals, so it is good practice to evaluate a given crystal in an ISL12008 circuit before establishing the adjustment values. PPM ADJUSTMENT RTC circuit will avoid noise pickup and insure accurate clocking. 90 80 70 60 50 40 30 20 10 0 -10 -20 -30 -40 FIGURE 17. SUGGESTED LAYOUT FOR ISL12008 AND CRYSTAL In addition, it is a good idea to avoid a ground plane under the X1 and X2 pins and the crystal, as this will affect the load capacitance and therefore the oscillator accuracy of the circuit. If the FT/OUT pin is used as a clock, it should be routed away from the RTC device as well. The traces for the VBAT and VCC pins can be treated as a ground, and should be routed around the crystal. Super Capacitor Backup 0 5 10 15 20 25 30 35 40 45 50 55 60 ATR SETTING FIGURE 16. ATR SETTING vs OSCILLATOR FREQUENCY ADJUSTMENT This curve is then used to figure what ATR and DTR settings are used for compensation. The results would be placed in a lookup table for the microcontroller to access. Layout Considerations The crystal input at X1 has a very high impedance, and oscillator circuits operating at low frequencies (such as 32.768kHz) are known to pick up noise very easily if layout precautions are not followed. Most instances of erratic clocking or large accuracy errors can be traced to the susceptibility of the oscillator circuit to interference from adjacent high speed clock or data lines. Careful layout of the 17 The ISL12008 device provides a VBAT pin which is used for a battery backup input. A super capacitor can be used as an alternative to a battery in cases where shorter backup times are required. Since the battery backup supply current required by the ISL12008 is extremely low, it is possible to get months of backup operation using a super capacitor. Typical capacitor values are a few µF to 1F or more, depending on the application. If backup is only needed for a few minutes, then a small inexpensive electrolytic capacitor can be used. For extended periods, a low leakage, high capacity super capacitor is the best choice. These devices are available from such vendors as Panasonic and Murata. The main specifications include working voltage and leakage current. If the application is for charging the capacitor from a +5V ±5% supply with a signal diode, then the voltage on the capacitor can vary from ~4.5V to slightly over 5.0V. A capacitor with a rated WV of 5.0V may have a reduced lifetime if the supply voltage is slightly high. The leakage current should be as small as possible. For example, a super capacitor should be specified with leakage of well below 1µA. A standard electrolytic capacitor with DC leakage current in the microamps will have a severely shortened backup time. FN6690.1 September 26, 2008 ISL12008 Following are some examples with equations to assist with calculating backup times and required capacitance for the ISL12008 device. The backup supply current plays a major part in these equations, and a typical value was chosen for example purposes. For a robust design, a margin of 30% should be included to cover supply current and capacitance tolerances over the results of the calculations. Even more margin should be included if periods of very warm temperature operation are expected. EXAMPLE 1: CALCULATING BACKUP TIME GIVEN VOLTAGES AND CAPACITOR VALUE where: CBAT = 0.47F VBAT2 = 4.7V VBAT1 = 1.8V ILKG = 0 (assumed minimal) t BACKUP = 0.47 • ( 2.9 ) ⁄ 4.38E – 7 = 3.107E6s VBAT VCC tBACKUP = CBAT*(VBAT2 - VBAT1) / (IBATAVG + ILKG) seconds (EQ. 9) Solving Equation 8 for this example (IBATAVG = 4.387E-7A) yields Equation 10: 1N4148 2.7V TO 5.5V Combining with Equation 6 gives the equation for backup time in Equation 9: CBAT Since there are 86,400 seconds in a day, this corresponds to 35.96 days. If the 30% tolerance is included for capacitor and supply current tolerances, then worst case backup time would be represented in Equation 11: GND FIGURE 18. SUPERCAPACITOR CHARGING CIRCUIT In Figure 18, use CBAT = 0.47F and VCC = 5V. With VCC = 5V, the voltage at VBAT will approach 4.7V as the diode turns off completely. The ISL12008 is specified to operate down to VBAT = 1.8V. The capacitance charge/discharge in Equation 5 is used to estimate the total backup time as follows: (EQ. 5) I = CBAT*dV/dT Rearranging gives Equation 6: dT = CBAT*dV/ITOT to solve for backup time. (EQ. 6) CBAT is the backup capacitance and dV is the change in voltage from fully charged to loss of operation. Note that ITOT is the total of the supply current of the ISL12008 (IBAT) plus the leakage current of the capacitor and the diode, ILKG. In these calculations, ILKG is assumed to be extremely small and will be ignored. If an application requires extended operation at temperatures over +50°C, these leakages will increase and hence reduce backup time. Note that IBAT changes with VBAT almost linearly (see “Typical Performance Curves” on page 6). This allows us to make an approximation of IBAT, using a value midway between the two endpoints. The typical linear equation for IBAT vs VBAT is shown in Equation 7: IBAT = 1.031E-7*(VBAT) + 1.036E-7A (EQ. 10) (EQ. 7) Using Equation 7 to solve for the average current given 2 voltage points gives Equation 8: C BAT = 0.70 • 35.96 = 25.2 days (EQ. 11) EXAMPLE 2: CALCULATING A CAPACITOR VALUE FOR A GIVEN BACKUP TIME Referring to Figure 18 again, the capacitor value needs to be calculated to give 2 months (60 days) of backup time, given VCC = 5.0V. As in Example 1, the VBAT voltage will vary from 4.7V down to 1.8V. We will need to rearrange Equation 6 to solve for capacitance in Equation 12: (EQ. 12) CBAT = dT*I/dV Using the terms previously described, Equation 12 becomes Equation 13: CBAT = tBACKUP*(IBATAVG + ILKG)/(VBAT2 – VBAT1) (EQ. 13) where: tBACKUP = 60 days*86,400 sec/day = 5.18 E6 seconds IBATAVG = 4.387 E-7A (same as Example 1) ILKG = 0 (assumed) VBAT2 = 4.7V VBAT1 = 1.8VSolving gives CBAT = 5.18 E6*(4.387 E-7)/(2.9) = 0.784F If the 30% tolerance is included for tolerances, then worst case capacitor value would be: C BAT = 1.3 • 0.784 = 1.02F (EQ. 14) IBATAVG = 5.155E-8*(VBAT2 + VBAT1) + 1.036E-7A (EQ. 8) 18 FN6690.1 September 26, 2008 ISL12008 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA H 0.25(0.010) M B M INCHES E SYMBOL -B- 1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e α B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N α NOTES: MILLIMETERS 8 0° 8 8° 0° 7 8° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 19 FN6690.1 September 26, 2008