(NA6223-AL)

Document 1139
Flyback Transformer
For Texas Instruments
TPS23753A PoE controller
• Flyback transformer for 10 W PoE applications
• Developed to work with TI TPS23753A PoE controller (PMP8896
and PMP9175 Reference Design)
• 1500 Vrms isolation from primary and bias to secondary and sync
Core material Ferrite
Terminations RoHS tin-silver (96.5/3.5) over tin over nickel over phos
bronze.
Weight 6.2 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel Plastic tape: 32 mm wide, 0.5 mm thick,
28 mm pocket spacing, 12.93 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
4
Leakage
DCR max (Ohms) inductance
Turns ratio6
Part L at 0A2 L at Ipk3
1
number ±10% (µH) min (µH) pri sec bias sync max (µH)5pri : sec pri : bias pri : sync
NA6223-AL_
180
162
0.330 0.0135 0.230
0.190
1. When ordering, please specify packaging code:
NA6223-ALD
Packaging:D=13″ machine-ready reel. EIA-481 embossed plastic
tape (175 parts per full reel).
B=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is for the primary, measured at 1 kHz, 0.5 Vrms, 0 Adc.
0.512
13,00
XXXX Y
0.530 max
13,46
1
NA6223-AL
5
Dot indicates pin 1
Internal code
1.20
1 : 0.1671 : 0.3611 : 0.167
W1B
Pri
0.080
2,03
5
Sync
W5
7
Sec
W1A
10
1
3
1
0.590
14,99
6
2
0.050
1,27
Recommended
Land Pattern
0.098
2,50
5.0 V, 2.0 A
3. Peak primary current (1.1 A) drawn at minimum input voltage.
4. DCR for the primary is from pin 1 to pin 2.
5. Leakage inductance measured between pins 1 and 2 with all other
windings shorted.
6. Turns ratio is with the primary windings connected in series.
7. Output is between pins 7 and 10. Bias winding output is 10 V, 20 mA.
Sync winding output is a 5 V Sync FET gate drive signal.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.028
6 0,70
10
Output7
0.098
2,50
Bias
W3
4
0.500 max
12,70
0.039
1,00
0.004 /0,10
0.699 max
17,75
Dimensions are in
inches
mm
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
Document 1139 Revised 08/08/13
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.