Digital DC/DC PMBus 17A Module ZL9117M Features The ZL9117M is a 17A, variable output, step-down PMBus-compliant digital power supply. Included in the module is a high-performance digital PWM controller, power MOSFETs, an inductor, and all the passive components required for a highly integrated DC/DC power solution. This power module has built-in auto-compensation algorithms, which eliminates the need for manual compensation design work. The ZL9117M operates over a wide input voltage range and supports an output voltage range of 0.6V to 3.6V, which can be set by external resistors or via PMBus. This high-efficiency power module is capable of delivering 17A. Only bulk input and output capacitors are needed to finish the design. The output voltage can be precisely regulated to as low as 0.6V with ±1% output voltage regulation over line, load, and temperature variations. • Complete Digital Switch Mode Power Supply The ZL9117M features auto-compensation, internal soft-start, auto-recovery overcurrent protection, an enable option, and pre-biased output start-up capabilities. • Industrial and Medical Equipment • Fast Transient Response • Auto Compensating PID Filter • External Synchronization • Output Voltage Tracking • Current Sharing • Programmable Soft-start Delay and Ramp • Overcurrent/Undercurrent Protection • PMBus Compliant Applications • Server, Telecom, and Datacom • General Purpose Point of Load Related Literature The ZL9117M is packaged in a thermally enhanced, compact (15mmx15mm) and low profile (3.5mm) over-molded QFN package module suitable for automated assembly by standard surface mount equipment. The ZL9117M is Pb-free and RoHS compliant. • See AN2033, “Zilker Labs PMBus Command Set for DDC Products” • See AN2034, “Configuring Current Sharing on the ZL2004 and ZL2006” Figure 1 represents a typical implementation of the ZL9117M. For PMBus operation, it is recommended to tie the Enable pin (EN) to SGND. V DRV 4.7µF 16V 10µF 16V 4.5V TO 6.5V 10µF 16V 4.7µF 16V V IN 4.5V TO 13.2V EN EXT SYNC DDC BUS VR VDD PG ENABLE V25 POWER GOOD OUTPUT VDRV 2 x 22µF 16V VIN (EPAD) V OUT VOUT (EPAD) SYNC ZL9117M 2 SW (EPAD) DDC 3 x 100µF 6.3V 3 SCL FB+ PGND (EPAD) RTN FB- SA SGND SDA VTRK I C/SMBus 1 VSET 2 R SA R SET Notes: 1. The I2C/SMBus requires pull-up resistors. Please refer to the I2C/SMBus specifications for more details. 2. The DDC bus requires a pull-up resistor. The resistance will vary based on the capacitive loading of the bus (and on the number of devices connected). The 10k default value, assuming a maximum of 100pF per device, provides the necessary 1µs pull-up rise time. Please refer to the Digital-DC Bus section for more details. 3. Additional capacitance may be required to meet specific transient response targets. 4. The VR, V25, VDRV, and VDD capacitors should be placed no farther than 0.5 cm from the pin. FIGURE 1. 17A APPLICATION CIRCUIT October 21, 2011 FN7914.1 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ZL9117M Pin Configuration SGND VR DDC EN PG SYNC SA SCL ZL9117M (21 LD QFN) TOP VIEW 9 8 7 6 5 4 3 2 1 SDA PGND 10 21 VSET V25 11 20 VTRK VDD 12 19 FB+ VDRV 13 18 FB- SW 14 VOUT 17 VIN 15 PGND 16 Pin Descriptions PIN LABEL TYPE DESCRIPTION 1 SDA I/O Serial data. 2 SCL I/O Serial clock. 3 SA I Serial address select pin. Used to assign unique SMBus address to each module. 4 SYNC I/O Clock synchronization. Used for synchronization to external frequency reference. 5 PG O Power-good output. 6 EN I Enable input (factory setting active high). Pull up to enable PWM switching and pull down to disable PWM switching. 7 DDC I/O 8 VR PWR Internal 5V reference used to power internal drivers. Connect 4.7μF bypass capacitor to this pin. 9 SGND PWR Signal ground. Connect to low impedance ground plane. 10 PGND PWR Power ground. Connect to low impedance ground plane. 11 V25 PWR Internal 2.5V reference used to power internal circuitry. Connect 4.7μF bypass capacitor to this pin. 12 VDD PWR Input supply voltage for controller. Connect 4.7μF bypass capacitor to this pin. 13 VDRV PWR Power supply for internal FET drivers. Connect 10μF bypass capacitor to this pin. 14 (epad) SW PWR Drive train switch node 15 (epad) VIN PWR Power supply input FET voltage. 16 (epad) PGND PWR Power ground. Connect to low impedance ground plane. 17 (epad) VOUT PWR Power supply output voltage. Output voltage from PWM. 18 FB- I Output voltage feedback. Connect to load return of ground regulation point. 19 FB+ I Output voltage feedback. Connect to output regulation point. 20 VTRK I Tracking sense input. Used to track an external voltage source. 21 VSET I Output voltage selection pin. Used to set VOUT set point and VOUT max. Digital-DC bus (open drain). Interoperability between Zilker Labs modules. 2 FN7914.1 October 21, 2011 ZL9117M Ordering Information PART NUMBER (Notes 1, 2, 3) ZL9117MIRZ PART MARKING ZL9117M TEMP RANGE (°C) -40 to +85 PACKAGE (Pb-Free) 21 Ld 15x15 QFN PKG. DWG. # L21.15x15 NOTES: 1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ZL9117M. For more information on MSL please see Tech Brief TB363. 3 FN7914.1 October 21, 2011 ZL9117M Absolute Maximum Ratings (Note 4) Thermal Information DC Supply Voltage for VDD Pin . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 15.7V Input Voltage for VIN Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 15.7V MOSFET Drive Reference for VR Pin . . . . . . . . . . . . . . . . . . . . -0.3V to 6.5V 2.5V Logic Reference for V25 Pin. . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 3V MOSFET Driver Power for VDRV Pin . . . . . . . . . . . . . . . . . . . . . .-0.3V to 7.5V Logic I/O Voltage for DDC, EN, FB+, FB-, PG, SA, SCL, SDA, SYNC, VSET Pins . . . . . . . . . . . . -0.3V to 6V ESD Rating Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . . 2000V Machine Model (Tested per JESD22-A115C) . . . . . . . . . . . . . . . . . . 200V Charged Device Model (Tested per JESD22-C110D) . . . . . . . . . . . 1000V Latch Up (Tested per JESD78C; Class 2, Level A) . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) θJA (°C/W) θJC (°C/W) QFN Package (Notes 7, 8) . . . . . . . . . . . . . . 11.5 2.2 Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +150°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to +150°C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Input Supply Voltage Range, VIN . . . . . . . . . . . . . . . . . . . . . . 4.5V to 13.2V Input Supply For Controller, VDD (Note 5) . . . . . . . . . . . . . . . . 4.5V to 13.2V Driver Supply Voltage, VDRV . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 6.5V Output Voltage Range, VOUT (Note 6) . . . . . . . . . . . . . . . . . . . 0.54V to 3.6V Output Current Range, IOUT(DC) (Note 19). . . . . . . . . . . . . . . . . . . 0A to 17A Operating Junction Temperature Range, TJ. . . . . . . . . . . .-40°C to +125°C CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. Voltage measured with respect to SGND. 5. VIN supplies the power FETs. VDD supplies the controller. VIN can be tied to VDD. For VDD ≤ 5.5V, VDD should be tied to VR. 6. Includes ±10% margin limits. 7. θJA is simulated in free air with device mounted on a four-layer FR-4 test board (76.2 x 114.3 x 1.6mm) with 80% coverage, 2oz Cu on top and bottom layers, plus two, buried, one-ounce Cu layers with coverage across the entire test board area. Multiple vias were used, with via diameter = 0.3mm on 1.2mm pitch. 8. For θJC, the “case” temperature is measured at the center of the package underside. Electrical Specifications VDD = 12V, TA = -40°C to +85°C unless otherwise noted. Typical values are at TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +85°C. PARAMETER CONDITIONS MIN TYP MAX (Note 9) (Note 10) (Note 9) UNIT INPUT AND SUPPLY CHARACTERISTICS Input Bias Supply Current, IDD VIN = VDD = 13.2V, fSW = 571kHz, No load – 20 40 mA Input Bias Shutdown Current, IDDS EN = 0V, No I2C/SMBus activity – 15.5 20 mA Input Supply Current, IVIN VIN = 12V, IOUT = 17A, VOUT = 1.0V – 1.78 – A Driver Supply Current, IVDRV Not switching – 190 250 µA VR Reference Output Voltage (Note 11) VDD > 6V, IVR < 20mA 4.5 5.2 5.7 V V25 Reference Output Voltage (Note 11) VR > 3V, IV25 < 20mA 2.25 2.5 2.75 V Output Load Current (Notes 18, 19) VIN = 12V, VOUT = 1.0V – 17 – A Line Regulation Accuracy, ΔVOUT/ΔVIN (Note 12) VOUT = 1.0V, IOUT = 0A, VIN = 5V to 13.2V OUTPUT CHARACTERISTICS – 0.5 – % Load Regulation Accuracy, ΔVOUT/ΔIOUT (Note 12) IOUT = 0A to 17A, VOUT = 1.0V – 0.5 – % Peak-to-peak Output Ripple Voltage, ΔVOUT (Note 12) IOUT = 17A, VOUT = 1.0V, COUT = 3000µF – 6 – mV Soft-start Delay Duration Range (Notes 11, 13) Set using I2C/SMBus 2 – 200 ms Soft-start Delay Duration Accuracy (Note 11) Turn-on delay (precise mode) (Notes 13, 14) – ±0.25 – ms Turn-on delay (normal mode) (Note 15) – -0.25/+4 – ms Turn-off delay (Note 15) – -0.25/+4 – ms Set using I2C 0 – 200 ms – 100 – µs Soft-start Ramp Duration Range (Note 11) Soft-start Ramp Duration Accuracy (Note 11) DYNAMIC CHARACTERISTICS Voltage Change for Positive Load Step ΔIOUT = 6A, slew rate = 2.5A/μs, VOUT = 1.0V, COUT = 3000µF – 3 – % Voltage Change for Negative Load Step ΔIOUT = 6A, slew rate = 2.5A/μs, VOUT = 1.0V, COUT = 3000µF – 3 – % 4 FN7914.1 October 21, 2011 ZL9117M Electrical Specifications VDD = 12V, TA = -40°C to +85°C unless otherwise noted. Typical values are at TA = +25°C. Boldface limits apply over the operating temperature range, -40°C to +85°C. (Continued) PARAMETER CONDITIONS MIN TYP MAX (Note 9) (Note 10) (Note 9) UNIT OSCILLATOR AND SWITCHING CHARACTERISTICS (Note 11) Switching Frequency Range Maximum PWM Duty Cycle Factory setting 571 1000 kHz 95 – – % 150 – – ns External clock source -13 – 13 % EN, PG, SCL, SDA pins -10 – 10 µA – – 0.8 V Minimum SYNC Pulse Width Input clock Frequency Drift Tolerance 500 LOGIC INPUT/OUTPUT CHARACTERISTICS (Note 11) Logic Input Bias Current Logic Input Low, VIL 2.0 – – V Logic Output Low, VOL IOL ≤ 4mA (Note 17) – – 0.4 V Logic Output High, VOH IOH ≥ -2mA (Note 17) 2.25 – – V Configurable via I2C/SMBus 2.85 – 16 V -150 – 150 mV Logic Input High, VIH FAULT PROTECTION CHARACTERISTICS (Note 11) UVLO Threshold Range UVLO Set-point Accuracy UVLO Hysteresis Factory setting – 3 – % Configurable via I2C/SMBus 0 – 100 % – – 2.5 µs – 90 – % VOUT UVLO Delay Power-Good VOUT Threshold Factory setting Power-Good VOUT Hysteresis Factory setting – 5 – % Power-Good Delay (Note 16) Configurable via I2C/SMBus 0 – 200 ms VSEN Undervoltage Threshold VSEN Overvoltage Threshold Factory setting – 85 – % VOUT Configurable via I2C/SMBus 0 – 110 % VOUT Factory setting – 115 – % VOUT Configurable via I2C/SMBus 0 – 115 % VOUT VSEN Undervoltage Hysteresis – 5 – % VOUT VSEN Undervoltage/Overvoltage Fault Response Time Factory setting – 16 – µs Configurable via I2C/SMBus 5 – 60 µs Thermal Protection Threshold (Controller Junction Temperature) Factory setting – 125 – °C -40 – 125 °C – 15 – °C Configurable via I2C/SMBus Thermal Protection Hysteresis NOTES: 9. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design. 10. Parameters with TYP limits are not production tested unless otherwise specified. 11. Parameters are 100% tested for internal controller prior to module assembly. 12. VOUT measured at the termination of the FB+ and FB- sense points. 13. The device requires a delay period following an enable signal and prior to ramping its output. Precise timing mode limits this delay period to approximately 2ms, where in normal mode it may vary up to 4ms. 14. Precise ramp timing mode is only valid when using the EN pin to enable the device rather than PMBus enable. 15. The devices may require up to a 4ms delay following the assertion of the enable signal (normal mode) or following the de-assertion of the enable signal. 16. Factory setting for Power-Good delay is set to the same value as the soft-start ramp time. 17. Nominal capacitance of logic pins is 5pF. 18. This condition is tested on the Intersil 3-module evaluation board at +50°C ambient temperature and 400LFM air flow. 19. The load current is related to the thermal derating curves. The maximum allowed current is derated while the output voltage goes higher than 2.5V. 5 FN7914.1 October 21, 2011 ZL9117M Typical Performance Curves Operating condition: TA = +25°C, No air flow, FSW = 571kHz. VDRV = 5V. COUT = 3000µF. Typical values are used unless otherwise noted. 100 100 2.5V 3.3V 95 1.8V 2.5V 1.8V 95 EFFICIENCY (%) EFFICIENCY (%) 3.3V 90 85 1.0V 1.2V 80 90 85 75 75 70 0 2 4 6 8 10 12 OUTPUT CURRENT (A) 14 16 70 18 FIGURE 2. EFFICIENCY, VIN = 5V, FOR VARIOUS OUTPUT VOLTAGES LISTED 2 4 6 8 10 12 OUTPUT CURRENT (A) 14 16 18 35 VOLTAGE DEVIATION (mV) 1.8V 2.5V 95 EFFICIENCY (%) 0 FIGURE 3. EFFICIENCY, VIN = 9V, FOR VARIOUS OUTPUT VOLTAGES LISTED 100 3.3V 90 85 1.2V 1.0V 80 75 70 1.2V 1.0V 80 0 2 4 6 8 10 12 OUTPUT CURRENT (A) 14 16 VIN = 12V 30 VOUT = 1.2V I STEP = 12A TO 6A 25 OUT SLEW 2.5A/µs 20 15 10 5 0 -5 18 0 FIGURE 4. EFFICIENCY, VIN = 12V, FOR VARIOUS OUTPUT VOLTAGES LISTED 0.1 0.2 0.3 0.4 0.5 0.6 TIME (ms) 0.7 0.8 0.9 1.0 FIGURE 5. DYNAMIC RESPONSE, UNLOADING TIME (ms) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.4 0 -5 VOUT (V) VOLTAGE DEVIATION (mV) 5 0 -10 -15 VIN = 12V -20 V OUT = 1.2V -25 IOUT STEP = 6A TO 12A VIN = 12V 1.2 VOUT = 1.2V 1.0 tRISE = 5ms 0.8 0.6 0.4 0.2 0 SLEW 2.5A/µs -0.2 -30 FIGURE 6. DYNAMIC RESPONSE, LOADING 6 0 1 2 3 4 5 6 TIME (ms) 7 8 9 10 FIGURE 7. SOFT-START RAMP-UP FN7914.1 October 21, 2011 ZL9117M Typical Performance Curves Operating condition: TA = +25°C, No air flow, FSW = 571kHz. VDRV = 5V. COUT = 3000µF. Typical values are used unless otherwise noted. (Continued) 1.4 VIN = 12V 1.2 VOUT = 1.2V 1.0 tFALL = 5ms VOUT (V) 0.8 0.6 0.4 0.2 0 -0.2 0 1 2 3 4 5 6 TIME (ms) 7 8 9 10 FIGURE 8. RAMP-DOWN Derating Curves Operating conditions: TA = +25°C, FSW = 571kHz. VDRV = 5V. COUT = 3000µF. Typical values are used unless otherwise noted. 20 NO AIR FLOW 18 MAX. LOAD CURRENT (A) MAX. LOAD CURRENT (A) 20 16 14 12 10 3.3V 8 1.0V 6 4 16 14 12 10 0 120 130 1.8V 4 2 70 80 90 100 110 AMBIENT TEMPERATURE (°C) 2.5V 6 0 60 3.3V 8 2 50 NO AIR FLOW 18 1.0V 50 60 70 80 90 100 110 120 130 AMBIENT TEMPERATURE (°C) FIGURE 9. DERATING CURVE, 5VIN, FOR VARIOUS OUTPUT VOLTAGES LISTED FIGURE 10. DERATING CURVE, 12VIN, FOR VARIOUS OUTPUT VOLTAGES LISTED 7 7 1.8V 6 6 5 4 LOSS (W) LOSS (W) 5 3.3V 3 1.0V 2 3.3V 3 1.2V 1 0 2 4 6 8 10 12 14 16 18 OUTPUT CURRENT (A) FIGURE 11. POWER LOSS CURVE, 5VIN, FOR VARIOUS OUTPUT VOLTAGES LISTED 7 2.5V 4 2 1.2V 1 0 1.8V 2.5V 0 1.0V 0 2 4 6 8 10 12 OUTPUT CURRENT (A) 14 16 18 FIGURE 12. POWER LOSS CURVE, 12VIN, FOR VARIOUS OUTPUT VOLTAGES LISTED FN7914.1 October 21, 2011 ZL9117M Functional Description TABLE 1. OUTPUT VOLTAGE RESISTOR SETTINGS (Continued) I2C/SMBus Communications The ZL9117M provides an I2C/SMBus digital interface that enables the user to configure all aspects of the module operation as well as monitor the input and output parameters. The ZL9117M can be used with any I2C host device. In addition, the module is compatible with SMBus version 2.0. Pull-up resistors are required on the I2C/SMBus as specified in the SMBus 2.0 specification. The ZL9117M accepts most standard PMBus commands. When controlling the device with PMBus commands, it is recommended that the enable pin is tied to SGND. The SMBus device address and VOUT_MAX are the only parameters that must be set by external pins. All other device parameters can be set via the I2C/SMBus. The device address is set using the SA pin. VOUT_MAX is determined as 10% greater than the voltage set by the VSET pin. Standard 1% resistor values are used between the respective pin and SGND. Output Voltage Selection The output voltage may be set to a voltage between 0.6V and 3.6V provided that the input voltage is higher than the desired output voltage by an amount sufficient to prevent the device from exceeding its maximum duty cycle specification. The VSET pin is used to set the output voltage to levels as shown in Table 1. The RSET resistor is placed between the VSET pin and SGND. TABLE 1. OUTPUT VOLTAGE RESISTOR SETTINGS VOUT (V) RSET (kΩ) 1.80 61.9 1.90 68.1 2.00 75 2.10 82.5 2.20 90.9 2.30 100 2.50 110 2.80 121 3.00 133 3.30 147 The output voltage may also be set to any value between 0.6V and 3.6V using a PMBus command over the I2C/SMBus interface. See Application Note AN2033 for details. The RSET resistor program places an upper limit in output voltage setting through PMBUS programming to 10% above the value set by the resistor. Soft-start Delay and Ramp Times It may be necessary to set a delay from when an enable signal is received until the output voltage starts to ramp to its target value. In addition, the designer may wish to precisely set the time required for VOUT to ramp to its target value after the delay period has expired. These features may be used as part of an overall in-rush current management strategy or to precisely control how fast a load IC is turned on. The ZL9117M gives the system designer several options for precisely and independently controlling both the delay and ramp time periods. VOUT (V) RSET (kΩ) 0.60 10 0.65 11 0.70 12.1 0.75 13.3 0.80 14.7 0.85 16.2 0.90 17.8 0.95 19.6 1.00 21.5 1.05 23.7 1.10 26.1 1.15 28.7 Power-Good 1.20 31.6 1.25 34.8 1.30 38.3 1.40 42.2 1.50 46.4 The ZL9117M provides a Power-Good (PG) signal that indicates the output voltage is within a specified tolerance of its target level and no fault condition exists. By default, the PG pin asserts if the output is within 10% of the target voltage. These limits and the polarity of the pin may be changed via the I2C/SMBus interface. See Application Note AN2033 for details. 1.60 51.1 1.70 56.2 8 The soft-start delay period begins when the EN pin is asserted and ends when the delay time expires. The soft-start delay and ramp times are set to custom values via the I2C/SMBus interface. When the delay time is set to 0ms, the device begins its ramp-up after the internal circuitry has initialized (approximately 2ms). When the soft-start ramp period is set to 0ms, the output ramps up as quickly as the output load capacitance and loop settings allow. It is generally recommended to set the soft-start ramp to a value greater than 500µs to prevent inadvertent fault conditions due to excessive in-rush current. A PG delay period is defined as the time from when all conditions within the ZL9117M for asserting PG are met to when the PG pin is actually asserted. This feature is commonly used instead of FN7914.1 October 21, 2011 ZL9117M using an external reset controller to control external digital logic. By default, the ZL9117M PG delay is set equal to the soft-start ramp time setting. Therefore, if the soft-start ramp time is set to 10ms, the PG delay is set to 10ms. The PG delay may be set independently of the soft-start ramp using the I2C/SMBus as described in Application Note AN2033. Switching Frequency and PLL The ZL9117M incorporates an internal phase-locked loop (PLL) to clock the internal circuitry. The PLL can be driven by an external clock source connected to the SYNC pin. When using the internal oscillator, the SYNC pin can be configured as a clock source. The internal switching frequency of the ZL9117M is 571kHz. Please refer to Application Note AN2033 for details on how to configure the UVLO threshold or to select specific UVLO fault response options via the I2C/SMBus interface. Output Overvoltage Protection The ZL9117M offers an internal output overvoltage protection circuit that can be used to protect sensitive load circuitry from being subjected to a voltage higher than its prescribed limits. A hardware comparator is used to compare the actual output voltage (seen at the FB+ pin) to a threshold set to 15% higher than the target output voltage (the default setting). If the FB+ voltage exceeds this threshold, the PG pin de-asserts, and the controller can then respond in a number of ways, as follows: Loop Compensation 1. Initiate an immediate shutdown until the fault is cleared. The user can select a specific number of retry attempts. The ZL9117M operates as a voltage-mode synchronous buck controller with a fixed frequency PWM scheme. The module is internally compensated via the I2C/SMBus interface. 2. Turn off the high-side MOSFET and turn on the low-side MOSFET. The low-side MOSFET remains ON until the device attempts a restart. The ZL9117M has an auto compensation feature that measures the characteristics of the power train and calculates the proper tap coefficients. By default, auto compensation is configured to execute one time after ramp with 50% Auto Comp Gain with Power-Good asserted immediately after the first Auto Comp cycle completes. The default response from an overvoltage fault is to immediately shut down. The controller continuously checks for the presence of the fault condition, and when the fault condition no longer exists, the device is re-enabled. Please refer to Application Note AN2033 for further details. For continuous overvoltage protection when operating from an external clock, the only allowed response is an immediate shutdown. Adaptive Diode Emulation Please refer to Application Note AN2033 for details on how to select specific overvoltage fault response options via I2C/SMBus. Adaptive diode emulation mode turns off the low-side FET gate drive at low load currents to prevent the inductor current from going negative, reducing the energy losses and increasing overall efficiency. Diode emulation is available to single-phase devices only. Note: the overall bandwidth of the device may be reduced when in diode emulation mode. Disabling the diode emulation prior to applying significant load steps is recommended. Input Undervoltage Lockout The input undervoltage lockout (UVLO) prevents the ZL9117M from operating when the input falls below a preset threshold, indicating the input supply is out of its specified range. The UVLO threshold (VUVLO) can be set between 2.85V and 16V using the I2C/SMBus interface. Once an input undervoltage fault condition occurs, the device can respond in a number of ways, as follows: 1. Continue operating without interruption. 2. Continue operating for a given delay period, followed by shutdown if the fault still exists. The device remains in shutdown until instructed to restart. Output Pre-Bias Protection An output pre-bias condition exists when an externally applied voltage is present on a power supply’s output before the power supply’s control IC is enabled. Certain applications require that the converter not be allowed to sink current during start-up if a pre-bias condition exists at the output. The ZL9117M provides pre-bias protection by sampling the output voltage prior to initiating an output ramp. If a pre-bias voltage lower than the target voltage exists after the pre-configured delay period has expired, the target voltage is set to match the existing pre-bias voltage, and both drivers are enabled. The output voltage is then ramped to the final regulation value at the preconfigured ramp rate. The actual time the output takes to ramp from the pre-bias voltage to the target voltage varies, depending on the pre-bias voltage, however, the total time elapsed from when the delay period expires and when the output reaches its target value will match the pre-configured ramp time. See Figure 13. 3. Initiate an immediate shutdown until the fault is cleared. The user can select a specific number of retry attempts. The default response from a UVLO fault is an immediate shutdown of the module. The controller continuously checks for the presence of the fault condition. If the fault condition is no longer present, the ZL9117M is re-enabled. 9 FN7914.1 October 21, 2011 ZL9117M 3. Continue operating for a given delay period, followed by shutdown if the fault still exists. 4. Continue operating through the fault (this could result in permanent damage to the power supply). 5. Initiate an immediate shutdown. The default response from an overcurrent fault is an immediate shutdown of the controller. The controller continuously checks for the presence of the fault condition, and if the fault condition no longer exists, the device is re-enabled. Please refer to Application Note AN2033 for details on how to select specific overcurrent fault response options via I2C/SMBus. Thermal Overload Protection The ZL9117M includes a thermal sensor that continuously measures the internal temperature of the module and shuts down the controller when the temperature exceeds the preset limit. The default temperature limit is set to +125°C in the factory, but the user may set the limit to a different value if desired. See Application Note AN2033 for details. Note that setting a higher thermal limit via the I2C/SMBus interface may result in permanent damage to the controller. Once the module has been disabled due to an internal temperature fault, the user may select one of several fault response options as follows: 1. Initiate a shutdown and attempt to restart an infinite number of times with a preset delay period between attempts. FIGURE 13. OUTPUT RESPONSES TO PRE-BIAS VOLTAGES If a pre-bias voltage higher than the target voltage exists after the pre-configured delay period has expired, the target voltage is set to match the existing pre-bias voltage, and both drivers are enabled with a PWM duty cycle that would ideally create the pre-bias voltage. Once the pre-configured soft-start ramp period has expired, the PG pin is asserted (assuming the pre-bias voltage is not higher than the overvoltage limit). The PWM then adjusts its duty cycle to match the original target voltage, and the output ramps down to the preconfigured output voltage. If a pre-bias voltage higher than the overvoltage limit exists, the device does not initiate a turn-on sequence and declares an overvoltage fault condition to exist. In this case, the device responds based on the output overvoltage fault response method that has been selected. See “Output Overvoltage Protection” on page 9 for response options due to an overvoltage condition. Note that pre-bias protection is not offered for current sharing groups that also have tracking enabled. VDD must be tied to VIN for proper prebias start-up in single module operation. Output Overcurrent Protection The ZL9117M can protect the power supply from damage if the output is shorted to ground or if an overload condition is imposed on the output. The following overcurrent protection response options are available: 1. Initiate a shutdown and attempt to restart an infinite number of times with a preset delay period between attempts. 2. Initiate a shutdown and attempt to restart a preset number of times with a preset delay period between attempts. 3. Continue operating for a given delay period, followed by shutdown if the fault still exists. 4. Continue operating through the fault (this could result in permanent damage to the power supply). 5. Initiate an immediate shutdown. If the user has configured the module to restart, the controller waits the preset delay period (if configured to do so) and then checks the module temperature. If the temperature has dropped below a threshold that is approximately +15°C lower than the selected temperature fault limit, the controller attempts to re-start. If the temperature still exceeds the fault limit, the controller waits the preset delay period and retries again. The default response from a temperature fault is an immediate shutdown of the module. The controller continuously checks for the fault condition, and once the fault has cleared, the ZL9117M is re-enabled. Please refer to Application Note AN2033 for details on how to select specific temperature fault response options via I2C/SMBus. I2C/SMBus Module Address Selection Each module must have its own unique serial address to distinguish between other devices on the bus. The module address is set by connecting a resistor between the SA pin and SGND. Table 2 lists the available module addresses. 2. Initiate a shutdown and attempt to restart a preset number of times with a preset delay period between attempts. 10 FN7914.1 October 21, 2011 ZL9117M should be limited to a value that enables any device to assert the bus to a voltage that ensures a logic 0 (typically 0.8V at the device monitoring point), given the pull-up voltage and the pull-down current capability of the ZL9117M (nominally 4mA). TABLE 2. SMBus ADDRESS RESISTOR SELECTION RSA (kΩ) SMBus ADDRESS 10 0x19 11 0x1A 12.1 0x1B 13.3 0x1C 14.7 0x1D 16.2 0x1E 17.8 0x1F 19.6 0x20 21.5 0x21 23.7 0x22 26.1, or connect to SGND 0x23 28.7, or Open 0x24 31.6, or connect to V25 or VR 0x25 To enable phase spreading, all converters must be synchronized to the same switching clock. The phase offset of each device may also be set to any value between 0° and 360° in 22.5° increments via the I2C/SMBus interface. Refer to Application Note AN2033 for further details. 34.8 0x26 Output Sequencing 38.3 0x27 42.2 0x28 46.4 0x29 51.1 0x2A 56.2 0x2B A group of Digital-DC modules or devices may be configured to power-up in a predetermined sequence. This feature is especially useful when powering advanced processors, FPGAs and ASICs that require one supply to reach its operating voltage; prior to another supply reaching its operating voltage in order to avoid latch-up. Multi-device sequencing can be achieved by configuring each device through the I2C/SMBus interface. 61.9 0x2C 68.1 0x2D 75 0x2E 82.5 0x2F 90.9 0x30 100 0x31 Phase Spreading When multiple point-of-load converters share a common DC input supply, it is desirable to adjust the clock phase offset of each device such that not all devices start to switch simultaneously. Setting each converter to start its switching cycle at a different point in time, can dramatically reduce input capacitance requirements and efficiency losses. Since the peak current drawn from the input supply is effectively spread out over a period of time, the peak current drawn at any given moment is reduced, and the power losses proportional to the IRMS2 are reduced dramatically. Multiple device sequencing is configured by issuing PMBus commands to assign the preceding device in the sequencing chain as well as the device that follows in the sequencing chain. The Enable pins of all devices in a sequencing group must be tied together and driven high to initiate a sequenced turn-on of the group. Enable must be driven low to initiate a sequenced turnoff of the group. Refer to Application Note AN2033 for details on sequencing via the I2C/SMBus interface. Digital-DC Bus The Digital-DC Communications (DDC) bus is used to communicate between Zilker Labs Digital-DC modules and devices. This dedicated bus provides the communication channel between devices for features such as sequencing, fault spreading, and current sharing. The DDC pin on all Digital-DC devices in an application should be connected together. A pull-up resistor is required on the DDC bus in order to guarantee the rise time as shown in Equation 1: (EQ. 1) Rise Time = R PU∗ C LOAD ≈ 1μs where RPU is the DDC bus pull-up resistance and CLOAD is the bus loading. The pull-up resistor may be tied to an external 3.3V or 5V supply as long as this voltage is present prior to or during device power-up. As rules of thumb, each device connected to the DDC bus presents approximately 10pF of capacitive loading, and each inch of FR4 PCB trace introduces approximately 2pF. The ideal design uses a central pull-up resistor that is well-matched to the total load capacitance. The minimum pull-up resistance 11 Fault Spreading Digital DC modules and devices can be configured to broadcast a fault event over the DDC bus to the other devices in the group. When a non-destructive fault occurs and the device is configured to shut down on a fault, the device shuts down and broadcasts the fault event over the DDC bus. The other devices on the DDC bus shut down simultaneously, if configured to do so, and attempt to re-start in their prescribed order, if configured to do so. Active Current Sharing Paralleling multiple ZL9117M modules can be used to increase the output current capability of a single power rail. By connecting the DDC pins of each module together and configuring the modules as a current sharing rail, the units share the current equally within a few percent. Figure 14 illustrates a typical connection for two modules. FN7914.1 October 21, 2011 ZL9117M The ISHARE_CONFIG command is used to configure the module for active current sharing. The default setting is a stand-alone non-current sharing module. A current sharing rail can be part of a system sequencing group. . VIN 3.3V TO 5V CIN DDC ZL9117M For fault configuration, the current share rail is configured in a quasi-redundant mode. In this mode, when a member module fails, the remaining members continue to operate and attempt to maintain regulation. Of the remaining modules, the module with the lowest member position becomes the reference. If fault spreading is enabled, the current share rail failure is not broadcast until the entire current share rail fails. COUT CIN DDC ZL9117M VOUT COUT Phase Offset = SMBus Address [ 4:0 ] – Current Share Position∗ 22.5° FIGURE 14. CURRENT SHARING GROUP The ZL9117M uses a low-bandwidth, first-order digital current sharing technique to balance the unequal module output loading by aligning the load lines of member modules to a reference module. Droop resistance is used to add artificial resistance in the output voltage path to control the slope of the load line curve, calibrating out the physical parasitic mismatches due to power train components and PCB layout. Upon system start-up, the module with the lowest member position as selected in ISHARE_CONFIG is defined as the reference module. The remaining modules are members. The reference module broadcasts its current over the DDC bus. The members use the reference current information to trim their voltages (VMEMBER) to balance the current loading of each module in the system. (EQ. 3) Please refer to Application Note AN2034 for additional details on current sharing. Phase Adding/Dropping The ZL9117M allows multiple power converters to be connected in parallel to supply higher load currents than can be addressed using a single-phase design. In doing so, the power converter is optimized at a load current range that requires all phases to be operational. During periods of light loading, it may be beneficial to disable one or more phases to eliminate the current drain and switching losses associated with those phases, resulting in higher efficiency. The ZL9117M offers the ability to add and drop phases using a PMBus command in response to an observed load current change. All phases in a current share rail are considered active prior to the current sharing rail ramp to power-good. Any member of the current sharing rail can be dropped. If the reference module is dropped, the remaining active module with the lowest member position becomes the new reference. VREFERENCE -R VOUT The phase offset of (multi-phase) current sharing modules is automatically set to a value between 0° and 337.5° in 22.5° increments as in Equation 3: Additionally, any change to the number of members of a current sharing rail will precipitate autonomous phase distribution within the rail where all active phases realign their phase position based on their order within the number of active members. VMEMBER -R If the members of a current sharing rail are forced to shut down due to an observed fault, all members of the rail attempt to re-start simultaneously after the fault has cleared. I MEMBER I OUT Monitoring via I2C/SMBus I REFERENCE FIGURE 15. ACTIVE CURRENT SHARING Figure 15 shows that, for load lines with identical slopes, the member voltage is increased towards the reference voltage which closes the gap between the inductor currents. A system controller can monitor a wide variety of different ZL9117M system parameters through the I2C/SMBus interface. The module can monitor for any number of power conversion parameters including but not limited to the following: The relation between reference and member current and voltage is given by Equation 2: • Input voltage/Output voltage V MEMBER = V OUT + R × ( I REFERENCE – I MEMBER ) • Internal temperature where R is the value of the droop resistance. 12 (EQ. 2) • Output current • Switching frequency • Duty cycle FN7914.1 October 21, 2011 ZL9117M Please refer to Application Note AN2033 for details on how to monitor specific parameters via the I2C/SMBus interface. Snapshot Parameter Capture The ZL9117M offers a special feature that enables the user to capture parametric data during normal operation or following a fault. The SnapShot functionality is enabled by setting bit 1 of MISC_CONFIG to 1. See AN2033 for details on using SnapShot in addition to the parameters supported. The SnapShot feature enables the user to read parameters via a block read transfer through the SMBus. This can be done during normal operation, although it should be noted that reading the 22 bytes occupies the SMBus for some time. The SNAPSHOT_CONTROL command enables the user to store the SnapShot parameters to Flash memory in response to a pending fault, as well as to read the stored data from Flash memory after a fault has occurred. Table 3 describes the usage of this command. Automatic writes to Flash memory following a fault are triggered when any fault threshold level is exceeded, provided that the specific fault’s response is to shut down (writing to Flash memory is not allowed if the device is configured to re-try following the specific fault condition). It should also be noted that the module’s VDD voltage must be maintained during the time when the controller is writing the data to Flash memory; a process that requires between 700µs to 1400µs, depending on whether the data is set up for a block write. Undesirable results may be observed if the device’s VDD supply drops below 3.0V during this process. 2. User Store: The user can modify certain power supply settings as described in this data sheet. The user stores their configuration in the user store. Please refer to Application Note AN2033 for details on how to set specific security measures via the I2C/SMBus interface. Layout Guide To achieve stable operation, low losses, and good thermal performance some layout considerations are necessary. • Establish a continuous ground plane connecting SGND (pin 9), PGND (pin 10), and PGND (pin 16). • Place a high frequency ceramic capacitor between (1) VIN and PGND (pin 16), (2) VOUT and PGND (pin 16) and (3) bypass capacitors between VDRV, VDD, V25, VR and the ground plane, as close to the module as possible to minimize high frequency noise. High frequency ceramic capacitors close to the module between VOUT and PGND will help to minimize noise at the output ripple. • Use large copper areas for power path (VIN, PGND, VOUT) to minimize conduction loss and thermal stress. Also, use multiple vias to connect the power planes in different layers. • Connect remote sensed traces to the regulation point to achieve a tight output voltage regulation, and keep them in parallel. Route a trace from FB- to a location near the load ground, and a trace from FB+ to the point-of-load where the tight output voltage is desired. • Avoid routing any sensitive signal traces, such as the VOUT, FB+, FB- sensing point near the PHASE pin. TABLE 3. SNAPSHOT_CONTROL COMMAND CVR If the module experiences a fault and power is lost, the user can extract the last SnapShot parameters stored during the fault by writing a 1 to SNAPSHOT_CONTROL (transfers data from Flash memory to RAM) and then issuing a SNAPSHOT command (reads data from RAM via SMBus). SA S CL 6 5 4 3 2 SDA 21 VSET V25 11 20 VTRK VDD 12 19 FB+ VDRV 13 18 FB- SW 14 TO VOUT TO LOAD GND VOUT 17 VIN 15 PGND 16 Non-Volatile Memory and Device Security Features The ZL9117M has internal non-volatile memory where user configurations are stored. Integrated security measures ensure that the user can only restore the module to a level that has been made available to them. 7 1 9 CVDRV 8 10 PGND CV25 CVDD S Y NC Writes current SNAPSHOT values to Flash memory. Only available when device is disabled. PG 2 EN Copies current SNAPSHOT values from Flash memory to RAM for immediate access using SNAPSHOT command. VR DESCRIPTION 1 DDC SGN D DATA VALUE CIN COUT FIGURE 16. RECOMMENDED LAYOUT During the initialization process, the ZL9117M checks for stored values contained in its internal non-volatile memory. The ZL9117M offers two internal memory storage units that are accessible by the user as follows: 1. Default Store: The ZL9117M has a default configuration that is stored in the default store in the controller. The module can be restored to its default settings by issuing a RESTORE_DEFAULT_ALL command over the SMBus. 13 FN7914.1 October 21, 2011 ZL9117M Thermal Considerations Stencil Pattern Design Experimental power loss curves along with θJA from thermal modeling analysis can be used to evaluate the thermal consideration for the module. The derating curves are derived from the maximum power allowed while maintaining the temperature below the maximum junction temperature of +125°C. In actual application, other heat sources and design margin should be considered. Reflowed solder joints on the perimeter I/O lands should have about a 50µm to 75µm (2mil to 3mil) standoff height. The solder paste stencil design is the first step in developing optimized, reliable solder joins. Stencil aperture size to land size ratio should typically be 1:1. The aperture width may be reduced slightly to help prevent solder bridging between adjacent I/O lands. To reduce solder paste volume on the larger thermal lands, it is recommended that an array of smaller apertures be used instead of one large aperture. It is recommended that the stencil printing area cover 50% to 80% of the PCB layout pattern. A typical solder stencil pattern is shown on the second page of the Package Outline Drawing L21.15x15 on page 17. The gap width between pad to pad is 0.6mm. The user should consider the symmetry of the whole stencil pattern when designing its pads. A laser cut, stainless steel stencil with electropolished trapezoidal walls is recommended. Electropolishing “smooths” the aperture walls resulting in reduced surface friction and better paste release which reduces voids. Using a Trapezoidal Section Aperture (TSA) also promotes paste release and forms a "brick like" paste deposit that assists in firm component placement. A 0.1mm to 0.15mm stencil thickness is recommended for this large pitch (1.3mm) QFN. The structure of the ZL9117M belongs to the Quad Flat-pack No-lead package (QFN). This kind of package has advantages, such as good thermal and electrical conductivity, low weight and small size. The QFN package is applicable for surface mounting technology and is being more readily used in the industry. The ZL9117M contains several types of devices, including resistors, capacitors, inductors and control ICs. The ZL9117M is a copper lead-frame based package with exposed copper thermal pads, which have good electrical and thermal conductivity. The copper lead frame and multi component assembly is overmolded with polymer mold compound to protect these devices. The package outline and typical PCB layout pattern design and typical stencil pattern design are shown on the second page of the package outline drawing L21.15x15 on page 17. The module has a small size of 15mm x 15mm x 3.5mm. Figure 17 shows typical reflow profile parameters. These guidelines are general design rules. Users could modify parameters according to their application. PCB Layout Pattern Design The bottom of ZL9117M is a lead-frame footprint, which is attached to the PCB by surface mounting process. The PCB layout pattern is shown on the second page of the Package Outline Drawing L21.15x15 on page 17. The PCB layout pattern is essentially 1:1 with the QFN exposed pad and I/O termination dimensions, except for the PCB lands being a slightly extended distance of 0.2mm (0.4mm max) longer than the QFN terminations, which allows for solder filleting around the periphery of the package. This ensures a more complete and inspectable solder joint. The thermal lands on the PCB layout should match 1:1 with the package exposed die pads. Thermal Vias A grid of 1.0mm to 1.2mm pitch thermal vias, which drops down and connects to buried copper plane(s), should be placed under the thermal land. The vias should be about 0.3mm to 0.33mm in diameter with the barrel plated to about 1.0 ounce copper. Although adding more vias (by decreasing via pitch) will improve the thermal performance, diminishing returns will be seen as more and more vias are added. Simply use as many vias as practical for the thermal land size and your board design rules allow. 14 Reflow Parameters Due to the low mount height of the QFN, "No Clean" Type 3 solder paste per ANSI/J-STD-005 is recommended. Nitrogen purge is also recommended during reflow. A system board reflow profile depends on the thermal mass of the entire populated board, so it is not practical to define a specific soldering profile just for the QFN. The profile given in Figure 17 is provided as a guideline, to be customized for varying manufacturing practices and applications. 300 PEAK TEMPERATURE ~+245°C; TYPICALLY 60s-150s ABOVE +217°C KEEP LESS THAN 30s WITHIN 5°C OF PEAK TEMP. 250 TEMPERATURE (°C) Package Description 200 SLOW RAMP (3°C/s MAX) AND SOAK FROM +150°C TO +200°C FOR 60s~180s 150 100 RAMP RATE ≤1.5°C FROM +70°C TO +90°C 50 0 0 100 150 200 250 300 350 DURATION (s) FIGURE 17. TYPICAL REFLOW PROFILE FN7914.1 October 21, 2011 ZL9117M Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make sure you have the latest revision. DATE REVISION October 12, 2011 FN7914.1 CHANGE On page 1: Changed ".. required for a complete DC/DC power solution." in first paragraph to ".. required for a highly integrated DC/DC power solution.” Added "This power module has built-in auto-compensation algorithms, which eliminates the need for manual compensation design work." to first paragraph. Changed "The ZL9117M features internal compensation.." to "The ZL9117M features auto-compensation.." Added "Auto Compensating PID Filter" to “Features”. August 30, 2011 FN7914.0 Initial Release Products Intersil Corporation is a leader in the design and manufacture of high-performance analog semiconductors. The Company's products address some of the industry's fastest growing markets, such as, flat panel displays, cell phones, handheld products, and notebooks. Intersil's product families address power management and analog signal processing functions. Go to www.intersil.com/products for a complete list of Intersil product families. For a complete listing of Applications, Related Documentation and Related Parts, please see the respective device information page on intersil.com: ZL9117M To report errors or suggestions for this datasheet, please go to www.intersil.com/askourstaff FITs are available from our website at http://rel.intersil.com/reports/search.php For additional products, see www.intersil.com/product_tree Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 15 FN7914.1 October 21, 2011 Package Outline Drawing L21.15x15 21 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE (PUNCH QFN) Rev 2, 8/11 X4 0.2 S AB 16x 0.80 16 7.25 18 2 3 4 5 6 7 8 8.30 1.25 4.20 16 16 14 0.80 9 15 1.95 13 12 11 10 4.65 5.65 33x 0.50 2.95 13 14 15 1 x 0.76 15.0±0.2 15.8±0.2 B 0.05 8x 1.80±0.05 TOP VIEW S AB BOTTOM VIEW A S 0.2 S SIDE VIEW 18 17 16 A A A 19 20 21 1 2 3 4 5 6 7 8 14 FN7914.1 October 21, 2011 0.50 S 0.05 B ND A A A A A A A A AROU 3.5±0.2 5° ALL B 9 15 B A A A A A A A A A 13 A A A B 12 11 10 C C B A:1.3±0.1 B:2.6±0.1 C:1.13±0.1 ZL9117M 9 10 11 12 19 20 21 1 3.10 12.05 15.8±0.2 15.0±0.2 17 4.40 2 3 4 5 6 7 8 2.95 18 17 6.25 1.95 1 21 20 19 17x 0.75 9x 1.90±0.05 A 6.90 6.30 5.60 5.00 4.30 3.70 3.00 2.40 0.55 0 0.05 0.90 1.50 2.20 2.80 3.50 4.10 6.78 8.20 6.90 8.30 0.15 0.65 4.20 7.00 6.20 5.70 4.90 4.40 3.60 3.10 2.30 0.65 0 6.00 5.60 4.80 8.30 4.30 6.90 3.50 3.00 5.60 1 2 2.20 4.95 4.15 1.05 0.25 0 0.40 0.90 1.70 2.20 4.150 4.95 5.60 3.00 4.80 8.30 4.20 3.60 2.90 1 2 2.30 1.60 1.00 0.30 0 0.30 1.00 1.60 2.30 2.90 4.90 5.50 6.10 8.30 0.15 0.65 1.45 2.25 4.85 5.65 6.90 Unit: mm Tolerance: ±0.01mm Unit: mm Tolerance: ±0.01mm STENCIL PATTERN WITH SQUARE PADS-1 6.48 3.42 4.02 0 0.95 TYPICAL RECOMMENDED LAND PATTERN 6.37 5.25 3.85 1 2 1.35 0.75 0 0.05 1.65 2.25 3.85 5.25 6.375 0 1.25 1.85 3.85 4.45 5.80 NOTES: 1. Dimensions are in millimeters. 2. Unless otherwise specified, tolerance : Decimal ± 0.2; Body Tolerance ±0.2mm 3. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 indentifier may be either a mold or mark feature. Unit: mm Tolerance: ±0.01mm 0 0.75 2.45 2.55 3.05 4.215 4.55 4.815 5.80 6.33 6.475 FN7914.1 October 21, 2011 STENCIL PATTERN WITH SQUARE PADS-2 STENCIL PATTERN WITH SQUARE PADS-2 ZL9117M 8.30 6.10 5.50 4.70 4.205 3.445 2.95 2.15 0.65 0 5.60 6.00 8.20 6.82 5.50 5.05 4.05 3.60 2.90 2.30 1.60 1.15 0.15 0 0.30 1.00 1.60 2.30 2.90 3.60 4.05 5.05 5.50 6.82 8.20 6.20 5.40 4.80 4.105 3.545 2.85 2.25 0.55 0 0.75 1.35 2.35 2.80 3.50 4.10 6.10 6.70 8.20 17 1.70 0.90 0.40 0 6.10 5.50 4.90