He xa gon Applic atio n Ki t For XMC4000 Family H MI_ O LE D - V1 Standard Human Machine Interface Card Boa rd Us er„s Ma nu al Revision 1.0, 2012-02-28 Mic rocon t rolle r Edition 2012-02-28 Published by Infineon Technologies AG 81726 Munich, Germany © 2012 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. HMI_OLED-V1 Standard Human Machine Interface Card Revision History Page or Item Subjects (major changes since previous revision) Revision 1.0, 2012-02-28 Initial release Trademarks of Infineon Technologies AG AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, EconoPACK™, CoolMOS™, CoolSET™, CORECONTROL™, CROSSAVE™, DAVE™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, HITFET™, HybridPACK™, I²RF™, ISOFACE™, IsoPACK™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OptiMOS™, ORIGA™, PRIMARION™, PrimePACK™, PrimeSTACK™, PRO-SIL™, PROFET™, RASIC™, ReverSave™, SatRIC™, SIEGET™, SINDRION™, SIPMOS™, SmartLEWIS™, SOLID FLASH™, TEMPFET™, thinQ!™, TRENCHSTOP™, TriCore™. Other Trademarks Advance Design System™ (ADS) of Agilent Technologies, AMBA™, ARM™, MULTI-ICE™, KEIL™, PRIMECELL™, REALVIEW™, THUMB™, µVision™ of ARM Limited, UK. AUTOSAR™ is licensed by AUTOSAR development partnership. Bluetooth™ of Bluetooth SIG Inc. CAT-iq™ of DECT Forum. COLOSSUS™, FirstGPS™ of Trimble Navigation Ltd. EMV™ of EMVCo, LLC (Visa Holdings Inc.). EPCOS™ of Epcos AG. FLEXGO™ of Microsoft Corporation. FlexRay™ is licensed by FlexRay Consortium. HYPERTERMINAL™ of Hilgraeve Incorporated. IEC™ of Commission Electrotechnique Internationale. IrDA™ of Infrared Data Association Corporation. ISO™ of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB™ of MathWorks, Inc. MAXIM™ of Maxim Integrated Products, Inc. MICROTEC™, NUCLEUS™ of Mentor Graphics Corporation. Mifare™ of NXP. MIPI™ of MIPI Alliance, Inc. MIPS™ of MIPS Technologies, Inc., USA. muRata™ of MURATA MANUFACTURING CO., MICROWAVE OFFICE™ (MWO) of Applied Wave Research Inc., OmniVision™ of OmniVision Technologies, Inc. Openwave™ Openwave Systems Inc. RED HAT™ Red Hat, Inc. RFMD™ RF Micro Devices, Inc. SIRIUS™ of Sirius Satellite Radio Inc. SOLARIS™ of Sun Microsystems, Inc. SPANSION™ of Spansion LLC Ltd. Symbian™ of Symbian Software Limited. TAIYO YUDEN™ of Taiyo Yuden Co. TEAKLITE™ of CEVA, Inc. TEKTRONIX™ of Tektronix Inc. TOKO™ of TOKO KABUSHIKI KAISHA TA. UNIX™ of X/Open Company Limited. VERILOG™, PALLADIUM™ of Cadence Design Systems, Inc. VLYNQ™ of Texas Instruments Incorporated. VXWORKS™, WIND RIVER™ of WIND RIVER SYSTEMS, INC. ZETEX™ of Diodes Zetex Limited. Last Trademarks Update 2011-02-24 Template: IFX_Template_2011-02-24.dot HMI_OLED-V1 Standard Human Machine Interface Card Table of Contents Table of Contents 1 1.1 1.2 Overview ............................................................................................................................................. 7 Key Features ........................................................................................................................................ 7 Block Diagram ...................................................................................................................................... 8 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Hardware Description ........................................................................................................................ 9 MicroSD Memory Slot ........................................................................................................................ 10 OLED Display ..................................................................................................................................... 11 Audio .................................................................................................................................................. 12 IO Expander ....................................................................................................................................... 13 Touch Buttons .................................................................................................................................... 14 Power ................................................................................................................................................. 14 Satellite Connector ............................................................................................................................. 15 3 3.1 3.2 3.3 Production Data................................................................................................................................ 17 Schematics ......................................................................................................................................... 17 Layout and Geometry ......................................................................................................................... 20 Bill of Material ..................................................................................................................................... 21 Board Users Manual 4 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card List of Figures List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Block Diagram of Standard Human Machine Interface Card ............................................................... 8 Standard HMI Card Interfaces ............................................................................................................. 9 MicroSD card Connector Intertface .................................................................................................... 10 Touch Buttons .................................................................................................................................... 14 Power Circuit ...................................................................................................................................... 15 HMI Satellite Connector ..................................................................................................................... 15 Satellite Connector HMI ..................................................................................................................... 16 Satellite Connector, Power, Touch button ......................................................................................... 18 Micro-SD, Audio, IO Expander, OLED ............................................................................................... 19 Standard Human Machine Interface Card Layout .............................................................................. 20 Board Users Manual 5 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card List of Tables List of Tables Table 1 Table 2 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 MicroSD Connector ............................................................................................................................ 10 MicroSD signal connection to the Satellite Connector ....................................................................... 11 OLED display Connector Pinout ........................................................................................................ 11 OLED signal connection to the Satellite Connector ........................................................................... 12 2.5 mm Audio Jack Pinout ................................................................................................................. 13 Audio signal connection to the Satellite Connector ............................................................................ 13 GPIO channel LED/SMD pad mapping .............................................................................................. 13 IO Expander I2C signal connection to the Satellite Connector .......................................................... 13 Touch signal connection to the Satellite Connector ........................................................................... 14 Power LED ......................................................................................................................................... 14 Power rail connection to the Satellite Connector ............................................................................... 15 Standard Human Machine Interface Card BOM ................................................................................ 21 Board Users Manual 6 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Overview Introduction This document describes the features and hardware details of the Standard Human Machine Interface Card (HMI_OLED-V1) designed to work with Infineon‟s XMC4500 CPU board. This board is part of Infineon‟s Hexagon Application Kits. 1 Overview The HMI_OLED-V1 board is an application expansion satellite card of Hexagon Application Kits. The satellite card along with a CPU board (e.g. CPU_45A-V2 board) demonstrates the Human Machine Interface (HMI) capabilities of XMC4500. The main use case for this satellite card is to demonstrate the HMI features of XMC4500 device including the toolchain. The focus is safe operation under evaluation conditions. The board is not cost optimized and cannot be seen as reference design. 1.1 Key Features The HMI_OLED-V1 satellite card is equipped with following features Connection to CPU board (e.g. CPU_45A-V2) via HMI satellite connector Micro SD card connector – 4 bit mode Passive matrix OLED display (PMOLED), 1.54” screen size, 160x128 pixels Stereo audio codec TLV320AIC3204 2.5 mm stereo receptacle for audio headsets with microphone 2 touch buttons with LED‟s I2C based IO expander with 8 channels Power supply via satellite connector Board Users Manual 7 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Overview 1.2 Block Diagram Figure 1 shows the block diagram of the HMI_OLED-V1 satetllite card. There are following building blocks: Micro-SD Connector Standard Human Machine Interface Card HMI_OLED-V1 SD/MMC LED/TS I2S HMI Satellite Connector Figure 1 I2C Touch Button (2) / LEDs (2) Audio Codec (TLV320AIC3204) I2C GPIO Expander (PCA9502) SPI PMOLED Display (DD-160128FC-1A) Audio Jack (2.5 mm) GPIO/LEDs (8) Block Diagram of Standard Human Machine Interface Card Board Users Manual 8 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description 2 Hardware Description The following sections give a detailed description of the hardware and how it can be used. HMI Satellite Connector Power LEDs Power 3.3 V LDO OLED Display Micro SD Card Connector OLED Backlight Supply Audio Codec Audio Jack Touch Button Touch Button GPIO Expander and LEDs Figure 2 Standard HMI Card Interfaces Board Users Manual 9 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description 2.1 MicroSD Memory Slot The HMI_OLED-V1 satetllite card supports a MicroSD card connector on board. The SD/MMC interface of XMC4500 can be used in different modes (SPI mode, 1-bit SD, 4-bit SD, 8-bit MMC). HMI_OLED-V1 satetllite card supports 4-bit SD mode implementation of SD card interface. Note: Signals MMC_BUSPWR and MMC_LED from SD card are connected to ground in CPU board CPU_45AV2, hence power a SD-Card will be always enabled and LED (V300) will be ON when satellite card is powered and interfaced to CPU_45A-V2 board . Figure 3 MicroSD card Connector Intertface Table 1 below gives the signal details of SD card connector interface. Table 1 MicroSD Connector Pin No. Signal Name Description 1 DAT2 Data Bit 2 2 DAT3/CS_N Data Bit 3 3 CMD/MOSI Command 4 VDD Power (+3.3 V) 5 CLK/SCK Clock 6 GND Ground 7 DAT0 Data Bit 0 8 DAT1 Data Bit 1 Board Users Manual 10 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description Table 2 shows the connection of the MicroSD card signals to the HMI satellite connector. Table 2 MicroSD signal connection to the Satellite Connector Pin No. Signal Name Description 3 MMC_CLK Clock 6 MMC_DATA0 Data Bit 0 5 MMC_DATA1 Data Bit 1 8 MMC_DATA2 Data Bit 2 7 MMC_DATA3 Data Bit 3 13 MMC_BUSPWR Power 14 MMC_CMD Command 16 MMC_LED LED 2.2 OLED Display The HMI_OLED-V1 satellite card supports a passive matrix OLED display (PMOLED) from Densitron on board. The display DD-160128FC-1A has a resolution of 160x128 pixels on a 1.54” screen. The card implements PMOLED display interface through SPI-Bus of XMC4500. This display module uses a Syncoam SEPS525F 160 RGB x 128 Dots, 262K Colors PMOLED Display Driver and Controller. Refer to the SEPS525F datasheet for details. The card implements a backlight power supply STOD2540 to generate 13 Volt (VDD13). LED V241 indicates the presence of VDD13 (OLED Backlight Supply) Table 3 gives the details of OLED display connector pin mapping. Table 3 OLED display Connector Pinout Pin No. Signal Name Description 1 NC No Connect 2 VSDH Data Driver Ground 3 VDDH Data, Scan Driver Power Supply (8 ~ 18 V) 4 VSSH Scan Driver Ground 5 IREF Tie 70 ㏀ to VSS 6 OSCA2 Tie 10 ㏀ to OSCA1 between OSCA2 7 OSCA1 Tie 10 ㏀ to OSCA1 between OSCA2 8 VDDIO MPU I/F PAD Power Supply (1.6 ~ 3.3 V) 9 VSYNCO No Connect (used only in RGB mode) 10 VSYNC No Connect (used only in RGB mode) 11 HSYNC No Connect (used only in RGB mode) 12 DOTCLK No Connect (used only in RGB mode) 13 ENABLE No Connect (used only in RGB mode) CPU Selects the CPU type Low : 80 Series CPU, High : 68 Series CPU 14 15 PS Selects Parallel/Serial Interface For SPI, connect Low 16 D17/SCL SPI Clock 17 D16/SDI SPI Data Input Board Users Manual 11 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description Table 3 OLED display Connector Pinout Pin No. Signal Name Description 18 D15/SDO SPI Data Output (use 0 ohm) 19 D14 No Connect (used only in parallel mode) 20 D13 No Connect (used only in parallel mode) 21 D12 No Connect (used only in parallel mode) 22 D11 No Connect (used only in parallel mode) 23 D10 No Connect (used only in parallel mode) 24 D9 No Connect (used only in parallel mode) 25 RS Data/Command Select 26 CSB SPI Select 27 RDB When using SPI, fix it to VDD or VSS level 28 WRB When using SPI, fix it to VDD or VSS level 29 RESETB Reset SEPS525(active low) 30 VSS Logic Ground 31 VDD Logic Power Supply(2.4 ~ 3.3 V) 32 VSSH Scan Driver Ground 33 VDDH Data, Scan Driver Power Supply(8 ~ 18 V) 34 VSDH Data Driver Ground 35 NC No connect The PMOLED display module is interfaced to the connector through a 30-wire flatcable and glued to the satellite card. Table 4 shows the connection of the OLED signals to the HMI satellite connector. Table 4 OLED signal connection to the Satellite Connector Pin No. Signal Name Description 31 SPI_CSH0 Chipselect 32 SPI_MTSR Data In 34 SPI_MRST Data Out 36 SPI_CLK Clock 24 OLED_RS Data/Command Select 42 RESET_N Reset 2.3 Audio The HMI_OLED-V1 satetllite card supports audio interface on board with stereo audio codec TLV320AIC3204 (U320). The control interface of audio codec is through I2C Bus and audio data is interfaced to I2S Bus of XMC4500 CPU extended though satellite connector. A GPIO pin (P2.10) is used to reset the the audio codec (signal AUDIO_RST_N). The codec has a built-in headphone driver as well as a microphone input (analog and digital). The satellite card uses a 4-pin, 2.5 mm stereo receptacle (Nokia 6300 style) for audio headsets. The board supports an external clock through an oscillator (Q320). Currently this oscillator is not mounted. Board Users Manual 12 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description Table 5 2.5 mm Audio Jack Pinout Pin No. Signal Name Description 1 GND Ground 2 HPL Head Phone Left 3 HPR Head Phone Right 4 MICBIAS Mic Input Table 6 shows the connection of the audio signals to the HMI satellite connector. Table 6 Audio signal connection to the Satellite Connector Pin No. Signal Name Description 23 AUDIO_RST_N Reset 25 I2S_WA Address 27 I2S_MCLK Master Clock 26 I2S_MTSR Data In 28 I2S_MRST Data Out 30 I2S_SCLK Slave Clock 2.4 IO Expander The HMI_OLED-V1 satellite card supports GPIO expansion though I2C IO-Expander on board (U360). The I2C address for the IO expander device is 0x1001101X. The satellite card supports 8 such GPIO‟s. All the GPIO‟s are connected to LEDs (V360-V367) and SMD-Pads (TP360 – TP367). The Table 7 shows the GPIO channel and corresponding LED/PAD mapping. Table 7 GPIO channel LED/SMD pad mapping GPIO LED Reference SMD pad Reference GPIO0 V360 TP360 GPIO1 V361 TP361 GPIO2 V362 TP362 GPIO3 V363 TP363 GPIO4 V364 TP364 GPIO5 V365 TP365 GPIO6 V366 TP366 GPIO7 V367 TP367 Table 8 shows the connection of the IO Expander device to the HMI satellite connector. Table 8 IO Expander I2C signal connection to the Satellite Connector Pin No. Signal Name Description 38 I2C_SCL Clock 37 I2C_SDA Data Board Users Manual 13 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description 2.5 Touch Buttons The HMI_OLED-V1 satellite card supports two touch buttons (TOUCH250 and TOUCH251) that are connected to the CPU board via the satellite connector. These two signals are connected to LED‟s V250 & V251. Figure 4 Touch Buttons Table 9 shows the connection of the touch signals to the HMI satellite connector. Table 9 Touch signal connection to the Satellite Connector Pin No. Signal Name Description 75 LEDTS_COL0 Column 0 77 LEDTS_COLA Column A 74 TP2 Touch 2 64 TP7 Touch 7 2.6 Power Power input (5 V) to the satellite card is supported through satellite connector. 3.3 V is generated on board using on board regulator (U220). LED V240 indicates the presence of 3.3 V power. The card implements a backlight power supply STOD2540 to generate 13 Volt (VDD13). LED V241 indicates the presence of VDD13 (OLED Backlight Supply) Table 10 Power LED LED Power Rail Voltage Note V240 VDD3.3 3.3 V Must always be “ON” V241 VDD13 13 V Must always be “ON” Board Users Manual 14 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description HMI Sat. Connector VDD3.3 VDD13 VDD5 +13 V U230 OLED Display VDD13 Back Light Supply STOD2540 +3.3 V U220 Lin. Voltage Regulator IFX1763 VDD3.3 On board devices VDD5 Human Machine Interface Card HMI_OLED-V1 Figure 5 Power Circuit Table 11 shows the connection of the power rails to the HMI satellite connector. Table 11 Power rail connection to the Satellite Connector Pin No. Power rail Description 43,44,45,46 VDD5 5V 1,2,79,80 GND Ground 2.7 Satellite Connector The satellite connector of the HMI_OLED-V1 satellite card interfaces it‟s the signals to a CPU board e.g. CPU_45A-V2. Take care to connect the HMI satellite card always to the corresponding HMI satellite connector of the CPU board only. Figure 6 HMI Satellite Connector Board Users Manual 15 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Hardware Description The Signals mapping details of HMI satellite connector and correponding CPU function are provided in Figure 7. Figure 7 Satellite Connector HMI Board Users Manual 16 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data 3 Production Data 3.1 Schematics This chapter contains the schematics for the Standard Human Machine Interface Card: Satellite Connector, Power, Touch button Micro-SD, Audio, IO Expander, OLED Board Users Manual 17 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data Figure 8 Satellite Connector, Power, Touch button Board Users Manual 18 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data Figure 9 Micro-SD, Audio, IO Expander, OLED Board Users Manual 19 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data 3.2 Figure 10 Layout and Geometry Standard Human Machine Interface Card Layout Board Users Manual 20 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data 3.3 Bill of Material Table 12 Standard Human Machine Interface Card BOM Sl. No. Qty Value Device Reference Designator 1 2 0R/0603 Resistor R224, R323 2 1 1k5/0603 Resistor R360 3 11 2k2/0603 Resistor 4 1 4*10k/S1206 Resistor R252, R253, R322, R361, R362, R363, R364, R365, R366, R367, R368 RA300 5 1 5k6/0603 Resistor R241 6 8 10k/0603 Resistor 7 8 10uF/10V/0805 Capacitor 8 1 10uF/35V/1206 Capacitor R235, R300, R302, R320, R341, R342, R343, R345 C220, C222, C230, C324, C326, C328, C329, C330 C231 9 1 22R/0603 Resistor R321 10 2 47uF/TA/6V3 Capacitor C322, C323 11 1 56k/0603 Resistor R233 12 1 68k/0603 Resistor R340 13 1 100k/0603 Resistor R234 14 12 100nF/0603 Capacitor C200, C202, C223, C300, C320, C325, C327, C340, C341, C342, C343, C360 15 1 470nF/1206 Capacitor C321 16 2 680R/0603 Resistor R240, R301 17 1 54132-3562 Connector 54132-3562 Molex X340 Connector 3M 290805WB-MG or Molex 047334001 Diode B340A-13-F Diodes Inc. IC BSS209PW Infineon technologies Connector HSEC8-140-01S-RA Samtec 18 1 473340001 19 1 B340A-13-F 20 1 BSS209PW 21 1 HSEC8-140-01-SRA 22 1 IFX1763SJV33 23 8 LED-GE/D/0603 24 3 LED-GN/D/0603 IC IFX1763SJV33 Infineon U220 Technologies V360, V361, V362, V363, V364, V365, V366, LED V367 LED V240, V241, V300 25 2 LED-RT/D/0603 LED 26 1 PCA9502 27 1 SJ1-42514-SMT 28 1 STOD2540 Board Users Manual X300 V230 Q300 X200 V250, V251 IC PCA9502BS NXP, HVQFN-24 Connector SJ1-42514SMT IC STOD2540PUR STMicro 21 U360 X320 U230 Revision 1.0, 2012-02-28 HMI_OLED-V1 Standard Human Machine Interface Card Production Data Table 12 Standard Human Machine Interface Card BOM Reference Designator Sl. No. Qty Value 29 1 TLV320AIC3204 30 1 VLS3015ET-4R7M 31 1 no ass. 32 3 no ass./0R/0603 IC TLV320AIC3204 Texas Instruments Inductor VLS3015ET4R7M TDK Crystal 3.3V 7x5mm SMD Resistor 33 2 no ass./2k2/0603 Resistor R210, R211 34 2 no ass./10k/0603 Resistor R250, R251 35 1 no ass./10nF/0603 Capacitor C221 36 2 no ass. Touchpad TOUCH250, TOUCH251 SMD-Pads TP200, TP240, TP241, TP242, TP360, TP361, TP362, TP363, TP364, TP365, TP366, TP367 37 12 no ass. Board Users Manual Device 22 U320 L230 Q320 R223, R232, R344 Revision 1.0, 2012-02-28 w w w . i n f i n e o n . c o m Published by Infineon Technologies AG