Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents Interference Suppression Film Capacitors - Class X2 Radial MKP 310 VAC - Standard Across the Line FEATURES • 10 mm to 27.5 mm lead pitch • Supplied loose in box, taped on reel • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS For standard across the line X2 applications See also application note: www.vishay.com/doc?28153 QUICK REFERENCE DATA Capacitance range (E12 series) 0.001 μF to 2.2 μF (preferred values acc. to E6) Capacitance tolerance ± 20 %; ± 10 %; ± 5 % Climatic testing class according to IEC 60068-1 55/110/56/B Rated AC voltage 310 VAC; 50 Hz to 60 Hz Permissible DC voltage 800 VDC at 85 °C, 630 VDC at 110 °C C 470 nF: 110 °C (125 °C for less than 1000 h), C > 470 nF: 110 °C Maximum application temperature IEC 60384-14 and EN60384-14 IEC 60065, pass. flamm. class B for volumes > 1750 mm3 CQC UL 60384-14; CSA E384-14 Reference standards Dielectric Polypropylene film Electrodes Metallized film Mono construction Construction Encapsulation Plastic case, epoxy resin sealed, flame retardant UL-class 94 V-0 Leads Tinned wire C-value; tolerance; rated voltage; sub-class; manufacturer’s type designation; code for dielectric material; manufacturer location; manufacturer’s logo; year and week; safety approvals Marking Note • For more detailed data and test requirements, contact: [email protected] DIMENSIONS in millimeters l w h lt P ± 0.4 Revision: 23-Feb-16 Ø dt Document Number: 28120 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents COMPOSITION OF CATALOG NUMBER TYPE AND PITCHES MULTIPLIER (nF) CAPACITANCE 10.0 mm (numerically) 336 2 15.0 mm 0.1 X2 22.5 mm 1 3 10 4 100 5 27.5 mm Example: 104 = 10 x 10 = 100 nF BFC2 336 2222(*) 336 2X 2X 2 XX X XX X (*) old ordering code TYPE PACKAGING STANDARD DIMENSIONS C-TOL. Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm Loose in box Taped on reel Lead length 5.0 mm ± 1.0 mm (1) Loose in box Taped on reel Loose in box ± 20 % H = 18.5 mm; P0 = 12.7 mm BFC2 336 23… Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm BFC2 336 21… ± 10 % Taped on reel PACKAGING See tables L ea d l en gth 25. 0 mm ± 2.0 mm B FC 2 33 6 27 … H = 18.5 mm; P0 = 12.7 mm BFC2 336 24… Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm BFC2 336 22… ±5% L ead le ngt h 2 5.0 mm ± 2 .0 mm (1) See tables BFC2 336 26… L ead length 5.0 mm ± 1.0 mm 336 2 X2 BFC2 336 20… Lead length 25.0 mm ± 2.0 mm L e a d l e n g th 5 . 0 m m ± 1. 0 m m (1) CODE NUMBER B FC 2 33 6 28… H = 18.5 mm; P0 = 12.7 mm ALTERNATIVE LARGER PITCH SIZES See tables BFC2 336 25… C-TOL. CODE NUMBER Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm Loose in box Lead length 5.0 mm ± 1.0 mm ± 20 % Lead length 25.0 mm ± 2.0 mm Taped on reel (1) H = 18.5 mm; P0 = 12.7 mm See tables for details Lead length 3.5 mm + 1 mm/- 0.5 mm or 3.5 mm ± 0.3 mm Loose in box Lead length 5.0 mm ± 1.0 mm ± 10 % Lead length 25.0 mm ± 2.0 mm Taped on reel (1)(2) H = 18.5 mm P0 = 12.7 mm Notes (1) For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 (2) Taped on reel pitch = 27.5 mm is not available Revision: 23-Feb-16 Document Number: 28120 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents SPECIFIC REFERENCE DATA DESCRIPTION VALUE 310 V Rated AC voltage URAC 630 V Permissible DC voltage URDC Tangent of loss angle: at 1 kHz at 10 kHz C < 470 nF 10 x 10-4 470 nF C 1 μF 20 x 10-4 C > 1 μF 30 x 10-4 20 x 10-4 70 x 10-4 - Rated voltage pulse slope (dU/dt)R at 435 VDC - Pitch = 10 mm 600 V/μs Pitch = 15 mm and 7.5 mm (bent back) 400 V/μs Pitch = 22.5 mm 150 V/μs Pitch = 27.5 mm 100 V/μs R between leads, for C 0.33 μF at 100 V; 1 min > 15 000 M RC between leads, for C > 0.33 μF at 100 V; 1 min > 5000 s R between leads and case; 100 V; 1 min > 30 000 M Withstanding (DC) voltage (cut off current 10 mA) (1); rise time 1000 V/s: C 1 μF 2200 V; 1 min C > 1 μF 1800 V; 1 min Withstanding (AC) voltage between leads and case 2120 V; 1 min Max. application temperature for 0.001 μF C 0.47 μF 110 °C (125 °C for less than 1000 h) Max. application temperature for C > 0.47 μF 110 °C Note (1) See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169 ELECTRICAL DATA AND ORDERING CODE - PITCH 10 mm CATALOG NUMBER BFC2 336 ..... AND PACKAGING URAC (V) DIMENSIONS wxhxl (mm) CAP. (μF) REEL (500 mm) (1)(2) LOOSE IN BOX MASS (g) (3) SHORT LEADS lt = 3.5 mm + 1 mm/- 0.5 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm H = 18.5 mm P0 = 12.7 mm SPQ SPQ PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 20 % 0.0010 20102 29131 26102 0.0015 20152 29132 26152 0.0022 20222 29133 26222 23222 0.0033 20332 29134 26332 23332 20472 29135 26472 23472 20682 29136 26682 0.010 20103 29137 26103 0.015 20153 29138 26153 0.022 20223 29139 26223 0.033 20333 29141 0.0047 0.0068 310 4.0 x 10.0 x 12.5 0.6 1000 750 26333 23102 1250 1000 23152 23682 23103 1400 1100 23153 23223 750 23333 900 PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 10 % 0.0010 21102 29154 27102 24102 0.0012 21122 - 27122 24122 0.0015 21152 29155 0.0018 4.0 x 10.0 x 12.5 21182 - 27182 24182 0.0022 21222 29156 27222 24222 Revision: 23-Feb-16 0.6 1000 27152 1250 24152 1400 Document Number: 28120 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING CODE - PITCH 10 mm CATALOG NUMBER BFC2 336 ..... AND PACKAGING URAC (V) DIMENSIONS wxhxl (mm) CAP. (μF) REEL (500 mm) (1)(2) LOOSE IN BOX MASS (g) (3) SHORT LEADS lt = 3.5 mm + 1 mm/- 0.5 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm H = 18.5 mm P0 = 12.7 mm SPQ SPQ PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 10 % 0.0027 21272 - 27272 24272 0.0033 21332 29157 27332 24332 0.0039 21392 - 27392 24392 0.0047 21472 29158 27472 24472 0.0056 21562 - 27562 24562 0.0068 21682 29159 27682 24682 21822 - 21103 29161 0.0082 0.010 4.0 x 10.0 x 12.5 0.6 1000 27822 1000 27103 24822 24103 0.012 21123 - 27123 24123 0.015 21153 29162 27153 24153 0.018 21183 - 27183 24183 0.022 21223 29163 27223 24223 0.027 21273 - 0.033 21333 29164 750 1100 27273 750 27333 24273 24333 900 PITCH = 10.0 mm ± 0.4 mm; dt = 0.6 mm ± 0.06 mm; C-TOL. = ± 5 % 310 0.0010 22102 - 28102 0.0012 22122 - 28122 0.0015 22152 - 28152 0.0018 22182 - 28182 0.0022 22222 - 28222 25222 0.0027 22272 - 28272 25272 0.0033 22332 - 28332 25332 0.0039 22392 - 28392 25392 0.0047 22472 - 28472 25472 25562 0.0056 1000 25102 25122 1250 25152 22562 - 28562 0.0068 22682 - 28682 0.0082 22822 - 28822 0.010 22103 - 28103 25103 0.012 22123 - 28123 25123 0.015 22153 - 28153 25153 0.018 22183 - 28183 25183 0.022 22223 - 28223 25223 0.027 22273 - 0.033 22333 - 4.0 x 10.0 x 12.5 0.6 750 28273 28333 1400 25182 1000 750 25682 25822 25273 25333 1100 900 Notes • SPQ = Standard Packing Quantity (1) H = In-tape height; P = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139 0 (2) Reel diameter = 356 mm is available on request (3) Weight for short lead product only Revision: 23-Feb-16 Document Number: 28120 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING CODE - PITCH 15 mm CATALOG NUMBER BFC2 336 ..... AND PACKAGING REEL (500 mm) (1)(2) LOOSE IN BOX URAC (V) CAP. (μF) 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 310 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.22 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.10 0.12 0.15 0.18 DIMENSIONS wxhxl (mm) 5.0 x 11.0 x 17.5 6.0 x 12.0 x 17.5 7.0 x 13.5 x 17.5 5.0 x 11.0 x 17.5 6.0 x 12.0 x 17.5 7.0 x 13.5 x 17.5 5.0 x 11.0 x 17.5 6.0 x 12.0 x 17.5 7.0 x 13.5 x 17.5 MASS (g) (3) SHORT LEADS LONG LEADS lt = 3.5 mm lt = 5.0 mm lt = 25.0 mm SPQ SPQ ± 0.3 mm ± 1.0 mm ± 2.0 mm PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 20 % 29001 29273 29097 29011 29274 29071 29021 29275 29076 0.98 29031 29276 29082 1000 1000 20473 29142 26473 20683 29143 26683 20104 29144 26104 1.4 20154 29145 26154 500 PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 20 % 1.8 20224 29146 500 26224 500 PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 10 % 29002 29281 29066 29007 29068 29012 29282 29072 29017 29074 29022 29283 29077 29027 29079 1000 0.98 29032 29284 29083 1000 21393 27393 21473 29165 27473 21563 27563 21683 29166 27683 21823 27823 21104 29167 27104 21124 27124 500 1.4 21154 29168 27154 PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 10 % 21184 27184 1.8 500 500 21224 29169 27224 PITCH = 15 mm ± 0.4 mm; dt = 0.60 ± 0.06 mm; C-TOL. = ± 5 % 29003 29067 29008 29069 29013 29073 29018 29075 29023 29078 29028 29081 1000 0.98 29033 29084 1000 22393 28393 22473 28473 22563 28563 22683 28683 22823 28823 22104 28104 22124 28124 500 1.4 22154 28154 PITCH = 15 mm ± 0.4 mm; dt = 0.80 ± 0.08 mm; C-TOL. = ± 5 % 1.8 22184 500 28184 500 H = 18.5 mm P0 = 12.7 mm SPQ 29004 29014 29024 29034 23473 23683 23104 23154 23224 29005 29009 29015 29019 29025 29029 29035 24393 24473 24563 24683 24823 24104 24124 24154 24184 24224 29006 29061 29016 29062 29026 29063 29036 25393 25473 25563 25683 25823 25104 25124 25154 25184 1100 900 650 600 1100 900 800 650 600 1100 900 800 650 600 Notes • SPQ = Standard Packing Quantity (1) H = In-tape height; P = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139 0 (2) Reel diameter = 356 mm is available on request (3) Weight for short lead product only Revision: 23-Feb-16 Document Number: 28120 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING CODE - PITCH 22.5 mm CATALOG NUMBER BFC2 336 ..... AND PACKAGING REEL (500 mm) (1)(2) LOOSE IN BOX URAC (V) DIMENSIONS wxhxl (mm) CAP. (μF) MASS (g) (3) SHORT LEADS lt = 3.5 mm ± 0.3 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm H = 18.5 mm P0 = 12.7 mm SPQ SPQ PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 20 % 0.15 0.22 6.0 x 15.5 x 26.0 2.4 0.33 0.47 7.0 x 16.5 x 26.0 2.9 29041 29277 29051 29278 20334 29147 20474 29148 29087 300 29093 500 26334 200 26474 500 29044 600 29053 550 23334 450 23474 400 PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 10 % 0.12 29037 - 29085 29039 0.15 29042 29285 29088 29045 29047 - 29091 29049 29054 600 0.18 6.0 x 15.5 x 26.0 2.4 300 550 0.22 29052 29286 29094 0.27 21274 - 27274 24274 0.33 21334 29171 27334 24334 21394 - 27394 24394 27474 24474 500 310 450 0.39 7.0 x 16.5 x 26.0 2.9 0.47 200 21474 29172 400 PITCH = 22.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 5 % 0.12 29038 - 29086 29064 0.15 29043 - 29089 29046 600 0.18 29048 - 0.22 6.0 x 15.5 x 26.0 2.4 22224 - 300 29092 28224 29065 0.27 22274 - 28274 25274 0.33 22334 - 28334 25334 22394 - 28394 25394 550 500 25224 450 7.0 x 16.5 x 26.0 0.39 2.9 200 400 Notes • SPQ = Standard Packing Quantity (1) H = In-tape height; P = sprocket hole distance; for detailed specifications refer to packaging information: www.vishay.com/doc?28139 0 (2) Reel diameter = 356 mm is available on request (3) Weight for short lead product only Revision: 23-Feb-16 Document Number: 28120 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents ELECTRICAL DATA AND ORDERING CODE - PITCH 27.5 mm CATALOG NUMBER BFC2 336 ..... AND PACKAGING URAC (V) CAP. (μF) DIMENSIONS wxhxl (mm) LOOSE IN BOX MASS (g) (1) SHORT LEADS lt = 3.5 mm ± 0.3 mm lt = 5.0 mm ± 1.0 mm LONG LEADS SPQ lt = 25.0 mm ± 2.0 mm SPQ 150 PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 20 % 0.47 9.0 x 19.0 x 31.5 29055 29279 29095 20684 29149 26684 5.5 0.68 1.0 11.0 x 21.0 x 31.0 7.4 20105 29151 100 26105 125 1.5 13.0 x 23.0 x 31.0 9.2 20155 29152 26155 2.2 15.0 x 25.0 x 31.5 12.3 20225 29153 26225 75 150 PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 10 % 0.47 0.56 9.0 x 19.0 x 31.5 5.5 0.68 0.82 11.0 x 21.0 x 31.0 1.2 13.0 x 23.0 x 31.0 29096 - 27564 21684 29173 27684 21824 - 27824 21105 29174 21125 - 27125 21155 29175 27155 21185 - 27185 21225 29176 27225 125 100 27105 9.2 1.5 1.8 15.0 x 25.0 x 31.5 29287 21564 7.4 1.0 310 29056 12.3 2.2 75 PITCH = 27.5 mm ± 0.4 mm; dt = 0.80 mm ± 0.08 mm; C-TOL. = ± 5 % 0.47 0.56 9.0 x 19.0 x 31.5 5.5 0.68 0.82 11.0 x 21.0 x 31.0 - 28474 22564 - 28564 22684 - 28684 22824 - 28824 22105 - 22125 - 1.2 100 28105 28125 9.2 1.5 22155 - 28155 1.8 22185 - 28185 22225 - 28225 15.0 x 25.0 x 31.5 2.2 125 7.4 1.0 13.0 x 23.0 x 31.0 22474 12.3 75 Notes • SPQ = Standard Packing Quantity (1) Weight for short lead product only Revision: 23-Feb-16 Document Number: 28120 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents APPROVALS SAFETY APPROVALS X2 VOLTAGE VALUE FILE NUMBERS LINK 310 VAC 1 nF to 2.2 μF FI 2013003 www.vishay.com/doc?28179 UL 60384-14 310 VAC 1 nF to 2.2 μF E354331 CSA-E 384-14 310 VAC 1 nF to 2.2 μF E354331 CQC 310 VAC 1 nF to 2.2 μF CB test certificate 310 VAC 1 nF to 2.2 μF EN60384-14 (ENEC) (= IEC 60384-14 ed-3) www.vishay.com/doc?28184 CQC07001021280 (L) www.vishay.com/doc?28199 CQC04001009262 (F) www.vishay.com/doc?28200 FI 7755 www.vishay.com/doc?28175 The ENEC-approval together with the CB-certificate replace all national marks of the following countries (they have already signed the ENEC-agreement): Austria; Belgium; Czech. Republic; Denmark; Finland; France; Germany; Greece; Hungary; Ireland; Italy; Luxembourg; Netherlands; Norway; Portugal; Slovenian; Spain; Sweden; Switzerland and United Kingdom. MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards.The capacitors packed in bandoliers are designed for mounting in pinted-circuit boards by means of automatic insertion machines. For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be insured that the stand-off pips are in good contact with the printed circuit board: • For pitches 15 mm capacitors shall be mechanically fixed by the leads • For larger pitches the capacitors shall be mounted in the same way and the body clamped. Space Requirements on Printed Circuit Board The maximum space for length (Imax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed circuit board is shown in the drawings. • For products with pitch 15 mm, w = l = 0.3 mm; h = 0.1 mm • For products with 15 mm < pitch 27.5 mm, w = l = 0.5 mm; h = 0.1 mm Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned. wmax. = W + Δ Eccentricity Imax. = I + Δ CBA116 hmax. = h + Δ Seating plane SOLDERING CONDITIONS For general soldering conditions and wave soldering profile, we refer to the application note: “Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171 Storage Temperature Tstg = - 25 °C to + 35 °C with RH maximum 75 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient temperature of 23 °C ± 1 °C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %. For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Revision: 23-Feb-16 Document Number: 28120 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents CHARACTERISTICS 10 3 2 1n F 4.7 10 nF nF Impedance (Ω) ΔC/C (%) 4 typical 47 n 10 F 0n F 10 1 0 47 0 10 nF 00 nF max. -2 10 0 -4 10 -1 min. -6 0 - 50 50 10 -2 4 10 Tamb (°C) 100 10 5 10 6 10 7 f (Hz) 10 8 Impedance as a function of frequency (typical curve) Capacitance as a function of ambient temperature (typical curve) 102 f (MHz) Dissipation factor (x 10-4) 103 101 102 µF F >1 1µ C C≤ F F < 220 n 0n 22 < C ≤ F 47 n nF 47 F < C ≤ nF 0 n 1 10 C≤ 101 X2 100 0 10 1 10 102 103 104 f (Hz) 105 10-1 1 3 100 1000 C (nF) 10 000 AC current (mA) 10 4 AC voltage (V) 10 10 Resonant frequency as a function of capacitance (typical curve) Tangent of loss angle as a function of frequency (typical curve) 10 2200 nF 1000 nF 470 nF 2 100 nF 10 2 47 nF 10 1 10 nF 4.7 nF 10 0 1nF Tamb ≤ 110 °C 10 1 1 10 10 Tamb ≤ 110 °C 2 10 3 10 4 f (Hz) 10 5 Max. RMS voltage as a function of frequency (typical curve) Revision: 23-Feb-16 10 -1 10 1 10 2 10 3 10 4 f (Hz) 10 5 Max. RMS current as a function of frequency (typical curve) Document Number: 28120 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents RC (s) 106 105 104 20 0 40 60 80 100 Tamb (°C) Insulation resistance APPLICATION NOTES • For X2 electromagnetic interference suppression in standard across the line applications (50/60 Hz) with a maximum mains voltage of 310 VAC. • For series impedance applications we refer to the application note www.vishay.com/doc?28153 • For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information depending of the capacitance value and the number of parallel connections contact: [email protected]. • These capacitors are not intended for continuous pulse applications. For these situations, capacitors of the AC and pulse programs must be used. • The maximum ambient temperature must not exceed 110 °C (125 °C for less than 1000 h) for C 470 nF and 110 °C for C > 470 nF • Rated voltage pulse slope: If the pulse voltage is lower than the rated voltage, the values of the specific reference data can be multiplied by 435 VDC and divided by the applied voltage INSPECTION REQUIREMENTS General Notes Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, IEC Publication IEC 60384-14 ed 3 and Specific Reference Data”. GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapters “General Data” of this specification Initial measurements Capacitance Tangent of loss angle: For C 1 μF at 10 kHz For C > 1 μF at 1 kHz 4.3 Robustness of terminations Tensile: Load 10 N; 10 s Bending: Load 5 N; 4 x 90° 4.4 Resistance to soldering heat No pre-drying Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s Revision: 23-Feb-16 No visible damage Document Number: 28120 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.19 Component solvent resistance Isopropylalcohol at room temperature Method: 2 Immersion time: 5 min ± 0.5 min Recovery time: Min. 1 h, max. 2 h 4.4.2 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % of the value measured initially Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured initially Insulation resistance As specified in section “Insulation resistance” of this specification SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 Initial measurements Capacitance Tangent of loss angle: For C 1 μF at 10 kHz For C > 1 μF at 1 kHz 4.20 Solvent resistance of the marking: see section “General notes”; item 5 Isopropylalcohol at room temperature Method: 1 Rubbing material: Cotton wool Immersion time: 5 min ± 0.5 min 4.6 A = - 55 °C B = + 110 °C 5 cycles Duration t = 30 min Rapid change of temperature 4.6.1 Inspection Visual examination 4.7 Mounting: See section “Mounting” of this specification Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s2 (whichever is less severe) Total duration 6 h Vibration 4.7.2 Final inspection Visual examination 4.9 Mounting: See section “Mounting” for more information Pulse shape: Half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms Shock Revision: 23-Feb-16 No visible damage Legible marking No visible damage No visible damage Document Number: 28120 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 4.9.2 Final measurements Visual examination No visible damage Capacitance |C/C| 5 % of the value measured initially Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured initially Insulation resistance As specified in section “Insulation resistance” of this specification SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.11 Climatic sequence 4.11.1 Initial measurements Capacitance Measured in 4.4.2 and 4.9.2 Tangent of loss angle: Measured initially in C1A and C1B 4.11.2 Dry heat Temperature: 110 °C 4.11.3 Damp heat cyclic Test Db First cycle Duration: 16 h 4.11.4 Cold Temperature: - 55 °C 4.11.5 Damp heat cyclic Test Db remaining cycles Duration: 2 h 4.11.6 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured in 4.11.1. Voltage proof 1350 VDC; 1 min between terminations No permanent breakdown or flash-over Insulation resistance 50 % of values specified in section “Insulation resistance” of this specification SUB GROUP C2 4.12 Damp heat steady state 4.12.1 Initial measurements Revision: 23-Feb-16 56 days, 40 °C, 90 % to 95 % RH No load Capacitance Tangent of loss angle at 1 kHz Document Number: 28120 12 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB GROUP C2 4.12.3 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % of the value measured in 4.12.1. Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured in 4.12.1. Voltage proof 1350 VDC; 1 min between terminations No permanent breakdown or flash-over Insulation resistance 50 % of values specified in section “Insulation resistance” of this specification SUB-GROUP C3 4.13.1 Initial measurements Capacitance Tangent of loss angle: For C 1 μF at 10 kHz For C > 1 μF at 1 kHz 4.13 Impulse voltage 3 successive impulses, full wave, peak voltage: 2.5 kV for C 1 μF 2.5 kV/C for C > 1 μF Max. 24 pulses 4.14 Endurance Duration: 1000 h 1.25 x URAC at 110 °C Once in every hour the voltage is increased to 1000 VRMS for 0.1 s via resistor of 47 ± 5 % 4.14.7 Final measurements No selfhealing breakdowns or flashover Visual examination No visible damage Legible marking Capacitance |C/C| 10 % compared to values measured in 4.13.1. Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured in 4.13.1. Voltage proof 1350 VDC; 1 min between terminations 2120 VAC; 1 min between terminations and case No permanent breakdown or flash-over Insulation resistance 50 % of values specified in section “Insulation resistance” of this specification SUB-GROUP C4 4.15 Charge and discharge Revision: 23-Feb-16 10 000 cycles Charged to 435 VDC Discharge resistance: 435 V DC R = ------------------------------------------------ 1.25 x C dU/dt Document Number: 28120 13 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs, Use MKP339 X2 MKP336 2 X2 www.vishay.com Vishay BCcomponents GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C4 4.15.1 Initial measurements Capacitance Tangent of loss angle: For C 1 μF at 10 kHz For C > 1 μF at 1 kHz 4.15.3 Final measurements Capacitance |C/C| 10 % compared to values measured in 4.15.1. Tangent of loss angle Increase of tan : 0.008 for: C 1 μF or 0.005 for: C > 1 μF Compared to values measured in 4.15.1. Insulation resistance 50 % of values specified in section “Insulation resistance” of this specification Resonance frequency 0.9 times the value as specified in section “Resonant frequency” of this specification Bore of gas jet: Ø 0.5 mm Fuel: Butane Test duration for actual volume V in mm3: V 250: 10 s 250 < V 500: 20 s 500 < V 1750: 30 s V > 1750: 60 s One flame application After removing test flame from capacitor, the capacitor must not continue to burn for more than 10 s. No burning particle must drop from the sample. SUB-GROUP C5 4.16 Radio frequency characteristic SUB-GROUP C6 4.17 Passive flammability Class B 12 mm ~ 8 mm 45.0° SUB-GROUP C7 4.18 Active flammability Revision: 23-Feb-16 20 cycles of 2.5 kV discharges on the test capacitor connected to URAC. The cheese cloth around the capacitors shall not burn with a flame. No electrical measurements are required. Document Number: 28120 14 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000