Series ANP2 www.vishay.com Vishay Wet Tantalum Capacitor, Button, All-Tantalum Case, Non-Polar, - 55 °C to + 125 °C Operation FEATURES • All-Tantalum electrodes eliminate silver migration • Withstands high ripple current • Long life reliability • Non-polar design PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 125 °C INTRODUCTION This conveniently-packaged non-polar button unit employs a non-solid electrolyte, and has a sintered tantalum anode. The anode is produced from medium capacitance powder and the lower CV product allows a tighter specification of capacitance stability, dissipation factor and leakage current. The cathode is also of tantalum, and overcomes the restrictions of a silver cathode system in allowing a high ripple current rating. The ANP2 capacitor is based upon the CH capacitor design, but with twin tantalum electrodes made of sintered compacts of high purity tantalum powder. The dielectric layer of tantalum pentoxide is formed on each compact to withstand rated voltage. This enables the capacitor to be used where DC bias may fluctuate positively or negatively. The system is then enclosed between a tantalum plate and a tantalum cup, with an outer nickel case. The seal is a highly efficient system comprising a PTFE gasket clamped between coined plates of tantalum by a work-hardened nickel ring. This type of seal, common to all button styles, is largely responsible for their long life and high reliability under severe military environments. The combination of the tantalum pentoxide dielectric stability and the extremely efficient seal has been shown to ensure that there is no significant difference in electrical parameters or instant use behaviour after 10 years storage or longer. A shelf life in excess of 20 years is confidently expected. There are four types of terminations and mounting options are available. These include a treated stud or bolt, PCB pins, a tab for panels, and ribbons leads slotted through-holes. These are illustrated in the photograph, and dimensional table drawing. Voltage Range: 3 VDC to 75 VDC Capacitance Range: 33 μF to 470 μF SPECIFICATIONS Environmental classification: 55/125/56 Vibration: 10 Hz to 2000 Hz, 0.75 mm or 98 m/s2, 150 h Bump: 390 m/s2, 4000 bumps Shock: 981 m/s2 Acceleration: 981 m/s2 Low air pressure: 1 kPa REVERSE VOLTAGE CAPABILITY The ANP2 employs twin tantalum electrodes, which allows the continuous application of full rated voltage in both directions. SURGE VOLTAGE The surge voltage capability is 115 % of the voltage rating at the relevant temperature. TEMPERATURE RANGE The capacitor is designed for operation between - 55 °C and + 125 °C, with linear voltage derating above + 85 °C to 66 % of the rated voltage at + 125 °C. CAPACITANCE TOLERANCE The standard capacitance tolerance is ± 20 % although special tolerances are available by arrangement. APPLICATIONS The ANP series is designed for use in general military and professional applications. For example: Power supply “smoothing”, filter networks, switching, by-pass, timer functions, and where reverse potential occur. WEIGHT The ANP2 style with a stud termination weighs approximately 18.1 g, including the nut. The ANP2 styles, which has a printed circuit board mounting, weighs approximately 17.3 g. Revision: 27-May-10 Document Number: 42099 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series ANP2 www.vishay.com Vishay APPLICATION INFORMATION RELIABILITY Capacitors may be operated at less than the rated voltage, resulting in significantly reduced leakage current values. All capacitors are subjected to burn-in. This is to remove infant mortalities and ensure reliability. The capacitor lifetime is enhanced when the unit is subjected to a reduced ripple current, a low ambient temperature, and is externally cooled. The use of a heat sink is recommended. In timing circuits, or other applications where the device is subjected only to a DC voltage, the ballistic or DC capacitance will be somewhat larger than measured at 50 Hz. ORDERING PROCEDURE The parametric information must necessarily be brief, although additional comprehensive data is available on request, and the tests tailored to customers’ requirements can be made. Example: ANP2C (220 μF, 10 VDC) Vishay Part Number: ANP2B227M010A ORDERING INFORMATION ANP2 C 227 M 100 A MODEL CASE CODE CAPACITANCE TOLERANCE VOLTAGE TERMINATION AND PACKAGING See Ratings and Case Codes Table This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow M = 20 % (std) This is expressed in volts. K = 10 % To complete the three-digit (special order) block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V) - Blank = Standard (tin/lead coating) A = Stud B = PC mount pins C = Twin tag or ribbon D = Panel or potting tag DIMENSIONS in millimeters The ANP2 series is comprised of two case sizes, differing in depth of cup only. The case size dimensions are shown in the table. Four mounting styles are available in both case sizes. Stud D B PC Pins Potting Tag + + (2) Twin Tag or Ribbons + + A J E N Hole Q dia. G - H Mounting holes M dia. F 20 S.W.G. H.T.D. Nickel 4 BA shakeproof nut P This mounting style is suitable for panel thickness of up to 1.2 mm Hole T dia. L crs. R - S W U crs. Mounting holes V dia. K crs. A 3.6 B C D 6.7 (1) 21.8 8.4 (2) E F G H J K crs. L crs. M N P dia. nom. dia. 8.4 16.2 8.4 1.8 0.8 20.3 10.2 1.1 2.4 13.1 Q R S T dia. U crs. V W dia. nom. 1.0 7.5 10.7 1.6 13.0 3.5 0.30 Notes • All dimensions are in mm, and are maximum unless otherwise stated (1) For C case size, case height is 8.5 mm (2) Width of anode tag 4.22 mm max. Revision: 27-May-10 Document Number: 42099 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series ANP2 www.vishay.com Vishay STANDARD RATINGS PART NUMBER CASE CODE CAPACITANCE AT 50 Hz (μF) DISSIPATION FACTOR AT 50 Hz (%) 25 °C 125 °C MAX. ESR AT 100 kHz () 25 °C MAX. DCL (μA) C AT 50 Hz (%) - 55 °C 25 °C 125 °C - 55 °C 125 °C 3 VDC AT 85 °C; 2 VDC AT 125 °C ANP2C477(1)003(2) C 470 ANP2B337(1)003(2) B 330 25 38 1.0 5.0 2.0 50 - 40 25 20 30 1.0 5.0 2.0 50 - 40 20 6 VDC AT 85 °C; 4 VDC AT 125 °C ANP2C337(1)006(2) C 330 ANP2B227(1)006(2) B 220 20 30 1.0 5.0 2.0 50 - 35 15 15 20 1.0 5.0 2.0 50 - 35 15 10 VDC AT 85 °C; 6.6 VDC AT 125 °C ANP2C227(1)010(2) C 220 ANP2B157(1)010(2) B 150 15 20 1.0 5.0 2.0 50 - 35 12.5 12 15 1.0 5.0 2.0 50 - 30 12.5 15 VDC AT 85 °C; 10 VDC AT 125 °C ANP2C157(1)015(2) C 150 12 15 1.0 5.0 2.0 50 - 30 12.5 ANP2B107(1)015(2) B 100 10 12 1.0 5.0 2.0 50 - 30 12.5 20 VDC AT 85 °C; 13.4 VDC AT 125 °C ANP2C107(1)020(2) C 100 10 12 1.0 5.0 2.0 50 - 30 12.5 ANP2B686(1)020(2) B 68 10 12 1.0 5.0 2.0 50 - 30 12.5 30 VDC AT 85 °C; 20 VDC AT 125 °C ANP2C686(1)030(2) C 68 8.0 10 1.0 5.0 2.0 50 - 20 12.5 ANP2B476(1)030(2) B 47 8.0 10 1.0 5.0 2.0 50 - 20 12.5 ANP2C476(1)040(2) C 47 6.0 7.0 1.0 5.0 2.0 50 - 15 12.5 ANP2B336(1)040(2) B 33 6.0 7.0 1.0 5.0 2.0 50 - 15 12.5 ANP2C336(1)050(2) C 33 5.0 6.0 1.0 5.0 2.0 50 - 10 12.5 ANP2B226(1)050(2) B 22 5.0 6.0 1.0 5.0 2.0 50 - 10 12.5 ANP2C226(1)075(2) C 22 3.0 3.0 1.0 5.0 2.0 50 - 5.0 12.5 ANP2B156(1)075(2) B 15 3.0 3.0 1.0 5.0 2.0 50 - 5.0 12.5 40 VDC AT 85 °C; 26.6 VDC AT 125 °C 50 VDC AT 85 °C; 33.3 VDC AT 125 °C 75 VDC AT 85 °C; 50 VDC AT 125 °C Notes • Part number definitions: (1) Capacitance tolerance M = 20 % standard K = 10 % special order (2) Termination type A = Stud or bolt B = Pins for PCB C = Twin tags or ribbons D = Potting tag Revision: 27-May-10 Document Number: 42099 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series ANP2 www.vishay.com Vishay CROSS REFERENCE VISHAY PART NUMBER ARCOTRONICS PART NUMBER ANP2C226M075A 402/1/50040/002 NATO PART NUMBER 5910-99-014-3038 ANP2B156M075A 402/1/50039/001 5910-99-014-3037 ANP2C336M050A 402/1/50040/003 5910-99-014-3040 ANP2B226M050A 402/1/50039/002 5910-99-014-3039 ANP2C476M040A 402/1/50040/004 5910-99-014-3042 5910-99-014-3041 ANP2B336M040A 402/1/50039/003 ANP2C686M030A 402/1/50040/005 5910-99-014-3044 ANP2B476M030A 402/1/50039/004 5910-99-014-3043 ANP2C107M020A 402/1/50040/006 5910-99-014-3046 ANP2B686M020A 402/1/50039/005 5910-99-014-3045 ANP2C157M015A 402/1/50040/007 5910-99-014-3048 ANP2B107M015A 402/1/50039/006 5910-99-014-3047 ANP2C227M010A 402/1/50040/008 5910-99-014-3050 5910-99-014-3049 ANP2B157M010A 402/1/50039/007 ANP2C337M006A 402/1/50040/009 5910-99-014-3052 ANP2B227M006A 402/1/50039/008 5910-99-014-3051 ANP2C477M003A 402/1/50040/010 5910-99-014-3055 ANP2B337M003A 402/1/50039/009 5910-99-014-3053 ANP2C226K075A 402/1/50040/022 n/a ANP2B156K075A 402/1/50039/021 n/a ANP2C336K050A 402/1/50040/023 n/a ANP2B226K050A 402/1/50039/022 n/a ANP2C476K040A 402/1/50040/024 n/a ANP2B336K040A 402/1/50039/023 n/a ANP2C686K030A 402/1/50040/025 n/a ANP2B476K030A 402/1/50039/024 n/a ANP2C107K020A 402/1/50040/026 n/a ANP2B686K020A 402/1/50039/025 n/a ANP2C157K015A 402/1/50040/027 n/a ANP2B107K015A 402/1/50039/026 n/a ANP2C227K010A 402/1/50040/028 n/a ANP2B157K010A 402/1/50039/027 n/a ANP2C337K006A 402/1/50040/029 n/a ANP2B227K006A 402/1/50039/028 n/a ANP2C477K003A 402/1/50040/030 n/a ANP2B337K003A 402/1/50039/029 n/a ANP2C226M075D 402/1/50042/002 5910-99-014-3102 5910-99-014-3101 ANP2B156M075D 402/1/50041/001 ANP2C336M050D 402/1/50042/003 5910-99-014-3104 ANP2B226M050D 402/1/50041/002 5910-99-014-3103 ANP2C476M040D 402/1/50042/004 5910-99-014-3106 ANP2B336M040D 402/1/50041/003 5910-99-014-3105 ANP2C686M030D 402/1/50042/005 5910-99-014-3108 ANP2B476M030D 402/1/50041/004 5910-99-014-3107 ANP2C107M020D 402/1/50042/006 5910-99-014-3110 5910-99-014-3109 ANP2B686M020D 402/1/50041/005 ANP2C157M015D 402/1/50042/007 5910-99-014-3112 ANP2B107M015D 402/1/50041/006 5910-99-014-3111 ANP2C227M010D 402/1/50042/008 5910-99-014-3114 Revision: 27-May-10 Document Number: 42099 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series ANP2 www.vishay.com Vishay CROSS REFERENCE VISHAY PART NUMBER ARCOTRONICS PART NUMBER NATO PART NUMBER ANP2B157M010D 402/1/50041/007 5910-99-014-3113 ANP2C337M006D 402/1/50042/009 5910-99-014-3116 ANP2B227M006D 402/1/50041/008 5910-99-014-3115 ANP2C477M003D 402/1/50042/010 5910-99-014-3118 ANP2B337M003D 402/1/50041/009 5910-99-014-3117 ANP2C226K075D 402/1/50042/022 n/a ANP2B156K075D 402/1/50041/021 n/a ANP2C336K050D 402/1/50042/023 n/a ANP2B226K050D 402/1/50041/022 n/a ANP2C476K040D 402/1/50042/024 n/a ANP2B336K040D 402/1/50041/023 n/a ANP2C686K030D 402/1/50042/025 n/a ANP2B476K030D 402/1/50041/024 n/a ANP2C107K020D 402/1/50042/026 n/a ANP2B686K020D 402/1/50041/025 n/a ANP2C157K015D 402/1/50042/027 n/a ANP2B107K015D 402/1/50041/026 n/a ANP2C227K010D 402/1/50042/028 n/a ANP2B157K010D 402/1/50041/027 n/a ANP2C337K006D 402/1/50042/029 n/a ANP2B227K006D 402/1/50041/028 n/a ANP2C477K003D 402/1/50042/030 n/a ANP2B337K003D 402/1/50041/029 n/a ANP2C226M075B 402/1/50150/002 5910-99-014-3070 ANP2B156M075B 402/1/50149/001 5910-99-014-3069 ANP2C336M050B 402/1/50150/003 5910-99-014-3072 ANP2B226M050B 402/1/50149/002 5910-99-014-3071 ANP2C476M040B 402/1/50150/004 5910-99-014-3074 ANP2B336M040B 402/1/50149/003 5910-99-014-3073 ANP2C686M030B 402/1/50150/005 5910-99-014-3076 ANP2B476M030B 402/1/50149/004 5910-99-014-3075 ANP2C107M020B 402/1/50150/006 5910-99-014-3078 ANP2B686M020B 402/1/50149/005 5910-99-014-3077 ANP2C157M015B 402/1/50150/007 5910-99-014-3080 ANP2B107M015B 402/1/50149/006 5910-99-014-3079 ANP2C227M010B 402/1/50150/008 5910-99-014-3082 ANP2B157M010B 402/1/50149/007 5910-99-014-3081 ANP2C337M006B 402/1/50150/009 5910-99-014-3084 ANP2B227M006B 402/1/50149/008 5910-99-014-3083 ANP2C477M003B 402/1/50150/010 5910-99-014-3086 ANP2B337M003B 402/1/50149/009 5910-99-014-3085 ANP2C226K075B 402/1/50150/022 n/a ANP2B156K075B 402/1/50149/021 n/a ANP2C336K050B 402/1/50150/023 n/a ANP2B226K050B 402/1/50149/022 n/a ANP2C476K040B 402/1/50150/024 n/a ANP2B336K040B 402/1/50149/023 n/a ANP2C686K030B 402/1/50150/025 n/a ANP2B476K030B 402/1/50149/024 n/a Revision: 27-May-10 Document Number: 42099 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Series ANP2 www.vishay.com Vishay CROSS REFERENCE VISHAY PART NUMBER ARCOTRONICS PART NUMBER NATO PART NUMBER ANP2C107K020B 402/1/50150/026 n/a n/a ANP2B686K020B 402/1/50149/025 ANP2C157K015B 402/1/50150/027 n/a ANP2B107K015B 402/1/50149/026 n/a ANP2C227K010B 402/1/50150/028 n/a ANP2B157K010B 402/1/50149/027 n/a ANP2C337K006B 402/1/50150/029 n/a ANP2B227K006B 402/1/50149/028 n/a ANP2C477K003B 402/1/50150/030 n/a ANP2B337K003B 402/1/50149/029 n/a ANP2C226M075C 402/1/50044/002 n/a ANP2B156M075C 402/1/50043/001 n/a ANP2C336M050C 402/1/50044/003 n/a ANP2B226M050C 402/1/50043/002 n/a ANP2C476M040C 402/1/50044/004 n/a ANP2B336M040C 402/1/50043/003 n/a ANP2C686M030C 402/1/50044/005 n/a ANP2B476M030C 402/1/50043/004 n/a ANP2C107M020C 402/1/50044/006 n/a ANP2B686M020C 402/1/50043/005 n/a ANP2C157M015C 402/1/50044/007 n/a ANP2B107M015C 402/1/50043/006 n/a ANP2C227M010C 402/1/50044/008 n/a ANP2B157M010C 402/1/50043/007 n/a ANP2C337M006C 402/1/50044/009 n/a ANP2B227M006C 402/1/50043/008 n/a ANP2C477M003C 402/1/50044/010 n/a ANP2B337M003C 402/1/50043/009 n/a ANP2C226K075C 402/1/50044/022 n/a ANP2B156K075C 402/1/50043/021 n/a ANP2C336K050C 402/1/50044/023 n/a ANP2B226K050C 402/1/50043/022 n/a ANP2C476K040C 402/1/50044/024 n/a ANP2B336K040C 402/1/50043/023 n/a ANP2C686K030C 402/1/50044/025 n/a ANP2B476K030C 402/1/50043/024 n/a ANP2C107K020C 402/1/50044/026 n/a ANP2B686K020C 402/1/50043/025 n/a ANP2C157K015C 402/1/50044/027 n/a ANP2B107K015C 402/1/50043/026 n/a ANP2C227K010C 402/1/50044/028 n/a ANP2B157K010C 402/1/50043/027 n/a ANP2C337K006C 402/1/50044/029 n/a ANP2B227K006C 402/1/50043/028 n/a ANP2C477K003C 402/1/50044/030 n/a ANP2B337K003C 402/1/50043/029 n/a Revision: 27-May-10 Document Number: 42099 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000