M35 www.vishay.com Vishay Wet Tantalum Capacitors Surface Mount, Molded Case FEATURES • Molded surface mountable design • Terminations: standard tin/lead (SnPb), 100 % tin (RoHS compliant) available • Industry standard ratings • Model M35 wet tantalum electrolytic chip capacitors incorporate the advantages of all the varieties of electrolytic capacitors and eliminate most of the disadvantages. These units have a 3 V reverse voltage capability at + 85 °C and a higher ripple current capability than any other electrolytic type with similar combinations of capacitance and case size. • Compliant to RoHS Directive 2002/95/EC Note * Pb containing terminations are not RoHS compliant, exemptions may apply PERFORMANCE CHARACTERISTICS Life Test: Capacitors are capable of withstanding a 2000 h life test at a temperature of + 85 °C or + 125 °C at the applicable rated DC working voltage. Following life test: 1. DCL, measured at + 85 °C rated voltage, shall not be in excess of the original requirement. 2. The equivalent series resistance shall not exceed 150 % of the initial requirement. 3. Change in capacitance shall not exceed 10 % from the initial measurement. Operating Temperature: - 55 °C to + 85 °C (to + 125 °C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 °C. ± 20 % standard. ± 10 %, ± 5 % available as special. DC Leakage Current (DCL Max.): At + 25 °C and above: Leakage current shall not exceed the values listed in the Standard Ratings Tables. ORDERING INFORMATION M35 C 826 M 125 B Z S L MODEL CASE CODE CAPACITANCE CAPACITANCE TOLERANCE DC VOLTAGE RATING AT + 85 °C TERMINATION AND PACKAGING RELIABILITY LEVEL TEMP ESR See Ratings and Case Codes table This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. K = ± 10 % M = ± 20 % This is expressed in volts. To complete the three-digit block, zeros precede the voltage rating. A decimal point is indicated by an “R” (6R3 = 6.3 V) A = 100 % tin (RoHS compliant), bulk B = Std, tin/lead, bulk Z = Non-ER S = Std S = Std. L = Low Note • Packaging: The use of formed plastic tubes for packing bulk components is standard TH H TW DIMENSIONS in inches [millimeters] W L P CASE CODE L (MAX.) W H P (MIN.) TW TH (MIN.) C 0.835 [21.2] 0.315 ± 0.012 [8 ± 0.3] 0.295 ± 0.012 [7.5 ± 0.3] 0.118 [3.0] 0.236 ± 0.012 [6.0 ± 0.3] 0.075 [1.9] Revision: 07-Nov-11 Document Number: 40095 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 M35 www.vishay.com Vishay RECOMMENDED REFLOW PROFILES Tp °C tp TEMPERATURE (°C) TL °C Ts MAX. °C (tL) Ts MIN. °C PREHEAT (ts) 25 °C TIME (s) ALL CASE CODES Tp Tp Lead (Pb)-free Sn/Pb 260 °C tp TL Ts MIN. Ts MAX. Ts MAX. ts TL Ts MIN. Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free Sn/Pb Lead (Pb)-free 240 °C 10 217 °C 183 °C 150 °C 100 °C 200 °C 150 °C 60 to 150 ts Sn/Pb tL 60 to 90 60 MOUNTING Due to the size and weight of these capacitors, we recommend that a supplemental mounting restraint to be used in printed circuit board attachment in addition to the reflowed solder. One recommendation is to use an adhesive such as defined in the J-STD-001DS. This is the Space Application Electronic Hardware Addendum to J-STD-001 (Requirements for Solder Electrical and Electronic Assemblies). STANDARD RATINGS MAX. RIPPLE 40 kHz + 85 °C RMS - 55 °C + 85 °C + 125 °C + 25 °C + 125 °C (mA) MAX. DCL (μA) AT MAX. ESR MAX. ESR AT + 25 °C AT - 55 °C CAPACITANCE (μF) CASE CODE PART NUMBER 30 C M35C306(1)006(2)ZS(3) MAX. CAPACITANCE CHANGE (%) AT 6 VDC AT + 85 °C; 4 VDC AT + 125 °C 4.0 100 1.0 2.0 - 40 + 10.5 + 12 820 68 C M35C686(1)006(2)ZS(3) 3.2 60 1.0 2.0 - 40 + 14 + 16 960 220 C M35C227(1)006(2)ZS(3) 3.0 36 2.0 9.0 - 64 + 13 + 16 1000 25 C M35C256(1)008(2)ZS(3) 4.0 100 1.0 2.0 - 40 + 10.5 + 12 820 56 C M35C566(1)008(2)ZS(3) 3.3 59 1.0 2.0 - 40 + 14 + 16 900 180 C M35C187(1)008(2)ZS(3) 3.0 45 2.0 9.0 - 60 + 13 + 16 1000 20 C M35C206(1)010(2)ZS(3) 4.0 120 1.0 2.0 - 32 + 10.5 + 12 820 47 C M35C476(1)010(2)ZS(3) 3.7 90 1.0 2.0 - 36 + 14 + 16 855 120 C M35C127(1)010(2)ZS(3) 3.2 54 2.0 6.0 - 40 + 14 + 16 900 150 C M35C157(1)010(2)ZS(3) 3.0 54 2.0 9.0 - 55 + 13 + 16 900 8 VDC AT + 85 °C; 5 VDC AT + 125 °C 10 VDC AT + 85 °C; 7 VDC AT + 125 °C Note • Part number definitions: (1) Capacitance tolerance: K, M (2) Termination/packaging: (see Ordering Information) Reliability level: Z = Non-ER Temperature: S = STD (3) ESR: S = STD, L = Low (1/2 standard ESR value) Revision: 07-Nov-11 Document Number: 40095 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 M35 www.vishay.com Vishay STANDARD RATINGS MAX. RIPPLE 40 kHz + 85 °C RMS + 25 °C + 125 °C - 55 °C + 85 °C + 125 °C (mA) MAX. DCL (μA) AT MAX. ESR MAX. ESR AT + 25 °C AT - 55 °C CAPACITANCE (μF) CASE CODE PART NUMBER 15 33 82 100 C C C C M35C156(1)015(2)ZS(3) M35C336(1)015(2)ZS(3) M35C826(1)015(2)ZS(3) M35C107(1)015(2)ZS(3) 10 22 56 68 C C C C M35C106(1)025(2)ZS(3) M35C226(1)025(2)ZS(3) M35C566(1)025(2)ZS(5) M35C686(1)025(2)ZS(5) 8 15 47 56 C C C C M35C805(1)030(2)ZS(3) M35C156(1)030(2)ZS(3) M35C476(1)030(2)ZS(3) M35C566(1)030(2)ZS(3) 15 39 C C M35C156(1)035(2)ZS(3) M35C396(1)035(2)ZS(3) 5 10 33 C C C M35C505(1)050(2)ZS(3) M35C106(1)050(2)ZS(3) M35C336(1)050(2)ZS(3) 4 8.2 27 C C C M35C405(1)060(2)ZS(3) M35C825(1)060(2)ZS(3) M35C276(1)060(2)ZS(3) 3.5 6.8 22 C C C M35C355(1)075(2)ZS(3) M35C685(1)075(2)ZS(3) M35C226(1)075(2)ZS(3) 2.5 4.7 10 C C C M35C255(1)100(2)ZS(3) M35C475(1)100(2)ZS(3) M35C106(1)100(2)ZS(3) 1.7 3.6 6.8 C C C M35C175(1)125(2)ZS(3) M35C365(1)125(2)ZS(3) M35C685(1)125(2)ZS(3) MAX. CAPACITANCE CHANGE (%) AT 15 VDC AT + 85 °C; 10 VDC AT + 125 °C 4.4 4.0 3.9 3.9 155 90 72 72 1.0 1.0 2.0 2.0 2.0 2.0 6.0 9.0 - 24 - 28 - 35 - 44 + 10.5 + 14 + 12 + 13 + 12 + 16 + 16 + 16 780 820 900 900 2.0 2.0 6.0 9.0 - 16 - 20 - 25 - 40 +8 + 10.5 + 12 + 12 +9 + 12 + 15 + 15 715 800 850 850 2.0 2.0 6.0 9.0 - 16 - 20 - 23 - 38 +8 + 10.5 + 12 + 12 + 12 + 12 + 15 + 15 640 780 800 800 1.5 6.0 - 20 - 22 + 10.5 + 12 + 12 + 14 660 820 2.0 2.0 9.0 - 16 - 24 - 29 +5 +8 + 10 +6 +9 + 12 580 715 700 2.0 2.0 12 - 16 - 24 - 24 +5 +8 + 10 +6 +9 + 12 525 625 700 2.0 2.0 12 - 16 - 20 - 19 +5 +8 + 10 +6 +9 + 12 525 610 600 2.0 2.0 12 - 16 - 16 - 17 +7 +7 + 10 +8 +8 + 12 505 565 800 2.0 2.0 12 - 16 - 16 - 14 +7 +7 + 10 +8 +8 + 12 415 520 700 25 VDC AT + 85 °C; 15 VDC AT + 125 °C 5.3 4.2 4.3 4.3 220 140 90 90 1.0 1.0 2.0 2.0 30 VDC AT + 85 °C; 20 VDC AT + 125 °C 6.6 6.2 5.2 5.2 275 175 100 100 1.0 1.0 2.0 2.0 35 VDC AT + 85 °C; 22 VDC AT + 125 °C 6.2 4.1 175 61 0.75 2.0 50 VDC AT + 85 °C; 30 VDC AT + 125 °C 8.0 6.4 5.0 400 250 135 1.0 1.0 2.0 60 VDC AT + 85 °C; 40 VDC AT + 125 °C 9.3 6.6 5.0 550 275 144 1.0 1.0 3.0 75 VDC AT + 85 °C; 50 VDC AT + 125 °C 9.5 6.8 5.1 650 300 157 1.0 1.0 3.0 100 VDC AT + 85 °C; 65 VDC AT + 125 °C 10.6 8.5 5.9 950 500 200 1.0 1.0 3.0 125 VDC AT + 85 °C; 85 VDC AT + 125 °C 15.6 10.0 11.7 1250 600 300 1.0 1.0 3.0 Note • Part number definitions: (1) Capacitance tolerance: K, M (2) Termination/packaging: (see Ordering Information) Reliability level: Z = Non-ER Temperature: S = STD (3) ESR: S = STD, L = Low (1/2 standard ESR value) Revision: 07-Nov-11 Document Number: 40095 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 M35 www.vishay.com Vishay PERFORMANCE CHARACTERISTICS OF M35 CAPACITORS ELECTRICAL CHARACTERISTICS ITEM Operating temperature range Capacitor tolerance Capacitance change (maximum) ESR AC ripple current DCL (maximum leakage current) Impedance (maximum) PERFORMANCE CHARACTERISTICS - 55 °C to + 125 °C ± 20 %, ± 10 % at 120 Hz Limits per Standard Ratings table. Measured per requirements of MIL-PRF-39006. Reverse voltage shall be in accordance with MIL-PRF-39006/22. Units are capable of withstanding 3 V in reverse at + 85 °C for 125 h. Surge voltage shall be in accordance with MIL-PRF-39006. The DC rated surge voltage is the maximum voltage to which the capacitors should be subjected under any conditions. This includes transients and peak ripple at the highest line voltage. The surge voltage is 115 % of rated DC working voltage. The capacitors shall be capable of withstanding a 2000 h life test at 85 °C at rated voltage. Reverse voltage Surge voltage Life test ENVIRONMENTAL CHARACTERISTICS ITEM Hermeticity Moisture resistance Altitude/barometric pressure (reduced) CONDITION MIL-PRF-39006 MIL-PRF-39006 COMMENTS The internal component has been tested to be compliant to hermeticity requirements of MIL-PRF-39006/22. The internal component has been tested to be compliant to moisture resistance requirements of MIL-PRF-39006/22. The internal component has been tested to be compliant to altitude or reduced barometric pressure requirements MIL-PRF-39006/22 (150 000 feet). MIL-PRF-39006 the the the of MECHANICAL CHARACTERISTICS ITEM Thermal shock Shock Vibration (high frequency) Vibration (random) CONDITION MIL-STD-202, Method 107, A MIL-STD-202, Method 213 MIL-STD-202, Method 204 MIL-STD-202, Method 214 Resistance to solder heat MIL-STD-202, Method 210 Solderability ANSI J-STD-002 Part markings MIL-STD-1285 Weight (typical) in g 3.5 COMMENTS Per MIL-PRF-39006, 30 cycles Per MIL-PRF-39006, 500 g Per MIL-PRF-39006, 80 g Per MIL-PRF-39006, 53.79 g The capacitor must withstand solder dipping of the terminals at 260 °C for 10 s. The capacitor must not be visibly damaged and the electrical characteristics must not be affected. The terminations must be solderable per the requirements of MIL-PRF-55365 para. 4.10 The part marking shall include Vishay name, trademark, capacitance, voltage, date code and lot symbol. PAD DIMENSIONS in millimeters D A C CASE CODE C A (MIN.) 22.7 B B (NOM.) 14.7 C C (NOM.) 4.0 D (NOM.) 6.4 STANDARD PACKAGING QUANTITY SERIES M35 Revision: 07-Nov-11 CASE CODE C BULK/TUBE 10 pcs Document Number: 40095 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000