LM211 D

LM211, LM311
Single Comparators
The ability to operate from a single power supply of 5.0 V to 30 V or
$15 V split supplies, as commonly used with operational amplifiers,
makes the LM211/LM311 a truly versatile comparator. Moreover, the
inputs of the device can be isolated from system ground while the
output can drive loads referenced either to ground, the VCC or the VEE
supply. This flexibility makes it possible to drive DTL, RTL, TTL, or
MOS logic. The output can also switch voltages to 50 V at currents to
50 mA, therefore, the LM211/LM311 can be used to drive relays,
lamps or solenoids.
http://onsemi.com
MARKING
DIAGRAMS
8
Features
LM311AN
AWL
YYWWG
PDIP−8
N SUFFIX
CASE 626
• These Devices are Pb−Free and are RoHS Compliant
8
1
1
VCC
3.0k
VCC
RL
5.0k
5
2
6
+
Inputs
3
2
+
8 7
Inputs
3
Output
−
1
7
Inputs
3
2
Output
1
4
1
x
A
WL, L
YY, Y
WW, W
G
G
Single Supply
7
Inputs
−
1
1
VCC
8
+
Output
3
+
8
−
1
7
VEE
PIN CONNECTIONS
VEE
Input polarity is reversed when
GND pin is used as an output.
Input polarity is reversed when
GND pin is used as an output.
Ground−Referred Load
= 2 or 3
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
= Pb−Free Package
Output
RL
4
RL
LMx11
ALYW
G
4
VCC
2
SOIC−8
D SUFFIX
CASE 751
8
RL
-
VEE
4
VEE
Split Power Supply with Offset Balance
8
8
Load Referred to Negative Supply
GND
1
2
Inputs
3
VEE
+
−
4
8
VCC
7
Output
6
Balance/Strobe
5
Balance
VCC
(Top View)
2
VCC
2
Inputs
+
3
−
Inputs
8
7
RL
Output
3
8
+
7
Output
−
4
VEE
RL
1
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
6
TTL Strobe
1
4
1.0k
VEE
Load Referred to Positive Supply
Strobe Capability
Figure 1. Typical Comparator Design Configurations
© Semiconductor Components Industries, LLC, 2012
August, 2012 − Rev. 6
1
Publication Order Number:
LM211/D
LM211, LM311
ORDERING INFORMATION
Device
Shipping†
Package
LM211DG
98 Units / Rail
LM211DR2G
2500 Units / Tape & Reel
SOIC−8
(Pb−Free)
LM311DG
98 Units / Rail
LM311DR2G
2500 Units / Tape & Reel
LM311NG
PDIP−8
(Pb−Free)
50 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating
Total Supply Voltage
Symbol
LM211
LM311
Unit
VCC +⎥VEE⎥
36
36
Vdc
Output to Negative Supply Voltage
VO −VEE
50
40
Vdc
Ground to Negative Supply Voltage
VEE
30
30
Vdc
Input Differential Voltage
VID
±30
±30
Vdc
Input Voltage (Note 2)
Vin
±15
±15
Vdc
Voltage at Strobe Pin
−
VCC to VCC−5
VCC to VCC−5
Vdc
Power Dissipation and Thermal Characteristics
Plastic DIP
Derate Above TA = +25°C
Operating Ambient Temperature Range
Operating Junction Temperature
Storage Temperature Range
PD
RqJA
625
5.0
mW
mW/°C
TA
−25 to +85
0 to +70
°C
TJ(max)
+150
+150
°C
Tstg
−65 to +150
−65 to +150
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
LM211, LM311
ELECTRICAL CHARACTERISTICS (VCC = +15 V, VEE = −15 V, TA = 25°C, unless otherwise noted) Note 1
LM211
Characteristic
Symbol
LM311
Min
Typ
Max
Min
Typ
Max
−
−
0.7
−
3.0
4.0
−
−
2.0
−
7.5
10
Unit
Input Offset Voltage (Note 3)
RS ≤ 50 kW, TA = +25°C
RS ≤ 50 kW, Tlow ≤ TA ≤ Thigh*
VIO
mV
Input Offset Current (Note 3) TA = +25°C
Tlow ≤ TA ≤ Thigh*
IIO
−
−
1.7
−
10
20
−
−
1.7
−
50
70
nA
Input Bias Current TA = +25°C
Tlow ≤ TA ≤ Thigh*
IIB
−
−
45
−
100
150
−
−
45
−
250
300
nA
Voltage Gain
AV
40
200
−
40
200
−
V/mV
−
200
−
−
200
−
ns
−
−
0.75
−
1.5
−
−
−
−
0.75
−
1.5
−
−
0.23
−
0.4
−
−
−
−
0.23
−
0.4
−
3.0
−
−
3.0
−
mA
−
−
−
0.2
−
0.1
10
−
0.5
−
−
−
−
0.2
−
−
50
−
nA
nA
mA
VICR
−14.5
−14.7
to
13.8
+13.0
−14.5
−14.7
to
13.8
+13.0
V
Positive Supply Current
ICC
−
+2.4
+6.0
−
+2.4
+7.5
mA
Negative Supply Current
IEE
−
−1.3
−5.0
−
−1.3
−5.0
mA
Response Time (Note 4)
Saturation Voltage
VID ≤ −5.0 mV, IO = 50 mA, TA = 25°C
VID ≤−10 mV, IO = 50 mA, TA = 25°C
VCC ≥ 4.5 V, VEE = 0, Tlow ≤ TA ≤ Thigh*
VID 6≤6.0 mV, Isink ≤ 8.0 mA
VID 6≤10 mV, Isink ≤ 8.0 mA
VOL
Strobe ”On” Current (Note 5)
V
IS
Output Leakage Current
VID ≥ 5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID ≥ 10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA
VID ≥ 5.0 mV, VO= 35 V, Tlow ≤ TA ≤ Thigh*
Input Voltage Range (Tlow ≤ TA ≤ Thigh*)
* LM211: Tlow = −25°C, Thigh = +85°C
LM311: Tlow = 0°C, Thigh = +70°C
1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to ±15 V supplies.
2. This rating applies for ±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is
equal to the negative supply voltage or 30 V below the positive supply, whichever is less.
3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA
load. Thus, these parameters define an error band and take into account the “worst case” effects of voltage gain and input impedance.
4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.
5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.
8
VCC
Balance
Balance/Strobe
5
1.3k
300
6
300
1.3k
800
800
3.0k
100
3.7k
5.0k
3.7k
7
200
300
250
Output
900
600
800
1.3k
2
1
Inputs
3
730
1.3k
340
GND
5.4k
4
VEE
Figure 2. Circuit Schematic
http://onsemi.com
3
LM211, LM311
5.0
VCC = +15 V
VEE = -15 V
I IO , INPUT OFFSET CURRENT (nA)
I IB , INPUT BIAS CURRENT (nA)
140
120
Pins 5 & 6 Tied
to VCC
100
Normal
80
40
0
-55
-25
0
25
50
75
100
VCC = +15 V
VEE = -15 V
4.0
Pins 5 & 6 Tied
to VCC
3.0
2.0
1.0
Normal
0
-55
125
-25
0
25
50
75
TA, TEMPERATURE (°C)
TA, TEMPERATURE (°C)
Figure 3. Input Bias Current
versus Temperature
Figure 4. Input Offset Current
versus Temperature
100
125
100
125
VCC = +15 V
VEE = -15 V
TA = +25°C
VCC
COMMON MODE LIMITS (V)
120
100
80
60
40
20
Vin ,INPUT VOLTAGE (mV)
5.0
4.0
3.0
2.0
1.0
0
-12
-8.0
-4.0
0
4.0
8.0
12
-1.0
-1.5
0.4
0.2
VEE
-55
16
-25
0
25
50
75
TA, TEMPERATURE (°C)
Figure 5. Input Bias Current versus
Differential Input Voltage
Figure 6. Common Mode Limits
versus Temperature
5.0 mV
+5.0V
20 mV
Vin
500W
VO
*
)
2.0 mV
VCC = +15 V
VEE = -15 V
TA = +25°C
100
50
0
0
Referred to Supply Voltages
-0.5
DIFFERENTIAL INPUT VOLTAGE (V)
VO , OUTPUT VOLTAGE (V)
VO , OUTPUT VOLTAGE (V)
0
-16
0.1
0.2
0.3
0.4
tTLH, RESPONSE TIME (ms)
0.5
Vin ,INPUT VOLTAGE (mV)
I IB , INPUT BIAS CURRENT (nA)
140
0.6
Figure 7. Response Time for
Various Input Overdrives
+5.0V
5.0
4.0
3.0
2.0
1.0
0
2.0 mV
Vin
500W
*
)
VO
20 mV
VCC = +15 V
VEE = -15 V
TA = +25°C
0
-50
-100
http://onsemi.com
4
5.0 mV
0
0.1
0.2
0.3
0.4
tTHL, RESPONSE TIME (ms)
0.5
Figure 8. Response Time for
Various Input Overdrives
0.6
20 mV
VO , OUTPUT VOLTAGE (V)
15
10
5.0
0
-5.0
-10
-15
VCC
5.0 mV
Vin
*
)
VO
2.0k
Vin ,INPUT VOLTAGE (mV)
Vin ,INPUT VOLTAGE (mV)
VO , OUTPUT VOLTAGE (V)
LM211, LM311
VEE
2.0 mV
0
-50
VCC = +15 V
VEE = -15 V
TA = +25°C
-100
0
1.0
2.0
tTLH, RESPONSE TIME (ms)
VCC
15
10
5.0
0
-5.0
-10
-15
5.0 mV
20 mV
VCC = +15 V
VEE = -15 V
TA = +25°C
100
50
0
0
1.0
tTHL, RESPONSE TIME (ms)
125
0.75
Power Dissipation
0.60
75
0.45
Short Circuit Current
50
0.30
25
0.15
5.0
0.60
TA = -55°C
0.45
0.30
TA = +25°C
TA = +125°C
0.15
0
0
15
10
0.75
0
8.0
16
VO, OUTPUT VOLTAGE (V)
32
40
48
56
Figure 12. Output Saturation Voltage
versus Output Current
3.6
100
TA = +25°C
VCC = +15 V
VEE = -15 V
POWER SUPPLY CURRENT (mA)
OUTPUT LEAKAGE CURRENT (mA)
24
IO, OUTPUT CURRENT (mA)
Figure 11. Output Short Circuit Current
Characteristics and Power Dissipation
10
1.0
Output VO = +50 V (LM211 only)
0.1
0.01
25
2.0
0.90
PD , POWER DISSIPATION (W)
V , SATURATION VOLTAGE (V)
OL
OUTPUT SHORT CIRCUIT CURRENT (mA)
0.90
TA = +25°C
0
VO
2.0k
Figure 10. Response Time for
Various Input Overdrives
150
0
*
)
VEE
Figure 9. Response Time for
Various Input Overdrives
100
Vin
2.0 mV
3.0
Positive Supply - Output Low
2.4
1.8
Positive and Negative Power Supply - Output H igh
1.2
0.6
0
45
65
85
105
125
0
5.0
10
15
20
25
TA, TEMPERATURE (°C)
VCC-VEE, POWER SUPPLY VOLTAGE (V)
Figure 13. Output Leakage Current
versus Temperature
Figure 14. Power Supply Current
versus Supply Voltage
http://onsemi.com
5
30
LM211, LM311
SUPPLY CURRENT (mA)
3.0
VCC = +15 V
VEE = -15 V
2.6
Postive Supply - Output Low
2.2
1.8
Positive and Negative Supply - Output High
1.4
1.0
-55
-25
0
25
50
75
TA, TEMPERATURE (°C)
100
125
Figure 15. Power Supply Current
versus Temperature
APPLICATIONS INFORMATION
+15 V
+15 V
3.0 k
4.7 k
3.0 k
82
33 k
5.0 k
C1
0.1 mF
8
2
Input
+
R1
C2
4.7 k
0.002
6 mF
8
Input
5
LM311
1
R2
3
Output
7
100
R2
4
3.0 k
GND
GND
+
2
Output
7
4
0.1 mF
Output
to CMOS Logic
Output
Balance/Strobe
2N2222 or
Q1
Equivalent
1.0k
VEE
TTL
Strobe
VEE = -15 V
Figure 18. Zero−Crossing Detector
Driving CMOS Logic
VCC2
LM311
10 k
VCC
1
VCC
+
Inputs
+
LM311
5
LM311
VCC1
VEE
VCC = +15 V
Inputs
-
Figure 17. Conventional Technique
for Adding Hysteresis
VEE
Input
C1
-15 V 510 k
Figure 16. Improved Method of Adding
Hysteresis Without Applying Positive
Feedback to the Inputs
5.0 k
6
1.0 M
-15 V
Balance
3
R1
C2
100
0.1 mF
Balance
Adjust
5.0 k
0.1 mF
*D1
*Zener Diode D1
protects the comparator
from inductive kickback
and voltage transients
on the VCC2 supply line.
Figure 19. Relay Driver with Strobe Capability
http://onsemi.com
6
LM211, LM311
TECHNIQUES FOR AVOIDING OSCILLATIONS IN COMPARATOR APPLICATIONS
When a high speed comparator such as the LM211 is used
with high speed input signals and low source impedances,
the output response will normally be fast and stable,
providing the power supplies have been bypassed (with
0.1 mF disc capacitors), and that the output signal is routed
well away from the inputs (Pins 2 and 3) and also away from
Pins 5 and 6.
However, when the input signal is a voltage ramp or a slow
sine wave, or if the signal source impedance is high (1.0 kW
to 100 kW), the comparator may burst into oscillation near
the crossing−point. This is due to the high gain and wide
bandwidth of comparators like the LM211 series. To avoid
oscillation or instability in such a usage, several precautions
are recommended, as shown in Figure 16.
The trim pins (Pins 5 and 6) act as unwanted auxiliary
inputs. If these pins are not connected to a trim−pot, they
should be shorted together. If they are connected to a
trim−pot, a 0.01 mF capacitor (C1) between Pins 5 and 6 will
minimize the susceptibility to AC coupling. A smaller
capacitor is used if Pin 5 is used for positive feedback as in
Figure 16. For the fastest response time, tie both balance pins
to VCC.
Certain sources will produce a cleaner comparator output
waveform if a 100 pF to 1000 pF capacitor (C2) is connected
directly across the input pins. When the signal source is
applied through a resistive network, R1, it is usually
advantageous to choose R2 of the same value, both for DC
and for dynamic (AC) considerations. Carbon, tin−oxide,
and metal−film resistors have all been used with good results
in comparator input circuitry, but inductive wirewound
resistors should be avoided.
When comparator circuits use input resistors (e.g.,
summing resistors), their value and placement are particularly
important. In all cases the body of the resistor should be close
to the device or socket. In other words, there should be a very
short lead length or printed−circuit foil run between
comparator and resistor to radiate or pick up signals. The
same applies to capacitors, pots, etc. For example, if R1 =
10 kW, as little as 5 inches of lead between the resistors and
the input pins can result in oscillations that are very hard to
dampen. Twisting these input leads tightly is the best
alternative to placing resistors close to the comparator.
Since feedback to almost any pin of a comparator can
result in oscillation, the printed−circuit layout should be
engineered thoughtfully. Preferably there should be a
groundplane under the LM211 circuitry (e.g., one side of a
double layer printed circuit board). Ground, positive supply
or negative supply foil should extend between the output and
the inputs to act as a guard. The foil connections for the
inputs should be as small and compact as possible, and
should be essentially surrounded by ground foil on all sides
to guard against capacitive coupling from any fast
high−level signals (such as the output). If Pins 5 and 6 are not
used, they should be shorted together. If they are connected
to a trim−pot, the trim−pot should be located no more than
a few inches away from the LM211, and a 0.01 mF capacitor
should be installed across Pins 5 and 6. If this capacitor
cannot be used, a shielding printed−circuit foil may be
advisable between Pins 6 and 7. The power supply bypass
capacitors should be located within a couple inches of the
LM211.
A standard procedure is to add hysteresis to a comparator
to prevent oscillation, and to avoid excessive noise on the
output. In the circuit of Figure 17, the feedback resistor of
510 kW from the output to the positive input will cause about
3.0 mV of hysteresis. However, if R2 is larger than 100 W,
such as 50 kW, it would not be practical to simply increase
the value of the positive feedback resistor proportionally
above 510 kW to maintain the same amount of hysteresis.
When both inputs of the LM211 are connected to active
signals, or if a high−impedance signal is driving the positive
input of the LM211 so that positive feedback would be
disruptive, the circuit of Figure 16 is ideal. The positive
feedback is applied to Pin 5 (one of the offset adjustment
pins). This will be sufficient to cause 1.0 mV to 2.0 mV
hysteresis and sharp transitions with input triangle waves
from a few Hz to hundreds of kHz. The positive−feedback
signal across the 82 W resistor swings 240 mV below the
positive supply. This signal is centered around the nominal
voltage at Pin 5, so this feedback does not add to the offset
voltage of the comparator. As much as 8.0 mV of offset
voltage can be trimmed out, using the 5.0 kW pot and 3.0 kW
resistor as shown.
http://onsemi.com
7
LM211, LM311
PACKAGE DIMENSIONS
PDIP−8
N SUFFIX
CASE 626−05
ISSUE M
D
A
D1
E
8
5
E1
1
4
NOTE 5
F
c
E2
END VIEW
TOP VIEW
NOTE 3
e/2
A
L
A1
C
SEATING
PLANE
E3
e
8X
SIDE VIEW
b
0.010
M
C A
END VIEW
http://onsemi.com
8
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSION E IS MEASURED WITH THE LEADS RESTRAINED PARALLEL AT WIDTH E2.
4. DIMENSION E1 DOES NOT INCLUDE MOLD FLASH.
5. ROUNDED CORNERS OPTIONAL.
DIM
A
A1
b
C
D
D1
E
E1
E2
E3
e
L
INCHES
NOM
MAX
−−−− 0.210
−−−− −−−−
0.018 0.022
0.010 0.014
0.365 0.400
−−−− −−−−
0.310 0.325
0.250 0.280
0.300 BSC
−−−−
−−−− 0.430
0.100 BSC
0.115 0.130 0.150
MIN
−−−−
0.015
0.014
0.008
0.355
0.005
0.300
0.240
MILLIMETERS
MIN
NOM
MAX
−−−−
−−−−
5.33
0.38
−−−− −−−−
0.35
0.46
0.56
0.20
0.25
0.36
9.02
9.27 10.02
0.13
−−−− −−−−
7.62
7.87
8.26
6.10
6.35
7.11
7.62 BSC
−−−−
−−−− 10.92
2.54 BSC
2.92
3.30
3.81
LM211, LM311
PACKAGE DIMENSIONS
SOIC−8
D SUFFIX
CASE 751−07
ISSUE AK
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LM211/D