LV8713T D

Ordering number : ENA1918
LV8713T
Bi-CMOS LSI
PWM Constant-Current Control
Stepping Motor Driver
http://onsemi.com
Overview
The LV8713T is a stepping motor driver of the micro-step drive corresponding to supports 8W 1-2 phase excitation. It
is the best for the drive of the stepping motor for a scanner and a small printer.
Features
• Single-channel PWM constant-current control stepping motor driver incorporated.
• Control mode can be set to 2-phase, 1-2 phase, 4W1-2 phase , or 8W1-2 phase
• Microstep can control easily by the CLK-IN input.
• Power-supply voltage of motor
: VM max = 18V
• Output current
: IO max = 0.8A
• Output ON resistance
: RON = 1.1Ω (upper and lower total, typical, Ta = 25°C )
• A thermal shutdown circuit and a low voltage detecting circuit are built into.
Specifications
Absolute Maximum Ratings at Ta = 25°C
Parameter
Symbol
Motor supply voltage
VM max
Logic supply voltage
VCC max
Output peak current
IO peak
Output continuousness current
IO max
Logic input voltage
VIN
Allowable power dissipation
Pd max
Operating temperature
Storage temperature
Conditions
Ratings
Unit
18
V
6
V
Each 1ch, tw ≤ 10ms, duty 20%
1.0
A
Each 1ch
800
mA
-0.3 to VCC + 0.3
V
1.35
W
Topr
-20 to +85
°C
Tstg
-55 to +150
°C
*
* Specified circuit board : 57.0mm×57.0mm×1.7mm, glass epoxy 2-layer board.
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
Semiconductor Components Industries, LLC, 2013
June, 2013
20211 SY 20110117-S00002 No.A1918-1/16
LV8713T
Allowable Operating Ratings at Ta = 25°C
Parameter
Symbol
Motor supply voltage range
VM
Logic supply voltage range
VCC
Logic input voltage
VIN
VREF input voltage range
VREF
Conditions
Ratings
Unit
4 to 16
V
2.7 to 5.5
V
-0.3 tp VCC+0.3
V
0 to VCC-1.8
V
Electrical Characteristics at Ta = 25°C, VM = 12V, VCC = 3.3VVREF = 1.0V
Parameter
Symbol
Ratings
Conditions
min
Standby mode current drain
Current drain
typ
IMstn
PS = “L”, no load
1
μA
ICCstn
PS = “L”, no load
1
μA
IM
PS = “H”, no load
0.3
0.5
0.7
mA
0.9
1.3
1.7
mA
ICC
PS = “H”, no load
Thermal shutdown temperature
TSD
Design guarantee
180
Thermal hysteresis width
ΔTSD
Design guarantee
40
VCC low voltage cutting voltage
VthVCC
Low voltage hysteresis voltage
VthHIS
REG5 output voltage
Vreg5
IO = -1mA
Output on resistance
RonU
°C
°C
2.1
2.4
2.7
V
100
130
160
mV
4.5
5
5.5
V
IO = -800mA, Source-side on resistance
0.78
1.0
Ω
0.32
0.43
Ω
10
μA
1.0
1.2
V
RonD
IO = 800mA, Sink-side on resistance
Output leakage current
IOleak
VO = 15V
Diode forward voltage
VD
ID = -800mA
Logic pin input current
Unit
max
IINL
VIN = 0.8V
4
8
12
μA
IINH
VIN = 3.3V
22
33
45
μA
Logic high-level input voltage
VINH
Logic low-level input voltage
VINL
VREF input current
IREF
VREF = 1.0V
Current setting comparator
Vtatt00
ATT1 = L, ATT2 = L
0.191
0.200
0.209
threshold voltage
Vtatt01
ATT1 = H, ATT2 = L
0.152
0.160
0.168
V
Vtatt10
ATT1 = L, ATT2 = H
0.112
0.120
0.128
V
Vtatt11
ATT1 = H, ATT2 = H
0.072
0.080
0.088
V
Fchop
Cchop = 220pF
36
45
54
(current attenuation rate switching)
Chopping frequency
CHOP pin threshold voltage
2.0
V
0.8
V
μA
-0.5
V
kHz
VCHOPH
0.6
0.7
0.8
V
VCHOPL
0.17
0.2
0.23
V
7
10
13
μA
250
400
0.191
0.200
0.209
V
CHOP pin charge/discharge current
Ichop
MONI pin saturation voltage
Vsatmon
Imoni = 1mA
Current setting
8W1-2-phase
Vtdac0_2W
Step 0 (When initialized : channel 1
comparator
drive
threshold
Vtdac1_8W
Step 1 (Initial state+1)
0.191
0.200
0.209
V
voltage
Vtdac2_8W
Step 2 (Initial state+2)
0.191
0.200
0.209
V
Vtdac3_8W
Step 3 (Initial state+3)
0.189
0.198
0.207
V
Vtdac4_8W
Step 4 (Initial state+4)
0.187
0.196
0.205
V
Vtdac5_8W
Step 5 (Initial state+5)
0.185
0.194
0.203
V
Vtdac6_8W
Step 6 (Initial state+6)
0.183
0.192
0.201
V
Vtdac7_8W
Step 7 (Initial state+7)
0.179
0.188
0.197
V
Vtdac8_8W
Step 8 (Initial state+8)
0.175
0.184
0.193
V
Vtdac9_8W
Step 9 (Initial state+9)
0.171
0.180
0.189
V
Vtdac10_8W
Step 10 (Initial state+10)
0.167
0.176
0.185
V
Vtdac11_8W
Step 11 (Initial state+11)
0.163
0.172
0.181
V
Vtdac12_8W
Step 12 (Initial state+12)
0.158
0.166
0.174
V
Vtdac13_8W
Step 13 (Initial state+13)
0.152
0.160
0.168
V
Vtdac14_8W
Step 14 (Initial state+14)
0.146
0.154
0.162
V
Vtdac15_8W
Step 15 (Initial state+15)
0.140
0.148
0.156
V
Vtdac16_8W
Step 16 (Initial state+16)
0.132
0.140
0.148
V
(current step
switching)
mV
comparator level)
Continued on next page.
No.A1918-2/16
LV8713T
Continued from preceding page.
Parameter
Symbol
Ratings
Conditions
min
typ
Unit
max
Current setting
8W1-2-phase
Vtdac17_8W
Step 17 (Initial state+17)
0.126
0.134
0.142
V
comparator
drive
Vtdac18_8W
Step 18 (Initial state+18)
0.118
0.126
0.134
V
Vtdac19_8W
Step 19 (Initial state+19)
0.112
0.120
0.128
V
Vtdac20_8W
Step 20 (Initial state+20)
0.102
0.110
0.118
V
Vtdac21_8W
Step 21 (Initial state+21)
0.094
0.102
0.110
V
Vtdac22_8W
Step 22 (Initial state+22)
0.086
0.094
0.102
V
Vtdac23_8W
Step 23 (Initial state+23)
0.078
0.086
0.094
V
Vtdac24_8W
Step 24 (Initial state+24)
0.068
0.076
0.084
V
Vtdac25_8W
Step 25 (Initial state+25)
0.060
0.068
0.076
V
Vtdac26_8W
Step 26 (Initial state+26)
0.050
0.058
0.066
V
Vtdac27_8W
Step 27 (Initial state+27)
0.040
0.048
0.056
V
Vtdac28_8W
Step 28 (Initial state+28)
0.032
0.040
0.048
V
Vtdac29_8W
Step 29 (Initial state+29)
0.022
0.030
0.038
V
Vtdac30_8W
Step 30 (Initial state+30)
0.012
0.020
0.028
V
Vtdac31_8W
Step 31 (Initial state+31)
0.002
0.010
0.018
V
Vtdac0_4W
Step 0 (When initialized : channel 1
0.191
0.200
0.209
V
threshold
voltage
(current step
switching)
4W1-2-phase
drive
1-2 phase drive
comparator level)
Vtdac2_4W
Step 2 (Initial state+1)
0.191
0.200
0.209
V
Vtdac4_4W
Step 4 (Initial state+2)
0.187
0.196
0.205
V
Vtdac6_4W
Step 6 (Initial state+3)
0.183
0.192
0.201
V
Vtdac8_4W
Step 8 (Initial state+4)
0.175
0.184
0.193
V
Vtdac10_4W
Step 10 (Initial state+5)
0.167
0.176
0.185
V
Vtdac12_4W
Step 12 (Initial state+6)
0.158
0.166
0.174
V
Vtdac14_4W
Step 14 (Initial state+7)
0.146
0.154
0.162
V
Vtdac16_4W
Step 16 (Initial state+8)
0.132
0.140
0.148
V
Vtdac18_4W
Step 18 (Initial state+9)
0.118
0.126
0.134
V
Vtdac20_4W
Step 20 (Initial state+10)
0.102
0.110
0.118
V
Vtdac22_4W
Step 22 (Initial state+11)
0.086
0.094
0.102
V
Vtdac24_4W
Step 24 (Initial state+12)
0.068
0.076
0.084
V
Vtdac26_4W
Step 26 (Initial state+13)
0.050
0.058
0.066
V
Vtdac28_4W
Step 28 (Initial state+14)
0.032
0.040
0.048
V
Vtdac30_4W
Step 30 (Initial state+15)
0.012
0.020
0.028
V
Vtdac0_H
Step 0 (When initialized : channel 1
0.191
0.200
0.209
V
comparator level)
2 phase drive
Vtdac16_H
Step 4 (Initial state+1)
0.132
0.140
0.148
V
Vtdac16_F
Step 4' (When initialized : channel 1
0.191
0.200
0.209
V
comparator level)
No.A1918-3/16
LV8713T
Package Dimensions
unit : mm (typ)
3260A
6.5
0.5
6.4
13
4.4
24
12
1
0.5
0.15
0.22
1.2max
0.08
(1.0)
(0.5)
SANYO : TSSOP24(225mil)
Pd max - Ta
1.5
Allowable power dissipation, Pd max - W
1.35
1.0
0.70
0.5
Specified circuit board :
57.0 × 57.0 × 1.7mm3
2-layer glass epoxy board
0
- 20
0
20
40
60
80
100
Ambient temperature, Ta - C
FR
OUT1A
PGND
RNF1
OUT1B
VM
OUT2A
RNF2
OUT2B
PGND
MD1
MD2
Pin Assignment
24
23
22
21
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
9
10
11
12
RST
OE
REG5
PS
MONI
VREF
STEP
ATT1
ATT2
CHOP
VCC
GND
LV8713T
No.A1918-4/16
+
-
+
-
GND
VREF
VCC
REG5
LVS
TSD
+
-
PS
Start
circuit
Attenuator
(100%/80%
/50%/20%)
CHOP ATT1 ATT2
Oscillation
circuit
1/5
Standard
voltage
VM-5V
standard voltage
OUT1B
Current
selection
(8W1-2/
4W1-2/1-2/2)
+
OUT1A
Output preamplifier stage
Output preamplifier stage
MD1
MD2
FR
+
RNF2
Current
selection
(8W1-2/
4W1-2/1-2/2)
OUT2B
STEP RST OE
OUT2A
Output control logic
Output preamplifier stage
VM
Output preamplifier stage
RNF1
MONI
PGND
LV8713T
Block Diagram
No.A1918-5/16
LV8713T
Pin Functions
Pin No.
Pin Name
Pin Functtion
1
RST
Excitation reset signal input pin.
2
OE
Output enable signal input pin.
7
STEP
STEP signal input pin.
8
ATT1
Motor holding current switching pin.
9
ATT2
Motor holding current switching pin.
13
MD2
Excitation mode switching pin 2.
14
MD1
Excitation mode switching pin 1.
24
FR
CW / CCW switching signal input pin.
Equivalent Circuit
VCC
GND
4
PS
Power save signal input pin.
VCC
4
GND
16
OUT2B
Channel 2 OUTB output pin.
17
RNF2
Channel 2 current-sense resistor
18
OUT2A
Channel 2 OUTA output pin.
20
OUT1B
Channel 1 OUTB output pin.
21
RNF1
Channel 1 current-sense resistor
VM
connection pin.
20 16
23 18
connection pin.
23
OUT1A
Channel 1 OUTA output pin.Power
21
17
GND
6
VREF
Constant current control reference
voltage input pin.
VCC
6
GND
Continued on next page.
No.A1918-6/16
LV8713T
Continued from preceding page.
Pin No.
3
Pin Name
REG5
Pin Functtion
Internal power supply capacitor
connection pin.
Equivalent Circuit
VM
3
GND
5
MONI
Position detection monitor pin.
VCC
5
GND
10
CHOP
Chopping frequency setting capacitor
connection pin.
VCC
GND
10
No.A1918-7/16
LV8713T
Description of operation
Stepping motor control
(1) Power save function
This IC is switched between standby and operating mode by setting the PS pin. In standby mode, the IC is set to
power-save mode and all logic is reset. In addition, the internal regulator circuit do not operate in standby mode.
PS
Mode
Internal regulator
Low or Open
Standby mode
Standby
High
Operating mode
Operating
(2) The order of turning on recommended power supply
The order of turning on each power supply recommends the following.
VCC power supply order → VM power supply order → PS pin = High
It becomes the above-mentioned opposite for power supply OFF.
However, the above-mentioned is a recommendation, the overcurrent is not caused by not having defended this, and
IC is destroyed.
(3) STEP pin function
Operating mode
Input
PS
STP
Low
*
Standby mode
High
Excitation step proceeds
High
Excitation step is kept
(4) Excitation mode setting function(initial position)
MD1
MD2
Excitation mode
Initial position
Channel 1
Channel 2
-100%
Low
Low
2 phase excitation
100%
High
Low
1-2 phase excitation
100%
0%
Low
High
4W1-2 phase excitation
100%
0%
High
High
8W1-2 phase excitation
100%
0%
This is the initial position of each excitation mode in the initial state after power-on and when the counter is reset.
(5) Position detection monitoring function
The MONI position detection monitoring pin is of an open drian type.
When the excitation position is in the initial position, the MONI output is placed in the ON state.
(Refer to "(12) Examples of current waveforms in each of the excitation modes.")
No.A1918-8/16
LV8713T
(6) Reset function
RST
Operating mode
High
Normal operation
Low
Reset state
RST
RESET
STEP
MONI
1ch output
0%
2ch output
Initial position
When the RST pin is set to Low, the excitation position of the output is forcibly set to the initial position, and the
MONI output is placed in the ON state. When RST is then set to High, the excitation position is advanced by the next
STEP input.
(7) Output enable function
OE
Operating mode
Low
Output ON
High
Output OFF
OE
Power save mode
STEP
MONI
1ch output
0%
2ch output
Output is high-impedance
When the OE pin is set High, the output is forced OFF and goes to high impedance.
However, the internal logic circuits are operating, so the excitation position proceeds when the STEP signal is input.
Therefore, when OE is returned to Low, the output level conforms to the excitation position proceeded by the STEP input.
No.A1918-9/16
LV8713T
(8) Forward/reverse switching function
FR
Operating mode
Low
Clockwise (CW)
High
Counter-clockwise (CCW)
FR
CW mode
CCW mode
CW mode
STEP
Excitation position
(1)
(2)
(3)
(4)
(5)
(6)
(5)
(4)
(3)
(4)
(5)
1ch output
2ch output
The internal D/A converter proceeds by one bit at the rising edge of the input STEP pulse.
In addition, CW and CCW mode are switched by setting the FR pin.
In CW mode, the channel 2 current phase is delayed by 90° relative to the channel 1 current.
In CCW mode, the channel 2 current phase is advanced by 90° relative to the channel 1 current.
(9) Setting constant-current control
The setting of STM driver's constant current control is decided the VREF voltage from the resistance connected
between RNF and GND by the following expression.
IOUT = (VREF/5)/RNF resistance
* The above setting is the output current at 100% of each excitation mode.
The voltage input to the VREF pin can be switched to four-step settings depending on the statuses of the two inputs,
ATT1 and ATT2. This is effective for reducing power consumption when motor holding current is supplied.
Attenuation function for VREF input voltage
ATT1
ATT2
Current setting reference voltage attenuation ratio
Low
Low
100%
High
Low
80%
Low
High
60%
High
High
40%
The formula used to calculate the output current when using the function for attenuating the VREF input voltage is
given below.
IOUT = (VREF/5) × (attenuation ratio)/RNF resistance
Example : At VREF of 1.0V, a reference voltage setting of 100% [(ATT1, ATT2) = (L, L)] and an RNF resistance of
0.5Ω, the output current is set as shown below.
IOUT = 1.0V/5 × 100%/0.5Ω = 400mA
If, in this state, (ATT1, ATT2) is set to (H, H), IOUT will be as follows :
IOUT = 400mA × 40% = 160mA
In this way, the output current is attenuated when the motor holding current is supplied so that power can
be conserved.
No.A1918-10/16
LV8713T
(10) Chopping frequency setting
For constant-current control, this IC performs chopping operations at the frequency determined by the capacitor
(Cchop) connected between the CHOP pin and GND.
The chopping frequency is set as shown below by the capacitor (Cchop) connected between the CHOP pin and GND.
Tchop
C × V × 2 / I (s)
V : Width of suresshu voltage, typ 0.5V
I : Charge/discharge current, typ 10μA
For instance, when Cchop is 200pF, the chopping frequency will be as follows :
Fchop
1 / Tchop (Hz)
(11) Output current vector locus (one step is normalized to 90 degrees)
Channel 1 phase current ratio (%)
100.0
66.7
33.3
0.0
0.0
33.3
66.7
100.0
Channel 2 current ratio (%)
No.A1918-11/16
LV8713T
Setting current ration in each excitation mode
STEP
8W1-2 phase (%)
Channel 1
4W1-2 phase (%)
Channel 2
Channel 1
θ0
100
0
θ1
100
5
θ2
100
10
θ3
99
15
θ4
98
20
θ5
97
24
θ6
96
29
θ7
94
34
θ8
92
38
θ9
90
43
θ10
88
47
θ11
86
51
θ12
83
55
θ13
80
60
θ14
77
63
θ15
74
67
θ16
70
70
θ17
67
74
θ18
63
77
θ19
60
80
θ20
55
83
θ21
51
86
θ22
47
88
θ23
43
90
θ24
38
92
θ25
34
94
θ26
29
96
θ27
24
97
θ28
20
98
θ29
15
99
θ30
10
100
θ31
5
100
θ32
0
100
1-2 phase (%)
Channel 2
Channel 1
100
0
100
10
98
20
96
29
92
38
88
47
83
55
77
63
70
70
63
77
55
83
47
88
38
92
29
96
20
98
10
100
0
100
2-phase (%)
Channel 2
Channel 1
100
0
70
70
0
100
100
Channel 2
100
No.A1918-12/16
LV8713T
(12) Typical current waveform in each excitation mode
2-phase excitation (CW mode)
STEP
MONI
(%)
100
l1
0
-100
(%)
100
I2
0
-100
1-2 phase excitation (CW mode)
STEP
MONI
(%)
100
I1
0
-100
(%)
100
I2
0
-100
No.A1918-13/16
LV8713T
4W1-2 phase excitation (CW mode)
STEP
MONI
(%)
100
50
I1
0
-50
-100
(%)
100
50
I2
0
-50
-100
8W1-2 phase excitation (CW mode)
STEP
MONI
(%)
100
50
I1
0
-50
-100
(%)
100
50
I2
0
-50
-100
No.A1918-14/16
LV8713T
(13) Current control timing chart(Chopping operation)
(Sine wave increasing direction)
STEP
Set current
Set current
Coil current
Chopping cycle
fchop
BLANKING section
BLANKING section
Current mode CHARGE
SLOW
FAST
CHARGE
SLOW
FAST
(Sine wave decreasing direction)
STEP
Set current
Coil current
Set current
Chopping cycle
fchop
Current mode CHARGE
Chopping cycle
BLANKING section
SLOW
FAST
BLANKING section
Forced CHARGE
section
FAST
CHARGE
BLANKING section
SLOW
In each current mode, the operation sequence is as described below :
• At rise of chopping frequency, the CHARGE mode begins. (The Blanking section in which the CHARGE mode is
forced regardless of the magnitude of the coil current (ICOIL) and set current (IREF) exists for 1μs.)
• The coil current (ICOIL) and set current (IREF) are compared in this blanking time.
When (ICOIL < IREF) state exists ;
The CHARGE mode up to ICOIL ≥ IREF, then followed by changeover to the SLOW DECAY mode, and
finally by the FAST DECAY mode for approximately 1μs.
When (ICOIL < IREF) state does not exist ;
The FAST DECAY mode begins. The coil current is attenuated in the FAST DECAY mode till one cycle of
chopping is over.
Above operations are repeated. Normally, the SLOW (+FAST) DECAY mode continues in the sine wave increasing
direction, then entering the FAST DECAY mode till the current is attenuated to the set level and followed by the SLOW
DECAY mode.
No.A1918-15/16
LV8713T
Application Circuit Example
Logic input
- +
1.0V
Clock input
24
OUT1A
23
REG5
PGND
22
4
PS
RNF1
21
5
MONI
OUT1B
20
6
VREF
VM
19
7
STEP
8
ATT1
RNF2
17
9
ATT2
OUT2B
16
10
CHOP
PGND
15
11
VCC
MD1 14
12
GND
MD2
RST
2
OE
3
LV8713T
Short-circuit state
detection monitor
FR
1
Logic input
+ -
12V
OUT2A 18
M
220pF
3.3V
- +
Logic input
13
The formulae for setting the constants in the examples of the application circuits above are as follows :
Constant current (100%) setting
When VREF = 1.0V
IOUT = VREF/5/RNF resistance
= 1.0V/5/0.51Ω = 0.392A
Chopping frequency setting
Fchop = Ichop/ (Cchop × Vtchop × 2)
= 10μA/ (220pF × 0.5V × 2) = 45kHz
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A1918-16/16