TOSHIBA TB6613FTG

TB6613FTG
TOSHIBA BiCD Integrated Circuit
Silicon Monolithic
TB6613FTG
DC and Stepping Motor Driver
The TB6613FTG is a DC motor driver IC using LDMOS output
transistors with low ON-resistance.
The TB6613FTG incorporates five PWM constant-current
H-bridge drivers, of which four drivers can be used for micro
stepping motor drives of up to two stepping motors.
The TB6613FTG is best suited to control various lens actuators
in digital still cameras.
The three-wire serial interface provides control over the drivers,
thus reducing the number of lines required for interfacing with
the control IC.
Weight: 0.05 g (typ.)
Features
•
Motor power supply voltage: VM ≤ 6 V (max)
•
Control power supply voltage: VCC = 3 V to 5.5 V
•
Output current: IOUT ≤ 0.8 A (max)
•
Complementally P- and N-channel LDMOS output transistors
•
Output ON-resistance: RON (upper and lower sum) = 1.5 Ω (@VM = VCC = 5 V typ.)
Channels A, B, C and D
• Four H-bridge drivers capable of PWM constant-current control
Supports up to two two-phase bipolar stepping motors (STMs) or up to four actuators.
•
Each channel is individually configurable for either H-Bridge mode or STM μStep mode via the serial
interface.
•
In STM μStep mode, the micro stepping resolution is selectable from 6 bits (256 steps per full cycle) or 1 bit (8
steps per full cycle).
Channel E
• One PWM constant-current driver
•
The constant-current reference voltage (Vref) is programmable via the internal 6-bit DAC.
Other Features
• Each channel has a DAC for setting constant-current values (Channels A to D = 2 bits in H-Bridge mode and
2 bits × 6 bits in μStep mode; Channel E = 6 bits)
•
Dedicated standby (power-save) pin
•
Thermal shutdown (TSD)
•
Undervoltage lockout (UVLO): Resets and disables the internal circuitry when VCC falls below 2.2 V (typ.).
•
Small VQON44 package (0.4-mm lead pitch)
Note: This product has a MOS structure and is sensitive to electrostatic discharge. When handling this product,
ensure that the environment is protected against electrostatic discharge by using an earth strap, a
conductive mat and an ionizer. Ensure also that the ambient temperature and relative humidity are
maintained at reasonable levels.
1
2012-01-30
TB6613FTG
Block Diagram
CK
DATA
LD
GND
STBY
VCC
28
27
29
7
8
5
Standby
MCK 6
UVLO
(2.2 V)
12-bit serial
decoder
PWMA
33
/CK1
31 VM1
H-bridge
control
2-bit
DAC1
H-Bridge
A
36 AO1
34 AO2
PWM
timer
μStep
decoder 1
MO1 30
Predriver
35 RFA
6-bit
DAC
PWMB
32
/EN1
H-bridge
control
Predriver
H-Bridge
B
39 BO1
37 BO2
PWM
timer
38 RFB
1/N
PWMC
/CK2
25 VM2
H-bridge
control
23
2-bit
DAC2
H-Bridge
C
20 CO1
22 CO2
PWM
timer
μStep
decoder 2
MO2 26
Predriver
21 RFC
6-bit
DAC
PWMD
24
/EN2
H-bridge
control
Predriver
H-Bridge
D
17 DO1
19 DO2
PWM
timer
18 RFD
1/N
TSD
Vref
(0.3 V)
H-bridge
control
PWME 4
Predriver
H-Bridge
E
3 VM3
42 EO1
40 EO2
PWM
timer
6-bit
DAC
41 RFE
1/N
H-bridge
control
PWMF 2
Predriver
H-Bridge
F
1 FO1
43 FO2
44 PGND1
9 VM4
H-bridge
control
PWMG 10
Predriver
H-Bridge
G
15 GO1
16 GO2
14 PGND2
H-bridge
control
PWMH 11
2
Predriver
H-Bridge
H
12 HO1
13 HO2
2012-01-30
TB6613FTG
Pin Function
No.
Pin Name
I/O
Function
1
FO1
O
Channel-F output 1
2
PWMF
I
PWM signal input (Channel F)
3
VM3
―
4
PWME
I
5
VCC
―
6
MCK
I
7
GND
―
8
STBY
I
9
VM4
―
10
PWMG
I
PWM signal input (Channel G)
11
PWMH
I
PWM signal input (Channel H)
12
HO1
O
Channel-H output 1
Motor power supply 3 (Channels E and F)
PWM signal input (Channel E)
Power supply
Clock input for constant-current control
Ground
Standby (power-save) control
Motor power supply 4 (Channels G and H)
13
HO2
O
Channel-H output 2
14
PGND2
―
Motor ground 2 (Channels G and H)
15
GO1
O
Channel-G output 1
16
GO2
O
Channel-G output 2
17
DO1
O
Channel-D output 1
18
RFD
―
Connection pin for a current-sensing resistor (Channel D)
19
DO2
O
Channel-D output 2
20
CO1
O
Channel-C output 1
21
RFC
―
Connection pin for a current-sensing resistor (Channel C)
22
CO2
O
Channel-C output 2
23
PWMC/CK2
I
PWM signal input (Channel C)/μStep clock input 2
24
PWMD/EN2
I
PWM signal input (Channel D)/STM enable input 2
25
VM2
―
26
MO2
O
STM electrical degree monitor output 2, Open-drain output, need ext. pull-up resistor
27
DATA
I
Serial data input
28
CK
I
Serial clock input
Motor power supply 2 (Channels C and D)
29
LD
I
Serial load enable
30
MO1
O
STM electrical degree monitor output 1, Open-drain output, need ext. pull-up resistor
31
VM1
―
Motor power supply 1 (Channels A and B)
32
PWMB/EN1
I
PWM signal input (Channel B)/STM enable input 1
33
PWMA/CK1
I
PWM signal input (Channel A)/μStep clock input 1
34
AO2
O
Channel-A output 2
35
RFA
―
Connection pin for a current-sensing resistor (Channel A)
36
AO1
O
Channel-A output 1
37
BO2
O
Channel-B output 2
38
RFB
―
Connection pin for a current-sensing resistor (Channel B)
39
BO1
O
Channel-B output 1
40
EO2
O
Channel-E output 2
41
RFE
―
Connection pin for a current-sensing resistor (Channel E)
42
EO1
O
Channel-E output 1
43
FO2
O
Channel-F output 2
44
PGND1
―
Motor ground 1 (Channel F)
3
2012-01-30
TB6613FTG
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Symbol
Rating
Unit
Supply voltage
VCC
6
V
VCC
Motor supply voltage
VM
6
V
VM
VOUT
−0.2 to 6
V
Channels A to H
VMO
VCC
V
MO1, MO2 (Open-drain)
IOUT
0.8
A
Channels A to H
IMO
1
mA
Input voltage
VIN
−0.2 to 6
V
Control input pins
Power dissipation
PD
4.17
W
Note
Operating temperature
Topr
−20 to 85
°C
Storage temperature
Tstg
−55 to 150
°C
Output voltage
Output current
Remarks
MO1, MO2 (Open-drain)
Note: When mounted on a single-side glass epoxy PCB (size: 76.4 mm × 114.3 mm × 1.6 mm) with a 40%
dissipating copper surface.
Operating Conditions 1 (Ta = −20 to 85°C)
Characteristics
Symbol
Rating
Min
Typ.
Max
Unit
Supply voltage for small-signal
circuitry
VCC
3
3.3
5.5
V
Motor supply voltage
VM
2.5
―
5.5
V
―
―
600
―
―
250
Output current
IOUT
PWM frequency
fPWM
―
―
100
kHz
Master clock frequency
fMCK
―
1
5
MHz
4
mA
Remarks
VM = 3 to 5.5 V
2.2 V ≤ VM ≤ 3 V
2012-01-30
TB6613FTG
Operating Conditions 2: Serial Data Controller (Ta = −20°C to 85°C)
Characteristics
Symbol
Rating
Min
Max
Unit
Clock pulse width Low
tCKL
200
―
ns
Clock pulse width High
tCKH
200
―
ns
Clock rise time
tCr
―
50
ns
Clock fall time
tCf
―
50
ns
Data setup time
tDCH
30
―
ns
Data hold time
tCHD
60
―
ns
CK to LD rising edge
tCHL
200
―
ns
LD to PWM delay
tLDC2
100
―
ns
Load pulse width High
tLDH
2
―
μs
CK frequency
fCLK
―
2.5
MHz
tCr
tCKH
tCf
CK
tCKL
tCHD
DATA
tDCH
tCHL
tLDH
LD
Latch
tLDC2
PWM
5
2012-01-30
TB6613FTG
Principle of Operation
Bridge Outputs: Channels A through H
PWM Control
In PWM constant-current mode, the PWM chopper circuit alternates between on (t1, t5) and short brake
(t3).
(To eliminate shoot-through current, a dead time (t2, t4) of 50 ns (design target only) is inserted when the
PWM is turned on and off.)
VM
OUT1
VM
OUT2
M
OUT1
VM
OUT2
M
GND
OUT1
GND
<PWM: ON>
t1
<PWM: OFF>
t3
VM
M
OUT2
GND
<PWM: ON → OFF>
t2
OUT1
M
VM
OUT2
M
OUT1
GND
OUT2
GND
<PWM: OFF → ON>
t4
<PWM: ON>
t5
VM
t1
t5
Output voltage waveform
(OUT1)
t3
GND
t2
t4
6
2012-01-30
TB6613FTG
Constant current control on H-bridge driver; Off-time fixed PWM constant current
chopping operation
TB6613FTG operates Constant Current Control with off-time-fixed PWM operation.
The chop-off time is fixed by counting internally the external input driving clock, so the chop-off time could be
adjusted by changing the frequency of driving clock or the number of internal counting (2, 4, 6, 8 counts(4steps) are
selectable).
<Ex; Operation on four clock-counts>
First, motor coil current is generated on chop-on starting, and when the voltage (VRF) on external
current-sensing resistor rise and reach the reference voltage Vlimit (means current limit level) the current is to off
on comparator operation.
The chop-off time is fixed with 4bits of internal clock counting from the first rising edge of internal clock just after
the output high-side transistor is turned off.
(The counter is reset on the fifth rising edge of the internal clock)
This chop-off time control generates the PWM signal to drive On/Off the output transistors.
Timing Diagram of the PWM Constant-Current Chopper Circuit
with a Turn-Off Period of Four Clock Cycles
1 2 3 4 5 6
Counts 4 rising edges of internal clock.
Internal clock
Off timer
(counter)
Generated PWM
signal
Vlimit
Coil current
VRF
on
decay
on
decay
Power on
on
decay
on
Power off
(The upper limit of the coil current (IO peak) can be calculated as: IO = Vlimit/RNF.)
7
2012-01-30
TB6613FTG
Micro step Control: Channels A, B, C and D
In PWM constant-current mode, when the TB6613FTG generates a PWM signal, it measures a constant turn-off
period by counting the number of rising edges of the internal clock signal (divided clock of MCK).
PWMA PWMB
/CK1 /EN1 MO1
CK
DATA
LD
MCK
(1 MHz)
Serial
Decoder
5-bit
Divider
1/1 to
1/31
2-bit
DAC
PGND
CW/CCW,
Excitation Enable,
PWM
μstep decoder
6-bit DAC
Ph. B
VREF
(0.3 V)
VM
Ph. A
Predriver
64
64
63
63
62
62
2
2
Predriver
1
1
PWM
timer
H-bridge
A
M
Phase A
H-bridge
B
M
Phase B
PWM
timer
•
Pulse clock control: The TB6613FTG steps up the current at each rising edge of the clock input to the
PWMA/CK1 (for channels A and B) or PWMC/CK2 (for channels C and D) pin.
(Current step-ups actually occur synchronous to the internal clock signal derived from
MCK.)
•
μStep modes: Selectable from the following two modes:
1-bit mode: 8 steps per full cycle
6-bit mode: resolution = 256 steps per full cycle
•
Enable control: Setting PWMB/EN1 (for channels A and B) or PWMD/EN2 (for channels C and D) High and Low
enables and disables motor excitation.
ENn = 1: Excitation enabled; ENn = 0: Excitation disabled
•
Current decay modes: In STM μStep mode, the motor current recirculates back to the power supply in
Fast-Decay mode when the Vref level changes during current step-down. The current
decay rate is selectable from four modes.
•
Electrical degree monitor: As the output current increases or decreases in steps with the CK input, a negative
pulse is generated from the MO1 (or MO2) pin at every 90 or 360 electrical degrees.
•
PWM chopping frequency: The PWM signal is generated by dividing the external MCK signal by up to 31, as
programmed in a 5-bit register.
•
Turn-off period: The turn-off period is selectable from 2, 4, 6 and 8 cycles of the internal clock signal, which is
generated by dividing MCK internally.
8
2012-01-30
TB6613FTG
•
Constant-current setting:
The maximum Vref voltage can be selected from 0.3 V, 0.225 V, 0.15 V and 0.075
V with a 2-bit DAC based on the 0.3-V on-chip reference voltage.
This DAC output is divided by the 6-bit DAC under control of the micro step
decoder to establish Vref for constant-current control.
Current Decay Mode: Only Applicable for Step-Down Control in STM μStep Mode
In STM μStep mode, the output current step-down slope may not match the changes of the target current level
specified by Vref depending on the time constant of a motor coil, thus leading to a big distortion from the desired
output current waveform.
To improve the matching between the output current and the target current level, the TB6613FTG enters
Fast-Decay mode very briefly immediately after each Vref step-down. In this mode, the output current
recirculates back to the power supply.
The Fast-Decay time is generated by counting the internal clock signal and selectable from the four modes
listed below:
Fast-Decay Mode
Number of Internal Clock Cycle
Decay Rate
Fast0
0
No
Fast1
1
Small
Fast2
2
Medium
Fast3
3
Large
9
2012-01-30
TB6613FTG
Current Step-Up Slope
1
2
3
4
5
1
2
3
4
5
1
2
3
4
5
1
2
3
4
Internal
clock
Vref
Charge mode
Enters Charge mode at the Vref
step-up edge
Slow-Decay mode
Current Step-Down Slope (when in Fast1 mode)
1
2
3
4
5
1
2
3
4
5
1
2
1
2
3
4
5
1
2
3
Internal
clock
Vref
Charge mode
Slow-Decay mode
Enters Fast-Decay mode at the
Vref step-down edge
Fast-Decay mode
10
2012-01-30
TB6613FTG
Timing Diagram of Micro step Operation with 1-Bit Resolution (8 steps per full cycle)
CKn
MOn
init
MOn
quarter
100
71
φA
φB
IO (%)
0
−71
−100
Output Current Vector
1-2-Phase Excitation
100
IA (%)
71
0
0
71
IB
100
(%)
11
2012-01-30
TB6613FTG
Timing Diagram of Micro step Operation with 6-Bit Resolution (256 steps per full cycle)
0
64
128
192
128
192
CKn
MOn
init
MOn
quarter
100
90
80
70
60
50
40
30
φA
φB
20
10
IO (%) 0
−100
64
256
−20
−30
−40
−50
−60
−70
−80
−90
−10
12
2012-01-30
TB6613FTG
Relationship between the Enable and RESET Inputs and Output Signals
Enable (ENn Pin)
Reverse
Forward
CKn
ENn
RESET
MOn
(%)
100
71
IA
0
−71
−100
t0
t1
t2
t3
OFF
t7
t8
t9
t10
t11
t12
Setting the ENn signal Low disables only the output block, and the internal circuitry continues to operate in
accordance with the CKn input. Therefore, when the ENn signal is set High again, the output current
restarts as if phases had proceeded with the CKn signal.
When ENn = Low, the output signals are disabled regardless of the state of the RESET signal.
Setting the RESET signal Low while ENn = Low resets the counter.
RESET (Serial Command)
Reverse
Forward
CKn
ENABLE
RESET
MOn
(%)
100
71
IA
0
−71
−100
t0
t1
t2
t3
t2
t3
t4
t5
t6
t7
t8
Setting the RESET signal High causes the outputs to be put in the Initial state and the MOn output to be
driven Low.
When the RESET signal goes is set Low again, the output current generation restarts from the Initial state at
the next rising edge of CKn.
13
2012-01-30
TB6613FTG
Input Pins
All input pins (CK, DATA, LD, PWMA/CK1, PWMB/EN1, PWMC/CK2, PWMD/EN2, PWME, PWMF, PWMG,
PWMH, STBY, MCK) have a pull-down resister of about 200 kΩ.
Input
200 kΩ
GND
14
2012-01-30
TB6613FTG
Serial Data Format
12-Bit Serial Data
CK
DATA
LD
Latch
First
D11
Last
D10
D9
D8
D7
D6
D5
D4
Selector (4 bits)
D3
D2
D1
D0
Data
Register Organizations
D11
D10
D9
D8
D7
D6
D5
0
0
0
0
mod1
stm1
if1
0
0
0
1
0
0
1
0
p1a
p1b
0
0
1
1
mod2
p2a
p2b
0
1
0
0
mod3
stm3
if3
0
1
0
1
0
1
1
0
p3a
p3b
0
1
1
1
mod4
p4a
1
0
0
0
mod5
if5
1
0
0
1
1
0
1
0
p5a
p5b
―
―
―
―
―
―
10
1
0
1
1
mod6
p6a
p6b
―
―
―
―
―
11
1
1
0
0
mod7
p7a
p7b
―
―
―
―
―
12
1
1
0
1
mod8
p8a
p8b
―
―
―
―
―
13
1
1
1
0
1
1
1
1
2-bit DAC1
2-bit DAC2
off5
modx
: H-bridge control
stmx
: STM mode select
ifx
: Constant-current control
2-bit DACx : 2-bit DAC setting
ickx
mdrx
: Divide ratio for internal clock*
: STM excitation mode
D4
D3
D2
D1
D0
ick1: 5 bits
mdr1
rst1
sdfst1
mo1
if2
0
off1
scw1
―
off2
―
1
―
―
2
―
―
3
ick3: 5 bits
mdr3
rst3
Sdfst3
p4b
mo3
if4
4
off3
scw3
―
off4
―
5
―
―
6
―
―
7
6-bit DAC
―
8
ick5: 5 bits
Don’t access
Address
9
14
15
0 = Direct PWM mode (Table 1)
1 = Control mode of Table 2 (All channels)
0 = H-Bridge mode
1 = STM μStep mode (*)
0 = Constant-current control disabled
1 = Constant-current control enabled (Channels A, B, C, D
and E)
* Valid only in H-Bridge mode (stmx = 0). Constant-current
control is always enabled in STM μStep mode.
0 = 0.075 V; 1 = 0.15 V; 2 = 0.225 V; 3 = 0.3 V
4 levels in 0.075-V steps (*)
Divides the external MCK by 1 to 31. (*, channel E)
0 = μStep mode with 6-bit resolution
1 = 1-2-phase excitation mode (*)
15
2012-01-30
TB6613FTG
sdfstx
: Fast-Decay mode
scwx
rstx
mox
: STM rotation direction select
: STM step counter reset
: Monitor signal interval
offx
: PWM turn-off period
pxa
: H-bridge control input a
pxb
: H-bridge control input b
6-bit DAC : Channel-E 6-bit DAC setting*
Specifies the Fast-Decay time in number of internal clock
cycles: 0 = No Fast-Decay cycle; 1 = 1 cycle; 2 = 2 cycles;
3 = 3 cycles (*)
0 = Forward; 1 = Reverse (*)
0 = Count mode; 1 = Reset (*)
0 = Every 360 electrical degree
1 = Every 90 electrical degree (*)
Specifies the PWM turn-off period in number of internal clock
cycles: 0 = 2 cycles; 1 = 4 cycles; 2 = 6 cycles;
3 = 8 cycles (*, channel E)
See Tables 1 and 2 on next page (All channels)
See Tables 1 and 2 on next page (All channels)
MSB = 0.3 V (6 bits) (Channel E)
Note: Two registers at addresses 3 and 7 are only valid in H-Bridge mode (stmx = 0).
*: Detailed descriptions of register settings are provided in the tables on the following pages.
**: Do not access to address-14 or address-15 as these are for IC-testing in Toshiba.
16
2012-01-30
TB6613FTG
Supplemental Register Descriptions
1. Each channel or micro step pair is separately addressed.
Address
Corresponding Channels
0, 1, 2, 3
Channels A and B (stm1 = 1: micro step pair 1 (A&B))
4, 5, 6, 7
Channels C and D (stm3 = 1: micro step pair 2 (C&D))
8, 9, 10
Channel E
11
Channel F
12
Channel G
13
Channel H
Note: Two registers at addresses 3 (channel-B setting) and 7 (channel-D setting) are only valid in H-Bridge mode
(stmx = 0).
2. The character x in register names represents a channel number.
x
Corresponding Channels
x=1
Channel A (The settings of stmx, ickx, 2-bit DACx, mdrx, rstx, mox, sdfstx and scwx are shared between channels A
and B.)
x=2
Channel B
x=3
Channel C (The settings of stmx, ickx, 2-bit DACx, mdrx, rstx, mox, sdfstx and scwx are shared between channels
C and D.)
x=4
Channel D
x=5
Channel E
x=6
Channel F
x=7
Channel G
x=8
Channel H
17
2012-01-30
TB6613FTG
3. ickx: Setting the divide ratio for the external MCK used to generate the internal clock
The external MCK is divided to generate an internal clock, as specified for each channel (micro step pair) by
D4, D3, D2, D1 and D0 at addresses 0 (for channels A and B), 4 (for channels C and D) and 8 (for channel E).
Decimal
Binary
1
Address 0, 4 or 8
Divide Ratio for
Internal Clock
D4
D3
D2
D1
D0
00001
0
0
0
0
1
1/1
2
00010
0
0
0
1
0
1/2
3
00011
0
0
0
1
1
1/3
4
00100
0
0
1
0
0
1/4
5
00101
0
0
1
0
1
1/5
6
00110
0
0
1
1
0
1/6
7
00111
0
0
1
1
1
1/7
8
01000
0
1
0
0
0
1/8
9
01001
0
1
0
0
1
1/9
10
01010
0
1
0
1
0
1/10
11
01011
0
1
0
1
1
1/11
12
01100
0
1
1
0
0
1/12
13
01101
0
1
1
0
1
1/13
14
01110
0
1
1
1
0
1/14
15
01111
0
1
1
1
1
1/15
16
10000
1
0
0
0
0
1/16
17
10001
1
0
0
0
1
1/17
18
10010
1
0
0
1
0
1/18
19
10011
1
0
0
1
1
1/19
20
10100
1
0
1
0
0
1/20
21
10101
1
0
1
0
1
1/21
22
10110
1
0
1
1
0
1/22
23
10111
1
0
1
1
1
1/23
24
11000
1
1
0
0
0
1/24
25
11001
1
1
0
0
1
1/25
26
11010
1
1
0
1
0
1/26
27
11011
1
1
0
1
1
1/27
28
11100
1
1
1
0
0
1/28
29
11101
1
1
1
0
1
1/29
30
11110
1
1
1
1
0
1/30
31
11111
1
1
1
1
1
1/31
18
2012-01-30
TB6613FTG
4. 6-bit DAC: Setting the 6-bit DAC for channel E
The Vref voltage that determines the target current level for constant-current control of channel E can be
specified by D5, D4, D3, D2, D1 and D0 at address 8.
The target current level is determined by this voltage level and the external current sensing resistor.
Decimal
Binary
0
Address 8
Voltage
(mV)
D5
D4
D3
D2
D1
D0
000000
0
0
0
0
0
0
0.0
1
000001
0
0
0
0
0
1
4.8
2
000010
0
0
0
0
1
0
9.5
3
000011
0
0
0
0
1
1
14.3
4
000100
0
0
0
1
0
0
19.0
5
000101
0
0
0
1
0
1
23.8
6
000110
0
0
0
1
1
0
28.6
7
000111
0
0
0
1
1
1
33.3
8
001000
0
0
1
0
0
0
38.1
9
001001
0
0
1
0
0
1
42.9
10
001010
0
0
1
0
1
0
47.6
11
001011
0
0
1
0
1
1
52.4
12
001100
0
0
1
1
0
0
57.1
13
001101
0
0
1
1
0
1
61.9
14
001110
0
0
1
1
1
0
66.7
15
001111
0
0
1
1
1
1
71.4
16
010000
0
1
0
0
0
0
76.2
17
010001
0
1
0
0
0
1
81.0
18
010010
0
1
0
0
1
0
85.7
19
010011
0
1
0
0
1
1
90.5
20
010100
0
1
0
1
0
0
95.2
21
010101
0
1
0
1
0
1
100.0
22
010110
0
1
0
1
1
0
104.8
23
010111
0
1
0
1
1
1
109.5
24
011000
0
1
1
0
0
0
114.3
25
011001
0
1
1
0
0
1
119.0
26
011010
0
1
1
0
1
0
123.8
27
011011
0
1
1
0
1
1
128.6
28
011100
0
1
1
1
0
0
133.3
29
011101
0
1
1
1
0
1
138.1
30
011110
0
1
1
1
1
0
142.9
31
011111
0
1
1
1
1
1
147.6
32
100000
1
0
0
0
0
0
152.4
33
100001
1
0
0
0
0
1
157.1
34
100010
1
0
0
0
1
0
161.9
35
100011
1
0
0
0
1
1
166.7
36
100100
1
0
0
1
0
0
171.4
37
100101
1
0
0
1
0
1
176.2
38
100110
1
0
0
1
1
0
181.0
19
2012-01-30
TB6613FTG
Decimal
Binary
39
Address 8
Voltage
(mV)
D5
D4
D3
D2
D1
D0
100111
1
0
0
1
1
1
185.7
40
101000
1
0
1
0
0
0
190.5
41
101001
1
0
1
0
0
1
195.2
42
101010
1
0
1
0
1
0
200.0
43
101011
1
0
1
0
1
1
204.8
44
101100
1
0
1
1
0
0
209.5
45
101101
1
0
1
1
0
1
214.3
46
101110
1
0
1
1
1
0
219.0
47
101111
1
0
1
1
1
1
223.8
48
110000
1
1
0
0
0
0
228.6
49
110001
1
1
0
0
0
1
233.3
50
110010
1
1
0
0
1
0
238.1
51
110011
1
1
0
0
1
1
242.9
52
110100
1
1
0
1
0
0
247.6
53
110101
1
1
0
1
0
1
252.4
54
110110
1
1
0
1
1
0
257.1
55
110111
1
1
0
1
1
1
261.9
56
111000
1
1
1
0
0
0
266.7
57
111001
1
1
1
0
0
1
271.4
58
111010
1
1
1
0
1
0
276.2
59
111011
1
1
1
0
1
1
281.0
60
111100
1
1
1
1
0
0
285.7
61
111101
1
1
1
1
0
1
290.5
62
111110
1
1
1
1
1
0
295.2
63
111111
1
1
1
1
1
1
300.0
Note: The voltage values are typical values.
20
2012-01-30
TB6613FTG
Function Tables
The drive method in H-Bridge mode (stmx = 0) can be selected from Tables 1 and 2, via the modx bit.
(Channels E, F, G and H are always in H-Bridge mode regardless of the stmx setting.)
Table 1
modx = 0, stmx = 0
pxa
pxb
PWMx
OUTxA
OUTxB
Drive Mode
0
0
X
Z
Z
Stop
0
1
L
L
L
Short brake
0
1
H
L
H
Reverse
1
0
L
L
L
Short brake
1
0
H
H
L
Forward
1
1
X
L
L
Short brake
Table 2
modx = 1, stmx = 0
pxa
pxb
PWMx
OUTxA
OUTxB
Drive Mode
0
X
X
Z
Z
Stop
1
0
L
H
L
Forward
1
0
H
L
H
Reverse
1
1
X
L
L
Short brake
Function Table: STBY pin, UVLO and TSD circuitry, rstx bit (internal register)
Function
STBY (Note 1)
UVLO
TSD
rstx
Internal Register
Cleared
Cleared
Not affected
Not affected
Driver
Turned off
Turned off
Turned off
Turned on
(controlled by the ENn pin)
Note 1: STBY: L = Standby (power-save) mode; H = Normal operation mode
Note :
All registers are cleared to zero.
21
2012-01-30
TB6613FTG
Power supply sequence
The power supply sequence for TB6613FTG is required for proper operation.
The power up sequence between Vcc and VMx(x=1,2,3,4) is shown below.
Vcc
VMx
On
On
over 100ns
VMx(x=1,2,3,4) must be supplied after waiting over 100ns period from the Vcc is supplied.
If VMx are supplied without the waiting time or Vcc supply, IC could not start the normal operation
and go into some error mode in a case.
Data communication initialization Sequence
A proper initialization sequence is also needed for a host to communicate with TB6613FTG.
The initialization sequence is shown below.
22
2012-01-30
TB6613FTG
Electrical Characteristics (VCC = 3.3 V, VM = 5 V, Ta = 25°C, unless otherwise specified.)
Characteristics
Symbol
Min
Typ.
Max
Unit
―
2
4
mA
―
0.1
10
―
0
1
VINH
VCC ×
0.7
―
VCC +
0.2
VINL
−0.2
―
VCC ×
0.3
ICC
Supply current
ICC (STB)
IM (STB)
Serial, STBY,
PWM and CLK
inputs
Test Condition
All 8 channels in Forward mode
Standby mode (STBY = 0 V)
Input voltage
Input current
Output saturation voltage
(Channels A to H)
Output leakage current
(Channels A to H)
Output diode forward voltage
Voltage comparator offset for
constant-current control
Nonlinearity
IINH
VIH = 3 V
5
15
25
IINL
VIL = 0 V
―
―
1
IO = 0.2 A, VCC = 5 V
―
0.3
0.4
IO = 0.6 A, VCC = 5 V
―
0.9
1.2
―
―
1
―
―
1
―
1
―
―
1
―
−10
―
10
−3
―
3
−2
―
2
See Appendix on next page.
―
―
―
(Design target only)
―
71
―
―
2.0
―
―
2.2
―
―
170
―
―
20
―
Vsat (U + L)
IL (U)
IL (L)
VF (U)
VF (L)
Comp ofs
VM = 6 V
IF = 0.6 A (Design target only)
RF = 0.5 Ω,
Vref = 0.1 V (including DAC)
LB
6-bit DAC
Differential linearity
error
Micro step
reference level
6-bit mode
θ
1-bit mode
Half step
VCC under
voltage lockout
(UVLO)
UVLO trip
threshold
UVLD
UVLO recovery
UVLC
DLB
Thermal shutdown threshold
TSD
Thermal shutdown hysteresis
ΔTSD
Channel E
(Design target value)
(Design target only)
Delay between Vcc to VMx
Td1
(Design target only) Vcc, VM1,2,3,4
―
100
―
Delay between STBY=H to Serial
communication
Td2
(Design target only) STBY, CK, DATA, LD
―
100
―
μA
V
μA
V
μA
V
mV
LSB
%
V
°C
ns
23
2012-01-30
TB6613FTG
Appendix: Micro step Reference Level with 6-Bit Resolution (Design target only)
θ
Min
Typ.
Max
θ
Min
Typ.
Max
θ63
―
100
―
θ31
―
71
―
θ62
―
100
―
θ30
―
69
―
θ61
―
100
―
θ29
―
67
―
θ60
―
100
―
θ28
―
65
―
θ59
―
100
―
θ27
―
63
―
θ58
―
99.5
―
θ26
―
61.25
―
θ57
―
99
―
θ25
―
59.5
―
θ56
―
98.5
―
θ24
―
57.75
―
θ55
―
98
―
θ23
―
56
―
θ54
―
97.5
―
θ22
―
53.75
―
θ53
―
97
―
θ21
―
51.5
―
θ52
―
96.5
―
θ20
―
49.25
―
θ51
―
96
―
θ19
―
47
―
θ50
―
95
―
θ18
―
44.75
―
θ49
―
94
―
θ17
―
42.5
―
θ48
―
93
―
θ16
―
40.25
―
θ47
―
92
―
θ15
―
38
―
θ46
―
91
―
θ14
―
35.75
―
θ45
―
90
―
θ13
―
33.5
―
θ44
―
89
―
θ12
―
31.25
―
θ43
―
88
―
θ11
―
29
―
θ42
―
86.75
―
θ10
―
26.75
―
θ41
―
85.5
―
θ9
―
24.5
―
θ40
―
84.25
―
θ8
―
22.25
―
θ39
―
83
―
θ7
―
20
―
θ38
―
81.5
―
θ6
―
17.5
―
θ37
―
80
―
θ5
―
15
―
θ36
―
78.5
―
θ4
―
12.5
―
θ35
―
77
―
θ3
―
10
―
θ34
―
75.5
―
θ2
―
7.5
―
θ33
―
74
―
θ1
―
5
―
θ32
―
72.5
―
θ0
―
2.5
―
Unit
%
24
Unit
%
2012-01-30
TB6613FTG
Application Circuit Example
Vcc
3V to 5.5V
10uF +
C1
C2
0.1uF
CK
28
DATA
27
LD
29
GND
7
STBY
8
Vcc
5
STAND
BY
MCK
MCU
PW MA
/CK1
MO1
PW MB
/EN1
UVLO
(2.2V)
12bit Serial
Decoder
6
31
33
H-Bridge
Control
30
μStep
decorder
1
2bit
DAC1
6bit
DAC
32
H-Bridge
A
PreDriver
36
34
VM1
AO1
AO2
Step
Motor1
H-Bridge
Control
H-Bridge
B
PreDriver
39
37
R1=
0.5Ω
RFA
38
PW MC
/CK2
MO2
PW MD
/EN2
25
23
H-Bridge
Control
26
μStep
decorder
2
2bit
DAC2
6bit
DAC
24
H-Bridge
C
PreDriver
20
22
H-Bridge
Control
H-Bridge
D
PreDriver
17
19
R2=
0.5Ω
RFB
VM2
CO1
CO2
Step
Motor2
R3=
0.5Ω
RFC
DO1
DO2
PW M
Timer
18
1/N
TSD
Vref
(0.3V)
PW ME
H-Bridge
Control
4
6bit
DAC
PreDriver
3
H-Bridge
E
40
41
H-Bridge
Control
2
PreDriver
H-Bridge
F
1
43
44
9
PW MG
H-Bridge
Control
10
PreDriver
H-Bridge
G
15
16
14
PW MH
R4=
0.5Ω
RFD
VM3
EO1
EO2
Shutter
Coil
PW M
Timer
1/N
PW MF
42
H-Bridge
Control
11
25
PreDriver
H-Bridge
H
12
13
2.5V to
5.5V
BO1
PW M
Timer
21
0.1uF
BO2
PW M
Timer
1/N
VM
C4
10uF
PW M
Timer
35
C3 +
R5=
0.5Ω
RFE
FO1
FO2
DC
Motor1
PGND1
VM4
GO1
GO2
Step
Motor3
PGND2
HO1
HO2
2012-01-30
TB6613FTG
Package Dimensions
Weight: 0.05 g (typ.)
26
2012-01-30
TB6613FTG
Notes on Contents
1. Block Diagrams
Some of the functional blocks, circuits, or constants in the block diagram may be omitted or simplified for
explanatory purposes.
2. Equivalent Circuits
The equivalent circuit diagrams may be simplified or some parts of them may be omitted for explanatory
purposes.
3. Timing Charts
Timing charts may be simplified for explanatory purposes.
4. Application Circuits
The application circuits shown in this document are provided for reference purposes only. Thorough
evaluation is required, especially at the mass production design stage.
Toshiba does not grant any license to any industrial property rights by providing these examples of
application circuits.
5. Test Circuits
Components in the test circuits are used only to obtain and confirm the device characteristics. These
components and circuits are not guaranteed to prevent malfunction or failure from occurring in the
application equipment.
IC Usage Considerations
Notes on Handling of ICs
(1)
The absolute maximum ratings of a semiconductor device are a set of ratings that must not be
exceeded, even for a moment. Do not exceed any of these ratings.
Exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result
injury by explosion or combustion.
(2)
Use an appropriate power supply fuse to ensure that a large current does not continuously flow in case
of over current and/or IC failure. The IC will fully break down when used under conditions that exceed
its absolute maximum ratings, when the wiring is routed improperly or when an abnormal pulse noise
occurs from the wiring or load, causing a large current to continuously flow and the breakdown can
lead smoke or ignition. To minimize the effects of the flow of a large current in case of breakdown,
appropriate settings, such as fuse capacity, fusing time and insertion circuit location, are required.
(3)
If your design includes an inductive load such as a motor coil, incorporate a protection circuit into the
design to prevent device malfunction or breakdown caused by the current resulting from the inrush
current at power ON or the negative current resulting from the back electromotive force at power OFF.
IC breakdown may cause injury, smoke or ignition.
Use a stable power supply with ICs with built-in protection functions. If the power supply is unstable,
the protection function may not operate, causing IC breakdown. IC breakdown may cause injury,
smoke or ignition.
(4)
Do not insert devices in the wrong orientation or incorrectly.
Make sure that the positive and negative terminals of power supplies are connected properly.
Otherwise, the current or power consumption may exceed the absolute maximum rating, and
exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result
injury by explosion or combustion.
In addition, do not use any device that is applied the current with inserting in the wrong orientation or
incorrectly even just one time.
27
2012-01-30
TB6613FTG
Points to Remember on Handling of ICs
(1)
Over current Protection Circuit
Over current protection circuits (referred to as current limiter circuits) do not necessarily protect ICs
under all circumstances. If the Over current protection circuits operate against the over current, clear
the over current status immediately.
Depending on the method of use and usage conditions, such as exceeding absolute maximum ratings
can cause the over current protection circuit to not operate properly or IC breakdown before operation.
In addition, depending on the method of use and usage conditions, if over current continues to flow for
a long time after operation, the IC may generate heat resulting in breakdown.
(2)
Heat Radiation Design
In using an IC with large current flow such as power amp, regulator or driver, please design the device
so that heat is appropriately radiated, not to exceed the specified junction temperature (Tj) at any time
and condition. These ICs generate heat even during normal use. An inadequate IC heat radiation
design can lead to decrease in IC life, deterioration of IC characteristics or IC breakdown. In addition,
please design the device taking into considerate the effect of IC heat radiation with peripheral
components.
(3)
Back-EMF
When a motor rotates in the reverse direction, stops or slows down abruptly, a current flow back to the
motor’s power supply due to the effect of back-EMF. If the current sink capability of the power supply
is small, the device’s motor power supply and output pins might be exposed to conditions beyond
absolute maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in
system design.
28
2012-01-30
TB6613FTG
The following conditions apply to solderability:
About solderability, following conditions were confirmed
(1)Use of Sn-37Pb solder Bath
·solder bath temperature: 230°C·dipping time: 5 seconds·the number of times: once·use of R-type flux
(2)Use of Sn-3.0Ag-0.5Cu solder Bath
·solder bath temperature: 245°C·dipping time: 5 seconds·the number of times: once·use of R-type flux
29
2012-01-30
TB6613FTG
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the Product,
or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of all
relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for
Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the instructions for
the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their own product
design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or
applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams,
programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for
such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR APPLICATIONS.
• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public
impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the
aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
• Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation,
for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology
products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign
Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software
or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
30
2012-01-30