MC14001B D

MC14001B Series
B-Suffix Series CMOS Gates
MC14001B, MC14011B, MC14023B,
MC14025B, MC14071B, MC14073B,
MC14081B, MC14082B
The B Series logic gates are constructed with P and N channel
enhancement mode devices in a single monolithic structure
(Complementary MOS). Their primary use is where low power
dissipation and/or high noise immunity is desired.
http://onsemi.com
Features
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
• All Outputs Buffered
• Capable of Driving Two Low−power TTL Loads or One Low−power
•
•
•
•
Schottky TTL Load Over the Rated Temperature Range.
Double Diode Protection on All Inputs Except: Triple Diode
Protection on MC14011B and MC14081B
Pin−for−Pin Replacements for Corresponding CD4000 Series
B Suffix Devices
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
TSSOP−14
DT SUFFIX
CASE 948G
MARKING DIAGRAMS
14
14
14
0xxB
ALYWG
G
140xxBG
AWLYWW
1
1
SOIC−14
MAXIMUM RATINGS (Voltages Referenced to VSS)
Parameter
SOIC−14
D SUFFIX
CASE 751A
xx
A
WL, L
YY, Y
WW, W
G or G
TSSOP−14
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
Value
Unit
−0.5 to +18.0
V
−0.5 to VDD + 0.5
V
Input or Output Current
(DC or Transient) per Pin
± 10
mA
PD
Power Dissipation, per Package
(Note 1)
500
mW
TA
Ambient Temperature Range
−55 to +125
°C
MC14001B
Quad 2−Input NOR Gate
Tstg
Storage Temperature Range
−65 to +150
°C
MC14011B
Quad 2−Input NAND Gate
TL
Lead Temperature
(8−Second Soldering)
260
°C
MC14023B
Triple 3−Input NAND Gate
MC14025B
Triple 3−Input NOR Gate
MC14071B
Quad 2−Input OR Gate
MC14073B
Triple 3−Input AND Gate
MC14081B
Quad 2−Input AND Gate
MC14082B
Dual 4−Input AND Gate
Symbol
VDD
Vin, Vout
Iin, Iout
VESD
DC Supply Voltage Range
Input or Output Voltage Range
(DC or Transient)
ESD Withstand Voltage
Human Body Model
Machine Model
Charged Device Model
V
> 3000
> 300
N/A
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS ≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an appropriate logic voltage level
(e.g., either VSS or VDD). Unused outputs must be left open.
July, 2014 − Rev. 11
DEVICE INFORMATION
Device
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. Temperature Derating: “D/DW” Packages: –7.0 mW/_C From 65_C To 125_C
© Semiconductor Components Industries, LLC, 2014
(Note: Microdot may be in either location)
1
Description
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 8 of this data sheet.
Publication Order Number:
MC14001B/D
MC14001B Series
LOGIC DIAGRAMS
NAND
OR
AND
MC14001B
Quad 2−Input NOR Gate
MC14011B
Quad 2−Input NAND Gate
MC14071B
Quad 2−Input OR Gate
MC14081B
Quad 2−Input AND Gate
2 INPUT
NOR
1
2
3
1
2
3
1
2
3
1
2
3
5
6
4
5
6
4
5
6
4
5
6
4
8
9
10
8
9
10
8
9
10
8
9
10
12
13
11
12
13
11
12
13
11
12
13
11
3 INPUT
MC14025B
Triple 3−Input NOR Gate
1
2
8
3
4
5
11
12
13
9
6
10
MC14073B
Triple 3−Input AND Gate
MC14023B
Triple 3−Input NAND Gate
1
2
8
3
4
5
11
12
13
1
2
8
3
4
5
11
12
13
9
6
10
9
6
10
MC14082B
Dual 4−Input AND Gate
2
3
4
5
9
10
11
12
1
13
NC = 6, 8
VDD = PIN 14
VSS = PIN 7
FOR ALL DEVICES
PIN ASSIGNMENTS
MC14001B
Quad 2−Input NOR Gate
MC14023B
Triple 3−Input NAND Gate
MC14011B
Quad 2−Input NAND Gate
MC14025B
Triple 3−Input NOR Gate
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 3C
IN 2A
2
13
IN 3C
OUTA
3
12
IN 1D
OUTA
3
12
IN 1D
IN 1B
3
12
IN 2C
IN 1B
3
12
IN 2C
OUTB
4
11
OUTD
OUTB
4
11
OUTD
IN 2B
4
11
IN 1C
IN 2B
4
11
IN 1C
IN 1B
5
10
OUTC
IN 1B
5
10
OUTC
IN 3B
5
10
OUTC
IN 3B
5
10
OUTC
IN 2B
6
9
IN 2C
IN 2B
6
9
IN 2C
OUTB
6
9
OUTA
OUTB
6
9
OUTA
VSS
7
8
IN 1C
VSS
7
8
IN 1C
VSS
7
8
IN 3A
VSS
7
8
IN 3A
MC14071B
Quad 2−Input OR Gate
MC14073B
Triple 3−Input AND Gate
MC14081B
Quad 2−Input AND Gate
MC14082B
Dual 4−Input AND Gate
IN 1A
1
14
VDD
IN 1A
1
14
VDD
IN 1A
1
14
VDD
OUTA
1
14
VDD
IN 2A
2
13
IN 2D
IN 2A
2
13
IN 3C
IN 2A
2
13
IN 2D
IN 1A
2
13
OUTB
OUTA
3
12
IN 1D
IN 1B
3
12
IN 2C
OUTA
3
12
IN 1D
IN 2A
3
12
IN 4B
OUTB
4
11
OUTD
IN 2B
4
11
IN 1C
OUTB
4
11
OUTD
IN 3A
4
11
IN 3B
IN 1B
5
10
OUTC
IN 3B
5
10
OUTC
IN 1B
5
10
OUTC
IN 4A
5
10
IN 2B
IN 2B
6
9
IN 2C
OUTB
6
9
OUTA
IN 2B
6
9
IN 2C
NC
6
9
IN 1B
VSS
7
8
IN 1C
VSS
7
8
IN 3A
VSS
7
8
IN 1C
VSS
7
8
NC
NC = NO CONNECTION
http://onsemi.com
2
MC14001B Series
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
− 55_C
Characteristic
Output Voltage
Vin = VDD or 0
Symbol
25_C
VDD
Vdc
Min
Max
Min
Typ
(Note 2)
125_C
Max
Min
Max
Unit
“0” Level
VOL
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
“1” Level
VOH
5.0
10
15
4.95
9.95
14.95
−
−
−
4.95
9.95
14.95
5.0
10
15
−
−
−
4.95
9.95
14.95
−
−
−
Vdc
Input Voltage
“0” Level
(VO = 4.5 or 0.5 Vdc)
(VO = 9.0 or 1.0 Vdc)
(VO = 13.5 or 1.5 Vdc)
VIL
5.0
10
15
−
−
−
1.5
3.0
4.0
−
−
−
2.25
4.50
6.75
1.5
3.0
4.0
−
−
−
1.5
3.0
4.0
“1” Level
VIH
5.0
10
15
3.5
7.0
11
−
−
−
3.5
7.0
11
2.75
5.50
8.25
−
−
−
3.5
7.0
11
−
−
−
5.0
5.0
10
15
–3.0
–0.64
–1.6
–4.2
−
−
−
−
–2.4
–0.51
–1.3
–3.4
–4.2
–0.88
–2.25
–8.8
−
−
−
−
–1.7
–0.36
–0.9
–2.4
−
−
−
−
IOL
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
mAdc
Input Current
Iin
15
−
±0.1
−
±0.00001
±0.1
−
±1.0
mAdc
Input Capacitance
(Vin = 0)
Cin
−
−
−
−
5.0
7.5
−
−
pF
Quiescent Current
(Per Package)
IDD
5.0
10
15
−
−
−
0.25
0.5
1.0
−
−
−
0.0005
0.0010
0.0015
0.25
0.5
1.0
−
−
−
7.5
15
30
mAdc
IT
5.0
10
15
Vin = 0 or VDD
(VO = 0.5 or 4.5 Vdc)
(VO = 1.0 or 9.0 Vdc)
(VO = 1.5 or 13.5 Vdc)
Output Drive Current
(VOH = 2.5 Vdc)
(VOH = 4.6 Vdc)
(VOH = 9.5 Vdc)
(VOH = 13.5 Vdc)
(VOL = 0.4 Vdc)
(VOL = 0.5 Vdc)
(VOL = 1.5 Vdc)
Vdc
Vdc
IOH
Source
Sink
Total Supply Current (Notes 3, 4)
(Dynamic plus Quiescent,
Per Gate, CL = 50 pF)
mAdc
IT = (0.3 mA/kHz) f + IDD/N
IT = (0.6 mA/kHz) f + IDD/N
IT = (0.9 mA/kHz) f + IDD/N
mAdc
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
3. The formulas given are for the typical characteristics only at 25_C.
4. To calculate total supply current at loads other than 50 pF:
IT(CL) = IT(50 pF) + (CL − 50) Vfk
where: IT is in mA (per package), CL in pF, V = (VDD − VSS) in volts, f in kHz is input frequency, and k = 0.001 x the number of exercised gates
per package.
http://onsemi.com
3
MC14001B Series
B−SERIES GATE SWITCHING TIMES
SWITCHING CHARACTERISTICS (Note 5) (CL = 50 pF, TA = 25_C)
Characteristic
Symbol
Output Rise Time, All B−Series Gates
tTLH = (1.35 ns/pF) CL + 33 ns
tTLH = (0.60 ns/pF) CL + 20 ns
tTLH = (0.40 ns/PF) CL + 20 ns
tTLH
Output Fall Time, All B−Series Gates
tTHL = (1.35 ns/pF) CL + 33 ns
tTHL = (0.60 ns/pF) CL + 20 ns
tTHL = (0.40 ns/pF) CL + 20 ns
tTHL
Propagation Delay Time
MC14001B, MC14011B only
tPLH, tPHL = (0.90 ns/pF) CL + 80 ns
tPLH, tPHL = (0.36 ns/pF) CL + 32 ns
tPLH, tPHL = (0.26 ns/pF) CL + 27 ns
All Other 2, 3, and 4 Input Gates
tPLH, tPHL = (0.90 ns/pF) CL + 115 ns
tPLH, tPHL = (0.36 ns/pF) CL + 47 ns
tPLH, tPHL = (0.26 ns/pF) CL + 37 ns
8−Input Gates (MC14068B, MC14078B)
tPLH, tPHL = (0.90 ns/pF) CL + 155 ns
tPLH, tPHL = (0.36 ns/pF) CL + 62 ns
tPLH, tPHL = (0.26 ns/pF) CL + 47 ns
VDD
Vdc
Min
Typ
(Note 6)
Max
5.0
10
15
−
−
−
100
50
40
200
100
80
5.0
10
15
−
−
−
100
50
40
200
100
80
Unit
ns
ns
tPLH, tPHL
ns
5.0
10
15
−
−
−
125
50
40
250
100
80
5.0
10
15
−
−
−
160
65
50
300
130
100
5.0
10
15
−
−
−
200
80
60
350
150
110
5. The formulas given are for the typical characteristics only at 25_C.
6. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
14
PULSE
GENERATOR
20 ns
VDD
20 ns
INPUT
INPUT
OUTPUT
7
0V
tPLH
tPHL
CL
*
VDD
90%
50%
10%
OUTPUT
INVERTING
VSS
tTHL
tPLH
OUTPUT
NON-INVERTING
*All unused inputs of AND, NAND gates must be connected to VDD.
All unused inputs of OR, NOR gates must be connected to VSS.
tTLH
Figure 1. Switching Time Test Circuit and Waveforms
http://onsemi.com
4
VOH
90%
50%
10%
tTLH
tPHL
90%
50%
10%
tTHL
VOL
VOH
VOL
MC14001B Series
CIRCUIT SCHEMATIC
NOR, OR GATES
MC14001B, MC14071B
One of Four Gates Shown
MC14025B
One of Three Gates Shown
VDD
VDD
14
VDD
1, 3, 11
1, 6, 8, 13
*
2, 4, 12
2, 5, 9, 12
14
VDD
3, 4, 10, 11
*
VSS
VSS
7
9, 6, 10
VSS
VDD
*Inverter omitted in MC14001B
8, 5, 13
7
VSS
VSS
*Inverter omitted in MC14025B
CIRCUIT SCHEMATIC
NAND, AND GATES
MC14023B, MC14073B
One of Three Gates Shown
MC14011B, MC14081B
One of Four Gates Shown
VDD
14
VDD
*
3, 4, 10, 11
2, 4, 12
1, 3, 11
14
2, 5, 9, 12
VDD
1, 6, 8, 13
VSS
7 VSS
*Inverter omitted in MC14011B
*
VDD
9, 6, 10
8, 5, 13
7
VSS
VSS
*Inverter omitted in MC14023B
http://onsemi.com
5
MC14001B Series
TYPICAL B−SERIES GATE CHARACTERISTICS
N−CHANNEL DRAIN CURRENT (SINK)
P−CHANNEL DRAIN CURRENT (SOURCE)
- 10
5.0
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
- 9.0
4.0
TA = - 55°C
3.0
- 40°C
+ 85°C + 25°C
2.0
+ 125°C
1.0
- 8.0
TA = - 55°C
- 7.0
- 40°C
- 6.0
- 5.0
+ 25°C
+ 85°C
- 4.0
- 3.0
+ 125°C
- 2.0
- 1.0
0
0
1.0
2.0
3.0
4.0
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
0
5.0
0
Figure 2. VGS = 5.0 Vdc
- 50
- 45
TA = - 55°C
16
14
- 40°C
12
+ 25°C
+ 85°C
10
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
18
+ 125°C
8.0
6.0
- 40
- 35
- 25
+ 85°C
- 15
2.0
- 5.0
1.0
2.0 3.0 4.0 5.0 6.0 7.0 8.0
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
9.0
0
10
- 40°C
+ 25°C
- 20
- 10
0
TA = - 55°C
- 30
4.0
+ 125°C
0
Figure 4. VGS = 10 Vdc
- 100
45
- 90
40
- 80
35
TA = - 55°C
30
- 40°C
25
+ 25°C
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
- 1.0 - 2.0 - 3.0 - 4.0 - 5.0 - 6.0 - 7.0 - 8.0 - 9.0 - 10
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
Figure 5. VGS = − 10 Vdc
50
+ 85°C
20
+ 125°C
15
10
5.0
0
- 5.0
Figure 3. VGS = − 5.0 Vdc
20
0
- 1.0
- 2.0
- 3.0
- 4.0
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
- 70
- 60
TA = - 55°C
- 50
- 40°C
+ 25°C
- 40
+ 85°C
- 30
+ 125°C
- 20
- 10
0
2.0
4.0 6.0 8.0 10
12
14
16
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
18
0
20
0
Figure 6. VGS = 15 Vdc
- 2.0 - 4.0 - 6.0 - 8.0 - 10 - 12 - 14 - 16
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
Figure 7. VGS = − 15 Vdc
These typical curves are not guarantees, but are design aids.
Caution: The maximum rating for output current is 10 mA per pin.
http://onsemi.com
6
- 18 - 20
MC14001B Series
TYPICAL B−SERIES GATE CHARACTERISTICS (cont’d)
V out , OUTPUT VOLTAGE (Vdc)
V out , OUTPUT VOLTAGE (Vdc)
VOLTAGE TRANSFER CHARACTERISTICS
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
5.0
4.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
3.0
2.0
1.0
0
0
1.0
2.0
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
10
8.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
6.0
4.0
2.0
0
3.0
4.0
5.0
Vin, INPUT VOLTAGE (Vdc)
0
2.0
Figure 8. VDD = 5.0 Vdc
V out , OUTPUT VOLTAGE (Vdc)
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 9. VDD = 10 Vdc
DC NOISE MARGIN
16
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
14
The DC noise margin is defined as the input voltage range
from an ideal “1” or “0” input level which does not produce
output state change(s). The typical and guaranteed limit
values of the input values VIL and VIH for the output(s) to
be at a fixed voltage VO are given in the Electrical
Characteristics table. VIL and VIH are presented graphically
in Figure 11.
Guaranteed minimum noise margins for both the “1” and
“0” levels =
12
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
10
8.0
6.0
4.0
2.0
0
4.0
0
2.0
4.0
1.0 V with a 5.0 V supply
2.0 V with a 10.0 V supply
2.5 V with a 15.0 V supply
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 10. VDD = 15 Vdc
Vout
VDD
Vout
VO
VO
VO
VO
VDD
VDD
0
VDD
Vin
VIL
0
VIH
Vin
VIL
VIH
VSS = 0 VOLTS DC
(a) Inverting Function
(b) Non−Inverting Function
Figure 11. DC Noise Immunity
http://onsemi.com
7
MC14001B Series
ORDERING INFORMATION
Device
MC14001BDG
NLV14001BDG*
MC14001BDR2G
NLV14001BDR2G*
MC14001BDTR2G
NLV14001BDTR2G*
MC14001BFELG
MC14011BDG
NLV14011BDG*
MC14011BDR2G
NLV14011BDR2G*
MC14011BDTR2G
NLV14011BDTR2G*
MC14011BFG
MC14011BFELG
Package
Shipping†
SOIC−14
(Pb−Free)
55 Units / Rail
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
TSSOP−14
(Pb−Free)
SOEIAJ−14
(Pb−Free)
2000 Units / Tape & Reel
SOIC−14
(Pb−Free)
55 Units / Rail
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
TSSOP−14
(Pb−Free)
SOEIAJ−14
(Pb−Free)
50 Units / Rail
2000 Units / Tape & Reel
MC14023BDG
SOIC−14
(Pb−Free)
55 Units / Rail
MC14023BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
SOEIAJ−14
(Pb−Free)
2000 Units / Tape & Reel
SOIC−14
(Pb−Free)
55 Units / Rail
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
SOIC−14
(Pb−Free)
55 Units / Rail
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
NLV14023BDR2G*
MC14023BFELG
MC14025BDG
NLV14025BDG*
MC14025BDR2G
NLV14025BDR2G*
MC14071BDG
NLV14071BDG*
MC14071BDR2G
NLV14071BDR2G*
MC14071BDTG
MC14071BDTR2G
96 Units per Rail
TSSOP−14
(Pb−Free)
NLV14071BDTR2G*
2500 Units / Tape & Reel
MC14073BDG
SOIC−14
(Pb−Free)
55 Units / Rail
MC14073BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
http://onsemi.com
8
MC14001B Series
ORDERING INFORMATION (continued)
Device
MC14081BDG
NLV14081BDG*
MC14081BDR2G
NLV14081BDR2G*
MC14081BDTR2G
NLV14081BDTR2G*
Package
Shipping†
SOIC−14
(Pb−Free)
55 Units / Rail
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
TSSOP−14
(Pb−Free)
MC14082BDG
NLV14082BDG*
SOIC−14
(Pb−Free)
MC14082BDR2G
55 Units / Rail
2500 Units / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
9
MC14001B Series
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
K
A
−V−
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
J J1
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
10
MILLIMETERS
INCHES
MIN
MAX
MIN MAX
4.90
5.10 0.193 0.200
4.30
4.50 0.169 0.177
−−−
1.20
−−− 0.047
0.05
0.15 0.002 0.006
0.50
0.75 0.020 0.030
0.65 BSC
0.026 BSC
0.50
0.60 0.020 0.024
0.09
0.20 0.004 0.008
0.09
0.16 0.004 0.006
0.19
0.30 0.007 0.012
0.19
0.25 0.007 0.010
6.40 BSC
0.252 BSC
0_
8_
0_
8_
MC14001B Series
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE K
D
A
B
14
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
8
A3
E
H
L
1
0.25
M
DETAIL A
7
B
13X
M
b
0.25
M
C A
S
B
S
e
DETAIL A
h
A
X 45 _
M
A1
C
SEATING
PLANE
DIM
A
A1
A3
b
D
E
e
H
h
L
M
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.19
0.25
0.35
0.49
8.55
8.75
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
INCHES
MIN
MAX
0.054 0.068
0.004 0.010
0.008 0.010
0.014 0.019
0.337 0.344
0.150 0.157
0.050 BSC
0.228 0.244
0.010 0.019
0.016 0.049
0_
7_
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC14001B/D