MC14012B D

MC14012B
Dual 4-Input NAND Gates
The MC14012B dual 4−input NAND gates are constructed with
P−Channel and N−Channel enhancement mode devices in a single
monolithic structure (Complementary MOS). Their primary use is
where low power dissipation and/or high noise immunity is desired.
http://onsemi.com
Features
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
• All Outputs Buffered
• Capable of Driving Two Low−Power TTL Loads or One Low−Power
•
•
•
•
Schottky TTL Load Over the Rated Temperature Range
Double Diode Protection on All Inputs
Pin−for−Pin Replacements for Corresponding CD4000 Series B
Suffix Devices
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
This Device is Pb−Free and is RoHS Compliant
SOIC−14
D SUFFIX
CASE 751A
MARKING DIAGRAM
14
14012BG
AWLYWW
1
MAXIMUM RATINGS (Voltages Referenced to VSS)
Parameter
Value
Unit
−0.5 to +18.0
V
−0.5 to VDD + 0.5
V
Input or Output Current
(DC or Transient) per Pin
± 10
mA
PD
Power Dissipation, per Package
(Note 1)
500
mW
TA
Ambient Temperature Range
−55 to +125
°C
Tstg
Storage Temperature Range
−65 to +150
°C
TL
Lead Temperature
(8−Second Soldering)
260
°C
Symbol
VDD
Vin, Vout
Iin, Iout
DC Supply Voltage Range
Input or Output Voltage Range
(DC or Transient)
A
WL, L
YY, Y
WW, W
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. Temperature Derating: “D/DW” Package: –7.0 mW/_C From 65_C To 125_C
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS ≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an appropriate logic voltage level
(e.g., either VSS or VDD). Unused outputs must be left open.
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 11
1
Publication Order Number:
MC14012B/D
MC14012B
MC14012B
Dual 4−Input NAND Gate
OUTA
1
14
VDD
IN 1A
2
13
OUTB
IN 2A
3
12
IN 4B
IN 3A
4
11
IN 3B
IN 4A
5
10
IN 2B
NC
6
9
IN 1B
VSS
7
8
NC
2
3
4
5
9
10
11
12
1
13
NC = 6, 8
VDD = PIN 14
VSS = PIN 7
NC = NO CONNECTION
Figure 1. Pin Assignment
Figure 2. Logic Diagram
ORDERING INFORMATION
Package
Shipping†
MC14012BDG
SOIC−14
(Pb−Free)
55 Units / Rail
NLV14012BDG*
SOIC−14
(Pb−Free)
55 Units / Rail
MC14012BDR2G
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
NLV14012BDR2G*
SOIC−14
(Pb−Free)
2500 Units / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
2
MC14012B
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
−55_C
Characteristic
Output Voltage
Vin = VDD or 0
Symbol
25_C
VDD
Vdc
Min
Max
Min
Typ
(Note 2)
125_C
Max
Min
Max
Unit
“0” Level
VOL
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
“1” Level
VOH
5.0
10
15
4.95
9.95
14.95
−
−
−
4.95
9.95
14.95
5.0
10
15
−
−
−
4.95
9.95
14.95
−
−
−
Vdc
“0” Level
VIL
5.0
10
15
−
−
−
1.5
3.0
4.0
−
−
−
2.25
4.50
6.75
1.5
3.0
4.0
−
−
−
1.5
3.0
4.0
5.0
10
15
3.5
7.0
11
−
−
−
3.5
7.0
11
2.75
5.50
8.25
−
−
−
3.5
7.0
11
−
−
−
5.0
5.0
10
15
–3.0
–0.64
–1.6
–4.2
−
−
−
−
–2.4
–0.51
–1.3
–3.4
–4.2
–0.88
–2.25
–8.8
−
−
−
−
–1.7
–0.36
–0.9
–2.4
−
−
−
−
IOL
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
mAdc
Input Current
Iin
15
−
±0.1
−
±0.00001
±0.1
−
±1.0
mAdc
Input Capacitance
(Vin = 0)
Cin
−
−
−
−
5.0
7.5
−
−
pF
Quiescent Current
(Per Package)
IDD
5.0
10
15
−
−
−
0.25
0.5
1.0
−
−
−
0.0005
0.0010
0.0015
0.25
0.5
1.0
−
−
−
7.5
15
30
mAdc
IT
5.0
10
15
Vin = 0 or VDD
Input Voltage
(VO = 4.5 or 0.5 Vdc)
(VO = 9.0 or 1.0 Vdc)
(VO = 13.5 or 1.5 Vdc)
“1” Level
VIH
(VO = 0.5 or 4.5 Vdc)
(VO = 1.0 or 9.0 Vdc)
(VO = 1.5 or 13.5 Vdc)
Output Drive Current
(VOH = 2.5 Vdc)
(VOH = 4.6 Vdc)
(VOH = 9.5 Vdc)
(VOH = 13.5 Vdc)
(VOL = 0.4 Vdc)
(VOL = 0.5 Vdc)
(VOL = 1.5 Vdc)
Vdc
Vdc
IOH
Source
Sink
Total Supply Current (Notes 3, 4)
(Dynamic plus Quiescent,
Per Gate, CL = 50 pF)
mAdc
IT = (0.3 mA/kHz) f + IDD/N
IT = (0.6 mA/kHz) f + IDD/N
IT = (0.9 mA/kHz) f + IDD/N
mAdc
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
3. The formulas given are for the typical characteristics only at 25_C.
4. To calculate total supply current at loads other than 50 pF:
IT(CL) = IT(50 pF) + (CL − 50) Vfk
where: IT is in mA (per package), CL in pF, V = (VDD − VSS) in volts, f in kHz is input frequency, and k = 0.001 x the number of exercised
gates per package.
http://onsemi.com
3
MC14012B
SWITCHING CHARACTERISTICS (Note 5) (CL = 50 pF, TA = 25_C)
Characteristic
Symbol
Output Rise Time
tTLH = (1.35 ns/pF) CL + 33 ns
tTLH = (0.60 ns/pF) CL + 20 ns
tTLH = (0.40 ns/PF) CL + 20 ns
tTLH
Output Fall Time
tTHL = (1.35 ns/pF) CL + 33 ns
tTHL = (0.60 ns/pF) CL + 20 ns
tTHL = (0.40 ns/pF) CL + 20 ns
tTHL
Propagation Delay Time
tPLH, tPHL = (0.90 ns/pF) CL + 115 ns
tPLH, tPHL = (0.36 ns/pF) CL + 47 ns
tPLH, tPHL = (0.26 ns/pF) CL + 37 ns
VDD
Vdc
Min
Typ
(Note 6)
Max
5.0
10
15
−
−
−
100
50
40
200
100
80
5.0
10
15
−
−
−
100
50
40
200
100
80
5.0
10
15
−
−
−
160
65
50
300
130
100
Unit
ns
ns
tPLH, tPHL
ns
5. The formulas given are for the typical characteristics only at 25_C.
6. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
14
20 ns
VDD
20 ns
PULSE
GENERATOR
INPUT
OUTPUT
tPHL
CL
*
7
OUTPUT
INVERTING
*All unused inputs of AND, NAND gates must be connected to VDD.
All unused inputs of OR, NOR gates must be connected to VSS.
90%
50%
10%
tTHL
tPLH
Figure 3. Switching Time Test Circuit and Waveforms
VDD
VDD
2, 9
*
3, 10
VSS
4, 11
5, 12
1, 13
SAME AS
ABOVE
7
*Inverter omitted
VSS
Figure 4. Circuit Schematic − One of Two Gates Shown
http://onsemi.com
4
VOH
tTLH
tPHL
tTLH
14
0V
tPLH
OUTPUT
NON−INVERTING
VSS
VDD
90%
50%
10%
INPUT
90%
50%
10%
tTHL
VOL
VOH
VOL
MC14012B
TYPICAL B−SERIES GATE CHARACTERISTICS
N−CHANNEL DRAIN CURRENT (SINK)
P−CHANNEL DRAIN CURRENT (SOURCE)
−10
5.0
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
−9.0
4.0
TA = −55°C
3.0
−40°C
+85°C +25°C
2.0
+125°C
1.0
−8.0
TA = −55°C
−7.0
−40°C
−6.0
−5.0
+25°C
+85°C
−4.0
−3.0
+125°C
−2.0
−1.0
0
0
0
1.0
2.0
3.0
4.0
0
5.0
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
Figure 5. VGS = 5.0 Vdc
−4.0
−5.0
−45
TA = −55°C
16
14
−40°C
12
+25°C
+85°C
10
ID , DRAIN CURRENT (mA)
ID , DRAIN CURRENT (mA)
−3.0
−50
18
+125°C
8.0
6.0
−40
−35
TA = −55°C
−30
−25
+ 25°C
−20
+85°C
+125°C
−10
2.0
−5.0
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
0
0
10
−1.0 −2.0 −3.0 −4.0 −5.0 −6.0 −7.0 −8.0 −9.0 −10
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
Figure 7. VGS = 10 Vdc
Figure 8. VGS = − 10 Vdc
- 100
45
- 90
40
- 80
ID , DRAIN CURRENT (mA)
50
TA = −55°C
35
30
−40°C
25
+25°C
20
+85°C
+125°C
15
−40°C
−15
4.0
0
ID , DRAIN CURRENT (mA)
−2.0
Figure 6. VGS = − 5.0 Vdc
20
10
5.0
0
−1.0
VDS, DRAIN−TO−SOURCE VOLTAGE (Vdc)
- 70
- 60
TA = −55°C
- 50
−40°C
+25°C
- 40
+85°C
- 30
+125°C
- 20
- 10
0
2.0
4.0
6.0
8.0
10
12
14
16
18
0
20
0
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
Figure 9. VGS = 15 Vdc
−2.0 −4.0 −6.0 −8.0 −10 −12 −14 −16 −18 −20
VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc)
Figure 10. VGS = − 15 Vdc
These typical curves are not guarantees, but are design aids.
Caution: The maximum rating for output current is 10 mA per pin.
http://onsemi.com
5
MC14012B
V out , OUTPUT VOLTAGE (Vdc)
V out , OUTPUT VOLTAGE (Vdc)
VOLTAGE TRANSFER CHARACTERISTICS
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
5.0
4.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
3.0
2.0
1.0
0
0
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
10
8.0
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, AND
6.0
4.0
2.0
0
1.0
0
2.0
3.0
4.0
5.0
Vin, INPUT VOLTAGE (Vdc)
2.0
4.0
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 11. VDD = 5.0 Vdc
DC NOISE MARGIN
SINGLE INPUT NAND, AND
MULTIPLE INPUT NOR, OR
16
V out , OUTPUT VOLTAGE (Vdc)
Figure 12. VDD = 10 Vdc
The DC noise margin is defined as the input voltage range
from an ideal “1” or “0” input level which does not produce
output state change(s). The typical and guaranteed limit
values of the input values VIL and VIH for the output(s) to
be at a fixed voltage VO are given in the Electrical
Characteristics table. VIL and VIH are presented graphically
in Figure 11.
Guaranteed minimum noise margins for both the “1” and
“0” levels =
1.0 V with a 5.0 V supply
2.0 V with a 10.0 V supply
2.5 V with a 15.0 V supply
14
12
SINGLE INPUT NOR, OR
MULTIPLE INPUT NAND, A
10
8.0
6.0
4.0
2.0
0
0
2.0
4.0
6.0
8.0
10
Vin, INPUT VOLTAGE (Vdc)
Figure 13. VDD = 15 Vdc
VDD
Vout
Vout
VO
VO
VO
VO
VDD
VDD
VDD
0
Vin
0
VIL
Vin
VIL
VIH
VIH
VSS = 0 VOLTS DC
(a) Inverting Function
(b) Non−Inverting Function
Figure 14. DC Noise Immunity
http://onsemi.com
6
MC14012B
PACKAGE DIMENSIONS
D
SOIC−14 NB
CASE 751A−03
ISSUE K
A
B
14
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
8
A3
E
H
L
1
0.25
M
DETAIL A
7
B
13X
M
b
0.25
M
C A
S
B
S
e
DETAIL A
h
A
X 45 _
M
A1
C
SEATING
PLANE
DIM
A
A1
A3
b
D
E
e
H
h
L
M
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.19
0.25
0.35
0.49
8.55
8.75
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
INCHES
MIN
MAX
0.054 0.068
0.004 0.010
0.008 0.010
0.014 0.019
0.337 0.344
0.150 0.157
0.050 BSC
0.228 0.244
0.010 0.019
0.016 0.049
0_
7_
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC14012B/D