ESD8351 D

ESD8351, SZESD8351
ESD Protection Diodes
Low Capacitance ESD Protection Diode
for High Speed Data Line
The ESD8351 Series ESD protection diodes are designed to protect
high speed data lines from ESD. Ultra−low capacitance and low ESD
clamping voltage make this device an ideal solution for protecting
voltage sensitive high speed data lines.
www.onsemi.com
MARKING
DIAGRAMS
Features
PIN 1
• USB 2.0
• eSATA
1
2
SOD−523
CASE 502
1
AE
M
AF
1
2
= Specific Device Code
= Date Code
PIN CONFIGURATION
AND SCHEMATIC
MAXIMUM RATINGS (TJ = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
Operating Junction Temperature Range
TJ
−55 to +125
°C
Storage Temperature Range
Tstg
−55 to +150
°C
Lead Solder Temperature −
Maximum (10 Seconds)
TL
260
°C
ESD
ESD
ESD
±15
±15
±30
kV
kV
kV
Ipp
5.0
A
Maximum Peak Pulse Current
8/20 ms @ TA = 25°C
SOD−323
CASE 477
X, XX
M
Typical Applications
IEC 61000−4−2 Contact (ESD)
IEC 61000−4−2 Air (ESD)
ISO 10605 330 pF / 2 kW Contact
2
M
1
Cathode
2
Anode
=
•
IEC 61000−4−2 (Level 4)
ISO 10605
Low ESD Clamping Voltage
SZ Prefix for Automotive and Other Applications Requiring Unique
Site and Control Change Requirements; AEC−Q101 Qualified and
PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
L
•
•
X3DFN2
CASE 152AF
M
• Low Capacitance (0.55 pF Max, I/O to GND)
• Protection for the Following IEC Standards:
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
See Application Note AND8308/D for further description of
survivability specs.
© Semiconductor Components Industries, LLC, 2016
May, 2016 − Rev. 8
1
Publication Order Number:
ESD8351/D
ESD8351, SZESD8351
ELECTRICAL CHARACTERISTICS
I
(TA = 25°C unless otherwise noted)
Symbol
VRWM
IR
VBR
IPP
Parameter
Working Peak Voltage
RDYN
Maximum Reverse Leakage Current @ VRWM
VBR
Breakdown Voltage @ IT
V
VC VRWMVHOLD
Test Current
IR
IT
VHOLD
Holding Reverse Voltage
IHOLD
IHOLD
Holding Reverse Current
RDYN
Dynamic Resistance
IT
VC
RDYN
IPP
Maximum Peak Pulse Current
VC
Clamping Voltage @ IPP
VC = VHOLD + (IPP * RDYN)
−IPP
VC = VHOLD + (IPP * RDYN)
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified)
Parameter
Reverse Working Voltage
Breakdown Voltage
Symbol
VRWM
VBR
Conditions
Min
Typ
I/O Pin to GND
IT = 1 mA, I/O Pin to GND
5.5
7.0
Unit
3.3
V
7.8
V
500
nA
Reverse Leakage Current
IR
Holding Reverse Voltage
VHOLD
I/O Pin to GND
1.15
V
Holding Reverse Current
IHOLD
I/O Pin to GND
20
mA
Clamping Voltage
TLP (Note 2)
See Figures 1 through 11
VC
V
Clamping Voltage (Note 3)
VC
Dynamic Resistance
RDYN
Junction Capacitance
CJ
VRWM = 3.3 V, I/O Pin to GND
Max
IPP = 8 A
IEC 61000−4−2 Level 2 equivalent
(±4 kV Contact, ±4 kV Air)
6.5
IPP = 16 A
IEC 61000−4−2 Level 4 equivalent
(±8 kV Contact, ±15 kV Air)
11.2
IPP = 5 A
tp = 8 x 20 ms
8.2
V
Pin1 to Pin2
Pin2 to Pin1
0.62
0.59
W
VR = 0 V, f = 1 Mhz
VR = 0 V, f = 2.5 Ghz
0.37
0.35
0.55
0.45
pF
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. For test procedure see Figures 8 and 9 and application note AND8307/D.
2. ANSI/ESD STM5.5.1 − Electrostatic Discharge Sensitivity Testing using Transmission Line Pulse (TLP) Model.
TLP conditions: Z0 = 50 W, tp = 100 ns, tr = 4 ns, averaging window; t1 = 30 ns to t2 = 60 ns.
3. Non−repetitive current pulse at TA = 20°C, per IEC 61000−4−5 waveform.
www.onsemi.com
2
1.0
10
0.9
9
0.8
8
0.7
7
0.6
6
Vpk (V)
0.5
0.4
5
4
0.3
3
0.2
2
0.1
0
1
0
0.5
1.0
1.5
2.0
2.5
3.0
0
3.5
1
3
2.5
3.5
4
4.5
5
6
5.5
VBias (V)
Ipk (A)
Figure 2. Clamping Voltage vs Peak Pulse
Current ( tp = 8/20 ms)
1.0
m1
m2
0
0.9
0.8
CAPACITANCE (pF)
−2
−4
dB
2
Figure 1. CV Characteristics
2
−6
−8
−10
0.7
0.6
0.5
0.4
0.3
0.2
−12
0.1
−14
0
1E7
1E8
1
1E10 3E10
1E9
2
3
5
4
6
7
9
8
FREQUENCY (Hz)
FREQUENCY
Figure 3. RF Insertion Loss
Figure 4. Capacitance over Frequency
20
10
20
10
10
18
8
14
12
6
10
8
4
6
4
2
16
TLP CURRENT (A)
16
EQUIVALENT VIEC (kV)
18
TLP CURRENT (A)
1.5
8
14
12
6
10
8
4
6
4
2
2
2
0
0
0
0
2
4
6
8
10
12
14
16
18
0
0
20
VC, VOLTAGE (V)
2
4
6
8
10
12
14
16
18
VC, VOLTAGE (V)
Figure 5. Positive TLP I−V Curve
Figure 6. Negative TLP I−V Curve
www.onsemi.com
3
20
EQUIVALENT VIEC (kV)
C (pF)
ESD8351, SZESD8351
ESD8351, SZESD8351
Latch−Up Considerations
stable operating point of the circuit and the system is
therefore latch−up free. In the non−latch up free load line
case, the IV characteristic of the snapback protection device
intersects the load−line in two points (VOPA, IOPA) and
(VOPB, IOPB). Therefore in this case, the potential for
latch−up exists if the system settles at (VOPB, IOPB) after a
transient. Because of this, ESD8351 Series should not be
used for HDMI applications – ESD8104 or ESD8040 have
been designed to be acceptable for HDMI applications
without latch−up. Please refer to Application Note
AND9116/D for a more in−depth explanation of latch−up
considerations using ESD8000 series devices.
ON Semiconductor’s 8000 series of ESD protection
devices utilize a snap−back, SCR type structure. By using
this technology, the potential for a latch−up condition was
taken into account by performing load line analysis of
common high speed serial interfaces. Example load lines for
latch−up free applications and applications with the
potential for latch−up are shown below with a generic IV
characteristic of a snapback, SCR type structured device
overlaid on each. In the latch−up free load line case, the IV
characteristic of the snapback protection device intersects
the load−line in one unique point (VOP, IOP). This is the only
I
I
ISSMAX
ISSMAX
IOP
VOP
IOPB
IOPA
V
VDD
V
ESD8351 Latch*up free:
USB 2.0 LS/FS, USB 2.0 HS, USB 3.0 SS,
DisplayPort
VOPA
VOPB
VDD
ESD8351 Potential Latch*up:
HDMI 1.4/1.3a TMDS
Figure 7. Example Load Lines for Latch−up Free Applications and Applications with the Potential for Latch−up
Table 1. SUMMARY OF SCR REQUIREMENTS FOR LATCH−UP FREE APPLICATIONS
Application
VBR (min)
(V)
IH (min)
(mA)
VH (min)
(V)
ON Semiconductor ESD8000 Series
Recommended PN
HDMI 1.4/1.3a TMDS
3.465
54.78
1.0
ESD8104, ESD8040
USB 2.0 LS/FS
3.301
1.76
1.0
ESD8004, ESD8351
USB 2.0 HS
0.482
N/A
1.0
ESD8004, ESD8351
USB 3.0 SS
2.800
N/A
1.0
ESD8004, ESD8006, ESD8351
DisplayPort
3.600
25.00
1.0
ESD8004, ESD8006, ESD8351
www.onsemi.com
4
ESD8351, SZESD8351
IEC61000−4−2 Waveform
IEC 61000−4−2 Spec.
Ipeak
Level
Test Voltage (kV)
First Peak
Current
(A)
Current at
30 ns (A)
Current at
60 ns (A)
1
2
7.5
4
2
2
4
15
8
4
3
6
22.5
12
6
4
8
30
16
8
100%
90%
I @ 30 ns
I @ 60 ns
10%
tP = 0.7 ns to 1 ns
Figure 8. IEC61000−4−2 Spec
ESD Gun
Oscilloscope
TVS
50 W
Cable
50 W
Figure 9. Diagram of ESD Clamping Voltage Test Setup
The following is taken from Application Note
AND8308/D − Interpretation of Datasheet Parameters
for ESD Devices.
systems such as cell phones or laptop computers it is not
clearly defined in the spec how to specify a clamping voltage
at the device level. ON Semiconductor has developed a way
to examine the entire voltage waveform across the ESD
protection diode over the time domain of an ESD pulse in the
form of an oscilloscope screenshot, which can be found on
the datasheets for all ESD protection diodes. For more
information on how ON Semiconductor creates these
screenshots and how to interpret them please refer to
AND8307/D.
ESD Voltage Clamping
For sensitive circuit elements it is important to limit the
voltage that an IC will be exposed to during an ESD event
to as low a voltage as possible. The ESD clamping voltage
is the voltage drop across the ESD protection diode during
an ESD event per the IEC61000−4−2 waveform. Since the
IEC61000−4−2 was written as a pass/fail spec for larger
www.onsemi.com
5
ESD8351, SZESD8351
Transmission Line Pulse (TLP) Measurement
L
Transmission Line Pulse (TLP) provides current versus
voltage (I−V) curves in which each data point is obtained
from a 100 ns long rectangular pulse from a charged
transmission line. A simplified schematic of a typical TLP
system is shown in Figure 10. TLP I−V curves of ESD
protection devices accurately demonstrate the product’s
ESD capability because the 10s of amps current levels and
under 100 ns time scale match those of an ESD event. This
is illustrated in Figure 11 where an 8 kV IEC 61000−4−2
current waveform is compared with TLP current pulses at
8 A and 16 A. A TLP I−V curve shows the voltage at which
the device turns on as well as how well the device clamps
voltage over a range of current levels.
50 W Coax
Cable
S Attenuator
÷
50 W Coax
Cable
IM
10 MW
VM
DUT
VC
Oscilloscope
Figure 10. Simplified Schematic of a Typical TLP
System
Figure 11. Comparison Between 8 kV IEC 61000−4−2 and 8 A and 16 A TLP Waveforms
ORDERING INFORMATION
Package
Shipping†
ESD8351HT1G,
SZESD8351HT1G*
SOD−323
(Pb−Free)
3000 / Tape & Reel
ESD8351XV2T1G,
SZESD8351XV2T1G*
SOD−523
(Pb−Free)
3000 / Tape & Reel
ESD8351MUT5G
X3DFN2
(Pb−Free)
10000 / Tape & Reel
SZESD8351MUT5G*
X3DFN2
(Pb−Free)
15000 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*SZ Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q101 Qualified and PPAP
Capable.
www.onsemi.com
6
ESD8351, SZESD8351
PACKAGE DIMENSIONS
X3DFN2, 0.62x0.32, 0.355P, (0201)
CASE 152AF
ISSUE A
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
A B
D
PIN 1
INDICATOR
(OPTIONAL)
DIM
A
A1
b
D
E
e
L2
E
TOP VIEW
0.05 C
MILLIMETERS
MIN
MAX
0.25
0.33
−−−
0.05
0.22
0.28
0.58
0.66
0.28
0.36
0.355 BSC
0.17
0.23
A
RECOMMENDED
MOUNTING FOOTPRINT*
0.05 C
2X
A1
SIDE VIEW
C
SEATING
PLANE
0.74
e
2X
1
1
b
2
2X
2X
0.05
M
2X
0.30
0.05
L2
M
See Application Note AND8398/D for more mounting details
C A B
BOTTOM VIEW
0.31
DIMENSIONS: MILLIMETERS
C A B
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
7
ESD8351, SZESD8351
PACKAGE DIMENSIONS
SOD−323
CASE 477−02
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. LEAD THICKNESS SPECIFIED PER L/F DRAWING
WITH SOLDER PLATING.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
5. DIMENSION L IS MEASURED FROM END OF RADIUS.
HE
D
b
1
2
E
MILLIMETERS
DIM MIN
NOM MAX
A
0.80
0.90
1.00
A1 0.00
0.05
0.10
A3
0.15 REF
b
0.25
0.32
0.4
C 0.089
0.12 0.177
D
1.60
1.70
1.80
E
1.15
1.25
1.35
L
0.08
HE
2.30
2.50
2.70
A3
A
C
NOTE 3
L
NOTE 5
A1
SOLDERING FOOTPRINT*
0.63
0.025
0.83
0.033
1.60
0.063
2.85
0.112
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
8
INCHES
NOM MAX
0.035 0.040
0.002 0.004
0.006 REF
0.010 0.012 0.016
0.003 0.005 0.007
0.062 0.066 0.070
0.045 0.049 0.053
0.003
0.090 0.098 0.105
MIN
0.031
0.000
ESD8351, SZESD8351
PACKAGE DIMENSIONS
SOD−523
CASE 502
ISSUE E
−X−
D
NOTES:
6. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
7. CONTROLLING DIMENSION: MILLIMETERS.
8. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH.
MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF
BASE MATERIAL.
9. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS.
−Y−
E
2X
b
0.08
1
M
2
X Y
DIM
A
b
c
D
E
HE
L
L2
TOP VIEW
A
c
HE
RECOMMENDED
SOLDERING FOOTPRINT*
SIDE VIEW
2X
2X
L
2X
0.40
L2
BOTTOM VIEW
1.80
0.48
PACKAGE
OUTLINE
2X
MILLIMETERS
MIN
NOM
MAX
0.50
0.60
0.70
0.25
0.30
0.35
0.07
0.14
0.20
1.10
1.20
1.30
0.70
0.80
0.90
1.50
1.60
1.70
0.30 REF
0.15
0.20
0.25
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ESD8351/D