MC14521B
24-Stage Frequency Divider
The MC14521B consists of a chain of 24 flip−flops with an input
circuit that allows three modes of operation. The input will function as a
crystal oscillator, an RC oscillator, or as an input buffer for an external
oscillator. Each flip−flop divides the frequency of the previous flip−flop
by two, consequently this part will count up to 224 = 16,777,216.
The count advances on the negative going edge of the clock.
The outputs of the last seven−stages are available for added flexibility.
http://onsemi.com
Features
• All Stages are Resettable
• Reset Disables the RC Oscillator for Low Standby Power Drain
• RC and Crystal Oscillator Outputs Are Capable of Driving External
•
•
•
•
•
•
Loads
Test Mode to Reduce Test Time
VDD′ and VSS′ Pins Brought Out on Crystal Oscillator Inverter to
Allow the Connection of External Resistors for Low−Power Operation
Supply Voltage Range = 3.0 Vdc to 18 Vdc
Capable of Driving Two Low−Power TTL Loads or One Low−Power
Schottky TTL Load over the Rated Temperature Range
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
This Device is Pb−Free and is RoHS Compliant
1
SOIC−16
D SUFFIX
CASE 751B
PIN ASSIGNMENT
Q24
1
16
VDD
RESET
2
15
Q23
VSS4
3
14
Q22
OUT 2
4
13
Q21
VDD4
5
12
Q20
IN 2
6
11
Q19
OUT1
7
10
Q18
VSS
8
9
IN 1
MAXIMUM RATINGS (Voltages Referenced to VSS)
Symbol
Value
Unit
VDD
−0.5 to +18.0
V
Vin, Vout
−0.5 to VDD
+0.5
V
Input or Output Current (DC or Transient)
per Pin
Iin, Iout
±10
mA
1
Power Dissipation, per Package (Note 1)
PD
500
mW
Ambient Temperature Range
TA
−55 to +125
°C
Storage Temperature Range
Tstg
−65 to +150
°C
Lead Temperature (8−Second Soldering)
TL
260
°C
A
WL, L
YY, Y
WW, W
G
Parameter
DC Supply Voltage Range
Input or Output Voltage Range
(DC or Transient)
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
1. Temperature Derating: “D/DW” Package: –7.0 mW/_C From 65_C To 125_C
This device contains protection circuitry to guard against damage due to high
static voltages or electric fields. However, precautions must be taken to avoid
applications of any voltage higher than maximum rated voltages to this
high−impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS ≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an appropriate logic voltage level
(e.g., either VSS or VDD). Unused outputs must be left open.
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 10
1
MARKING DIAGRAMS
16
14521BG
AWLYWW
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 2 of this data sheet.
Publication Order Number:
MC14521B/D
MC14521B
BLOCK DIAGRAM
RESET
2
9
IN 1
STAGES
1 THRU 17
6
IN 2
7
OUT 1
5
VDD′
3
VSS′
4
OUT2
STAGES
18 THRU 24
Q18 Q19 Q20 Q21 Q22 Q23 Q24
VDD = PIN 16
VSS = PIN 8
10
11
12
13
14
15
1
Output
Count Capacity
Q18
Q19
Q20
Q21
Q22
Q23
Q24
218 = 262,144
219 = 524,288
220 = 1,048,576
221 = 2,097,152
222 = 4,194,304
223 = 8,388,608
224 = 16,777,216
ORDERING INFORMATION
Package
Shipping†
MC14521BDG
SOIC−16
(Pb−Free)
48 Units / Rail
NLV14521BDG*
SOIC−16
(Pb−Free)
48 Units / Rail
MC14521BDR2G
SOIC−16
(Pb−Free)
2500 / Tape & Reel
NLV14521BDR2G*
SOIC−16
(Pb−Free)
2500 / Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
2
MC14521B
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
− 55_C
25_C
VDD
Characteristic
Output Voltage
Vin = VDD or 0
“0” Level
“1” Level
Vin = 0 or VDD
Input Voltage
“0” Level
(VO = 4.5 or 0.5 Vdc)
(VO = 9.0 or 1.0 Vdc)
(VO = 13.5 or 1.5 Vdc)
“1” Level
(VO = 0.5 or 4.5 Vdc)
(VO = 1.0 or 9.0 Vdc)
(VO = 1.5 or 13.5 Vdc)
125_C
Symbol
Vdc
Min
Max
Min
Typ
(Note 2)
Max
Min
Max
Unit
VOL
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
VOH
5.0
10
15
4.95
9.95
14.95
−
−
−
4.95
9.95
14.95
5.0
10
15
−
−
−
4.95
9.95
14.95
−
−
−
Vdc
5.0
10
15
−
−
−
1.5
3.0
4.0
−
−
−
2.25
4.50
6.75
1.5
3.0
4.0
−
−
−
1.5
3.0
4.0
5.0
10
15
3.5
7.0
11
−
−
−
3.5
7.0
11
2.75
5.50
8.25
−
−
−
3.5
7.0
11
−
−
−
5.0
10
15
–0.25
–0.62
–1.8
−
−
−
–0.2
–0.5
–1.5
–0.36
–0.9
–3.5
−
−
−
–0.14
–0.35
–1.1
−
−
−
5.0
5.0
10
15
–3.0
–0.64
–1.6
–4.2
−
−
−
−
–2.4
–0.51
–1.3
–3.4
–4.2
–0.88
–2.25
–8.8
−
−
−
−
–1.7
–0.36
–0.9
–2.4
−
−
−
−
mAdc
VIL
Vdc
VIH
Vdc
Output Drive Current
(VOH = 4.5 Vdc)
Source
(VOH = 9.0 Vdc)
Pin 4
(VOH = 13 Vdc)
(VOH = 2.5 Vdc)
Source
(VOH = 4.6 Vdc) Pins 1, 7, 10,
(VOH = 9.5 Vdc) 11, 12, 13, 14
and 15
(VOH = 13.5 Vdc)
(VOL = 0.4 Vdc)
Sink
(VOL = 0.5 Vdc)
(VOL = 1.5 Vdc)
IOH
IOL
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
mAdc
Input Current
Iin
15
−
±0.1
−
±0.00001
±0.1
−
±1.0
mAdc
Input Capacitance
(Vin = 0)
Cin
−
−
−
−
5.0
7.5
−
−
pF
Quiescent Current
(Per Package)
IDD
5.0
10
15
−
−
−
5.0
10
20
−
−
−
0.005
0.010
0.015
5.0
10
20
−
−
−
150
300
600
mAdc
IT
5.0
10
15
Total Supply Current (Note 3, 4)
(Dynamic plus Quiescent,
Per Package)
(CL = 50 pF on all outputs, all
buffers switching)
mAdc
IT = (0.42 mA/kHz) f + IDD
IT = (0.85 mA/kHz) f + IDD
IT = (1.40 mA/kHz) f + IDD
mAdc
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
3. The formulas given are for the typical characteristics only at 25_C.
4. To calculate total supply current at loads other than 50 pF: IT(CL) = IT(50 pF) + (CL – 50) Vfk where: IT is in mA (per package), CL in pF,
V = (VDD – VSS) in volts, f in kHz is input frequency, and k = 0.003.
http://onsemi.com
3
MC14521B
SWITCHING CHARACTERISTICS (Note 5) (CL = 50 pF, TA = 25_C)
Characteristic
Symbol
Output Rise and Fall Time (Counter Outputs)
tTLH, tTHL = (1.5 ns/pF) CL + 25 ns
tTLH, tTHL = (0.75 ns/pF) CL + 12.5 ns
tTLH, tTHL = (0.55 ns/pF) CL + 12.5 ns
tTLH, tTHL
Propagation Delay Time
Clock to Q18
tPHL, tPLH = (1.7 ns/pF) CL + 4415 ns
tPHL, tPLH = (0.66 ns/pF) CL + 1667 ns
tPHL, tPLH = (0.5 ns/pF) CL + 1275 ns
Clock to Q24
tPHL, tPLH = (1.7 ns/pF) CL + 5915 ns
tPHL, tPLH = (0.66 ns/pF) CL + 2167 ns
tPHL, tPLH = (0.5 ns/pF) CL + 1675 ns
tPHL, tPLH
Propagation Delay Time
Reset to Qn
tPHL = (1.7 ns/pF) CL + 1215 ns
tPHL = (0.66 ns/pF) CL + 467 ns
tPHL = (0.5 ns/pF) CL + 350 ns
VDD
Vdc
Min
Typ
(Note 6)
Max
5.0
10
15
−
−
−
100
50
40
200
100
80
Unit
ns
ms
5.0
10
15
−
−
−
4.5
1.7
1.3
9.0
3.5
2.7
5.0
10
15
−
−
−
6.0
2.2
1.7
12
4.5
3.5
tPHL
5.0
10
15
−
−
−
1300
500
375
2600
1000
750
tWH(cl)
5.0
10
15
385
150
120
140
55
40
−
−
−
ns
fcl
5.0
10
15
−
−
−
3.5
9.0
12
2.0
5.0
6.5
MHz
tTLH, tTHL
5.0
10
15
−
−
−
−
−
−
15
5.0
4.0
ms
tWH(R)
5.0
10
15
1400
600
450
700
300
225
−
−
−
ns
trem
5.0
10
15
30
0
– 40
–200
–160
–110
−
−
−
ns
Clock Pulse Width
Clock Pulse Frequency
Clock Rise and Fall Time
ns
Reset Pulse Width
Reset Removal Time
5. The formulas given are for the typical characteristics only at 25_C.
6. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
VDD
500 mF
VDD
PULSE
GENERATOR
0.01 mF
CERAMIC
ID
IN 2
R
VSS
VDD
Q18
Q19
Q20
Q21
Q22
Q23
Q24
CL
CL
Vin
CL
20 ns
90%
50%
10%
50% DUTY CYCLE
CL
CL
CL
CL
VSS
Figure 1. Power Dissipation Test Circuit and Waveform
http://onsemi.com
4
20 ns
VDD
0V
MC14521B
VDD
VDD′
VDD
PULSE
GENERATOR
IN 2
R
20 ns
CL
CL
tWL
CL
CL
Qn
CL
50%
20 ns
90%
50%
10%
CL
VSS′
VSS
20 ns
IN 2
Q18
Q19
Q20
Q21
Q22
Q23
Q24
tWH
90%
10%
tPLH
tTLH
CL
tPHL
tTHL
Figure 2. Switching Time Test Circuit and Waveforms
500 kHz
Circuit
50 kHz
Circuit
Unit
Crystal Characteristics
Resonant Frequency
Equivalent Resistance, RS
500
1.0
50
6.2
kHz
kW
External Resistor/Capacitor Values
Ro
CT
CS
47
82
20
750
82
20
kW
pF
pF
+ 6.0
+ 2.0
+ 2.0
+ 2.0
ppm
ppm
– 4.0
+ 100
– 2.0
+ 120
ppm
ppm
– 2.0
– 160
– 2.0
– 560
ppm
ppm
Characteristic
VDD
Ro
18 M
CS
CT
VDD
R*
VDD′
IN 1 OUT 1
OUT 2
Q18
Q19
IN 2
Q20
Q21
Q22
Q23
R
Q24
VSS
VSS′
R*
*Optional for low power operation,
10 kW ≤ R ≤ 70 kW.
Figure 3. Crystal Oscillator Circuit
Frequency Stability
Frequency Change as a Function
of VDD (TA = 25_C)
VDD Change from 5.0 V to 10 V
VDD Change from 10 V to 15 V
Frequency Change as a Function
of Temperature (VDD = 10 V)
TA Change from – 55_C to + 25_C
MC14521 only
Complete Oscillator*
TA Change from + 25_C to + 125_C
MC14521 only
Complete Oscillator*
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
*Complete oscillator includes crystal, capacitors, and resistors.
Figure 4. Typical Data for Crystal Oscillator Circuit
http://onsemi.com
5
MC14521B
100
FREQUENCY DEVIATION (%)
VDD = 15 V
4.0
f, OSCILLATOR FREQUENCY (kHz)
8.0
TEST CIRCUIT
FIGURE 7
0
10 V
-4.0
-8.0
5.0 V
-12
f AS A FUNCTION
OF RTC
(C = 1000 pF)
(RS ≈ 2RTC)
20
10
5.0
2.0
1.0
TEST CIRCUIT
FIGURE 7
VDD = 10 V
50
f AS A FUNCTION
OF C
(RTC = 56 kW)
(RS = 120 k)
0.5
0.2
RTC = 56 kW,
C = 1000 pF
-16
-55
{
RS = 0, f = 10.15 kHz @ VDD = 10 V, TA = 25°C
RS = 120 kW, f = 7.8 kHz @ VDD = 10 V, TA = 25°C
0.1
1.0 k
-25
0
25
50
75
100
TA, AMBIENT TEMPERATURE (°C), DEVICE ONLY
0.0001
Figure 5. RC Oscillator Stability
RS
RTC
10 k
100 k
RTC, RESISTANCE (OHMS)
0.001
0.01
C, CAPACITANCE (mF)
125
1.0 m
0.1
Figure 6. RC Oscillator Frequency as a
Function of RTC and C
VDD
VDD
C
VDD′
VDD
IN 1
IN 2
R
VDD′
IN 1
OUT 1
OUT 2
Q18
Q19
Q20
Q21
Q22
Q23
Q24
VSS
Q18
Q19
Q20
Q21
IN 2
Q22
Q23
Q24
OUT 1
R
OUT 2
PULSE
GENERATOR
VSS
VSS′
Figure 7. RC Oscillator Circuit
VSS
Figure 8. Functional Test Circuit
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
FUNCTIONAL TEST SEQUENCE
Inputs
A test function (see Figure 8) has been included
for the reduction of test time required to exercise all
24 counter stages. This test function divides the
counter into three 8−stage sections, and 255
counts are loaded in each of the 8−stage sections
in parallel. All flip−flops are now at a logic “1”. The
counter is now returned to the normal 24−stages in
series configuration. One more pulse is entered into
Input 2 (In 2) which will cause the counter to ripple
from an all “1” state to an all “0” state.
Outputs
Comments
Reset
In 2
Out 2
VSS′
VDD′
Q18
thru
Q24
1
0
0
VDD
GND
0
0
1
1
First “0” to “1” transition on In 2,
Out 2 node.
0
1
−
−
−
0
1
−
−
−
255 “0” to “1” transitions are clocked
into this In 2, Out 2 node.
1
1
1
0
0
0
0
1
1
1
0
1
0
0
1
GND
http://onsemi.com
6
VDD
Counter is in three 8−stage sections
in parallel mode Counter is reset. In 2
and Out 2 are connected together.
The 255th “0” to “1” transition.
1
Counter converted back to 24−stages
in series mode.
1
Out 2 converts back to an output.
0
Counter ripples from an all “1” state
to an all “0” stage.
MC14521B
LOGIC DIAGRAM
VDD
5
RESET
2
9
1
2
IN 1
3
VSS
9
17
18
19
10
Q18
8
4
OUT 2
6
IN 2
7
OUT 1
STAGES
3 THRU 7
20
11
Q19
21
12
Q20
22
10
23
13
Q21
14
Q22
16
24
15
Q23
http://onsemi.com
7
STAGES
11 THRU 15
1
Q24
VDD = PIN 16
VSS = PIN 8
MC14521B
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
−A−
16
9
−B−
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
S
SOLDERING FOOTPRINT
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
8
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC14521B/D