NCS2553 D

NCS2553
3-Channel Video Amp with
Standard Definition
Reconstruction Filters
Description
The NCS2553 is a 3−channel high speed video amplifier with 6th
order butterworth standard definition reconstruction filter.
All three channels can accommodate either all component and RGB
video signals or composite and S−Video signals. All channels can
accept DC or AC coupled signals. If AC coupled, the internal clamps
are employed. The outputs can drive both AC and DC coupled 150 W
loads.
It is designed to be compatible with most digital−to−analog
converters (DAC) embedded in most video processors.
Feature
•
•
•
•
•
•
•
•
Three 6th Order Standard Definition 8 MHz Filters
Internally Fixed Gain = 6 dB
AC− or DC− Coupled Inputs
AC− or DC− Coupled Outputs
Integrated Level Shifter
Operating Voltage +5 V
Available in a SOIC−8 Package
These are Pb−Free Devices
MARKING
DIAGRAM
8
8
1
SOIC−8 NB
D SUFFIX
CASE 751
A
L
Y
W
G
N2553
ALYW
G
1
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
PINOUT
8 SD OUT1
SD IN1 1
Applications
•
•
•
•
•
http://onsemi.com
SD IN2 2
Digital Set−Top Box
DVD / Video Players and Related
SD−TV
Video On Demand (VOD)
Video Recorders
NCS2553
SOIC−8
SD IN3 3
7 SD OUT2
6 SD OUT3
VCC 4
5 GND
ORDERING INFORMATION
Package
Shipping†
NCS2553DG
SOIC−8
(Pb−Free)
98 Units / Rail
NCS2553DR2G
SOIC−8
(Pb−Free)
2500 / Tape & Reel
Device
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2008
December, 2008 − Rev. 4
1
Publication Order Number:
NCS2553/D
NCS2553
SD IN1
Transparent Clamp
6dB
SD OUT1
6dB
SD OUT2
6dB
SD OUT3
8 MHz, 6th Order
Transparent Clamp
SD IN2
8 MHz, 6th Order
Transparent Clamp
SD IN3
8 MHz, 6th Order
Figure 1. Block Diagram
PIN FUNCTION AND DESCRIPTION
Pin
Name
Type
Description
1
IN1
Input
Video Input 1 for Video Signal featuring a frequency bandwidth compatible with Standard Definition
Video (8 MHz) − Channel 1
2
IN2
Input
Video Input 2 for Video Signal featuring a frequency bandwidth compatible with Standard Definition
Video (8 MHz) − Channel 2
3
IN3
Input
Video Input 3 for Video Signal featuring a frequency bandwidth compatible with Standard Definition
Video (8 MHz) − Channel 3
4
VCC
Power
Device Power Supply Voltage: +5 V
5
GND
GND
Connected to Ground
6
OUT3
Output
SD Video Output 3 − Channel 3
7
OUT2
Output
SD Video Output 2 − Channel 2
8
OUT1
Output
SD Video Output 1 − Channel 1
ATTRIBUTES
Characteristics
ESD
Human Body Model
Machine Model
Value
All Pins (Note 1)
Pins 1 to 5 (Note 2)
All Output Pins (Note 2)
8 kV
400 V
800 V
Moisture Sensitivity (Note 3)
Level 1
Flammability Rating − Oxygen Index: 28 to 34
UL 94 V−0 @ 0.125 in
1. Human Body Model (HBM): R = 1500 W, C = 100 pF
2. Machine Model (MM)
3. For additional information, see Application Note AND8003/D.
http://onsemi.com
2
NCS2553
MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
VCC
−0.35 v VCC v 5.5
Vdc
Input Voltage Range
VI
−0.3 v VI v VCC
Vdc
Input Differential Voltage Range
VID
VI v VCC
Vdc
Output Current
IO
50
mA
Maximum Junction Temperature (Note 4)
TJ
150
°C
Power Supply Voltages
Operating Ambient Temperature
TA
−40 to +85
°C
Storage Temperature Range
Tstg
−60 to +150
°C
Power Dissipation
PD
(See Graph)
mW
RqJA
112.7
°C/W
Thermal Resistance, Junction−to−Air
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
4. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded.
1800
The maximum power that can be safely dissipated is
limited by the associated rise in junction temperature.
For the plastic packages, the maximum safe junction
temperature is 150°C. If the maximum is exceeded
momentarily, proper circuit operation will be restored as
soon as the die temperature is reduced. Leaving the device
in the “overheated” condition for an extended period can
result in device burnout. To ensure proper operation, it is
important to observe the de−rating curves.
1600
POWER DISSIPATION (mW)
Maximum Power Dissipation
1400
1200
1000
800
600
400
200
0
−40 −30−20−10
0 10 20 30 40 50 60 70 80 90100
TEMPERATURE (°C)
Figure 2. Power Dissipation vs Temperature
http://onsemi.com
3
NCS2553
DC ELECTRICAL CHARACTERISTICS (VCC = +5.0 V, TA = 25°C, 0.1 mF AC coupled inputs, Rsource = 37.5 W, 220 mF AC
coupled outputs into 150 W load, referenced to 400 kHz, unless otherwise specified)
Symbol
Characteristics
VCC
Supply Voltage Range
ICC
Power Supply Current
VIN
Input Common Mode Voltage Range
PSRR
Power Supply Rejection
Conditions
Min
Typ
Max
Unit
4.75
5.0
5.25
V
23
30
mA
No Load
Referenced to GND if DC−Coupled
GND
DC (All Channels)
1.4
−50
dB
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
AC ELECTRICAL CHARACTERISTICS (VCC = +5.0 V, TA = 25°C, 0.1 mF AC coupled inputs, Rsource = 37.5 W,220 mF AC
coupled outputs into 150 W load, referenced to 400 kHz, unless otherwise specified)
Symbol
Characteristics
AVOL
Voltage Gain (Note 5)
BW
Low Pass Filter Bandwidth
Conditions
Min
Typ
Max
Unit
VIN = 1 V (All Channels)
5.8
6.0
6.2
dB
−1 dB (Note 6)
5.5
7.2
MHz
−3 dB
9.0
MHz
at 27 MHz
45
dB
0.3
%
AR
Stop−Band Attenuation (Rejection)
dG
Differential Gain
dq
Differential Phase
0.6
_
THD
Total Harmonic Distortion
VOUT = 1.8 VPP @ 1 MHz
0.4
%
Xtalk
Channel−to−Channel Crosstalk
VOUT = 1.8 VPP @ 1 MHz
−60
dB
SNR
Signal−to−Noise Ratio
NTSC−7, 100 kHz to 4.2 MHz
(Note 7)
75
dB
Tpd
Propagation Delay
Input−to−Output, 4.5 MHz
60
nsec
DGD
Group Delay Variation from 100 kHz to
8 MHz
27
ns
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
5. 100% of tested IC fit to the bandwidth tolerance.
6. Guaranteed by design and characterization.
7. SNR = 20 x log (714 mV/RMS Noise)
http://onsemi.com
4
NCS2553
TYPICAL CHARACTERISTICS
VCC = +5.0 V, Rsource = 37.5 W, TA = 25°C, 0.1 mF AC−coupled inputs, 220 mF AC−coupled outputs into 150 W referenced to 400 kHz, all
channels, unless otherwise specified
−35
6.7 MHz,
−0.5 dB
6 dB
9.0 MHz,
−3 dB
0
GAIN (dB)
−10
−45
7.2 MHz,
−1 dB
−20
−30
−40
−50
27 MHz Stop−band Rejection
= 46 dB
(6 dB − (−40 dB))
−60
−70
Vin = 4 dBm
Zout = 150 W
−80
0.01
0.1
1
10
6.7 MHz,
−43 dB
−40
−50
CROSSTALK (dB)
20
10
−55
−60
1 MHz,
−60 dB
−65
−70
−75
−80
−85
100k
100
Vin = 4 dBm
Zout = 150 W
8M
1M
FREQUENCY (MHz)
FREQUENCY (Hz)
Figure 3. Frequency Response
Figure 4. Channel−to−Channel Crosstalk
110
70
60
50
40
20
10
100k
3.0
1.5
2.6
1.25
0.75
1.2
79 ns
0.5
0.8
Output
0.25
0.4
0
−0.75
1M
10M
30M
0
−0.4
50
100 150 200
250 300
350 400 450 500
FREQUENCY (Hz)
TIME (ns)
Figure 5. Group Delay
Figure 6. Propagation Delay
−45
−45
−50
−50
−55
−55
−60
−60
−65
−65
−70
−75
−80
−70
−75
−80
−85
−95
100k
1.6
0
Vin = 4 dBm
Zout = 150 W
−90
2.0
Input
1.0
OUTPUT VOLTAGE (V)
80
30
PSRR (dB)
INPUT VOLTAGE (V)
90
1.75
PSRR (dB)
GROUP DELAY (ns)
100
−85
Vin = −22 dBm
Zout = 150 W
−90
1M
10M
−95
100k
50M
FREQUENCY (Hz)
Vin = −22 dBm
Zout = 150 W
1M
FREQUENCY (Hz)
10M
Figure 8. PSRR vs. Frequency
(Bypass Capacitor)
Figure 7. PSRR vs Frequency
(No Bypass Capacitor)
http://onsemi.com
5
50M
NCS2553
TYPICAL CHARACTERISTICS
VCC = +5.0 V, Rsource = 37.5 W, TA = 25°C, 0.1 mF AC−coupled inputs, 220 mF AC−coupled outputs into 150 W referenced to 400 kHz, all
channels, unless otherwise specified
6.4
6.2
GAIN (dB)
3.8 MHz,
6.19 dB
400 kHz,
6.04 dB
6
5.5 MHz,
6.00 dB
5.8
5.6
5.4
0.01
6.7 MHz,
5.5 dB
Vin = 4 dBm
Zout = 150 W
0.1
1
FREQUENCY (Hz)
10
Figure 9. Gain Flatness
0.5
1.2
0.46
0.35
0.35
0.3
0.3
0.25
0.18
0.2
0.15
0.1
0
0.04
2
0.81
0.8
0.61
0.6
0.6
0.44
0.4
0.2
0
0
1
0.96
1
3
4
5
0
6
1
2
3
4
5
6
HARMONIC NUMBERS
HARMONIC NUMBERS
Figure 10. Differential Gain (NTSC 5 Steps
Input Signal)
Figure 11. Differential Phase (NTSC 5 Steps
Input Signal
120
20
Gain
105
10
90
0
75
−10
60
−20
45
−30
Group Delay
30
−40
15
−50
0
−60
−15
−70
−30
20k
100k
1M
FREQUENCY (Hz)
10M
GAIN (dB)
0.05
DIFFERENTIAL PHASE (°)
0.4
GROUP DELAY (ns)
DIFFERENTIAL GAIN (%)
0.45
−80
40M
Figure 12. Normalized Frequency Response and Group Delay vs. Frequency
http://onsemi.com
6
NCS2553
APPLICATIONS INFORMATION
and allows DC−coupled output to the 150 W video load. In
addition, the NCS2553 integrates a 6th order Butterworth
filter per channel with a 3 dB frequency bandwidth of 8
MHz. This allows rejecting out the aliases or unwanted
over−sampling effects produced by the video DAC.
Similarly, in the case of DVD recorders using ADC, this
anti−aliasing filter (reconstruction filter) will avoid picture
quality issues and will help to filter out parasitic signals
caused by EMI interference.
A built−in diode−like clamp is used in the chip for each
channel to support AC−coupled mode of operation. The
clamp is active when the input signal goes below 0 V.
The NCS2553 triple video driver has been optimized for
Standard Definition video applications covering the
requirements of the CVBS, S−Video, 480i/525i & 576i/625i
standards. All the 3 channels feature the same specifications
and similar behaviors guaranteed by a high channel−to−
channel crosstalk isolation (down to 60 dB at 1 MHz). Each
channel provides an internal voltage−to−voltage gain of 2
from its input to its output reducing the number of external
components usually needed in the case of some discrete
approaches (using stand−alone op amps). An internal level
shifter is employed shifting up the output voltage by adding
an offset of about 280 mV. This avoids sync pulse clipping
2.28V
1V
Y, R’, G’, B’
1VPP
0V
0.1mF
IN1
Clamp
0.28V
220mF
LS 8MHz
75W
OUT1
0.1mF
IN2
DAC
Clamp
800k
RS
0.1mF
IN3
Clamp
800k
RS
6db
220mF
LS 8MHz
6db
280mV
LS 8MHz
220mF
280mV
6db
ZO = 75W
75W
ZO = 75W
75W
ZO = 75W
75W
75W
OUT2
OUT3
800k
RS
280mV
75W
1.68V
0.7V
Pb, Pr
0V
0.28V
0.7VPP
Figure 13. AC−Coupled Inputs and Outputs
The input is AC−coupled if for example the input−signal
amplitude goes over the range 0 to 1.4 V or if the video
source requires such a coupling. In some circumstances it
may be necessary to auto−bias signals by the addition of a
pull−up and pull−down resistor or only pull−up resistor
(Typical 7.5 MW combined with the internal 800 kW
pull−down) making the clamp inactive.
The output AC−coupling configuration has the advantage
of eliminating DC ground loop with the drawback of making
the device more sensitive to video line or field tilt issues in
the case of a too low output coupling capacitor. In some
cases it may be necessary to increase the nominal 220 mF
capacitor value.
Figure 13 shows an example for which the external video
source coming from the DAC is AC−coupled at the input and
output. But thanks to the built−in transparent clamp and
level shifter the device can operate in different configuration
modes depending essentially on the DAC output signal level
High and Low and how it fits the input common mode
voltage of the video driver. When the configuration is
DC−Coupled at the Inputs and Outputs the 0.1 mF and
220 mF coupling capacitors are no longer used, the clamps
are in that case inactive; this configuration has the big
advantage of being relatively low cost with the use of less
external components.
http://onsemi.com
7
NCS2553
DVD Player or STB
+5 V
0.1 mF
1
R/Pr
10 mF
IN1
OUT1
8
Video
SOC
2
IN2
OUT2
NCS2553
RS
3
B/Pd
RS
R/Pr
75 W
RS
G/Y
75 W 220 mF 75 W Video Cables
IN3
OUT3
7
75 W 220 mF 75 W Video Cables
G/Y
75 W
6
75 W 220 mF 75 W Video Cables
B/Pd
75 W
4
VCC
GND
5
DAC Load Resistors
AC−Coupling Caps
are Optional
Figure 14. Typical Application Circuit
http://onsemi.com
8
NCS2553
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AJ
−X−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
−Y−
K
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
D
0.25 (0.010)
M
Z Y
S
X
M
J
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
9
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCS2553/D