EMI4183 D

EMI4183
Common Mode Filter with
ESD Protection
Functional Description
The EMI4183 is an integrated common mode filter providing both
ESD protection and EMI filtering for high speed digital serial
interfaces such as MIPI D-PHY.
The EMI4183 provides protection for three differential data line
pairs in a small RoHS-compliant WDFN16 package.
http://onsemi.com
MARKING
DIAGRAMS
4TMG
G
Features
• Highly Integrated Common Mode Filter (CMF) with ESD Protection
•
•
•
•
•
•
provides protection and EMI reduction for systems using High Speed
Serial Data Lines with cost and space savings over discrete solutions
Large Differential Mode Bandwidth with Cutoff Frequency > 2 GHz
High Common Mode Stop Band Attenuation: >25 dB at 700 MHz,
>30 dB at 800 MHz
Provides ESD Protection to IEC61000-4-2 Level 4, ±15 kV Contact
Discharge
Low Channel Input Capacitance Provides Superior Impedance
Matching Performance
Low Profile Package with Small Footprint in WDFN16 2 x 4 mm
Pb−Free Package
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
Applications
• MIPI D-PHY (CSI-2, DSI, etc) in Mobile Phones and Digital Still
Cameras
WDFN16
CASE 511BL
4T = Specific Device Code
M = Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
In_1+
1
16
Out_1+
In_1−
2
15
Out_1−
GND
3
14
GND
In_2+
4
13
Out_2+
In_2−
5
12
Out_2−
GND
6
11
GND
1
16
In_3+
7
10
Out_3+
2
15
In_3−
8
9
Out_3−
4
External
(Connector) 5
13
7
10
8
9
(Top View)
12
Internal
(ASIC)
3, 14
ORDERING INFORMATION
Device
Package
Shipping†
EMI4183MTTAG
WDFN16
(Pb−Free)
3000/Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
6, 11
Figure 1. EMI4183 Electrical Schematic
© Semiconductor Components Industries, LLC, 2011
October, 2011 − Rev. 1
1
Publication Order Number:
EMI4183/D
EMI4183
PIN FUNCTION DESCRIPTION
Pin Name
Pin No.
Type
In_1+
1
I/O
CMF Channel 1+ to Connector (External)
Description
In_1−
2
I/O
CMF Channel 1− to Connector (External)
Out_1+
16
I/O
CMF Channel 1+ to ASIC (Internal)
Out_1−
15
I/O
CMF Channel 1− to ASIC (Internal)
In_2+
4
I/O
CMF Channel 2+ to Connector (External)
In_2−
5
I/O
CMF Channel 2− to Connector (External)
Out_2+
13
I/O
CMF Channel 2+ to ASIC (Internal)
Out_2−
12
I/O
CMF Channel 2− to ASIC (Internal)
In_3+
7
I/O
CMF Channel 3+ to Connector (External)
In_3−
8
I/O
CMF Channel 3− to Connector (External)
Out_3+
10
I/O
CMF Channel 3+ to ASIC (Internal)
CMF Channel 3− to ASIC (Internal)
Out_3−
9
I/O
GND
3, 14
GND
Ground
GND
6, 11
GND
Ground
ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Parameter
Symbol
Value
Unit
Operating Temperature Range
TOP
−40 to +85
°C
Storage Temperature Range
TSTG
−65 to +150
°C
TL
260
°C
ILINE
100
mA
Maximum Lead Temperature for Soldering Purposes
(1/8” from Case for 10 seconds)
DC Current per Line
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
2
EMI4183
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Symbol
Parameter
Test Conditions
ILEAK
Channel Leakage Current
TA = 25°C, VIN = 5 V, GND = 0 V
VF
Channel Negative Voltage
TA = 25°C, IF = 10 mA
CIN
Channel Input Capacitance to Ground
(Pins 1,2,4,5,7,8 to Pins 3,6,11,14)
TA = 25°C, At 1 MHz, GND = 0 V,
VIN = 1.65 V
RCH
Channel Resistance
(Pins 1−16, 2−15, 4−13, 5−12, 7−10 & 8−9)
f3dB
Differential Mode Cut−off Frequency
Fatten
VESD
Min
Typ
0.1
0.8
Max
Unit
1.0
mA
1.5
V
1.3
pF
8.0
W
50 W Source and Load Termination
2.0
GHz
Common Mode Stop Band Attenuation
@ 800 MHz
30
dB
In−system ESD Withstand Voltage
a) Contact discharge per IEC 61000−4−2
standard, Level 4 (External Pins)
b) Contact discharge per IEC 61000−4−2
standard, Level 1 (Internal Pins)
(Notes 1 and 2)
TLP Clamping Voltage
(See Figure 12)
Forward IPP = 8 A
Forward IPP = 16 A
Forward IPP = −8 A
Forward IPP = −16 A
12
18
−6
−12
RDYN
Dynamic Resistance
Positive Transients
Negative Transients
TA = 25°C, IPP = 1 A, tP = 8/20 ms
Any I/O pin to Ground;
Notes 1 and 3
1.36
0.6
VRWM
Reverse Working Voltage
(Note 3)
Breakdown Voltage
IT = 1 mA; (Note 4)
VCL
VBR
kV
±15
±2
5.6
V
V
V
V
5.0
V
9.0
V
1. Standard IEC61000−4−2 with CDischarge = 150 pF, RDischarge = 330, GND grounded.
2. These measurements performed with no external capacitor.
3. TVS devices are normally selected according to the working peak reverse voltage (VRWM), which should be equal to or greater than the DC
or continuous peak operating voltage level.
4. VBR is measured at pulse test current IT.
http://onsemi.com
3
EMI4183
TYPICAL CHARACTERISTICS
Figure 2. Differential Mode Attenuation vs.
Frequency (Zdiff = 100 W)
Figure 3. Common Mode Attenuation vs.
Frequency (Zcomm = 50 W)
Figure 4. Differential Return Loss vs. Frequency
(Zdiff=100 W)
Figure 5. Differential Inter−Lane Cross−Coupling
Figure 6. Common Mode Inter−Lane Cross−Coupling
http://onsemi.com
4
EMI4183
MIPI DSI (D−PHY)
Host
MIPI DSI (D−PHY)
Client
EMI4183
Evaluation
Board
Figure 7. MIPI D−PHY LP Mode Test Setup
Figure 8. EMI4183 MIPI D−PHY LP Mode Measured Results
http://onsemi.com
5
EMI4183
Figure 9. EMI4183 Eye Diagram Test Setup
Figure 10. EMI4183 Measured Eye Diagram @ 3.4Gbps (EVB through on left, EVB with EMI4183 on right)
http://onsemi.com
6
EMI4183
Transmission Line Pulse (TLP) Measurements
Transmission Line Pulse (TLP) provides current versus voltage (I-V) curves in which each data point is obtained from a
100 ns long rectangular pulse from a charged transmission line. A simplified schematic of a typical TLP system is shown in
Figure 11. TLP I-V curves of ESD protection devices accurately demonstrate the product’s ESD capability because the 10 s
of amps current levels and under 100 ns time scale match those of an ESD event. This is illustrated in Figure 12 where an 8 kV
IEC61000-4-2 current waveform is compared with TLP current pulses at 8 and 16 A. A TLP curve shows the voltage at which
the device turns on as well as how well the device clamps voltage over a range of current levels. Typical TLP I-V curves for
the EMI4183 are shown in Figure 13.
L
SW
50 W Coax
Cable
Attenuator
50 W Coax Cable
÷
IM
VM
10 MW
VC
DUT
Oscilloscope
Figure 11. Simplified Schematic of a Typical TLP System
Figure 12. Comparison Between 8 kV IEC61000−4−2 and 8 A and 16 A TLP Waveforms
Figure 13. Positive and Negative TLP Waveforms
http://onsemi.com
7
EMI4183
ESD Voltage Clamping
For sensitive circuit elements it is important to limit the voltage that an IC will be exposed to during an ESD event to as low
a voltage as possible. The ESD clamping voltage is the voltage drop across the ESD protection diode during an ESD event per
the IEC61000−4−2 waveform. Since the IEC61000−4−2 was written as a pass/fail spec for larger systems such as cell phones
or laptop computers it is not clearly defined in the spec how to specify a clamping voltage at the device level. ON Semiconductor
has developed a way to examine the entire voltage waveform across the ESD protection diode over the time domain of an ESD
pulse in the form of an oscilloscope screenshot, which can be found on the datasheets for all ESD protection diodes. For more
information on how ON Semiconductor creates these screenshots and how to interpret them please refer to On Semiconductor
Application Notes AND8307/D and AND8308/D.
IEC61000−4−2 Waveform
IEC61000−4−2 Spec.
Ipeak
Level
Test
Voltage
(kV)
First Peak
Current
(A)
Current at
30 ns (A)
Current at
60 ns (A)
1
2
7.5
4
2
2
4
15
8
4
3
6
22.5
12
6
4
8
30
16
8
100%
90%
I @ 30 ns
I @ 60 ns
10%
tP = 0.7 ns to 1 ns
Oscilloscope
TVS
50 W
Cable
50 W
Figure 14. Diagram of ESD Test Setup
100
% OF PEAK PULSE CURRENT
ESD Gun
PEAK VALUE IRSM @ 8 ms
tr
90
PULSE WIDTH (tP) IS DEFINED
AS THAT POINT WHERE THE
PEAK CURRENT DECAY = 8 ms
80
70
60
HALF VALUE IRSM/2 @ 20 ms
50
40
30
tP
20
10
0
0
20
40
t, TIME (ms)
60
Figure 15. 8 x 20 ms Pulse Waveform
http://onsemi.com
8
80
EMI4183
Figure 16. ESD Clamping Voltage +8 kV per IEC6100−4−2 (external to internal pin)
Figure 17. ESD Clamping Voltage −8 kV per IEC6100−4−2 (external to internal pin)
D−PHY (CDI/DSI)
Transmitter
D0+
EMI4183
D−PHY (CSI/DSI)
Receiver
D0+
D0GND
D0GND
D0+
D0-
D0+
D0-
GND
GND
Clock+
Clock-
Clock+
Clock(Top View)
Figure 18. EMI4183 MIPI D−PHY Application Diagram
http://onsemi.com
9
EMI4183
PACKAGE DIMENSIONS
WDFN16 4x2, 0.5P
CASE 511BL−01
ISSUE O
2X
0.10 C
PIN 1
REFERENCE
0.10 C
2X
E
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
ÉÉ
ÇÇ
EXPOSED Cu
TOP VIEW
(A3)
DETAIL B
A
MOLD CMPD
A1
ÇÇ
ÉÉ
DIM
A
A1
A3
b
D
E
e
L
L1
ALTERNATE
CONSTRUCTIONS
A1
SIDE VIEW
A3
DETAIL B
0.05 C
NOTE 4
C
SEATING
PLANE
8
13X
12X
12X
MILLIMETERS
MIN
MAX
0.70
0.80
0.00
0.05
0.20 REF
0.15
0.25
4.00 BSC
2.00 BSC
0.50 BSC
0.70
0.90
0.05
0.15
RECOMMENDED
MOUNTING FOOTPRINT*
DETAIL A
1
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSIONS b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L1
ÇÇÇÇ
ÇÇÇÇ
0.05 C
L
L
A B
D
0.30
1.07
L
PACKAGE
OUTLINE
0.10
MIN
16
e
2.30
9
14X
e/2
BOTTOM VIEW
1
b
0.10
M
C A B
0.05
M
C
0.45
NOTE 3
0.50 PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
10
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
EMI4183/D