MC74LVXT8053 D

MC74LVXT8053
Analog Multiplexer/
Demultiplexer
High−Performance Silicon−Gate CMOS
The MC74LVXT8053 utilizes silicon−gate CMOS technology to
achieve fast propagation delays, low ON resistances, and low OFF
leakage currents. This analog multiplexer/demultiplexer controls
analog voltages that may vary across the complete power supply range
(from VCC to GND).
The LVXT8053 is similar in pinout to the high−speed HC4053A,
and the metal−gate MC14053B. The Channel−Select inputs determine
which one of the Analog Inputs/Outputs is to be connected by means
of an analog switch to the Common Output/Input. When the Enable
pin is HIGH, all analog switches are turned off.
The Channel−Select and Enable inputs are compatible with
TTL−type input thresholds. The input protection circuitry on this
device allows overvoltage tolerance on the input, allowing the device
to be used as a logic−level translator from 3.0 V CMOS logic to 5.0 V
CMOS Logic or from 1.8 V CMOS logic to 3.0 V CMOS Logic while
operating at the higher−voltage power supply.
The MC74LVXT8053 input structure provides protection when
voltages up to 7.0 V are applied, regardless of the supply voltage. This
allows the MC74LVXT8053 to be used to interface 5.0 V circuits to
3.0 V circuits.
This device has been designed so that the ON resistance (Ron) is
more linear over input voltage than Ron of metal−gate CMOS analog
switches.
http://onsemi.com
SOIC−16
D SUFFIX
CASE 751B
TSSOP−16
DT SUFFIX
CASE 948F
PIN ASSIGNMENT
VCC
Y
X
X1
X0
A
B
C
16
15
14
13
12
11
10
9
6
7
8
1
2
3
4
5
Y1
Y0
Z1
Z
Z0 Enable NC GND
MARKING DIAGRAMS
16
LVXT8053G
AWLYWW
Features
•
•
•
•
•
•
•
•
•
Fast Switching and Propagation Speeds
Low Crosstalk Between Switches
Diode Protection on All Inputs/Outputs
Analog Power Supply Range (VCC − GND) = 2.0 V to 6.0 V
Digital (Control) Power Supply Range (VCC − GND) = 2.0 V to 6.0 V
Improved Linearity and Lower ON Resistance Than Metal−Gate
Counterparts
Low Noise
In Compliance With the Requirements of JEDEC Standard No. 7A
These Devices are Pb−Free and are RoHS Compliant
1
SOIC−16
16
LVXT
8053
ALYWG
G
1
TSSOP−16
LVXT8053
A
WL, L
Y
WW, W
G or G
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
© Semiconductor Components Industries, LLC, 2014
August, 2014 − Rev. 6
1
Publication Order Number:
MC74LVXT8053/D
MC74LVXT8053
FUNCTION TABLE − MC74LVXT8053
Control Inputs
Enable
C
L
L
L
L
L
L
L
L
H
L
L
L
L
H
H
H
H
X
Select
B
A
L
L
H
H
L
L
H
H
X
L
H
L
H
L
H
L
H
X
ON Channels
Z0
Z0
Z0
Z0
Z1
Z1
Z1
Z1
Y0
Y0
Y1
Y1
Y0
Y0
Y1
Y1
NONE
X0
X1
X0
X1
X0
X1
X0
X1
X = Don’t Care
12
X0
13
X1
14
X SWITCH
2
Y0
1
Y1
ANALOG
INPUTS/OUTPUTS
15
Y SWITCH
5
Z0
3
Z1
4
Z SWITCH
X
Y
COMMON
OUTPUTS/INPUTS
Z
11
A
10
B
9
C
PIN 16 = VCC
6
PIN 8 = GND
ENABLE
NOTE: This device allows independent control of each switch. Channel−Select Input A
controls the X−Switch, Input B controls the Y−Switch and Input C controls the Z−Switch
CHANNEL‐SELECT
INPUTS
Figure 1. LOGIC DIAGRAM
Triple Single−Pole, Double−Position Plus Common Off
MAXIMUM RATINGS
Symbol
Parameter
Unit
–0.5 to +7.0
V
VCC
Positive DC Supply Voltage
VIS
Analog Input Voltage
−0.5 to VCC + 0.5
V
Vin
Digital Input Voltage (Referenced to GND)
–0.5 to VCC + 0.5
V
DC Current, Into or Out of Any Pin
−20
mA
PD
Power Dissipation in Still Air,
500
450
mW
Tstg
Storage Temperature Range
–65 to +150
°C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
260
°C
I
(Referenced to GND)
Value
SOIC Package†
TSSOP Package†
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating: SOIC Package: –7 mW/°C from 65°C to 125°C
TSSOP Package: −6.1 mW/°C from 65°C to 125°C
http://onsemi.com
2
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or V CC ).
Unused outputs must be left open.
MC74LVXT8053
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
(Referenced to GND)
2.0
6.0
V
0.0
VCC
V
GND
VCC
V
1.2
V
–55
+ 85
°C
0
0
100
20
ns/V
VCC
Positive DC Supply Voltage
VIS
Analog Input Voltage
Vin
Digital Input Voltage (Referenced to GND)
VIO*
Static or Dynamic Voltage Across Switch
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time (Channel Select or Enable Inputs)
VCC = 3.3 V ± 0.3 V
VCC = 5.0 V ± 0.5 V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*For voltage drops across switch greater than 1.2 V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may
contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
DC CHARACTERISTICS − Digital Section (Voltages Referenced to GND)
Symbol
Parameter
Condition
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
VIH
Minimum High−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
3.0
4.5
5.5
1.2
2.0
2.0
1.2
2.0
2.0
1.2
2.0
2.0
V
VIL
Maximum Low−Level Input Voltage,
Channel−Select or Enable Inputs
Ron = Per Spec
3.0
4.5
5.5
0.53
0.8
0.8
0.53
0.8
0.8
0.53
0.8
0.8
V
Iin
Maximum Input Leakage Current,
Channel−Select or Enable Inputs
Vin = VCC or GND,
5.5
±0.1
±1.0
±1.0
mA
ICC
Maximum Quiescent Supply
Current (per Package)
Channel Select, Enable and
VIS = VCC or GND; VIO = 0 V
5.5
4
40
160
mA
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
DC ELECTRICAL CHARACTERISTICS (Analog Section)
Symbol
Ron
Parameter
Maximum “ON” Resistance
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
Vin = VIL or VIH
VIS = VCC to GND
|IS| v 10.0 mA (Figures 1, 2)
3.0
4.5
5.5
40
30
25
45
32
28
50
37
30
W
Vin = VIL or VIH
VIS = VCC or GND (Endpoints)
|IS| v 10.0 mA (Figures 1, 2)
3.0
4.5
5.5
30
25
20
35
28
25
40
35
30
Test Conditions
DRon
Maximum Difference in “ON”
Resistance Between Any Two
Channels in the Same Package
Vin = VIL or VIH
VIS = 1/2 (VCC − GND)
|IS| v 10.0 mA
3.0
4.5
5.5
15
8.0
8.0
20
12
12
25
15
15
W
Ioff
Maximum Off−Channel Leakage
Current, Any One Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 3)
5.5
0.1
0.5
1.0
mA
Maximum Off−Channel
Leakage Current,
Common Channel
Vin = VIL or VIH;
VIO = VCC or GND;
Switch Off (Figure 4)
5.5
0.1
1.0
2.0
Maximum On−Channel
Leakage Current,
Channel−to−Channel
Vin = VIL or VIH;
Switch−to−Switch =
VCC or GND; (Figure 5)
5.5
0.1
1.0
2.0
Ion
http://onsemi.com
3
mA
MC74LVXT8053
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 3 ns)
VCC
V
Guaranteed Limit
−55 to 25°C
≤85°C
≤125°C
Unit
tPLH,
tPHL
Maximum Propagation Delay, Channel−Select to Analog Output
(Figure 9)
2.0
3.0
4.5
5.5
30
20
15
15
35
25
18
18
40
30
22
20
ns
tPLH,
tPHL
Maximum Propagation Delay, Analog Input to Analog Output
(Figure 10)
2.0
3.0
4.5
5.5
4.0
3.0
1.0
1.0
6.0
5.0
2.0
2.0
8.0
6.0
2.0
2.0
ns
tPLZ,
tPHZ
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
5.5
30
20
15
15
35
25
18
18
40
30
22
20
ns
tPZL,
tPZH
Maximum Propagation Delay, Enable to Analog Output
(Figure 11)
2.0
3.0
4.5
5.5
20
12
8.0
8.0
25
14
10
10
30
15
12
12
ns
Symbol
Parameter
Cin
Maximum Input Capacitance, Channel−Select or Enable Inputs
10
10
10
pF
CI/O
Maximum Capacitance
Analog I/O
35
35
35
pF
Common O/I
50
50
50
Feedthrough
1.0
1.0
1.0
(All Switches Off)
Typical @ 25°C, VCC = 5.0 V
CPD
Power Dissipation Capacitance (Figure 13)*
* Used to determine the no−load dynamic power consumption: P D = CPD VCC2 f + ICC VCC .
45
pF
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
VCC
V
Limit*
25°C
Symbol
Parameter
Condition
BW
Maximum On−Channel Bandwidth
or Minimum Frequency Response
(Figure 6)
fin = 1MHz Sine Wave; Adjust fin Voltage to Obtain 0dBm
at VOS; Increase fin Frequency Until dB Meter Reads
−3 dB;
RL = 50 W, CL = 10 pF
3.0
4.5
5.5
120
120
120
Off−Channel Feedthrough
Isolation (Figure 7)
fin = Sine Wave; Adjust fin Voltage to Obtain 0 dBm at
VIS
fin = 10kHz, RL = 600 W, CL = 50 pF
3.0
4.5
5.5
−50
−50
−50
3.0
4.5
5.5
−37
−37
−37
3.0
4.5
5.5
25
105
135
3.0
4.5
5.5
35
145
190
3.0
4.5
5.5
−50
−50
−50
3.0
4.5
5.5
−60
−60
−60
−
fin = 1.0MHz, RL = 50W, CL = 10pF
−
Feedthrough Noise.
Channel−Select Input to Common
I/O (Figure 8)
Vin ≤ 1MHz Square Wave (tr = tf = 3 ns); Adjust RL at
Setup so that IS = 0A;
Enable = GND
RL = 600 W, CL = 50pF
RL = 10 kW, CL = 10pF
−
Crosstalk Between Any Two
Switches (Figure 12)
fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS
fin = 10 kHz, RL = 600W, CL = 50pF
fin = 1.0MHz, RL = 50W, CL = 10pF
THD
Total Harmonic Distortion
(Figure 14)
fin = 1kHz, RL = 10 kW, CL = 50pF
THD = THDmeasured − THDsource
VIS = 2.0VPP sine wave
VIS = 4.0VPP sine wave
VIS = 5.0VPP sine wave
*Limits not tested. Determined by design and verified by qualification.
http://onsemi.com
4
Unit
MHz
dB
mVPP
dB
%
3.0
4.5
5.5
0.10
0.08
0.05
MC74LVXT8053
45
Ron , ON RESISTANCE (OHMS)
40
35
30
125°C
85°C
25°C
25
20
-55°C
15
10
5
00
1.0
2.0
3.0
4.0
VIN, INPUT VOLTAGE (VOLTS)
35
30
30
25
20
125°C
85°C
25°C
15
-55°C
25
Ron , ON RESISTANCE (OHMS)
Ron , ON RESISTANCE (OHMS)
Figure 1a. Typical On Resistance, VCC = 3.0 V
10
15
-55°C
10
5
5
0
20
125°C
85°C
25°C
0
1.0
2.0
3.0
4.0
0
5.0
0
1.0
2.0
VIN, INPUT VOLTAGE (VOLTS)
Figure 1b. Typical On Resistance, VCC = 4.5 V
4.0
5.0
Figure 1c. Typical On Resistance, VCC = 5.5 V
PLOTTER
PROGRAMMABLE
POWER
SUPPLY
-
3.0
VIN, INPUT VOLTAGE (VOLTS)
MINI COMPUTER
DC ANALYZER
+
VCC
DEVICE
UNDER TEST
ANALOG IN
COMMON OUT
GND
GND
Figure 1. On Resistance Test Set−Up
http://onsemi.com
5
6.0
MC74LVXT8053
VCC
VCC
VCC
16
GND
ANALOG I/O
OFF
A
VCC
VIH
OFF
VCC
COMMON O/I
OFF
NC
OFF
VIH
6
8
Figure 2. Maximum Off Channel Leakage Current,
Any One Channel, Test Set−Up
Figure 3. Maximum Off Channel Leakage Current,
Common Channel, Test Set−Up
VCC
VCC
VCC
16
A
0.1 mF
dB
METER
ON
N/C
COMMON O/I
OFF
VOS
16
fin
ON
VCC
COMMON O/I
6
8
GND
VCC
16
GND
RL
CL*
ANALOG I/O
VIL
6
6
8
8
*Includes all probe and jig capacitance
Figure 4. Maximum On Channel Leakage Current,
Channel to Channel, Test Set−Up
VCC
VIS
0.1 mF
VCC
VOS
16
fin
dB
METER
OFF
RL
Figure 5. Maximum On Channel Bandwidth,
Test Set−Up
CL*
16
RL
COMMON O/I
ON/OFF
ANALOG I/O
RL
OFF/ON
RL
RL
6
6
8
VIL or VIH
VIH
VIL
CHANNEL SELECT
Vin ≤ 1 MHz
tr = tf = 3 ns
8
TEST
POINT
CL*
VCC
11
CHANNEL SELECT
*Includes all probe and jig capacitance
*Includes all probe and jig capacitance
Figure 6. Off Channel Feedthrough Isolation,
Test Set−Up
Figure 7. Feedthrough Noise, Channel Select to
Common Out, Test Set−Up
http://onsemi.com
6
MC74LVXT8053
VCC
VCC
16
VCC
CHANNEL
SELECT
ON/OFF
50%
COMMON O/I
ANALOG I/O
OFF/ON
GND
tPLH
TEST
POINT
CL*
tPHL
6
ANALOG
OUT
50%
8
CHANNEL SELECT
*Includes all probe and jig capacitance
Figure 9a. Propagation Delays, Channel Select
to Analog Out
Figure 9b. Propagation Delay, Test Set−Up Channel
Select to Analog Out
VCC
16
VCC
ANALOG
IN
COMMON O/I
ANALOG I/O
ON
50%
TEST
POINT
CL*
GND
tPLH
tPHL
ANALOG
OUT
6
8
50%
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In
to Analog Out
tf
tr
90%
50%
10%
ENABLE
tPZL
ANALOG
OUT
tPLZ
1
VCC
GND
16
1
1kW
ANALOG I/O
TEST
POINT
ON/OFF
2
CL*
VOL
tPHZ
90%
VCC
VCC
HIGH
IMPEDANCE
10%
POSITION 1 WHEN TESTING tPHZ AND tPZH
POSITION 2 WHEN TESTING tPLZ AND tPZL
2
50%
tPZH
ANALOG
OUT
Figure 10b. Propagation Delay, Test Set−Up
Analog In to Analog Out
VIH
VIL
VOH
ENABLE
50%
6
8
HIGH
IMPEDANCE
Figure 11a. Propagation Delays, Enable to
Analog Out
Figure 11b. Propagation Delay, Test Set−Up
Enable to Analog Out
http://onsemi.com
7
MC74LVXT8053
VCC
VIS
A
VCC
16
RL
fin
16
VOS
ON/OFF
ON
COMMON O/I
NC
ANALOG I/O
0.1mF
OFF/ON
OFF
RL
RL
CL*
RL
CL*
VCC
6
6
8
8
CHANNEL SELECT
11
*Includes all probe and jig capacitance
Figure 12. Crosstalk Between Any Two
Switches, Test Set−Up
Figure 13. Power Dissipation Capacitance,
Test Set−Up
0
VIS
VCC
0.1mF
fin
ON
CL*
-20
TO
DISTORTION
METER
-30
-40
dB
RL
FUNDAMENTAL FREQUENCY
-10
VOS
16
-50
DEVICE
-60
6
SOURCE
-70
8
-80
-90
*Includes all probe and jig capacitance
- 100
1.0
2.0
3.125
FREQUENCY (kHz)
Figure 14a. Total Harmonic Distortion, Test Set−Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
connected). However, tying unused analog inputs and
outputs to VCC or GND through a low value resistor helps
minimize crosstalk and feedthrough noise that may be
picked up by an unused switch.
Although used here, balanced supplies are not a
requirement. The only constraints on the power supplies are
that:
VCC − GND = 2 to 6 volts
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external Germanium
or Schottky diodes (Dx) are recommended as shown in
Figure 16. These diodes should be able to absorb the
maximum anticipated current surges during clipping.
The Channel Select and Enable control pins should be at
VCC or GND logic levels. VCC being recognized as a logic
high and GND being recognized as a logic low. In this
example:
VCC = +5V = logic high
GND = 0V = logic low
The maximum analog voltage swing is determined by the
supply voltages VCC. The positive peak analog voltage
should not exceed VCC. Similarly, the negative peak analog
voltage should not go below GND. In this example, the
difference between VCC and GND is five volts. Therefore,
using the configuration of Figure 15, a maximum analog
signal of five volts peak−to−peak can be controlled. Unused
analog inputs/outputs may be left floating (i.e., not
http://onsemi.com
8
MC74LVXT8053
VCC
+5V
16
+5V
ANALOG
SIGNAL
0V
ANALOG
SIGNAL
ON
6
8
VCC
Dx
+5V
16
Dx
Dx
GND
GND
8
Figure 15. Application Example
Figure 16. External Germanium or
Schottky Clipping Diodes
+3V
+5V
16
+3V
ANALOG
SIGNAL
GND
ON/OFF
Dx
ON/OFF
0V
TO EXTERNAL LSTTL COMPATIBLE
CIRCUITRY 0 to VIH
DIGITAL SIGNALS
11
10
9
VCC
ANALOG
SIGNAL
+3V
+5V
GND
GND
16
ANALOG
SIGNAL
ON/OFF
+5V
ANALOG
SIGNAL
GND
1.8 - 2.5V
6
8
11
10
9
6
1.8 - 2.5V
CIRCUITRY
8
11
10
9
1.8 - 2.5V
CIRCUITRY
MC74VHC1GT50 BUFFERS
VCC = 3.0V
a. Low Voltage Logic Level Shifting Control
b. 2−Stage Logic Level Shifting Control
Figure 17. Interfacing Low Voltage CMOS Inputs
A
11
13
LEVEL
SHIFTER
12
14
B
10
1
LEVEL
SHIFTER
2
15
C
9
3
LEVEL
SHIFTER
5
4
ENABLE
6
LEVEL
SHIFTER
Figure 18. Function Diagram, LVXT8053
http://onsemi.com
9
X1
X0
X
Y1
Y0
Y
Z1
Z0
Z
MC74LVXT8053
ORDERING INFORMATION
Package
Shipping†
MC74LVXT8053DR2G
SOIC−16
(Pb−Free)
2500 Tape & Reel
MC74LVXT8053DTR2G
TSSOP−16
(Pb−Free)
2500 Tape & Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
10
MC74LVXT8053
PACKAGE DIMENSIONS
TSSOP−16
CASE 948F
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
S
V
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
0.25 (0.010)
8
1
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
11
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
MC74LVXT8053
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
DIM
A
B
C
D
F
G
J
K
M
P
R
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
12
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74LVXT8053/D