Axial-fan ECAC-AxiCool EN

EC/AC axial fans – AxiCool
version 2013-11
The engineer’s choice
EC/AC axial fans – AxiCool
A breath of fresh air in refrigeration technology
Maximum hygiene, optimum food safety
Setting tomorrow's standards today. This principle was key for us in deve-
The AxiCool product range has an important function to fulfil: Namely, to
loping the new AxiCool range. AxiCool represents a new market standard
keep food in cold storage fresh under hygienic conditions. That’s why
for evaporators and coolers which makes customer benefits the utmost
AxiCool is specially designed to ensure an ideal environment right from
priority. The compact fan unit also impresses with top efficiency and sim-
the start – with the emphasis on hygiene and food safety.
ple handling, whilst offering the best conditions for optimal system effi-
A high standard of refrigeration is required to maintain the quality of sto-
ciency thanks to its design features. Convenient service, ease of operation
red products – only minimal temperature fluctuations and drying-out of
and excellent air throw round off the spectrum of positive features.
the refrigerated items is permissible and the thawing cycles must be
short. All these conditions are satisfied by the ideal distribution of cold air
Top efficiency
in the cold store and innovative concepts such as the patented wall ring
The ErP Directive sets out stringent specifications to come into effect in
design. AxiCool is fully equipped to meet special challenges such as chee-
2015. So it is reassuring to know that these specifications on binding limit
se maturing processes or the storage of sensitive fruit and vegetables.
values are already surpassed by ebm-papst and that all the benefits of
this superior efficiency are there for customers to enjoy. In a nutshell:
With regard to hygiene, AxiCool cuts no corners. AxiCool features a high
AxiCool can reduce power consumption by up to 25 %. What’s more, ideal
level of splash water protection (up to IP 54) and smooth surfaces with no
system regulation guarantees highly efficient operation – even at part
visible screws. The great advantage: Dirt cannot get a grip. And the hinge-
load. And last but not least, optimised cooling and thawing cycles also
function ensures easy cleaning of the heat exchanger to HACCP specifica-
help to enhance efficiency.
tions. Simply unfasten the screws, open up the fan and perform cleaning.
Innovation meets perfection
Truly sustainable
Whichever version of the AxiCool series you decide on: You can be sure of
In our view ecology, sustainability and economical operation are insepara-
making the right choice, as the innovative features incorporated into this
ble issues. This “GreenTech” concept is embedded in the ebm-papst phil-
product range always produce perfect results. Four versions of the axial
osophy and characterises the entire life cycle: It stands for recycling,
fan are available: A standard version, a version with hinge for easier clea-
waste avoidance, ecological materials, lower emission levels, reduced
ning or with air-guiding system for ideal cold storage air distribution and a
energy consumption and hence greater efficiency. AxiCool for instance
high-end version with hinge and air-guiding system offering the full range
attains just such efficiency with a GreenTech EC motor, which operates at
of advantages.
various speed settings or with regulation by way of a linear interface. In
The fans can be supplied as size 300, 350 and 450 mm models with AC
addition, the AxiCool product range supports the concept of sustainability
or GreenTech EC motor to suit all requirements: For instance, AxiCool is
with a particularly long service life. It is often possible to preserve resour-
also available for both air flow directions. In addition,the EC technology
ces with simple means: From the outset, AxiCool was designed to have
permits control by way of two speed settings or regulation via a linear
smooth surfaces to facilitate cleaning and so save water.
interface.
The adjacent symbols highlight the winning features of the entire AxiCool
series at a glance.
2
Table of contents
EC/AC axial fans - AxiCool
2
GreenTech: The Green Company
4
Product overwiew: AxiCool
6
Overview of characteristic curves: AxiCool
7
EC axial fans - AxiCool Ø 300-450
9
AC axial fans - AxiCool Ø 300-450
27
Accessories
40
Electrical connections
42
Technical parameters & scope
46
ebm-papst representatives & subsidiaries
50
3
Sustainability is at the centre of our
thoughts and actions. Out of conviction!
Eco-friendliness and sustainability have always been at the core of our thoughts and actions. For decades, we have worked according to the
simple but strict creed of our co-founder Gerhard Sturm: “Each new product we develop has to be better than the last one in terms of economy
and ecology.” GreenTech is the ultimate expression of our corporate philosophy.
GreenTech is pro-active development.
GreenTech is eco-friendly production.
Even in the design phase, the materials and processes we use are op-
GreenTech also stands for maximum energy efficiency in our pro-
timised for the greatest possible eco-friendliness, energy balance and
duction processes. There, the intelligent use of industrial waste heat
– wherever possible – recyclability. We continually improve the materi-
and groundwater cooling, photovoltaics and, of course, our own
al and performance of our products, as well as the flow and noise cha-
cooling and ventilation technology are of the utmost importance. Our
racteristics. At the same time, we significantly reduce energy conump-
most modern plant, for instance, consumes 91% less energy than
tion. Close co-operation with universities and scientific institutes and
currently specified and required. In this way, our products contribute
the professorship we endow in the area of power engineering and re-
to protecting the environment, from their origin to their recyclable
generative energies allows us to profit from the latest research finings
packaging.
in these fields – and at the same time ensure highly qualified young
academics.
GreenTech
follows a firm
philosophy.
GreenTech is
pro-active
development.
GreenTech
pays off
for our
customers.
GreenTech is
eco-friendly
production.
GreenTech is
acknowledged
and certified.
4
GreenTech is acknowledged and certified.
Our customers profit from this every day.
Every step in our chain of production meets the stringent standards of
The heart of GreenTech is future-oriented EC technology from ebm-
environmental specialists and the public. The Deutscher Nachhaltig-
papst. The EC technology at the core of our most efficient motors
keitspreis 2012 (German Sustainability Award 2012), where we were
and fans allows efficiency of up to 90%, saves energy at a very high
given the Top3-award in the category “Germany’s most sustainable
level, significantly extends service life and makes our products
strategy for the future (company group)” bears testimony to our com-
maintenance-free. These values pay off not only for the environ-
mitment to sustainability, as does the DEKRA Award 2012 we received
ment, but every cent also pays off for the user! All ebm-papst pro-
in the category “Umwelt – Herausforderung Energiewende / Environ-
ducts – even those for which GreenTech EC technology does not
ment – Challenge: Transition to more sustainable energy systems”, to
(yet) make sense from an application viewpoint – feature the grea-
name only a few of a large number of examples. The environmental
test possible connection of economy and ecology.
advantage gained in the performance of the products developed from
our GreenTech philosophy can also be measured in the fulfillment of
the most stringent energy and environmental standards. In many instances, our products are already well below the thresholds energy
legislation will impose a few years from now – several times over.
5
Product overview: AxiCool
Overview of types:
AxiCool EC versions
Size
Motor
Standard version
Version with hinge
Version with
air-guiding system
Version with hinge
and air-guiding system
300
M3G 055-CF (2 stages)
W3G 300-JK13-30
W3G 300-TK13-30
W3G 300-UK13-30
W3G 300-WK13-30
350
M3G 074-CF (2 stages)
W3G 350-JN01-30
W3G 350-TN01-30
W3G 350-SN01-30
W3G 350-WN01-30
M3G 074-DF (2 stages)
W3G 450-JO02-30
W3G 450-TO02-30
W3G 450-SO02-30
W3G 450-WO02-30
M3G 084-FA (0-10 V)
W3G 450-JC28-30
W3G 450-TC28-30
W3G 450-SC28-30
W3G 450-WC28-30
450
Overview of types:
AxiCool AC versions
6
Size
Motor
Standard version
Version with hinge
Version with
air-guiding system
Version with hinge
and air-guiding system
300
M4E 068-CF
W4E 300-JS72-30
W4E 300-TS72-30
W4E 300-SS72-30
W4E 300-WS72-30
350
M4E 074-DF
W4E 350-JN02-30
W4E 350-TN02-30
W4E 350-SN02-30
W4E 350-WN02-30
450
M4E 074-GA
W4E 450-JP01-30
W4E 450-TP01-30
W4E 450-SP01-30
W4E 450-WP01-30
Overview of characteristic curves: AxiCool
Ø 450
Pa
Max. curves
of EC versions
120
Ø 350
100
Ø 300
80
60
40
pfs
20
qV
1000
2000
3000
4000
5000
6000
m3/h
Max. air throw
Size 300
Size 350
16 m
30 m
Size 450
40 m
In the maximum thrust range, a remaining air velocity of 0.5 m/s can still be measured.
Thrust ranges depend on the installation situation.
7
8
EC axial fans – AxiCool
9
EC axial fans – AxiCool
Ø 300, 2 Speed stages
Hz
rpm
W
A
Pa
°C
50/60
1580
83
0,8
80
-40..+40
1~ 200-240
p. 42 / H3)
Pa
in H2O
0,32
0,24
0,20
7
0,16
40
0,12
Step 1
30
2
0,08
pfs
10
0,04
6
20
0
qV
I
A
LWA
dB(A)
1
Step 2
1685
74
0,70
68
A
2
Step 2
1635
80
0,75
66
A
3
Step 2
1580
83
0,79
64
A
4
Step 2
1580
83
0,80
62
A
5
Step 1
1515
54
0,53
65
A
6
Step 1
1470
59
0,57
64
A
7
Step 1
1435
63
0,61
63
A
8
Step 1
1390
68
0,65
60
3
Step 2
50
Ped
W
A
8
A
60
n
rpm
4
0,28
80
70
200
400
500
600
1000
800
1000
1500
5
1200
2000
1
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
10
Technical features
and electr. connection
Perm. amb. temp.
VAC
(1) Nominal data in operating point with maximum load and 230 VAC
subject to alterations
Curves:
2 Speed stages
Standard
A
Max. back pressure
M3G 055-CF
Max.
current draw(1)
W3G300
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Surface thick layer passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open Rotor
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
W3G300-UK13 -30
kg
❮ "V"
Version with hinge
and air-guiding system
3,2
W3G300-WK13 -30
A
40
0,16
3
n
rpm
Ped
W
I
A
LWA
dB(A)
1
Step 2
1630
77
0,69
69
2
Step 2
1600
81
0,71
68
A
3
Step 2
1580
83
0,72
67
A
4
Step 2
1580
83
0,80
67
A
5
Step 1
1460
55
0,49
66
A
6
Step 1
1435
58
0,53
65
A
7
Step 1
1415
61
0,56
64
A
8
Step 1
1395
63
0,57
65
0,24
0,20
50
3,4
A
Step 2
8
kg
A
4
60
Mass with hinge and
air-guiding system
2,9
Mass with
air-guiding system
Mass with
hinge
Mass
Standard
❮ "V"
Version with
air-guiding system
in H2O
Pa
70
W3G300-TK13 -30
kg
0,32
80
2,7
Step 1
30
0,12
7
20
0,08
Curves:
2 Speed stages
with air-guiding
system
❮ "V"
Version with hinge
0,28
W3G300-JK13 -30
kg
10
0,04
"V"
❮ "V"
Standard version
2
6
5
pfs
Direction of air flow
– Technical features: See electrical connections p. 42
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: Variable
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 60335-1, CE
0
qV
200
400
500
600
1000
800
1000
1500
1
1200
2000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 12 f.
Electr. connection
p. 42
11
EC axial fans – AxiCool
Ø 300
W3G 300-JK13-30 (Standard version)
❮ "V"
350
305.1
65.6 40.5 ±2
5
45°
45°
Ø 39
Ø3
4
0.5
0±
7
Ø3
0.5
Mounting
dimensions:
195 ±0.5
199.5
396
380 ±0.5
94±
Ø6.5
(4x)
6
85±10
450+20
196.5
185 ±0.5
340 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 300-TK13-30 (Version with hinge)
❮ "V"
350
305.1
)
4x
5(
.
Ø6
65.6 40.5 ±2
5
45°
0.5
Ø3
.5
±0
70
12
197
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
Ø27 (2x)
450 +20
56.25 ±0.3
4
185±0.5
157±0.5
75±0.3
254 ±0.5
293.5
Ø3
9
195 ±0.5
490
°
94 ±
380 ±0.5
4x90
45°
Ø3
Mounting
dimensions:
116 ±0.3
340 ±0.5
Ø5.5 (6x)
EC axial fans – AxiCool
Ø 300
W3G 300-UK13-30 (Version with air-guiding system)
❮ "V"
107.8
5
350
305.1
40.5 ±2
45°
45°
Ø3
4
94±
7
Ø3
380 ±0.5
0.5
0.5
0±
195 ±0.5
396
Ø 39
199.5
Mounting
dimensions:
Ø6.5 (4x)
6
85±10
450+20
196.5
185 ±0.5
340 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 300-WK13-30 (Version with hinge and air-guiding system)
❮ "V"
350
305.1
40.5 ±2
x)
(4
.5
Ø6
107.8
5
45°
94 ±
0.5
Ø3
.5
±0
70
380 ±0.5
Ø3
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
Ø27 (2x)
450 +20
56.25 ±0.3
4
185±0.5
157±0.5
75±0.3
254 ±0.5
293.5
Ø3
9
195 ±0.5
490
°
4x90
45°
Mounting
dimensions:
116 ±0.3
340 ±0.5
Ø5.5 (6x)
197
13
EC axial fans – AxiCool
Ø 350, 2 Speed stages
Technical features
and electr. connection
Perm. amb. temp.
VAC
Hz
rpm
W
A
Pa
°C
50/60
1475
165
1,35
100
-40..+40
1~ 200-240
Pa
in H2O
100
Step 2
0,40
0,32
8
80
0,28
3
0,24
60
Step 1
0,20
0,16
20
0,08
30
10
0,04
40
0,12
7
50
2
6
pfs
5
0
qV
Ped
W
I
A
LWA
dB(A)
A
1
Step 2
1610
153
1,27
70
A
2
Step 2
1585
165
1,35
68
A
3
Step 2
1540
165
1,35
67
A
4
Step 2
1475
165
1,35
66
A
5
Step 1
1405
102
0,87
66
A
6
Step 1
1385
112
0,95
65
A
7
Step 1
1370
118
1,00
64
A
8
Step 1
1350
126
1,06
64
A
70
n
rpm
4
0,36
90
500
500
1000
1000
1500
1500
2000
2500
1
2000
3000
3500
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
14
p. 42 / H3)
(1) Nominal data in operating point with maximum load and 230 VAC
subject to alterations
Curves:
2 Speed stages
Standard
A
Max. back pressure
M3G 074-CF
Max.
current draw(1)
W3G350
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Surface thick layer passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open Rotor
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
0,40
90
W3G350-SN01 -30
kg
❮ "V"
Version with hinge
and air-guiding system
5,2
W3G350-WN01 -30
4
Step 2
8
40
0,16
30
0,12
50
3
Step 1
0,20
60
0,24
A
20
10
kg
5,4
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
Step 2
1560
151
1,25
72
A
2
Step 2
1545
159
1,32
71
A
3
Step 2
1520
165
1,35
71
A
4
Step 2
1475
165
1,35
72
A
5
Step 1
1380
105
0,90
69
A
6
Step 1
1365
111
0,94
68
A
7
Step 1
1350
116
0,98
68
A
8
Step 1
1345
118
1,00
69
7
2
6
5
0
qV
Mass with hinge and
air-guiding system
4,2
Mass with
air-guiding system
❮ "V"
Version with
air-guiding system
0,28
70
kg
0,32
100
80
Mass with
hinge
Mass
Standard
W3G350-TN01 -30
0,36
Pa
4,0
0,08
Curves:
2 Speed stages
with air-guiding
system
❮ "V"
Version with hinge
in H2O
W3G350-JN01 -30
kg
0,04
"V"
❮ "V"
Standard version
pfs
Direction of air flow
– Technical features: See electrical connections p. 42
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: Variable
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 60335-1, CE
500
500
1000
1000
1500
1500
2000
2500
3000
1
2000
3500
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 16 f.
Electr. connection
p. 42
15
EC axial fans – AxiCool
Ø 350
W3G 350-JN01-30 (Standard version)
❮ "V"
76
6.5
417
352.5
65.7
50.5 ±2
45°
45°
Ø4
1
0.5
5±
3
Ø4
0.5
446 ±0.5
61±
233
Mounting
dimensions:
228.5 ±0.5
463
Ø 46
Ø6.5
(4x)
6
85±10
450 +20
196.5
185 ±0.5
409.5 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 350-TN01-30 (Version with hinge)
❮ "V"
65.7
417
352.5
50.5 ±2
x)
(4
.5
Ø6
76
6.5
45°
0.5
Ø4
.5
±0
35
446 ±0.5
61±
228.5 ±0.5
Ø27 (2x)
56.25 ±0.3
1
185±0.5
157±0.5
75±0.3
16
197
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
450 +20
327
Ø4
6
287.5 ±0.5
557
°
4x90
45°
Ø4
Mounting
dimensions:
116 ±0.3
409.5 ±0.5
Ø5.5 (6x)
EC axial fans – AxiCool
Ø 350
W3G 350-SN01-30 (Version with air-guiding system)
❮ "V"
417
352.5
65.7
119
6.5
50.5 ±2
45°
45°
Ø4
1
61±
3
Ø4
446 ±0.5
0.5
0.5
5±
228.5 ±0.5
463
Ø 46
233
Mounting
dimensions:
Ø6.5 (4x)
450+20
6
85±10
196.5
185 ±0.5
409.5 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 350-WN01-30 (Version with hinge and air-guiding system)
❮ "V"
65.7
417
352.5
50.5 ±2
x)
(4
.5
Ø6
119
6.5
45°
0.5
Ø4
.5
±0
35
446 ±0.5
61±
228.5 ±0.5
Ø27 (2x)
56.25 ±0.3
1
185±0.5
157±0.5
75±0.3
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
450 +20
327
Ø4
6
287.5 ±0.5
557
°
4x90
45°
Ø4
Mounting
dimensions:
116 ±0.3
409.5 ±0.5
Ø5.5 (6x)
197
17
EC axial fans – AxiCool
Ø 450, 2 Speed stages
Hz
rpm
W
A
Pa
°C
50/60
980
163
1,34
74
1~ 200-240
A
-40..+40
p. 42 / H3)
Pa
in H2O
0,28
70
3
30
0,12
20
0,08
10
0,04
0,16
Step 1
40
Ped
W
I
A
LWA
dB(A)
7
pfs
2
6
0
qV
400
800
1000
1200
2000
1600
3000
A
1
Step 2
1105
163
1,34
69
A
2
Step 2
1055
163
1,34
67
A
3
Step 2
1015
163
1,34
63
A
4
Step 2
980
163
1,34
68
A
5
Step 1
955
104
0,89
65
A
6
Step 1
935
114
0,97
63
A
7
Step 1
920
121
1,03
61
A
8
Step 1
895
129
1,09
67
Step 2
A
0,20
50
0,24
8
60
n
rpm
0,32
80
4
2000
2400
4000
5
2800
5000
1
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
18
Technical features
and electr. connection
Perm. amb. temp.
VAC
(1) Nominal data in operating point with maximum load and 230 VAC
subject to alterations
Curves:
2 Speed stages
Standard
Max. back pressure
M3G 074-DF
Max.
current draw(1)
W3G450
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Surface thick layer passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open Rotor
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
5,7
W3G450-SO02 -30
kg
❮ "V"
Version with hinge
and air-guiding system
8,6
W3G450-WO02 -30
50
0,24
8
3
30
0,12
0,16
Step 1
40
kg
8,8
n
rpm
Ped
W
I
A
LWA
dB(A)
20
10
A
1
Step 2
1090
163
1,34
70
A
2
Step 2
1045
163
1,34
69
A
3
Step 2
1000
163
1,34
66
A
4
Step 2
980
163
1,34
68
A
5
Step 1
935
104
0,89
66
A
6
Step 1
920
112
0,96
65
A
7
Step 1
905
120
1,02
63
A
8
Step 1
890
127
1,07
65
Step 2
A
0,20
60
0,28
4
70
Mass with hinge and
air-guiding system
❮ "V"
Version with
air-guiding system
Mass with
air-guiding system
Mass with
hinge
Mass
Standard
W3G450-TO02 -30
kg
in H2O
Pa
80
5,5
0,08
Curves:
2 Speed stages
with air-guiding
system
❮ "V"
Version with hinge
0,32
W3G450-JO02 -30
kg
0,04
"V"
❮ "V"
Standard version
7
2
6
5
pfs
Direction of air flow
– Technical features: See electrical connections p. 42
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
On account of the installation conditions, ferritic damping in the
connection line may be required for the application.
– Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: Variable
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 60335-1, CE
0
qV
400
800
1000
1200
2000
1600
3000
2000
2400
4000
1
2800
5000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 22 f.
Electr. connection
p. 42
19
EC axial fans – AxiCool
Ø 450, Speed-controlled
Hz
rpm
W
A
Pa
°C
50/60
1300
345
2,2
125
-25..+40
1~ 200-277
p. 43 / K1)
Pa
in H2O
n
rpm
Ped
W
I
A
LWA
dB(A)
0,48
4
120
100
0,40
A
80
0,32
60
0,24
3
40
0,16
20
0,08
2
pfs
1
0
qV
1000
1000
1500
2000
2000
3000
2500
4000
3000
5000
3500
6000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
20
Technical features
and electr. connection
Perm. amb. temp.
VAC
(1) Nominal data in operating point with maximum load and 230 VAC
subject to alterations
Curves:
Speed-controlled
Standard
A
Max. back pressure
M3G 084-FA
Max.
current draw(1)
W3G450
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal
voltage range
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Surface thick layer passivated
Electronics enclosure: Die-cast aluminium
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: Rotor-side
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
A
1
1315
265
1,77
70
A
2
1310
300
1,99
68
A
3
1310
323
2,13
67
A
4
1300
345
2,20
69
120
❮ "V"
Version with
air-guiding system
7,7
W3G450-SC28 -30
❮ "V"
Version with hinge
and air-guiding system
kg
10,6
0,40
80
60
0,24
100
0,32
A
40
20
kg
10,8
W3G450-WC28 -30
4
Mass with hinge and
air-guiding system
kg
Mass with
air-guiding system
Mass with
hinge
Mass
Standard
Pa
W3G450-TC28 -30
in H2O
7,5
0,16
Curves:
Speed-controlled
with air-guiding
system
❮ "V"
Version with hinge
0,48
W3G450-JC28 -30
kg
0,08
"V"
❮ "V"
Standard version
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1300
267
1,77
73
A
2
1300
296
1,96
71
A
3
1300
322
2,12
71
A
4
1300
345
2,20
72
3
2
1
pfs
Direction of air flow
– Technical features: See electrical connections p. 43
– EMC: Interference emission acc. to EN 61000-6-3
Interference immunity acc. to EN 61000-6-2
Harmonics acc. to EN 61000-3-2/3
– Touch current: < 3,5 mA acc. to IEC 60990 (test circuit, illustration 4)
– Cable exit: Variable
– Protection class: I (if customer has provided connection for protective earth)
– Product conforming to standards: EN 60335-1, CE
0
qV
1000
1000
1500
2000
2000
3000
2500
4000
3000
5000
3500
6000
cfm
m3/h
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 24 f.
Electr. connection
p. 43
21
EC axial fans – AxiCool
Ø 450
W3G 450-JO02-30 (Standard version)
❮ "V"
548
445.1
97.6 70.5 ±2
9
45°
45°
Ø5
2
0.5
0±
92±
7
Ø5
580 ±0.5
0.5
Mounting
dimensions:
298.5
450 +20
6
85±10
Ø6.5 (4x)
295 ±0.5
594
Ø 59
376.5
368 ±0.5
540 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 450-TO02-30 (Version with hinge)
❮ "V"
548
445.1
.5
Ø6
97.6 70.5±2
9
x)
(4
92 ±
Ø5
.5
±0
70
0.5
22
56.25 ±0.3
30 ±0.2
377
6
85 ±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
450+20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
EC axial fans – AxiCool
Ø 450
W3G 450-SO02-30 (Version with air-guiding system)
❮ "V"
161
9
548
445.1
70.5 ±2
45°
45°
Ø 59
Ø5
2
92±
7
Ø5
295 ±0.5
594
580 ±0.5
0.5
0.5
0±
298.5
Mounting
dimensions:
Ø6.5 (4x)
450+20
6
85±10
376.5
368 ±0.5
540 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W3G 450-WO02-30 (Version with hinge and air-guiding system)
❮ "V"
548
445.1
70.5±2
.5
Ø6
161
9
x)
(4
92 ±
Ø5
.5
±0
70
0.5
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
Connection line PVC 4G 0.5 mm ,
4 x brass lead tips crimped
377
56.25 ±0.3
30 ±0.2
2
6
85 ±10
450+20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
23
EC axial fans – AxiCool
Ø 450
W3G 450-JC28-30 (Standard version)
❮ "V"
548
445.1
113.5 70.5 ±2
9
45°
45°
Ø 59
Ø5
2
0±
7
Ø5
0.5
0.5
Mounting
dimensions:
298.5
450+20
6
85±10
Ø6.5 (4x)
295 ±0.5
594
580 ±0.5
92±
376.5
368 ±0.5
540 ±0.5
Connection line PVC 3G AWG 20,
3 x brass lead tips crimped
Connection line PVC 5X AWG 22,
5 x brass lead tips crimped
W3G 450-TC28-30 (Version with hinge)
❮ "V"
548
445.1
.5
Ø6
113.5 70.5±2
9
x)
(4
92 ±
Ø5
.5
±0
70
0.5
Connection line PVC 3G AWG 20,
3 x brass lead tips crimped
24
56.25 ±0.3
30 ±0.2
377
6
85 ±10
Connection line PVC 5X AWG 22,
5 x brass lead tips crimped
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
450+20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
EC axial fans – AxiCool
Ø 450
W3G 450-SC28-30 (Version with air-guiding system)
❮ "V"
161
9
548
445.1
70.5 ±2
45°
45°
Ø 59
Ø5
2
92±
7
Ø5
295 ±0.5
594
580 ±0.5
0.5
0.5
0±
298.5
Mounting
dimensions:
Ø6.5 (4x)
450+20
6
85±10
376.5
368 ±0.5
540 ±0.5
Connection line PVC 3G AWG 20,
3 x brass lead tips crimped
Connection line PVC 5X AWG 22,
5 x brass lead tips crimped
W3G 450-WC28-30 (Version with hinge and air-guiding system)
❮ "V"
548
445.1
70.5±2
.5
Ø6
161
9
x)
(4
92 ±
Ø5
.5
±0
70
0.5
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
Connection line PVC 3G AWG 20,
3 x brass lead tips crimped
377
56.25 ±0.3
30 ±0.2
Connection line PVC 5X AWG 22,
5 x brass lead tips crimped
6
85 ±10
450+20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
25
26
AC axial fans – AxiCool
27
AC axial fans – AxiCool
Ø 300
VAC
Hz
rpm
W
A
μF/VDB
Pa
°C
1~230
1~230
50
60
1320
1500
72
90
0,32
0,40
2,0/400
2,0/400
50
60
-40..+50
-40..+50
p. 44 / A1)
(1) Nominal data in operating point with maximum load and 230 VAC
4
Pa
0,12
0,20
30
20
0,08
40
10
0,04
50
A
4
3
3
2
2
pfs
1
0
qV
200
200
400
400
600
600
800
1000
800
1200
1400
1000
1600
1800
50 Hz
1
1200 cfm
2000
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1370
62
0,29
61
A
2
1350
65
0,30
60
A
3
1325
69
0,31
59
A
4
1320
72
0,32
59
B
1
1570
78
0,34
65
B
2
1535
83
0,36
64
B
3
1500
87
0,38
62
B
4
1500
90
0,40
61
B
0,16
60
0,24
Curves:
Standard
in H2O
subject to alterations
28
Electr. connection
Perm. amb. temp.
B
Max. back pressure
A
Capacitor
M4E 068-CF
Max.
current draw(1)
W4E 300
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
4,7
W4E 300-SS72 -30
30
0,12
20
5,0
W4E 300-WS72 -30
B
kg
5,2
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1355
65
0,29
63
A
2
1345
66
0,30
62
A
3
1330
68
0,31
62
A
4
1320
72
0,32
64
B
1
1530
84
0,36
66
B
2
1515
85
0,37
65
B
3
1500
87
0,38
65
B
4
1500
90
0,40
65
4
3
3
2
2
10
❮ "V"
Version with hinge
and air-guiding system
A
0,16
4
40
kg
Mass with hinge and
air-guiding system
❮ "V"
Version with
air-guiding system
Mass with
air-guiding system
Mass with
hinge
Mass
Standard
50
W4E 300-TS72 -30
kg
in H2O
Pa
60
4,5
0,08
Curves:
with air-guiding
system
❮ "V"
Version with hinge
0,24
W4E 300-JS72 -30
kg
0,20
❮ "V"
Standard version
0,04
"V"
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE
1
pfs
Direction of air flow
–
–
–
–
–
–
0
qV
200
200
400
400
600
600
800
1000
800
1200
1400
1
1200 cfm
1000
1600
1800
2000
50 Hz
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 30 f.
Capacitors
p. 40 f.
Electr. connection
p. 44
29
AC axial fans – AxiCool
Ø 300
W4E 300-JS72-30 (Standard version)
❮ "V"
350
305.1
65.4 42.4 ±2
5
45°
45°
Ø 39
Ø3
4
0.5
0±
7
Ø3
0.5
199.5
Mounting
dimensions:
195 ±0.5
396
380 ±0.5
94±
Ø6.5
(4x)
6
85±10
450 +20
196.5
185 ±0.5
340 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 300-TS72-30 (Version with hinge)
❮ "V"
350
305.1
x)
(4
.5
Ø6
65.4 42.4 ±2
5
45°
0.5
Ø3
.5
±0
70
380 ±0.5
94 ±
30
197
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
Ø27 (2x)
450 +20
56.25 ±0.3
4
185±0.5
157±0.5
75±0.3
254 ±0.5
293.5
Ø3
9
195 ±0.5
490
°
4x90
45°
Ø3
Mounting
dimensions:
116 ±0.3
340 ±0.5
Ø5.5 (6x)
AC axial fans – AxiCool
Ø 300
W4E 300-SS72-30 (Version with air-guiding system)
❮ "V"
107.5
5
350
305.1
42.4 ±2
45°
45°
Ø 39
Ø3
4
94±
Ø3
.5
±0
70
195 ±0.5
396
380 ±0.5
0.5
199,5
Mounting
dimensions:
Ø6.5 (4x)
6
85±10
450+20
196.5
185 ±0.5
340 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 300-WS72-30 (Version with hinge and air-guiding system)
❮ "V"
350
305.1
42.4 ±2
x)
(4
.5
Ø6
107.5
5
45°
94 ±
0.5
Ø3
±0
70
.5
380 ±0.5
Ø3
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
Ø27 (2x)
450 +20
56.25 ±0.3
4
185±0.5
157±0.5
75±0.3
254 ±0.5
293.5
Ø3
9
195 ±0.5
490
°
4x90
45°
Mounting
dimensions:
116 ±0.3
340 ±0.5
Ø5.5 (6x)
197
31
AC axial fans – AxiCool
Ø 350
Perm. amb. temp.
VAC
Hz
rpm
W
A
μF/VDB
Pa
°C
1~230
50
1340
165
0,73
4,0/400
80
-40..+45
p. 44 / A1)
(1) Nominal data in operating point with maximum load and 230 VAC
0,16
20
0,08
30
10
0,04
40
0,12
50
0,32
Pa
60
0,28
70
A
3
2
pfs
1
0
qV
n
rpm
Ped
W
I
A
LWA
dB(A)
4
0,24
80
0,20
Curves:
Standard
in H2O
subject to alterations
200
400
500
600
1000
800
1500
1000
1200
2000
1400
2500
1600
1800
3000
50 Hz
cfm
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
32
Electr. connection
Max. back pressure
A
Capacitor
M4E 074-DF
Max.
current draw(1)
W4E 350
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring, air-guiding system and blades: Plastic PP
Rotor: Coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: "B"
– Mounting position: Shaft horizontal or rotor on bottom; rotor on top on request
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
A
1
1400
127
0,57
67
A
2
1385
137
0,61
66
A
3
1365
146
0,64
63
A
4
1340
165
0,73
63
❮ "V"
Version with
air-guiding system
5,5
W4E 350-SN02 -30
kg
❮ "V"
Version with hinge
and air-guiding system
6,2
W4E 350-WN02 -30
kg
6,4
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1375
138
0,61
71
A
2
1365
144
0,63
70
A
3
1355
149
0,65
69
A
4
1340
165
0,73
70
0,24
40
0,16
50
30
0,12
60
0,20
0,28
4
70
Mass with hinge and
air-guiding system
kg
Mass with
air-guiding system
W4E 350-TN02 -30
Mass with
hinge
Mass
Standard
Pa
80
5,3
A
3
2
20
0,08
Curves:
with air-guiding
system
❮ "V"
Version with hinge
in H2O
W4E 350-JN02 -30
kg
0,32
❮ "V"
Standard version
10
0,04
"V"
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE
1
pfs
Direction of air flow
–
–
–
–
–
–
0
qV
200
400
500
600
1000
800
1500
1000
1200
2000
1400
2500
1600
1800
3000
50 Hz
cfm
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 34 f.
Capacitors
p. 40 f.
Electr. connection
p. 44
33
AC axial fans – AxiCool
Ø 350
W4E 350-JN02-30 (Standard version)
❮ "V"
76
6.5
417
352.5
59.8
50.5 ±2
45°
45°
Ø4
1
0.5
5±
3
Ø4
0.5
446 ±0.5
61±
233
Mounting
dimensions:
228.5 ±0.5
463
Ø 46
Ø6.5
(4x)
6
85±10
450+20
196.5
185 ±0.5
409.5 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 350-TN02-30 (Version with hinge)
❮ "V"
59.8
50.5 ±2
417
352.5
)
4x
5(
.
Ø6
76
6.5
45°
0.5
Ø4
.5
±0
35
446 ±0.5
61±
228.5 ±0.5
Ø27 (2x)
56.25 ±0.3
1
185±0.5
157±0.5
75±0.3
34
197
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
450 +20
327
Ø4
6
287.5 ±0.5
557
°
4x90
45°
Ø4
Mounting
dimensions:
116 ±0.3
409.5 ±0.5
Ø5.5 (6x)
AC axial fans – AxiCool
Ø 350
W4E 350-SN02-30 (Version with air-guiding system)
❮ "V"
417
352.5
59.8
119
6.5
50.5 ±2
45°
45°
Ø4
1
61±
3
Ø4
446 ±0.5
0.5
0.5
5±
233
Mounting
dimensions:
228.5 ±0.5
463
Ø 46
Ø6.5 (4x)
6
85±10
450 +20
196.5
185 ±0.5
409.5 ±0.5
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 350-WN02-30 (Version with hinge and air-guiding system)
❮ "V"
59.8
50.5 ±2
417
352.5
x)
(4
.5
Ø6
119
6.5
45°
61±
0.5
Ø4
.5
±0
35
446 ±0.5
Ø4
228.5 ±0.5
Ø27 (2x)
56.25 ±0.3
1
185±0.5
157±0.5
75±0.3
30 ±0.2
85±10
Connection line PVC 4G 0.5 mm2,
4 x brass lead tips crimped
6
450 +20
327
Ø4
6
287.5 ±0.5
557
°
4x90
45°
Mounting
dimensions:
116 ±0.3
409.5 ±0.5
Ø5.5 (6x)
197
35
AC axial fans – AxiCool
Ø 450
Max. back pressure
Perm. amb. temp.
A
Capacitor
M4E 074-GA
Max.
current draw(1)
W4E 450
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
Nominal voltage
Curve
– Material: Guard grille / support bracket: Steel, phosphated and coated in black (RAL 9005)
Wall ring and air-guiding system: Plastic PP
Blades: Sheet steel, coated in Black
Rotor: Coated in black
– Number of blades: 5
– Direction of rotation: Counter-clockwise, seen on rotor
– Type of protection: IP 44, depending on installation and position (acc. to EN 60034-5)
– Insulation class: "F"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Continuous operation (S1)
– Bearings: Maintenance-free ball bearings with low-temperature grease
VAC
Hz
rpm
W
A
μF/VDB
Pa
°C
1~230
50
1340
300
1,32
8,0/400
70
-40..+40
(1) Nominal data in operating point with maximum load and 230 VAC
Pa
70
0,28
Curves:
Standard
in H2O
subject to alterations
0,24
40
0,16
30
0,12
50
0,20
60
3
0,08
10
0,04
2
20
pfs
1
0
qV
n
rpm
Ped
W
I
A
LWA
dB(A)
4
A
1000
1000
1500
2000
2000
3000
2500
4000
3000
5000
50 Hz
cfm
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
36
p. 44 / A1)
A
1
1400
245
1,10
76
A
2
1380
260
1,17
73
A
3
1365
278
1,24
72
A
4
1340
300
1,32
71
❮ "V"
Version with
air-guiding system
9,7
W4E 450-SP01 -30
❮ "V"
Version with hinge
and air-guiding system
kg
10,8
W4E 450-WP01 -30
4
40
0,16
30
0,12
50
0,20
60
0,24
A
10
kg
11,0
n
rpm
Ped
W
I
A
LWA
dB(A)
A
1
1400
245
1,10
75
A
2
1360
267
1,20
74
A
3
1345
284
1,26
73
A
4
1340
300
1,32
72
3
2
20
Mass with hinge and
air-guiding system
kg
Mass with
air-guiding system
W4E 450-TP01 -30
Mass with
hinge
Mass
Standard
Pa
70
9,5
0,08
Curves:
with air-guiding
system
❮ "V"
Version with hinge
in H2O
W4E 450-JP01 -30
kg
0,28
❮ "V"
Standard version
0,04
"V"
Motor protection: TOP wired internally
Touch current: < 0,75 mA acc. to IEC 60990 (test circuit, illustration 4)
Cable exit: Variable
Protection class: I (if customer has provided connection for protective earth)
Product conforming to standards: EN 60335-1, CE
Approvals: VDE
B
1
pfs
Direction of air flow
–
–
–
–
–
–
0
qV
1000
1000
1500
2000
2000
3000
2500
4000
3000
5000
50 Hz
cfm
m3/h
60 Hz
Air performance measured as per: ISO 5801, Installation category A, in ebm-papst full nozzle and without protection against
accidental contact. Suction-side noise levels: LWA as per ISO 13347, LpA measured at 1 m distance to fan axis. The acoustic
values given are only valid under the measurment conditions listed and may vary depending on the installation situation. With
any deviation to the standard setup, the specific values have to be checked and reviewed once installed or fitted! For detailed
information see page 46 ff.
Drawings
p. 38 f.
Capacitors
p. 40 f.
Electr. connection
p. 44
37
AC axial fans – AxiCool
Ø 450
W4E 450-JP01-30 (Standard version)
❮ "V"
548
445.1
97.6 70.5±2
9
45°
45°
Ø5
2
0.5
0±
7
Ø5
0.5
580 ±0.5
92±
Mounting
dimensions:
298.5
450+20
6
85±10
Ø6.5 (4x)
295 ±0.5
594
Ø 59
376.5
368 ±0.5
540 ±0.5
Connection line Silikon 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 450-TP01-30 (Version with hinge)
❮ "V"
548
445.1
.5
Ø6
97.6 70.5±2
9
x)
(4
92 ±
.5
±0
70
Ø5
0.5
38
377
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
56.25 ±0.3
30 ±0.2
Connection line Silikon 4G 0.5 mm2,
4 x brass lead tips crimped
6
85 ±10
450 +20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
AC axial fans – AxiCool
Ø 450
W4E 450-SP01-30 (Version with air-guiding system)
❮ "V"
161
9
548
445.1
70.5±2
45°
45°
Ø 59
Ø5
2
92±
7
Ø5
295 ±0.5
594
580 ±0.5
0.5
0.5
0±
298.5
Mounting
dimensions:
Ø6.5 (4x)
450+20
6
85±10
376.5
368 ±0.5
540 ±0.5
Connection line Silikon 4G 0.5 mm2,
4 x brass lead tips crimped
W4E 450-WP01-30 (Version with hinge and air-guiding system)
❮ "V"
548
445.1
70.5±2
.5
Ø6
161
9
x
(4
)
92 ±
Ø5
.5
±0
70
0.5
377
295 ±0.5
326.75 ±0.5
Ø27 (4x)
368 ±0.5
157±0.5
75±0.3
56.25 ±0.3
30 ±0.2
Connection line Silikon 4G 0.5 mm2,
4 x brass lead tips crimped
6
85 ±10
450 +20
392.5
353 ±0.5
688
0°
4x9
45°
Ø5
Mounting
dimensions:
580 ±0.5
45°
Ø5.5 (12x)
116 ±0.3
255 ±0.5
296 ±0.5
337±0.5
540 ±0.5
39
Capacitors
b
c ±10
7 ±1
Øa
M8
10
MKP motor capacitors P0 (without fuse)
Part no.
Capacity
a
b (max.)
c
99283-4-7320
2,0 μF
25-28
58,0
235,0
99284-4-7320
4,0 μF
28-32
58,0
235,0
99286-4-7320
8,0 μF
35-40
72,0
235,0
subject to alterations
40
– Material: Housing made of thermoplastic
resin
– Connection line: Multi-lead
PVC cable 0.5 mm2 with brass lead tips
– Approval: VDE according to DIN EN 60252
(VDE 0560/8)
– Calculated life time:
400 V; -25 to +85°C; 30,000 hrs; class A
450 V; -25 to +85°C; 10,000 hrs; class B
Capacitors
c
– Material: Plastic cap, aluminium cup
– Designation: FPU or P2 according to
IEC 252 (non-flammable, non-explosive,
circuit-breaking)
– Approval: VDE according to DIN EN 60252
(VDE 0560/8)
– Calculated life time:
420 V; -25 to +85°C; 30,000 hrs; class A
470 V; -25 to +85°C; 10,000 hrs; class B
500 V; -25 to +85°C; 3,000 hrs; class C
b
Øa
M8
Ø a + 3,5
10
7 ±1
35 +5
235 +10
-5
MKP motor capacitors FPU or P2 (with fuse)
Part no.
Capacity
a
b (max.) c (max.)
02156-4-7320
2,0 μF
25,0
77,0
92,0
02161-4-7320
4,0 μF
25-30
104,0
135,0
02165-4-7320
8,0 μF
30-35
102,0
111,0
max. 9 mm
subject to alterations
– Pull-off protector: The housing expands
by max. 9 mm. The protector responds to
overload by the generated excess pressure
snapping off the internal lead in a predetermined breaking point.
– Mounting: c is the overall dimension of the
capacitor which has to be taken into account
when mounting the part. The capacitor design, however, depends on the manufacturer.
The expansion (9 mm) is either added to dimension b, or it is already integrated in the
capacitor.
41
Electrical connections EC
H3)
Technical features (M3G 055 / M3G 074 with 2 Speed stages):
• Speed adjustment input (230V)
• Over-temperature protected electronics / motor
• Motor current limitation
• Locked-rotor protection
• Soft start
Customer circuit
Connection
Fan
L
AC1
P
N
AC2
N
L
N
SL
SL
PE
L
N
SL
SL
Connection
Colour
Assignment / function
L
black
Power supply 230 VAC, 50 - 60 Hz
N
blue
Neutral conductor
PE
green/yellow
Protective earth
SL
brown
Speed selection: switch open = step 1; switch closed = step 2
42
PE
PE1
Electrical connections EC
K1)
Technical features:
• PFC (passive)
• Control input 0-10 VDC / PWM
• Output 10 VDC max. 1,1 mA
• Over-temperature protected electronics / motor
• Line undervoltage detection
• Motor current limitation
• Soft start
• Control interface with SELV potential safely disconnected from the mains
Notes on various control possibilities and their applications
Umin = 15 V
Imax =
10 mA
Mains
50/60 Hz
L
black
N
blue
+
-
PE
green/yellow
NC
not used
+
Alarm relay:
Break for failure
COM
not used
U
PWM
Voltage output
red
+10 V
max. 1.1 mA
-
10 K
12 V
Lin/PWM control input
yellow
0-10 VDC /
PWM
1 μF
GND
blue
Speed setting
PWM 1 - 10 kHz
Speed setting
with variable
resistance
Full speed
Speed setting
1 V - 10 V
10 V -> n=max
approx. 1 V -> n=min
< 1 V -> n=0
100% PWM -> n=max
approx. 10% PWM -> n=min
< 10% PWM -> n=0
start up at > 1.4 V
start up at > 14 %
Customer circuit
Connection
N
PE
+10 V
0-10 V
PWM
GND
Line 2
L
Line 1
Fan
black
blue
green/yellow
red
yellow
blue
Line
Connection
Colour Assignment / function
Line
Connection
Colour Assignment / function
1
L
black
Mains 50/60 Hz, phase
2
+10 V
red
Voltage output +10 V max. 1.1 mA
N
blue
Mains 50/60 Hz, neutral
0-10 V / PWM
yellow
Control input (Impedance 100 kΩ)
PE
green/yel
Protective earth
GND
blue
GND
43
Electrical connections AC
A1)
A1) Single-phase capacitor motor (1~ 230 VAC power line)
with TOP wired internally
PE
L
N
C
U1
TOP
44
U2 Z
U1 = blue
U2 = black
Z = brown
= green/yellow
45
Technical parameters & scope
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best possible product for your application.
Careful monitoring of the market ensures that technical innovations are reflected in the improvements of our products. Based on the technical parameters listed below and the ambience you want our product to operate in, we here at ebm-papst can always work out the best solution for your specific
application..
General performance parameters
The majority of our products use maintenance-free ball bearings for
Any deviations from the technical data and parameters described here
any mounting position possible.
are listed on the product-specific data sheet.
The service life L10 of the ball bearings can be taken as approx. 40,000
Type of protection
The type of protection is specified in the product-specific data sheets.
Insulation class
The insulation class is specified in the product-specific data sheets.
operating hours at an ambient temperature of 40 °C, yet this estimate
can vary according to the actual ambient conditions.
We will gladly provide you with a lifetime calculation taking into account
your specific operating conditions.
Motor protection / thermal protection
Mounting position
Information on motor protection and thermal protection is provided in the
The mounting position is specified in the product-specific data sheets.
product-specific data sheets.
Depending on motor type and field of application, the following protective
Condensate discharge holes
features are realised:
Information on the condensate discharge holes is provided in the
– Thermal overload protection (TOP), either in-circuit or external
product-specific data sheets.
– PTC with electronic diagnostics
Mode of operation
– Impedance protection
The mode of operation is specified in the product-specific data sheets.
– Thermal overload protection (TOP) with electronic diagnostics
– Current limitation via electronics
Protection class
The protection class is specified in the product-specific data sheets.
Service life
The service life of ebm-papst products depends on two major factors:
If an external TOP is connected, the customer has to make sure to
connect a conventional trigger device for switching it off.
Products without fitted TOP and without protection against improper use,
a motor protection complying with the valid standards has to be installed.
– The service life of the insulation system
Mechanical strain / performance parameters
– The service life of the bearing system
All ebm-papst products are subjected to comprehensive tests complying
The service life of the insulation system mainly depends on voltage level,
with the normative specifications. In addition to this, the tests also reflect
temperature and ambient conditions, such as humidity and condensation.
the vast experience and expertise of ebm-papst.
The service life of the bearing system depends mainly on the thermal load
on the bearing.
46
Vibration test
Standards
Vibration tests are carried out in compliance with
Information on standards is provided in the product-specific data sheets.
– Vibration test in operation according to DIN IEC 68, parts 2-6
– Vibration test at standstill according to DIN IEC 68, parts 2-6
EMC
Information on EMC standards is provided in the product-specific data
Shock load
sheets.
Shock load tests are carried out in compliance with
Complying with the EMC standards has to be established on the final
– Shock load according to DIN IEC 68, parts 2-27
appliance, as different mounting situations can result in changed EMC
Balancing quality
properties.
Testing the balancing quality is carried out in compliance with
Leakage current
– Residual imbalance according to DIN ISO 1940
Information on the leakage current is provided in the product-specific
– Standard balancing quality level G 6.3
data sheets.
Should you require a higher balancing quality level for your specific
Measuring is according to IEC 60990.
application, please let us know and specify this when ordering your
product.
Approvals
In case you require a specific approval for your ebm-papst product
Chemo-physical strain / performance parameters
(VDE, UL, GOST, CCC, CSA, etc.) please let us know.
Should you have questions about chemo-physical strain, please direct
Most of our products can be supplied with the relevant approval.
them to your ebm-papst contact.
Information on existing approvals is provided in the product-specific
Fields of application, industries and applications
data sheets.
Our products are used in various industries and applications:
Air performance measurements
Ventilation, air-conditioning and refrigeration technology, clean room
All air performance measurements are carried out on suction side and on
technology, automotive and rail technology, medical and laboratory tech-
chamber test beds conforming to the specifications as per ISO 5801 and
nology, electronics, computer and office technology, telecommunications,
DIN 24163. The fans under test are installed in the measuring chamber at
household appliances, heating, machines and plants, drive engineering.
free air intake and exhaust (installation category A) and are operated at
Our products are not designed for use in the aviation and aerospace
nominal voltage, with AC also at nominal frequency, and without any
industry!
additional components such as guard grilles.
Legal and normative directives
The products described in this catalogue are designed, developed and
As required by the standard, the air performance curves correspond to
an air density of 1.2 kg/m3.
produced in keeping with the standards in place for the relevant product
and, if known, the conditions governing the relevant fields of application.
47
Technical parameters & scope
Measurement conditions for air and noise measurement
Sound pressure level and sound level
ebm-papst products are measured under the following conditions:
All acoustic values are established according to ISO 13347, DIN 45635
– Axial and diagonal fans in direction of rotation “V” in full nozzle and
and ISO 3744/3745 to accuracy class 2 and given in A-rated form.
without guard grille
When the sound pressure level (Lp) is measured, the microphone is on
– Backward curved centrifugal fans, free-running and with inlet nozzle
the intake side of the fan being tested, usually at a distance of 1 m on
– Forward curved single and dual inlet centrifugal fans with housing
the fan axis.
Noise measurements
All noise measurements are carried out in low-reflective test rooms with
reverberant floor. Thus the ebm-papst acoustic test chambers meet the
requirements of precision class 1 according to DIN EN ISO 3745. For noise
measurement, the fans being tested are placed in a reverberant wall and
operated at nominal voltage (for AC, also at nominal frequency) without
additional attachments such as the guard grille.
To measure the sound power level (Lw), 10 microphones are distributed
over an enveloping surface on the intake side of the fan being tested
(see graphic). The sound power level measured can be roughly calculated
from the sound pressure level by adding 7 dB.
Measuring configuration as per ISO 13347-3 respectively DIN 45635-38:
10 measuring points
d≥D
h = 1,5d ... 4,5d
D
1,5d
Measurement area S = 6d2 + 7d (h + 1,5d)
h
3d
2d
48
9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A).
15
10
9
Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound pressure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is
5
the noise values specified in the data sheet. This is shown in the diagram opposite.
0
The noise characteristics of multiple identical fans can be determined in advance based on
[dB]
[dB(A)]
Adding 2 noise sources with the same level results in a level increase of approx. 3 dB.
Increase in sound pressure / sound power level
Combined level of multiple same-level sound sources
1
2
3
4
5
6 7 8 9 10
15
20 25
point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is 4 dB.
The level increase can now be read in the diagram as approx. 1.5 dB. This means that the
overall sound level of the unit can be expected to be 76.5 dB(A).
3
2
1,5
Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the operating
1
levels given in the data sheet. This is shown in the diagram opposite.
0
The acoustic performance of two different fans can be predetermined based on the sound
Increase in sound pressure / sound power level
Combined level of two different-level sound sources
[dB]
[dB(A)]
Number of sources of sound with identical level
0
4
8
12
16
20
Sound power level is independent of distance to the sound source. In contrast to this, sound
-10
pressure level decreases the further away the noise source is. The adjacent diagram shows the
0
[dB]
[dB(A)]
Distance laws
24
[dB]
[dB(A)]
Difference in level with two sources of sound
decrease in level under far sound field conditions. Far sound field conditions apply whenever the
In the near field of the fan, other correlations apply and the decrease in levels can be considerably smaller. The following example only applies to far sound field conditions and can vary
strongly depending on the installation effects:
With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of
1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by
-20
-26
-30
this complex topic. Per doubling of distance, the level in the far sound field decreases by 6 dB.
-40
be considered. For more information on far sound field, please consult the relevant literature on
Decrease in sound pressure level
distance between microphone and fan is big when compared to fan diameter and wavelength to
1
Distance
2
5
10
20
50
100
[m]
26 dB, i.e. a sound pressure level of 39 dB(A).
49
ebm-papst in Germany
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
GERMANY
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
50
ebm-papst St. Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
78112 St. Georgen
GERMANY
Phone +49 7724 81-0
Fax +49 7724 81-1309
[email protected]
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
16341 Panketal
GERMANY
Phone +49 30 944149-62
Fax +49 30 944149-63
[email protected]
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
74199 Unterheinriet
GERMANY
Phone +49 7130 404569-1
Fax +49 7130 404569-2
[email protected]
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
33739 Bielefeld
GERMANY
Phone +49 5206 91732-31
Fax +49 5206 91732-35
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
35075 Gladenbach
GERMANY
Phone +49 6462 4071-10
Fax +49 6462 4071-11
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
59519 Möhnesee-Völlinghausen
GERMANY
Phone +49 2925 800-407
Fax +49 2925 800-408
[email protected]
Koblenz
Winfried Schaefer
Hinter der Kirch 10
56767 Uersfeld
GERMANY
Phone +49 2657 16-96
Fax +49 2657 16-76
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
63452 Hanau
GERMANY
Phone +49 6181 1898-12
Fax +49 6181 1898-13
[email protected]
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
86932 Pürgen
GERMANY
Phone +49 8196 99877-54
Fax +49 8196 99877-55
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
06198 Salzatal / OT Lieskau
GERMANY
Phone +49 345 55124-56
Fax +49 345 55124-57
[email protected]
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Dr.-August-Koch-Str. 1
91639 Wolframs-Eschenbach
GERMANY
Phone +49 9875 9783-170
Fax +49 9875 9783-171
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-19
Fax +49 40 538092-84
[email protected]
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
77704 Oberkirch
GERMANY
Phone +49 7802 9822-52
Fax +49 7802 9822-53
[email protected]
fan agent
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
73207 Plochingen
GERMANY
Phone +49 7153 9289-80
Fax +49 7153 9289-81
[email protected]
compact fan agent
motor specialist
ebm-papst Landshut GmbH
Hofmark-Aich-Straße 25
84030 Landshut
GERMANY
Phone +49 871 707-0
Fax +49 871 707-465
[email protected]
Ulm
M.Sc. Reinhard Sommerreißer
Am Silbermannpark 10
86161 Augsburg
GERMANY
Phone +49 821 6610-7023
Fax +49 821 6610-7024
[email protected]
Distributoren
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
63110 Rodgau - Jügesheim
GERMANY
Phone +49 6106 841-0
Fax +49 6106 841-111
[email protected]
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
Munich
A. Schweiger GmbH
Ohmstraße 1
82054 Sauerlach
GERMANY
Phone +49 8104 897-0
Fax +49 8104 897-90
[email protected]
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
22339 Hamburg
GERMANY
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
74677 Dörzbach
GERMANY
Phone +49 7937 80355-20
Fax +49 7937 80355-25
[email protected]
www.hds-gmbh.net
motor agent
ebm-papst in Europe
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
4030 Linz
AUSTRIA
Phone +43 732 321150-0
Fax +43 732 321150-20
[email protected]
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
Lipkovskaya Gasse 34
Office No.6, Room 106,107
223010 Minsk
BELARUS
Phone +375 17 3851556
Fax +375 17 3851556
[email protected]
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
3001 Heverlee-Leuven
BELGIUM
Phone +32 16 396-200
Fax +32 16 396-220
[email protected]
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
[email protected]
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
620 00 Brno
CZECH REPUBLIC
Phone +420 544 502-411
Fax +420 547 232-622
[email protected]
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
2605 Brøndby
DENMARK
Phone +45 43 631111
Fax +45 43 630505
[email protected]
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
75301 Rae Vald, Harjumaa
ESTONIA
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
02760 Espoo
FINLAND
Phone +358 9 887022-0
Fax +358 9 887022-13
[email protected]
www.ebmpapst.fi
France
ebm-papst sarl
ZI Nord - rue A. Mohler
BP 62
67212 Obernai Cedex
FRANCE
Phone +33 820 326266
Fax +33 3 88673883
[email protected]
www.ebmpapst.fr
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
17672 Kallithea-Attiki
GREECE
Phone +30 210 9513-705
Fax +30 210 9513-490
[email protected]
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Iceland
RJ Engineers
Stangarhyl 1a
110 Reykjavik
ICELAND
Phone +354 567 8030
Fax +354 567 8015
[email protected]
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
Portlaoise, Co. Laois
IRELAND
Phone +353 57 8664343
Fax +353 57 8664346
[email protected]
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
22076 Mozzate (Co)
ITALY
Phone +39 0331 836201
Fax +39 0331 821510
[email protected]
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
51
ebm-papst in Europe
Netherlands
ebm-papst Benelux B.V.
Engelseweg 127
5705 AC Helmond
NETHERLANDS
Phone +31 492 502-900
Fax +31 492 502-950
[email protected]
www.ebmpapst.nl
Russia
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
620102 Ekaterinburg
RUSSIA
Phone +7 343 2338000
Fax +7 343 2337788
[email protected]
www.ebmpapst.ur.ru
Switzerland
ebm-papst AG
Rütisbergstrasse 1
8156 Oberhasli
SWITZERLAND
Phone +41 44 73220-70
Fax +41 44 73220-77
[email protected]
www.ebmpapst.ch
Norway
ebm-papst AS
P.B. 173 Holmlia
1203 Oslo
NORWAY
Phone +47 22 763340
Fax +47 22 619173
[email protected]
www.ebmpapst.no
ebm-papst Rus GmbH
proezd 4529, vladenie 5, stroenie 1
141000 Mytistschi, Oblast Moskau
RUSSIA
Phone +7 495 9807524
Fax +7 495 5140924
[email protected]
www.ebmpapst.ru
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
35620 Cigli-Izmir
TURKEY
Phone +90 232 3282090
Fax +90 232 3280270
[email protected]
www.ebmpapst.com.tr
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
03236 Warszawa
POLAND
Phone +48 22 6757819
Fax +48 22 6769587
[email protected]
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
2615-178 Alverca do Ribatejo
PORTUGAL
Phone +351 218 394 880
Fax +351 218 394 759
[email protected]
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
500327 Brasov
ROMANIA
Phone +40 268 331859
Fax +40 268 312805
[email protected]
52
fan agent
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
1044 Budapest
HUNGARY
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
28830 San Fernando de Henares (Madrid)
SPAIN
Phone +34 91 6780894
Fax +34 91 6781530
[email protected]
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
17562 Järfälla
SWEDEN
Phone +46 10 4544400
Fax +46 8 362306
[email protected]
www.ebmpapst.se
compact fan agent
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 21
03067 Kiev
UKRAINE
Phone +38 044 2063091
Fax +38 044 2063091
[email protected]
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
Chelmsford Essex CM2 5EZ
UNITED KINGDOM
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
East Ilsley, Berkshire RG20 7LG
UNITED KINGDOM
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&[email protected]
www.ebmpapst-ad.com
motor specialist
motor agent
ebm-papst in America and Africa
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
ARGENTINA
Phone +54 11 46576135
Fax +54 11 46572092
[email protected]
www.ebmpapst.com.ar
Brasil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
06707-100 Cotia - São Paulo
BRAZIL
Phone +55 11 4613-8700
Fax +55 11 4777-1456
[email protected]
www.ebmpapst.com.br
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
Farmington, CT 06034
UNITED STATES
Phone +1 860 674-1515
Fax +1 860 674-8536
[email protected]
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
Dearborn, MI 48120
UNITED STATES
Phone +1 313 406-8080
Fax +1 313 406-8081
[email protected]
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
2040 Honeydew
SOUTH AFRICA
Phone +27 11 794-3434
Fax +27 11 794-5020
[email protected]
www.ebmpapst.co.za
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
Pickering, Ontario, L1W3J9
CANADA
Phone +1 905 420-3533
Fax +1 905 420-3772
[email protected]
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
Mexico 05120, D.F.
MEXICO
Phone +52 55 3300-5144
Fax +52 55 3300-5243
[email protected]
www.ebmpapst.com.mx
53
ebm-papst in Asia and Australia
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
200131 Shanghai
P.R. of CHINA
Phone +86 21 5046-0183
Fax +86 21 5046-1119
[email protected]
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Room 17E, MG Tower
133 Hoi Bun Road, Kwun Tong
Hong Kong
P.R. of CHINA
Phone +852 2145-8678
Fax +852 2145-7678
[email protected]
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
11120 Nonthaburi
THAILAND
Phone +66 2 8353785-7
Fax +66 2 8353788
[email protected]
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
B 6-2, Digital Media City (DMC)
Sangam-Dong, Mapo-Gu
Seoul 121-270
KOREA
Phone +82 2 366213-24
Fax +82 2 366213-26
[email protected]
www.ebmpapst.co.kr
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
Dubai
UNITED ARAB EMIRATES
Phone +971 4 88608-26
Fax +971 4 88608-27
[email protected]
www.ebmpapst.ae
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
Chennai-600118
INDIA
Phone +91 44 25372556
Fax +91 44 25371149
[email protected]
www.ebmpapst.in
Malaysia
ebm-papst Malaysia
Representative Office
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
47600 Subang Jaya
MALAYSIA
Phone +60 3 8024-1680
Fax +60 3 8024-8718
[email protected]
Indonesia
ebm-papst Indonesia
Representative Office
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
15321 Tangerang
INDONESIA
Phone +62 21 5376250
Fax +62 21 5388305
[email protected]
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
Singapore 408620
SINGAPORE
Phone +65 65513789
Fax +65 68428439
[email protected]
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
Kiryat Arie, Petach-Tikva 49514
ISRAEL
Phone +972 3 9100300
Fax +972 3 5796679
[email protected]
www.polak.co.il
54
Japan
ebm-papst Industries Japan K.K.
12th Floor, Benex S-3 Bldg.
3-20-8 Shinyokohama, Kohoku-ku
222-0033 Yokohama
JAPAN
Phone +81 45 47057-51
Fax +81 45 47057-52
[email protected]
www.ebmpapst.jp
fan agent
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
Tsow-Inn District, Kaohsiung
TAIWAN
Phone +886 7 557-4268
Fax +886 7 557-2788
[email protected]
www.ebmpapst.com.tw
compact fan agent
motor specialist
Vietnam
ebm-papst Vietnam
Representative Office
Room #102, 25 Nguyen Van Thu Street
District 1
Ho Chi Minh City
VIETNAM
Phone +84 8 39104099
Fax +84 8 39103970
[email protected]
Australia
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
Laverton North, Victoria, 3026
AUSTRALIA
Phone +61 3 9360-6400
Fax +61 3 9360-6464
[email protected]
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
61 Hugo Johnston Drive, Unit H
Penrose 1061, Auckland
NEW ZEALAND
PO Box 112278,
Penrose 1642, Auckland
Phone +64 9 525-0245
Fax +64 9 525-0246
[email protected]
www.ebmpapst.com.au
motor agent
55
www.ebmpapst.com
37903-7-8811 · 2013-11 · KH-3’
Printed in Germany
ebm-papst
Mulfingen GmbH & Co. KG
Bachmühle 2
74673 Mulfingen
Germany
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
The engineer’s choice