Axial-fan ESM-iQ EN

Energy-saving fans
with ESM, ACi and iQ/iQ2-motor
The engineer’s choice
version 2012-10
The new generation of energy-saving fans
Energy savings have become an important topic in almost every aspect of life. Our extended energy
saving fan series, based on the energy saving motor (ESM) and the iQ-motor, offers high efficiency
throughout a long service life and a significant decrease in energy consumption along with it. This is
precisely what is required for refrigeration systems, such as in refrigerated and freezer cases or for
condensing units.
Comprehensive series
The series of these energy saving fans includes the compact fan series of ACi 4400 as well as
based on the energy saving motor (ESM), axial fans and centrifugal modules as well as the iQ-motor
as an energy saving variant of the Q-motor.
Axial fans are available in sizes of 130, 172, 200, 230, 250 and 300 mm plus the compact fan ACi
4400 with the dimensions 119 x 119 x 38 mm. With their new rotors and wall rings, which have
been optimised according to aerodynamic criteria, the fans now work even more quietly and require
no varnish, a particularly environmentally friendly feature.
Energy saving centrifugal modules are available in sizes of 190 and 220 mm. These are especially
appealing due to their compact and aerodynamically optimised design, which allows customers to
install them quickly and hassle-free.
The K1G200 energy saving centrifugal module in a diagonal impeller design rounds out the ESM
series. It particularly distinguishes itself due to noise-optimised and air flow-optimised performance
in the medium pressure range. ebm-papst sets the benchmark here, too.
The existing series was expanded with additional versions and functions to meet new market demands. Among other things, this includes a 24 VDC design with an integrated 0-10 VDC open loop
speed control and a speed monitoring output.
A 0-10 VDC open loop speed control is now possible even for the existing line-fed designs by using
an ESM+ plug-in module.
This series is supplemented by the energy saving iQ-motor based on ebm-papst's GreenTech EC
technology. The iQ2 series further expands the offering with additional functions. Due to its dimensions and mounting options, which are identical to the Q-motor already established on the market,
customers are given the possibility of a 1:1 replacement without extensive renovations.
The iQ-motor can be readily installed with normal axial impellers with a 154 to 254 mm diameter.
Maximum efficiency
Our fans and motors achieve a maximum motor efficiency of over 70% and thus only need 1/3 to
1/6 of the power of an otherwise normal shaded-pole motor. Higher efficiency also means lower intrinsic heating during operation at the same time, which dissipates less heat into the surrounding
area. This means that less cooling power must be generated, thus resulting in additional energy
savings.
2
Table of contents
The new generation of energy-saving fans
2
Green Tech: The Green Company
4
Energy-saving axial fans
6
Energy-saving centrifugal modules
32
ESM/ACi accessories
40
ESM electrical connections
46
iQ/iQ2-motor
48
iQ/iQ2-motor accessories
58
Technical parameters & scope
62
ebm-papst representatives & subsidiaries
66
3
Sustainability is at the centre of our
thoughts and actions. Out of conviction!
Eco-friendliness and sustainability have always been at the core of our thoughts and actions. For decades, we have worked
according to the simple but strict creed of our co-founder Gerhard Sturm: “Each new product we develop has to be better
than the last one in terms of economy and ecology.” GreenTech is the ultimate expression of our corporate philosophy.
GreenTech is pro-active development.
GreenTech is acknowledged and certified.
Even in the design phase, the materials and processes we use are optimi-
Every step in our chain of production meets the stringent standards of
sed for the greatest possible eco-friendliness, energy balance and –
environmental specialists and the public. The 2008 Environmental Prize
wherever possible – recyclability. We continually improve the material
of Baden-Wuerttemberg, the Green Award 2009, the Energy Efficiency
and performance of our products, as well as the flow and noise charac-
Award 2009 of the dena – to give just a few examples – testify to this.
teristics. At the same time, we significantly reduce energy consumption.
The environmental advantage gained in the performance of the products
Close co-operation with universities and scientific institutes and the pro-
developed from our GreenTech philosophy can also be measured in the
fessorship we endow in the area of power engineering and regenerative
fulfilment of the most stringent energy and environmental standards.
energies allows us to profit from the latest research findings in these
In many instances, our products are already well below the thresholds
fields – and at the same time ensure highly qualified young academics.
energy legislation will impose a few years from now – several times over.
GreenTech is eco-friendly production.
Our customers profit from this every day.
GreenTech also stands for maximum energy efficiency in our production
The heart of GreenTech is future-oriented EC technology from ebm-
processes. There, the intelligent use of industrial waste heat and ground-
papst. The EC technology at the core of our most efficient motors and
water cooling, photovoltaics and, of course, our own cooling and venti -
fans allows efficiency of up to 90%, saves energy at a very high level,
lation technology are of the utmost importance. Our most modern plant,
significantly extends service life and makes our products maintenance-
for instance, consumes 91% less energy than currently specified and
free. These values pay off not only for the environment, but every cent al-
required. In this way, our products contribute to protecting the environ-
so pays off for the user! All ebm-papst products – even those for which
ment, from their origin to their recyclable packaging.
GreenTech EC technology does not (yet) make sense from an application
viewpoint – feature the greatest possible connection of economy and
ecology.
5
Series: The existing series of energy saving axial fans was expanded by adding the ACi 4400 series
and a compact fan with size 130. In addition, the ESM series is now available as a 24 VDC version
with an integrated 0-10 VDC open loop speed control output and a speed monitoring signal. These
control options have also become possible for line-fed designs via an additional ESM+ plug-in
module.
System: Not just our existing shaded-pole motors were replaced by high-efficiency GreenTech EC
motors for our fans, but a complete new system was developed as a whole consisting of an EC
motor, impeller and wall ring. Optimum efficiency for the best possible noise behaviour was only
able to be achieved by having all of the components perfectly harmonised together.
Energy efficiency: The energy saving motors achieve a maximum efficiency of over 70%. So they
only need 1/3 to 1/6 the power of an otherwise normal shaded-pole motor. But higher efficiency
also means lower intrinsic heating during operation at the same time, which dissipates less heat
into the surrounding area. This results in further energy savings, since less cooling capacity needs
to be put in place from the beginning.
Easy installation: Effort needed by the customer for installation and logistics is reduced to a minimum due to the complete system. In addition to the fan itself, only screws are needed for mounting.
Further savings result from the pluggable connection line. For example, this allows installation time
to be drastically reduced due to a pre-installed cable harness. The number of variants can be substantially reduced by subsequent programming as well by having different air performance levels
customised accordingly – even at a later point in time. An earth wire can be omitted due to a design
in protection class 2.
Robust design (ESM): Ten years of field experience with more than 3 million energy saving motors
shows that the system is robust, maintenance-free and durable. Depending on environmental conditions, the service life usually exceeds 60,000 hours. The stator, which is hermetically sealed with a
coat of plastic, is optimally protected from ambient influences. And the electronics are protected
from humidity with a sealed off cover, so that IP 54 protection requirements are fulfilled. Shock
loads of more than 50g have no effect on the fan due to the stable design.
Certifications:
ACi 4400: UL (507), VDE (EN 60950), CSA
ESM: All of the approvals required in the refrigerated case industry are present
or in progress.
VDE: EN 60335-1, -2-24, -2-80, -2-89
UL 1004-1, 1004-3, UL 60730 and GOST
6
The new energy-saving axial fans
ACI 4400
8
ESM Size 130, 172
10
ESM Size 200, 230, 250
14
ESM Size 300
28
7
Energy-saving axial fans
Series ACi 4400
119 x 119 x 38 mm
Input power
Current draw
Sound pressure level
VAC
Hz
rpm
W
mA
dB(A)
Mass
Speed/rpm
Type
Perm. amb. temp.
Frequency
Nominal data
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics
– Moisture protection: Motor and circuit
board are coated
– Electrical connection: Plug-in connection
lateral
– Protection class: II
– Product conforming to standard: CE
– Approvals: UL (507), VDE (EN 60950),
CSA
Sound power level
Nominal voltage
range
VAC
Curve
Nominal voltage
– Material: Housing: Plastic PBT
fibreglass-reinforced
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Clockwise, seen
on rotor
– Insulation class: "E"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Bel(A)
°C
kg
ACi 4420 ML
A
1~ 230
195...265
50/60
1850
1,4
17
25
4,1
-20..+75
0,25
ACi 4420 H
B
1~ 230
195...265
50/60
3000
3,3
35
39
5,1
-20..+75
0,25
ACi 4420 HH
C
1~ 230
195...265
50/60
3350
4,4
41
42
5,3
-20..+75
0,25
ACi 4410 HH
D
1~ 115
85...132
50/60
3350
4,4
82
42
5,3
-20..+75
0,25
subject to alterations
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
and without protection against
D
C
accidental contact
60
0,2
50
I
mA
1
1850
1,4
17
A
2
1850
1,5
18
A
3
1850
1,6
19
A
4
1850
1,7
19
B
1
3000
3,3
35
only valid under the measur-
B
2
3000
3,9
39
ment conditions listed and
B
3
3000
3,9
44
may vary depending on the
B
4
3000
4,7
46
C
1
3350
4,4
41
C
2
3350
5,1
48
C
3
3350
5,7
53
C
4
3350
5,9
55
D
1
3350
4,4
82
D
2
3350
5,1
96
D
3
3350
5,7
106
D
4
3350
5,9
110
The acoustic values given are
B
Pe
W
A
Installation category A,
70
n
rpm
installation situation.
40
With any deviation to the standard setup, the specific values
4
have to be checked and re-
30
viewed once installed or fitted!
4
0,1
3
A
For detailed information
3
20
see Compact fans catalogue
2
2
4
10
version 2011, p. 8-16
3
2
pfs
qV
8
20
0
25
1
60
40
50
75
100
1
125
1
100
80
150
175
cfm
m3/h
– Electr. connection:
L
ACi 4400
N
119 ±0.3
104.8 ±0.2
A-A
38 ±0.5
A
6±
R 0.3
3
.3
±0
.
15
0.
Ø4
A
6±
0.
3
±0
.1
5
R 0.3
Ø4
.3
"B"
❮ "V"
"A"
Plug connection on
both sides possible.
9
Accessories
p. 44 ff.
Energy-saving axial fans
Ø 130
– Material: Wall ring: Plastic PP, fibreglassreinforced; Blade:Plastic PA,
fibreglass-reinforced
– Number of blades: 7
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
3200
24
0,38
90
-30..+60
0,75
1~ 230
50/60
3200
24
0,19
90
-30..+70
0,75
Curve
Nominal data
Type
Motor
W1G130-AA49 -01
M1G 055-AI
A
W1G130-AA25 -01
M1G 055-AI
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE;
EN 60335-1
– Approvals: VDE, UL, CSA, GOST are
applied for
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
90
Air performance measured
as per: ISO 5801,
in ebm-papst full nozzle
and without protection against
80
accidental contact
60
7
3200
23
0,38
63
2
3200
24
0,38
61
A
3
3200
24
0,38
60
A
4
3200
24
0,38
63
5
2800
16
0,26
60
A
6
2800
16
0,26
58
LWA as per ISO 13347,
A
7
2800
16
0,26
57
LpA measured at 1 m distance
A
8
2800
16
0,26
60
B
1
3200
23
0,19
63
B
2
3200
24
0,19
61
B
3
3200
24
0,19
60
B
4
3200
24
0,19
63
B
5
2800
16
0,13
60
B
6
2800
16
0,13
58
dard setup, the specific values
B
7
2800
16
0,13
57
have to be checked and re-
B
8
2800
16
0,13
60
only valid under the measurment conditions listed and
40
may vary depending on the
installation situation.
30
0,1
2
With any deviation to the stan-
6
20
viewed once installed or fitted!
10
For detailed information
5
pfs
qV
40
50
80
100
n max. = 3200 min-1
10
1
A
A
The acoustic values given are
0
160
120
150
200
n = 2800 min-1
250
LWA
dB(A)
to fan axis
0,2
50
3
I
A
Suction-side noise levels:
0,3
8
70
Pe
W
A
Installation category A,
4
n
rpm
200
300
n min. = 1100 min-1
see page 62 ff.
1
350
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
Ø151±0.5
A-A
0.
1
Ø4 Ø5
.2 ±
10
5
1.
58 -1
62
A
Ø4
.2
±0
Ø 5 .1
Ø1
Ø1
7
2±
+ 0.
-0 0.1 5
.3
5
10
1.
55±0.3
40±5
6
450 +20
❮ "V"
A
Connection lead (total length 450 mm)
is fitted ex works and can be detached.
11
Handheld Programmer p. 41
Energy-saving axial fans
Ø 172
– Material: Wall ring: Plastic PP
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
2500
21
0,30
60
-30..+50
0,95
1~ 230
50/60
2500
22
0,18
60
-30..+50
0,95
Curve
Nominal data
Type
Motor
W1G172-EC95 -01
M1G 055-BD
A
W1G172-EC91 -01
M1G 055-BD
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
Air performance measured
as per: ISO 5801,
0,24
60
4
and without protection against
40
0,16
50
0,20
accidental contact
1
2500
20
0,28
62
A
2
2500
21
0,30
63
A
3
2500
21
0,30
63
A
4
2500
21
0,30
63
5
1700
9
0,14
54
A
6
1700
10
0,16
53
LWA as per ISO 13347,
A
7
1700
10
0,16
53
LpA measured at 1 m distance
A
8
1700
10
0,16
54
B
1
2500
21
0,17
62
B
2
2500
22
0,18
63
B
3
2500
22
0,18
63
B
4
2500
22
0,18
63
B
5
1700
9
0,07
54
B
6
1700
10
0,08
53
dard setup, the specific values
B
7
1700
10
0,08
53
have to be checked and re-
B
8
1700
10
0,08
54
to fan axis
3
0,12
only valid under the measurment conditions listed and
8
0,04
10
0,08
installation situation.
2
7
With any deviation to the stan-
viewed once installed or fitted!
6
For detailed information
pfs
0
qV
50
100
n max. = 2500 min-1
12
100
5
200
150
200
300
n = 1700 min-1
see page 62 ff.
1
250
400
LWA
dB(A)
A
may vary depending on the
20
I
A
Suction-side noise levels:
The acoustic values given are
30
Pe
W
A
Installation category A,
in ebm-papst full nozzle
n
rpm
300
500
n min. = 900 min-1
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
78.5
4x Ø4.3
Ø222
Ø208
6
4
40±5
450+20
Ø172
Ø19
2
35
❮ "V"
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
13
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 200
– Material: Wall ring:
Plastic PP
epylen
Blade: Plastic PA,
fibreglass-reinforced
Number of blades: 5
Direction of air flow:
"V", exhaust over struts
Direction of rotation: Counter-clockwise,
seen on rotor
Type of protection: IP 54
Insulation class: "B"
Mounting position: Any
Condensate discharges: None
– Mode of operation: Con. operation (S1)
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
A
B
–
–
–
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
1300
8,0
0,11
23
-30..+50
1,0
1~ 230
50/60
1300
8,0
0,07
23
-30..+50
1,0
Curve
Nominal voltage
–
–
–
–
Nominal data
Type
Motor
W1G200-EC91 -27
M1G 055-BD
A
W1G200-EC87 -25
M1G 055-BD
B
subject to alterations
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
Air performance measured
as per: ISO 5801,
0,10
25
and without protection against
accidental contact
0,08
3
1
1300
7
0,09
50
A
2
1300
8
0,10
49
A
3
1300
8
0,10
48
A
4
1300
8
0,11
51
A
5
900
3
0,05
41
A
6
900
4
0,05
41
LWA as per ISO 13347,
A
7
900
4
0,05
40
LpA measured at 1 m distance
A
8
900
4
0,05
41
B
1
1300
7
0,06
50
B
2
1300
8
0,07
49
B
3
1300
8
0,07
48
B
4
1300
8
0,07
51
B
5
900
3
0,03
41
B
6
900
4
0,04
41
dard setup, the specific values
B
7
900
4
0,04
40
have to be checked and re-
B
8
900
4
0,04
41
The acoustic values given are
only valid under the measurment conditions listed and
may vary depending on the
8
0,04
10
installation situation.
2
0,02
7
5
With any deviation to the stan-
6
viewed once installed or fitted!
For detailed information
5
pfs
0
qV
50
100
n max. = 1300 min-1
14
100
150
200
n = 900 min-1
see page 62 ff.
1
200
300
LWA
dB(A)
to fan axis
0,06
15
I
A
Suction-side noise levels:
4
20
Pe
W
A
Installation category A,
in ebm-papst full nozzle
n
rpm
250
400
n min. = 500 min-1
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
78.5
4x Ø4.3
Ø250
Ø236
6
4
40±5
450+20
Ø200
Ø22
0
40
❮ "V"
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
15
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 200
– Material: Wall ring: Plastic PP
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
2100
31
0,46
55
-30..+50
1,0
1~ 230
50/60
2100
31
0,24
55
-30..+50
1,0
Curve
Nominal data
Type
Motor
W1G200-EC95 -47
M1G 055-BD
A
W1G200-EC91 -45
M1G 055-BD
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
Air performance measured
as per: ISO 5801,
0,24
in ebm-papst full nozzle
and without protection against
accidental contact
40
0,16
50
0,20
4
1
2100
28
0,42
62
A
2
2100
30
0,45
61
A
3
2100
31
0,46
60
A
4
2100
31
0,46
62
5
1500
14
0,22
54
A
6
1500
15
0,22
54
LWA as per ISO 13347,
A
7
1500
16
0,26
53
LpA measured at 1 m distance
A
8
1500
16
0,26
55
B
1
2100
29
0,22
62
B
2
2100
30
0,23
61
B
3
2100
31
0,24
60
B
4
2100
31
0,24
62
B
5
1500
14
0,11
54
B
6
1500
16
0,12
54
dard setup, the specific values
B
7
1500
16
0,13
53
have to be checked and re-
B
8
1500
16
0,13
55
to fan axis
3
0,12
only valid under the measurment conditions listed and
8
installation situation.
0,08
7
2
0,04
With any deviation to the stan-
10
6
viewed once installed or fitted!
For detailed information
pfs
0
qV
50
100
100
n max. = 2100 min-1
16
150
200
200
300
250
400
n = 1500 min-1
5
300
500
see page 62 ff.
1
350
600
n min. = 800 min-1
LWA
dB(A)
A
may vary depending on the
20
I
A
Suction-side noise levels:
The acoustic values given are
30
Pe
W
A
Installation category A,
60
n
rpm
400
700
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
78.5
4x Ø4.3
Ø250
Ø236
6
4
40±5
450+20
Ø200
Ø22
0
40
❮ "V"
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
17
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 200
– Material: Wall ring: epylen
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Nominal
voltage range
Speed/rpm(1)
Input power(1)
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VDC
VDC
rpm
W
A
Pa
°C
kg
A
24
16-28
1550
11
0,50
30
-30..+50
1,0
B
24
16-28
2130
29
1,50
55
-30..+50
1,0
Curve
Nominal data
Type
Motor
W1G200-EF41 -01
M1G 055-BD
W1G200-EF01 -01
M1G 055-BD
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Approvals: VDE, UL, CSA, GOST are
applied for
– Technical features: Control input 0-10
VDC / PWM, Tach output
(1) Nominal data running at free air.
70
in H2O
Air performance measured
as per: ISO 5801,
in ebm-papst full nozzle
and without protection against
0,24
60
accidental contact
4
0,20
50
B
53
A
3
1510
11
0,51
52
A
4
1515
11
0,51
55
1,50
62
30
1,56
62
LWA as per ISO 13347,
B
3
2050
31
1,61
61
LpA measured at 1 m distance
B
4
2050
31
1,62
59
0,16
0,12
0,08
With any deviation to the stan-
2
3
0,04
viewed once installed or fitted!
2
For detailed information
200
100
0
pfs
54
0,50
29
may vary depending on the
A
1
18
0,50
11
2085
have to be checked and re-
qV
11
1530
2130
dard setup, the specific values
10
1550
2
2
installation situation.
20
1
A
1
ment conditions listed and
4
100
200
300
300
400
500
see page 62 ff.
1
400
600
700
500 cfm
800
m3/h
LWA
dB(A)
B
only valid under the measur-
30
I
A
B
The acoustic values given are
3
Pe
W
Suction-side noise levels:
to fan axis
40
n
rpm
A
Installation category A,
0,28
Pa
Curves
– Electr. connection:
1
4
UN +24 VDC
UB
PWM/0-10 VDC
RE>100K
Tacho
3
680 R
Tacho
47 V
GND
2
GND1
Reverse-polarity
protection
78.5
4x Ø4.3
Ø250
Ø236
6
4
40±5
450+20
Ø200
Ø22
0
40
❮ "V"
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
19
Accessories
p. 41
Electr. connection
p. 46
Energy-saving axial fans
Ø 200
– Material: Wall ring: epylen
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 230
50/60
1300
8
0,07
23
-30..+50
1,0
1~ 230
50/60
2100
31
0,24
55
-30..+50
1,0
Curve
Nominal data
Type
Motor
W1G200-EC87 -A2
M1G 055-BD
A
W1G200-EC91 -A4
M1G 055-BD
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE;
EN 60335-1
– Approvals: VDE, UL, CSA, GOST are
applied for
– Technical features: Control input 0-10
VDC / PWM, Output 10 VDC max. 1.1 mA,
Tach output
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Air performance measured
in H2O
Pa
Curves
as per: ISO 5801,
4
0,20
50
and without protection against
accidental contact
0,16
3
0,12
0,08
0,04
pfs
20
500
4
1300
8,0
0,07
48
62
B
3
2100
31
0,24
60
LpA measured at 1 m distance
B
4
2100
31
0,24
59
see page 62 ff.
1
300
400
48
A
LWA as per ISO 13347,
For detailed information
300
0,07
62
have to be checked and re-
1
200
8,0
0,24
viewed once installed or fitted!
100
1300
0,23
dard setup, the specific values
qV
3
30
installation situation.
2
200
49
A
29
With any deviation to the stan-
100
50
0,07
2100
3
0
0,06
8,0
2100
may vary depending on the
2
A
7,0
1300
2
ment conditions listed and
10
1300
2
1
only valid under the measur-
20
1
A
B
The acoustic values given are
4
400
600
700
cfm
m3/h
LWA
dB(A)
B
to fan axis
30
I
A
Suction-side noise levels:
B
40
Pe
W
A
Installation category A,
in ebm-papst full nozzle
n
rpm
– Electr. connection:
CON10
L
AC1
1
N
2
1.25A
P
AC2
N
CON50
+10V
1
Imax=1.1mA
3
10V/PWM
47k
47k
100μF
GND
4
2
Tacho
1
680R
ZMM47
2
105.5
78.5
Ø4.3(4x)
Ø200
Ø236
Ø250
Ø22
0
40
4
40 ±5
6
6
40 ±5
1000 +20
450 +20
❮ "V"
21
Accessories
p. 40 ff.
Electr. connection
p. 47
Energy-saving axial fans
Ø 200
– Material: Blade: Plastic PA,
fibreglass-reinforced
Guard grille: epylen
– Number of blades: 5
– Direction of air flow: "A", intake over
guard grille
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
2000
31
0,43
45
-30..+50
0,95
1~ 230
50/60
2000
34
0,26
45
-30..+50
0,95
Curve
Nominal data
Type
Motor
S1G 200-CA95 -02
M1G 055-BD
A
S1G 200-CA91 -02
M1G 055-BD
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Air performance measured
in H2O
Pa
Curves
A
B
as per: ISO 5801,
0,20
50
and with protection against
accidental contact
0,16
I
A
LWA
dB(A)
1
2000
30
0,43
64
A
2
2000
30
0,43
64
A
3
2000
30
0,43
63
A
4
2000
31
0,43
64
A
5
1500
17
0,28
59
Suction-side noise levels:
A
6
1500
18
0,28
58
LWA as per ISO 13347,
A
7
1500
19
0,28
58
LpA measured at 1 m distance
A
8
1500
20
0,28
59
B
1
2000
32
0,24
64
B
2
2000
33
0,25
64
B
3
2000
33
0,25
63
B
4
2000
34
0,26
64
B
5
1500
18
0,16
59
B
6
1500
19
0,16
58
dard setup, the specific values
B
7
1500
19
0,16
58
have to be checked and re-
B
8
1500
20
0,16
59
4
40
Pe
W
A
Installation category A,
in ebm-papst short nozzle
n
rpm
30
0,12
to fan axis
The acoustic values given are
3
only valid under the measur8
ment conditions listed and
20
0,08
may vary depending on the
installation situation.
7
With any deviation to the stan-
10
0,04
2
6
viewed once installed or fitted!
For detailed information
5
pfs
0
qV
50
100
100
n max. = 2000 min-1
22
150
200
200
300
250
400
n = 1500 min-1
300
500
see page 62 ff.
1
350
600
n min. = 800 min-1
400
700
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
S
off
on (L1 or N)
Speed selection
n1
n2
38.5
3
4x Ø6.5
6
"A" ❯
380 ±20
40±5
37.5
Ø260
Ø278
Ø200
40
brown
S
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
23
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 230
– Material: Wall ring: Plastic PP
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
1500
23
0,35
36
-30..+50
1,05
1~ 230
50/60
1500
26
0,20
36
-30..+50
1,05
Curve
Nominal data
Type
Motor
W1G230-EB97 -01
M1G 055-BD
A
W1G230-EB89 -01
M1G 055-BD
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
Air performance measured
A
as per: ISO 5801,
B
0,16
40
and without protection against
accidental contact
30
0,12
4
3
1
1500
23
0,35
58
A
2
1500
23
0,35
58
A
3
1500
23
0,35
58
A
4
1500
23
0,35
57
5
1000
9
0,15
48
A
6
1000
10
0,16
48
LWA as per ISO 13347,
A
7
1000
10
0,16
48
LpA measured at 1 m distance
A
8
1000
10
0,16
48
B
1
1500
24
0,19
58
B
2
1500
25
0,19
58
B
3
1500
25
0,19
58
B
4
1500
26
0,20
57
B
5
1000
10
0,09
48
B
6
1000
11
0,09
48
dard setup, the specific values
B
7
1000
11
0,10
48
have to be checked and re-
B
8
1000
11
0,10
48
to fan axis
0,08
ment conditions listed and
may vary depending on the
installation situation.
8
2
7
0,04
With any deviation to the stan-
viewed once installed or fitted!
6
For detailed information
5
pfs
0
qV
100
200
n max. = 1500 min-1
24
200
300
400
n = 1000 min-1
1
400
600
LWA
dB(A)
A
only valid under the measur-
10
I
A
Suction-side noise levels:
The acoustic values given are
20
Pe
W
A
Installation category A,
in ebm-papst full nozzle
n
rpm
500
800
n min. = 700 min-1
cfm
m3/h
see page 62 ff.
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
78.5
4x Ø4.3
Ø280
Ø266
6
4
40±5
450+20
Ø230
Ø25
0
50
❮ "V"
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
25
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 250
M1G 055-BI
B
subject to alterations
Mass
W1G250-BB17 -01
Perm. amb. temp.
A
Max. back pressure
M1G 055-BI
Max.
current draw(1)
W1G250-BB21 -01
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
Nominal voltage
Curve
– Material: Wall ring: Plastic PP
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
1700
32
0,47
40
-30..+50
1,55
1~ 230
50/60
1700
32
0,24
40
-30..+50
1,55
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
Air performance measured
as per: ISO 5801,
30
0,16
4
accidental contact
0,12
40
and with protection against
3
1
1700
30
0,44
62
A
2
1700
31
0,45
63
A
3
1700
32
0,47
64
A
4
1700
32
0,47
65
A
5
1200
14
0,22
53
A
6
1200
15
0,24
54
LWA as per ISO 13347,
A
7
1200
16
0,25
55
LpA measured at 1 m distance
A
8
1200
17
0,26
57
B
1
1700
30
0,24
62
B
2
1700
31
0,24
63
B
3
1700
32
0,24
64
B
4
1700
32
0,24
65
B
5
1200
14
0,12
53
B
6
1200
15
0,13
54
dard setup, the specific values
B
7
1200
16
0,14
55
have to be checked and re-
B
8
1200
17
0,14
57
only valid under the measur-
0,08
ment conditions listed and
may vary depending on the
installation situation.
7
2
0,04
With any deviation to the stan-
6
viewed once installed or fitted!
For detailed information
5
pfs
0
qV
100
200
n max. = 1700 min-1
26
200
300
400
1
400
600
n = 1200 min-1
500
800
n min. = 900 min-1
LWA
dB(A)
to fan axis
8
10
I
A
Suction-side noise levels:
The acoustic values given are
20
Pe
W
A
Installation category A,
in ebm-papst full nozzle
n
rpm
cfm
1000
m3/h
see page 62 ff.
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
92
80
296
4x90˚
4
Ø280
Ø250
4xØ7
45˚
95
Ø2 315
Ø
40±5
6
❮ "V"
340 ±20
27
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 300
– Material: Wall ring: Plastic PP
Blade: Plastic PA,
fibreglass-reinforced
– Number of blades: 5
– Direction of air flow:
"V", exhaust over struts
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
1300
35
0,50
35
-30..+50
1,75
1~ 230
50/60
1300
35
0,27
35
-30..+50
1,75
Curve
Nominal data
Type
Motor
W1G300-BB23 -01
M1G 055-BI
A
W1G300 -BB19 -01
M1G 055-BI
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Pa
in H2O
Curves
A
B
as per: ISO 5801,
4
in ebm-papst full nozzle
and with protection against
accidental contact
25
0,10
3
I
A
LWA
dB(A)
1
1300
28
0,41
58
A
2
1300
31
0,46
58
A
3
1300
32
0,47
57
A
4
1300
35
0,50
58
A
5
900
12
0,24
50
Suction-side noise levels:
A
6
900
14
0,25
49
LWA as per ISO 13347,
A
7
900
15
0,26
49
LpA measured at 1 m distance
A
8
900
16
0,27
50
B
1
1300
32
0,25
58
B
2
1300
34
0,27
58
B
3
1300
34
0,27
57
B
4
1300
35
0,27
58
B
5
900
13
0,12
50
B
6
900
14
0,13
49
dard setup, the specific values
B
7
900
15
0,14
49
have to be checked and re-
B
8
900
16
0,15
50
0,12
30
Pe
W
A
Installation category A,
0,14
35
Air performance measured
n
rpm
20
0,08
to fan axis
The acoustic values given are
only valid under the measurment conditions listed and
0,06
8
15
may vary depending on the
2
installation situation.
10
0,04
7
With any deviation to the stan-
6
viewed once installed or fitted!
0,02
5
For detailed information
5
pfs
0
qV
100
200
200
n max. = 1300 min-1
28
300
400
400
600
500
800
n = 900 min-1
see page 62 ff.
1
600
1000
700
1200
n min. = 700 min-1
800
cfm
m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
S
off
on (L1 or N)
Speed selection
n1
n2
92
80
4
45˚
Ø350
Ø300
4xØ6.3
360
4x90˚
80
Ø3 397
Ø
40±5
6
❮ "V"
290 ±20
29
Accessories
p. 40 ff.
Energy-saving axial fans
Ø 300
– Material: Blade: Plastic PA,
fibreglass-reinforced
Guard grille: epylen
– Number of blades: 5
– Direction of air flow: "A", intake over
guard grille
– Direction of rotation: Counter-clockwise,
seen on rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None
– Mode of operation: Con. operation (S1)
Nominal voltage
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Max. back pressure
Perm. amb. temp.
Mass
VAC
Hz
rpm
W
A
Pa
°C
kg
1~ 115
50/60
1250
35
0,56
35
-30..+50
1,4
1~ 230
50/60
1250
35
0,27
35
-30..+50
1,4
Curve
Nominal data
Type
Motor
S1G 300-CA23 -02
M1G 055-BI
A
S1G 300-CA19 -02
M1G 055-BI
B
subject to alterations
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Air performance measured
in H2O
Pa
Curves
A
B
as per: ISO 5801,
0,16
40
and with protection against
accidental contact
30
0,12
4
1
1250
31
0,45
64
A
2
1250
32
0,47
62
A
3
1250
32
0,48
62
A
4
1250
35
0,56
63
A
5
900
13
0,24
55
A
6
900
14
0,26
54
LWA as per ISO 13347,
A
7
900
16
0,30
53
LpA measured at 1 m distance
A
8
900
17
0,32
54
B
1
1250
27
0,21
64
B
2
1250
30
0,23
62
B
3
1250
32
0,24
62
B
4
1250
35
0,27
63
B
5
900
13
0,12
55
B
6
900
14
0,13
54
dard setup, the specific values
B
7
900
16
0,15
53
have to be checked and re-
B
8
900
17
0,16
54
The acoustic values given are
0,08
ment conditions listed and
may vary depending on the
8
installation situation.
2
With any deviation to the stan-
0,04
7
6
viewed once installed or fitted!
For detailed information
pfs
0
qV
100
200
n max. = 1250 min-1
30
LWA
dB(A)
Suction-side noise levels:
only valid under the measur-
10
I
A
to fan axis
3
20
Pe
W
A
Installation category A,
in ebm-papst short nozzle
n
rpm
200
300
400
5
500
400
600
n = 900 min-1
800
see page 62 ff.
1
600
1000
n min. = 700 min-1
700
cfm
1200 m3/h
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
43
3
S
off
on (L1 or N)
Speed selection
n1
n2
4x Ø6.5
40±5
6
"A" ❯
330 ±20
38
Ø360
Ø377
Ø300
45
brown
S
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
31
Accessories
p. 40 ff.
The perfect combination!
For the new energy saving centrifugal modules, we have combined a backward curved centrifugal
impeller already established on the market with new compact modules. The result is a highly compact unit with an integrated inlet nozzle and motor suspension directly connected to the mounting
plate. The mounting plate, inlet nozzle and motor suspension consist of a robust and durable plastic.
This has the advantage that no compromises have to be made in the aero-acoustic design.
The energy saving centrifugal modules are available with impellers with a 190 and 220 mm diameter. They are extremely compact and easy to install. Intricate adjustments to the impeller for the
nozzle are not necessary. An inlet side guard grille is available for installation as an accessory.
The new diagonal K1G200 with an energy saving motor rounds out the series. The diagonal impeller
design particularly distinguishes itself through its noise-optimised and air flow-optimised performance in the medium pressure range and sets new benchmarks in the process.
Take advantage of the benefits offered by a completely pre-installed functional unit:
– Compact design
– Optimised, tested and guaranteed functional unit
– Plug-and-play characteristic
– Easy installation
– Energy saving motor (ESM)
– Optional guard grille
– Simple logistics
Maximum efficiency
The energy saving motors achieve a maximum efficiency of over 70%. So they only need 1/3 to 1/6
the power of an otherwise normal shaded-pole motor. But higher efficiency also means lower intrinsic heating during operation at the same time, which dissipates less heat into the surrounding area.
This means that less cooling power must be generated from the outset, thus resulting in additional
energy savings.
32
The new energy-saving centrifugal modules
Size 190, backward curved
34
Size 220, backward curved
36
Size 200, diagonal
38
33
EC centrifugal module
backward curved, Ø 190
– Material: Housing: Plastic PA,
fibreglass-reinforced
Impeller: Plastic PA,
fibreglass-reinforced
Rotor: Galvanised
– Number of blades: 7
– Direction of rotation: clockwise, seen on
rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open rotor
– Mode of operation: Con. operation (S1)
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Type
Motor
K1G 190
M1G 055-BD
A
K1G 190
M1G 055-BD
B
subject to alterations
Perm. amb. temp.
Nominal voltage
VAC
Hz
rpm
W
A
°C
1~ 115
50/60
2000
30
0,45
-30..+50
1~ 230
50/60
2000
30
0,24
-30..+50
Curve
Nominal data
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST are
applied for
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Air performance measured
in H2O
Pa
Curves
A
B
as per: ISO 5801,
0,7
without protection against accidental contact
0,6
4
0,4
3
100
8
1
2000
21
0,34
62
2
2000
25
0,38
60
A
3
2000
30
0,45
59
A
4
2000
26
0,39
60
5
1600
13
0,19
57
A
6
1600
15
0,25
55
LpA measured at 1 m distance
A
7
1600
17
0,27
53
to fan axis
A
8
1600
15
0,26
55
The acoustic values given are
B
1
2000
21
0,16
62
only valid under the measur-
B
2
2000
25
0,19
60
B
3
2000
30
0,24
59
B
4
2000
26
0,20
60
B
5
1600
13
0,10
57
B
6
1600
15
0,11
55
have to be checked and re-
B
7
1600
17
0,13
53
viewed once installed or fitted!
B
8
1600
15
0,12
55
may vary depending on the
0,3
installation situation.
7
60
With any deviation to the stan-
2
0,2
dard setup, the specific values
40
6
0,1
20
A
ment conditions listed and
80
For detailed information
see page 62 ff.
5
pfs
0
qV
50
100
n max. = 2000 min-1
34
100
150
200
n = 1600 min-1
1
200
300
250
400
n min. = 700 min-1
cfm
m3/h
LWA
dB(A)
LWA as per ISO 13347,
Suction-side noise levels:
0,5
120
I
A
A
160
140
Pe
W
A
Installation category A,
180
n
rpm
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
off
on (L1 or N)
n1
n2
Mass of centrifugal
module with support
bracket
S
Speed selection
Centrifugal module
with support bracket
kg
K1G 190-AD50 -02
1,3
K1G 190-AD73 -02
1,3
109
94
16.5°
4xØ4.3
5°
4
6
4
40±5
450+20
Ø190
Ø266
Ø280
Ø256+1
8x
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
35
Accessories
p. 40 ff.
EC centrifugal module
backward curved, Ø 220
– Material: Housing: Plastic PA,
fibreglass-reinforced
Impeller: Plastic PA,
fibreglass-reinforced
Rotor: Galvanised
– Number of blades: 11
– Direction of rotation: clockwise, seen on
rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open rotor
– Mode of operation: Con. operation (S1)
Frequency
Speed/rpm(1)
Max.
input power(1)
Max.
current draw(1)
Type
Motor
K1G 220
M1G 055-BD
A
K1G 220
M1G 055-BD
B
subject to alterations
Perm. amb. temp.
Nominal voltage
VAC
Hz
rpm
W
A
°C
1~ 115
50/60
1600
32
0,50
-30..+50
1~ 230
50/60
1600
33
0,25
-30..+50
Curve
Nominal data
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST are
applied for
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
Air performance measured
in H2O
Pa
Curves
A
B
without protection against
accidental contact
80
0,40
100
3
1
1600
18
0,25
59
A
2
1600
26
0,37
57
A
3
1600
32
0,50
55
A
4
1600
30
0,44
56
5
1200
7
0,10
52
A
6
1200
11
0,15
50
LpA measured at 1 m distance
A
7
1200
13
0,18
48
to fan axis
A
8
1200
12
0,18
50
The acoustic values given are
B
1
1600
18
0,14
59
only valid under the measur-
B
2
1600
25
0,21
57
B
3
1600
33
0,25
55
B
4
1600
30
0,25
56
B
5
1200
7
0,06
52
B
6
1200
10
0,08
50
have to be checked and re-
B
7
1200
13
0,11
48
viewed once installed or fitted!
B
8
1200
12
0,10
50
0,24
may vary depending on the
60
installation situation.
7
2
0,16
With any deviation to the stan-
40
dard setup, the specific values
20
0,08
6
For detailed information
see page 62 ff.
5
pfs
0
qV
50
100
n max. = 1600 min-1
36
100
150
200
200
300
n = 1200 min-1
250
400
1
300
500
n min. = 600 min-1
cfm
m3/h
LWA
dB(A)
A
ment conditions listed and
8
I
A
LWA as per ISO 13347,
Suction-side noise levels:
0,32
120
0,48
4
Pe
W
A
Installation category A,
0,56
140
as per: ISO 5801,
n
rpm
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
off
on (L1 or N)
n1
n2
Mass of centrifugal
module with support
bracket
S
Speed selection
Centrifugal module
with support bracket
kg
K1G 220-AF90 -02
1,4
K1G 220-AF92 -02
1,4
113
105
°
4x90
28.5°
4
40±5
6
450+20
Ø220
Ø 295
Ø 310
Ø281+1
4x Ø4.3
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
37
Accessories
p. 40 ff.
EC centrifugal module
diagonal, Ø 200
K1G 200
M1G 055-BD
B
subject to alterations
Perm. amb. temp.
A
Max. back pressure
M1G 055-BD
Max.
current draw(1)
K1G 200
Max.
input power(1)
Motor
Speed/rpm(1)
Type
Frequency
Nominal data
– Bearings: Maintenance-free ball bearings
– Motor protection: Via electronics and
TOP
– Electrical connection: Plug-in connection
on motor side
– Protection class: II
– Product conforming to standard: CE
– Approvals: VDE, UL, CSA, GOST are
applied for
– Speed: Using the programming unit, 2
speeds between nmin and nmax can be
programmed.
Nominal voltage
Curve
– Material: Housing: Plastic PA,
fibreglass-reinforced
Blades: Plastic PA,
fibreglass-reinforced
– Number of blades: 7
– Direction of rotation: clockwise, seen on
rotor
– Type of protection: IP 54
– Insulation class: "B"
– Mounting position: Any
– Condensate discharges: None, open rotor
– Mode of operation: Con. operation (S1)
VAC
Hz
rpm
W
A
PA
°C
1~ 115
50/60
2000
31
0,50
120
-30..+50
1~ 230
50/60
2000
35
0,30
120
-30..+50
(1) Nominal data in operating point with maximum load and 115 or 230 VAC
in H2O
Air performance measured
A
B
as per: ISO 5801,
120
without protection against
4
accidental contact
0,4
80
1
2000
27
0,38
63
2
2000
29
0,42
62
A
3
2000
31
0,50
62
A
4
2000
30
0,43
62
5
1500
14
0,22
57
A
6
1500
16
0,24
56
LpA measured at 1 m distance
A
7
1500
17
0,26
55
to fan axis
A
8
1500
16
0,25
55
The acoustic values given are
B
1
2000
31
0,24
63
only valid under the measur-
B
2
2000
33
0,26
62
B
3
2000
35
0,30
62
B
4
2000
35
0,27
62
B
5
1500
16
0,13
57
B
6
1500
19
0,14
56
have to be checked and re-
B
7
1500
20
0,18
55
viewed once installed or fitted!
B
8
1500
18
0,14
55
0,3
may vary depending on the
0,2
installation situation.
7
40
With any deviation to the stan-
2
0,1
dard setup, the specific values
6
20
For detailed information
see page 62 ff.
pfs
0
qV
50
100
n max. = 2000 min-1
38
100
150
200
5
250
200
300
n = 1500 min-1
400
1
300
500
n min. = 700 min-1
cfm
m3/h
LWA
dB(A)
A
ment conditions listed and
60
I
A
A
3
8
Pe
W
LWA as per ISO 13347,
Suction-side noise levels:
100
n
rpm
A
Installation category A,
0,5
Pa
Curves
– Electr. connection:
L1
black
Mains supply
voltage
Energy-saving
motor / fan
(ESM)
blue
N
Speed selection
L1 or N
brown
S
off
on (L1 or N)
n1
n2
Mass of centrifugal
module with support
bracket
S
Speed selection
Centrifugal module
with support bracket
kg
K1G 200-AA95 -02
1,2
K1G 200-AA73 -02
1,2
4xØ5
6
450+20
40±5
4
78.5
Ø236
Ø250
Ø220
4xØ4.3
Connection lead (total length 450 mm) is fitted ex works and can be detached
Other lengths available as accessory.
39
Accessories
p. 40 ff.
Connection leads (ESM)
a
– Design: Cable conforms to UL standards,
sealed plug. Custom-built connection leads
on request.
10
40
31,5
22,5
27,5
6
9,3
Jacketed cable, internal line
(UL Style 2464/1061)
3 x AWG20 (approx. 0.5 mm2)
Brass lead tips
Connection lines for energy-saving motors 115/230 VAC
Part no.
a
10637-4-1040
450
10640-4-1040
600
10638-4-1040
1500
10639-4-1040
2000
subject to alterations
Guard grilles (ESM)
a
b
Guard grille (sucking side) for energy-saving centrifugal modules
Part no.
Size
a
b
19051-2-2929
190
133,0
9,0
22051-2-2929
220
166,0
8,7
subject to alterations
40
– Material: Plastic PA, fibreglass-reinforced
Connection leads (ESM)
a
– Design: Cable conforms to UL standards,
sealed plug. Custom-built connection leads
on request.
10
40
31,5
22,5
27,5
6
9,3
Jacketed cable, internal line
(UL Style 2464/1061)
4 x AWG20 (approx. 0.5 mm2)
Brass lead tips
Connection lines for energy-saving motors 24 VDC
Part no.
a
10710-4-1040
450
10711-4-1040
1500
subject to alterations
Handheld Programmer
– Easy speed programming
– Battery operated
– User-friendly navigation menu
– Protective boot with kickstand
For Energy Saving Motor (ESM) based products
Part no.
CBC 000-AF08-01
subject to alterations
Makes quick work of programming the two ESM selectable operating speeds. Eliminates the need for a personal computer, software, power adapter
and 2nd cable. Good for production line or field service use. Automatic shut-off function for an extended battery life. Mini-USB connector for uploading
software upgrades. Batteries, programming cable and operating manual included.
41
Pressure sensor
for pressure-controlled speed control
Setting range
cut-off
Factory setting
cut-off
Test pressure
Max. operating
pressure
Max. medium
temperature
Perm. amb. temp.
Mass
Part no.
Max. power input
Nominal data
Nominal voltage
– Material: Housing made of PA
Pressure connection made of brass
– Type of protection: IP 65 according to EN 60529 / IEC 529
– Suitable for commonly used refrigerants
( A R134A; B R407C, R404A, R507)
– Easy installation via pressure connection with 7/16”-20 UNF female thread with
Schrader valve opener
– Power supply via10 VDC
– 0-10 VDC control output signal for pressure-dependent speed control of the fan
– Delivered in individual packaging
VDC
mA
bar
bar
bar
bar
°C
°C
g
40100-4-7380
A
10
1
4 to12.5
7.8
30
27
70
-20 to +65
125
40101-4-7380
B
10
1
10 to 21
15.5
36
32
70
-20 to +65
125
subject to alterations
Connecting cable with plug (1.5 m)
not included in scope of delivery.
Part No.: 24010-4-1040
1
4
2
70
(55)
54
1 = Signal 0-10 V
2 = 10 V
4 = GND
15
– Electr. connection:
Connection
Pressure sensor
20
fan
L
39
N
48
AC1
2AT
P
AC2
N
PE
PE1
2
Control voltage
0-10 VDC
+10V
Imax=1.1mA
1
10V/PWM
47k
47k
1μF
4
Hysteresis
GND
Tacho
Proportional
band
1 bar
ZMM47
Cut-off
42
3
1
4
2
680R
Condensation pressure,
bar
Connection lead (Pressure sensor)
45.5±0.5
– Design: Single packed in plastic bag.
1500 ±20
70 ±10
31 ±0.5
28.3 ±0.5
6
Jacketed cable, internal line
(UL Style 2464), 4 x AWG18
Brass lead tips
Connection line for pressure sensor
Part no.
24010-4-1040
a
1500
subject to alterations
43
Guard grilles (ACi)
– Guard grille acc. to DIN EN ISO 13857 (previously EN 294), made of galvanised or nickelplated and passivated steel wire for device fans.
– Additional guard grilles that do not conform to DIN EN ISO 13857 are available on request.
– Our guard grilles are specially designed for use with ebm-papst fans. Their design ensures
maximum safety with minimum effect on the operating noise level. Note that when using
guard grilles from other manufacturers, compliance with safety-related distances will not
always be present.
LZ30
Fan size 119 x 119
Guard grilles
LZ30
Intake side
ACi 4400
LZ30
Outlet side
153,5 ±1
ACi 4400
115 ±1
Fan series
3±0,25
4,3+0,2
Connector cables (ACi)
5+1
– Connector cable with injection-moulded plug in various lengths.
– Strand ends with core-crimping sleeve, core-end sleeve or tin-plated.
L1 (mm)
Leads
Plug
Leads end
Lead colour
Receptacle for tabs
610
0,5 mm2
0,5 mm2
straight
C
black/black
2,8 x 0,5
AC
straight
A
black/black
2,8 x 0,5
AC
0,5 mm2
0,5 mm2
straight
B
black/black
2,8 x 0,5
AC
straight
A
black/black
2,8 x 0,5
AC
0,5 mm2
0,5 mm2
straight
C
black/black
2,8 x 0,5
AC
straight
B
black/black
2,8 x 0,5
AC
0,82 mm2
straight
C
black/black
2,8 x 0,5
AC
LZ120
LZ120-4
2 000
LZ120-16
800
LZ120-18
4 000
LZ126
1 000
LZ127
1 600
LZ130-1
610
Leads end A
Tin-plated
Leads end B
Core end sleeve
6
44
10+5
–2
Application
Leads end C
ȯ1,5
Core crimp sleeve
ȯ1,5
Plug model
6
Fan filter guard drilles (ACi)
– Filter guard grille consisting of 3 parts: outer grille barrier, inner fastening plate and replaceable filter mat.
– Grille barrier made of moulded polycarbonate (PC), with matted surface.
– Fast and easy exchange of filter mat via a quick release on the grille barrier.
– Fastening plate made of wire netting, with black powder coating.
– Filter mat can be replaced while the fan is running, protection provided by welded wire
netting.
– Filter mat made of white, synthetically bonded fibres.
Protection filter
Fan size
FF119
119 x 119 mm
A
B
C
162
136
18,5
D
104,5
Replacement filter*
RF 119
* Replacement filters only in packs of 5.
FF 119
Fan size:
119 x 119 mm
Filter capacity
A fan filter guard filters out up to 75% of
dust particles up to a size of 5-10 microns
and withstands temperatures of up to
100°C. Flame retardant in accordance with
DIN 53438, grade F1. For installed, clean
filters, an air flow reduction of 20 – 30%
can be assumed.
45
Electrical connections
W1G 200 - EF41 - 01 / W1G 200 - EF01 - 01
Customer circuit
Full
speed
Connection
Speed setting with
fixed resistance
Speed
setting
1
4
Fan / Motor
UN +24 VDC
1
UB
1
4.7K
1-10V
4
2
10V -> n = max
1V -> n = min
< 1V -> n = 0
Safe start up at Unom -30%
from 40% PWM
PWM/0-10 VDC
4
4
RE>100K
10K
2
Tacho
3
680 R
47 V
Speed
setting via
PWM 1-10kHz
GND
Setting of values via
ebm temperature
controller
GND1
2
Reverse-polarity
protection
1
P
1
33K
4
OUT
4
N
12V
T
2
2
100% PWM -> n = max
10% PWM -> n = min
< 10% PWM -> n = 0
Safe start-up at Unom -30%
from 40% PWM
Line
No.
Connection
Colour
Assignment / function
1
1
Un +24 VDC
red
Power supply 24 VDC, residual ripple 3.5 %, see type plate for voltage range
1
2
GND
blue
Reference ground
1
3
Tacho
white
Tacho output: Open Collector, 1 pulse per revolution, Isink max = 10 mA
1
4
PWM / 0-10 VDC yellow
46
Tacho
Control input PWM or 0-10 V, RE > 100K
Electrical connections
W1G 200 - EC87 - A2 / W1G 200 - EC91 - A4
Customer circuit
Connection
Fan / Motor
CON10
max.
speed
Adjustable
speed
L
1
50.1
1.25A
50.3
AC1
P
AC2
N
N
1-10V
2
50.3
50.4
10V -> n = max
1V -> n = min
< 1V -> n = 0
CON50
+10V
1
Imax=1.1mA
10V/PWM
3
47k
Speed
setting via
PWM 1-10kHz
Speed
setting via
potentiometer
47k
100μF
GND
4
15V
Tacho
50.1
1
2
680R
2
Imax=10mA
ZMM47
50.3
50.3
10K
12V
50.4
50.4
100% PWM -> n = max
10% PWM -> n = min
< 10% PWM -> n = 0
Line
No.
Connection
Colour
Assignment / function
CON10
1
L
black
Power supply 230 VAC, 50 - 60 Hz, see type plate for voltage range
CON10
2
N
blue
Neutral conductor
CON50
1
10V/max.1.1mA
red
Voltage output 10V / 1.1mA, electrically isolated
CON50
2
Tacho
white
Tacho output: Open Collector, 1 pulse per revolution, electrically isolated
CON50
3
0-10V PWM
yellow
Control input 0 - 10 V or PWM, electrically isolated
CON50
4
GND
blue
GND - Connection for control interface
47
The smart way to save energy
Classic shaded-pole motors (Q motors) have reached the end of their usefulness. The new iQ motors
are just as compact, but they are significantly more intelligent, energy-saving and environmentally
friendly. Thanks to ebm-papst GreenTech EC technology, the efficiency has been increased by some
70 %. This means that the switch pays off extremely quickly. And that’s not all: With the additional
functions of the latest iQ² generation, you can increase the efficiency even more with intelligent control
options.
Exchange your old motor for 70 % more efficiency
From the outside, the iQ and iQ² motors are barely distinguishable from conventional shaded-pole
motors. Thus the identical dimensions enable easy replacement without structural modifications or
other obstacles. Axial impellers with diameters from 154 to 300 mm can be installed on the iQ
motor as usual. The same applies to the mounting flange, the wall ring and the guard grille. Thus
the efficiency of many applications can be increased drastically without any development effort.
One design – thousands of applications
Just one design is compatible with the entire range of impellers, from 154 to 300 mm. This makes
logistics easier and keeps your development effort low. Moreover, the smallest size, the iQ 3608, is the
most compact version of an EC motor in the area of refrigeration technology. With an axial installation
depth of only 74 mm, it guarantees the bit of air that is so badly needed in tight spaces.
Energy-saving and quiet – throughout its long service
What all variants have in common is their low-noise performance and very long service life. A critical
role is played by a particularly low-friction bearing system with ball bearings. This enables the
iQ motors to continue to deliver their enormous savings potential for a very long time.
All advantages at a glance
– High efficiency of up to 70 %
– Constant speed, even in the event of voltage fluctuations
– High running smoothness due to low-friction bearing system
– Intelligent electronics with n-control, overload and locked-rotor protection
– Conventional AC technology can be replaced easily
– Identical accessories and dimensions to Q motor
– Long service life due to maintenance-free ball bearings
– One solution replaces multiple sizes of comparable AC motors
– Available in 24 V, 115 V and 230 V
48
The new generation of iQ motors
Quadratic. Practical. Intelligent.
Savings potential
51
Technical data
52
Air performance curves
56
49
The smart square:
The new additional functions of the iQ²
The new iQ² motors can do everything the “normal” iQ motors can do – and more, which makes applications such as those in refrigeration technology more efficient. Additional functions enable different
operating modes, like one that is customised to your needs or automated reverse operation. Simply
select the motor variant that best suits your application.
iQ² safety class II.
iQ² reverse on start.
iQ² reverse on demand.
iQ² two speeds.
The iQ² safety class II features a
The iQ² reverse on start runs back-
With the iQ² reverse on demand,
The special performance feature of
special design with plastic housing
wards automatically for a pre-pro-
you determine the time and
the iQ² two speeds is its two factory-
parts. This makes extra steps such
grammed time at each start-up.
duration of the reverse operation.
programmed speed steps. For ex-
as installing the protective earth
This is an important function for
For example, you can use the
ample, if you want your application
conductor (protection class II)
cooling units, as it allows accumu-
defrost cycle of the evaporator
to run in different daytime and
unnecessary – and saves you a lot
lated dust to be blown from the heat
to eliminate dust from the heat
nighttime modes to save additional
of money.
exchanger of the condenser – for
exchanger of the condenser.
energy, it is the right choice.
long-lasting high cooling capacity.
General overview of data: iQ and iQ²
Material:
Die-cast aluminium housing
Protection class:
I, for iQ² plastic housing II on request
Direction of air flow:
Sucking or blowing
Approvals:
UL, TÜV in accordance with DIN EN
Direction of rotation:
(depending on axial impeller used)
60335-2-24, DIN EN 60335-2-89,
Counterclockwise, seen on shaft end
DIN EN 60075-15, in progress for iQ²
System of protection:
IP54
Insulation class:
"H"
Mounting position:
Any
Mode of operation:
Continuous operation (S1)
Bearings:
Maintenance-free ball bearings
and M4 screw is used to secure the
Motor protection:
Via electronics
impeller on the motor shaft
Electrical connection: Mains cable
50
Mounting attachment parts: Guard grille and wall ring are attached
to the projecting thread ends on
the A side
Axial impeller attachment:
A plastic adapter with catching peg
iQ – Intelligence that pays
A quick example calculation:
A typical supermarket operates 200 AC fans with 200 mm blades (blade angle 28°) in its refrigeration units. If the shaded-pole motors were to be
replaced by iQ or iQ² motors, the energy consumption would be reduced by 39 megawatt hours. That is an annual saving of more than 5.000 euros*
and a good 23 tonnes of CO2.
Reduction in
Annual reduction
Annual reduction
Annual reduction
power input:
in energy consumption:
in energy costs:
in emissions:
70 %
39 MWh
≈ 5.000 euro total
23 tonnes CO2
*Assumptions: electricity price 0.13 euros per kWh, continuous operation 24 hours a day, 365 days a year
If you look at the figures for the iQ-motor over a prolonged period, its considerable energy-savings potential becomes especially obvious.
350
Electricity price: 0.13 euro per kWh
300
Consumption [MWh]
Number of motors: 200
250
Savings
potential
Continuous operation (24 h/365 d)
200
≈138 t CO2
Axial blades: 200 mm /28° blade angle
150
≈30.600 euro
CO2 emissions factor: 0.596 kg per kWh
100
(Federal Environment Agency, Dessau, May 2008)
iQ 3612
AC-shaded-pole motor
(comparable)
50
0
0
1
2
3
4
5
6
Service life [years]
iQ motor in energy-saving calculator:
How much energy and money could an iQ motor
save in your company? By what amount could
you decrease CO2 emissions in the process?
You can get a good idea of this with the ebmpapst energy savings calculator at www.greentech.info. Go for your energy cost calculation
there and the numbers will speak for themselves!
51
iQ/iQ2 3608
Hybrid
Standard, ROS, ROD, 2 Speeds
Hybrid
iQ/iQ2 3612
24 V
Standard, ROS, ROD, 2 Speeds
Hybrid
iQ/iQ2 3620
24 V
Perm. amb. temp.
Mass
Standard, ROS, ROD, 2 Speeds
Output power
Features
Speed/rpm
Type
Frequency
Nominal data
Nominal voltage
Technical data
V
Hz
rpm
W
°C
kg
220-240
50/60
1300
5
-40..+50
0,5
115*
50/60
1550
5
-40..+50
0,5
220-240
50/60
1300
5
-40..+50
0,4
115*
50/60
1550
5
-40..+50
0,4
220-240
50/60
1300
15
-40..+50
0,6
115*
50/60
1550
15
-40..+50
0,6
220-240
50/60
1300
15
-40..+50
0,5
115*
50/60
1550
15
-40..+50
0,5
24
--
24
--
1300
400-1300
11
-40..+50
0,6
11
-40..+50
0,6
220-240
50/60
1300
20
-40..+50
0,8
115*
50/60
1550
20
-40..+50
0,8
220-240
50/60
1300
20
-40..+50
0,7
115*
50/60
1550
20
-40..+50
0,7
24
--
15,5
-40..+50
0,8
24
--
15,5
-40..+50
0,8
1300
400-1300
Dimensions
a
b
74
43,5
30,5
82
43,5
30,5
90
51,5
38,5
*With 2 Speeds: upper speed
subject to alterations
A-side
83
67
Ø41
a
c
15
4x)
(
M4
11,5
480 / 1000 / 1500
51
Ø3,6
Ø25,4
Standard version
M4
26
b
B-side
Standard direction
of rotation
52
A-side
c
Multi function version
(only iQ 3612)
A-side
B-side
82
83
67
Ø41
18
48,9
M4 (3x)
30,5
Depth of screw
max. 5 mm
M4
51
48
Ø3,6
Ø25,4
3x
12
0°
13
15
1500
11,5
)
(4x
4
M
26
Ø41
Ø71,4
M4
B-side
A-side
43,4
Standard direction
of rotation
24 V version; 400 - 1300 rpm; 0-10 V interface
Speed vs. control voltage:
1200
1000
Speed [rpm]
800
600
400
200
0
0
1
2
3
4
5
6
7
8
9
Control voltage [V]
53
Axial impeller
p. 58
Mounting bracket
p. 59
Guard grille
p. 60
Basket guard grille
p. 60
Wall ring
p. 61
iQ/iQ2-motor – combination with axial impellers
Axial impeller
blade angle
Input power
running at full throttle
Input power
running at free air
Air flow running
at free air
at n=1300 rpm
iQ/iQ2 3608
mm
°
W
W
m3/h
154
22
3,0
2,0
170
154
28
3,8
2,8
190
154
34
4,1
3,3
220
172
22
4,6
2,6
230
172
28
6,1
3,8
270
172
34
7,8
5,0
310
200
22
9,2
4,5
360
Curves
Motor
Axial impeller
diameter
Power input and air flow
A
B
C
iQ/iQ2 3612
200
28
9,2
5,5
410
mm
°
W
W
m3/h
172
28
4,2
2,9
270
172
34
5,7
3,8
310
200
22
5,1
3,4
360
200
28
8,3
5,3
410
200
34
12,1
7,3
470
230
22
9,6
6,0
520
230
28
19,0
13,1
710
230
34
20,5
16,9
750
254
22
21,2
11,3
710
19,3
21,2
980
W
W
m3/h
16,1
8,3
520
21,2
11,9
710
25,0
13,9
750
26,5
12,3
710
27,4
23,1
980
25,7
28,4
1010
23,7
24,3
1380
B
iQ/iQ2 3620
subject to alterations
254 *
28
mm
°
230
22
230
28
230
34
254
22
254
28
254 *
34
300 *
22
D
E
F
E
G
H
* Depending on back pressure, full nominal speed of 1300 min-1 is not reached to some part. Depending on mounting situation and version, a speed of approx. 1200 min-1 (+/- 100 min-1) is reached. Due to the
intelligent electronics, however, safe (permanent) operation is still guaranteed.
Power ratings (220 - 240 V design):
Power input and air flow at 230 V / 50 Hz and a constant speed of 1300 min-1.
54
Axial impeller
p. 58
Mounting bracket
p. 59
Guard grille
p. 60
Basket guard grille
p. 60
Wall ring
p. 61
55
iQ/iQ2-motor
Air performance curves measured in wall ring, at a constant speed of 1,300 rpm.
A
Pa
iQ/iQ2 3608 / 3612, Ø 172
Pa
iQ/iQ2 3608, Ø 154
B
90
50
80
70
40
60
50
30
40
20
30
20
10
pfs
pfs
10
50
22°
100
28°
150
200
250
qV
m3/h
34°
50
100
22°
200
250
300
m3/h
34°
iQ/iQ2 3612, Ø 200
Pa
iQ/iQ2 3608, Ø 200
150
28°
C
Pa
qV
D
70
50
60
50
40
40
30
30
20
20
10
pfs
pfs
10
qV
50
22°
56
100
28°
150
200
250
300
350
m3/h
qV
100
22°
200
28°
300
34°
400
m3/h
E
Pa
iQ/iQ2 3612, Ø 254
Pa
iQ/iQ2 3612 / 3620, Ø 230
F
100
80
70
80
60
50
60
40
40
30
20
20
pfs
pfs
10
100
200
22°
28°
300
400
500
600
700
qV
m3/h
200
22°
34°
600
800
m3/h
iQ/iQ2 3620, Ø 300
Pa
iQ/iQ2 3620, Ø 254
400
28°
G
Pa
qV
100
80
80
60
60
40
40
20
20
pfs
pfs
100
H
qV
200
22°
400
28°
34°
600
800
m3/h
qV
200
400
600
800
1000
1200
m3/h
22°
57
Axial impellers
b
b
❮ "V"
"A" ❯
– Material: Sheet aluminium
a
c
6,6
❮ Direction of rotation
c
4 x Ø 4.0 with pitch circle for holes Ø 25.4 mm
Axial impellers
Part no. for dir. of air flow "V"
Part no. for dir. of air flow "A"
Blade angle α
27453.34001
27453.34201
27453.34002
27453.34202
27453.34003
a
b
c
22° ± 1°30’
154,0
27,5
14,0
28° ± 1°30’
154,0
32,0
16,0
27453.34203
34° ± 1°30’
154,0
37,0
18,0
27453.34004
27453.34204
22° ± 1°30’
172,0
31,0
14,5
27453.34005
27453.34205
28° ± 1°30’
172,0
36,0
17,0
27453.34006
27453.34206
34° ± 1°30’
172,0
42,0
21,0
27453.34007
27453.34207
22° ± 1°30’
200,0
32,0
15,5
27453.34008
27453.34208
28° ± 1°30’
200,0
37,5
18,0
27453.34009
27453.34209
34° ± 1°30’
200,0
45,0
22,0
27453.34010
27453.34210
22° ± 1°30’
230,0
35,0
17,5
27453.34011
27453.34211
28° ± 1°30’
230,0
43,0
21,5
27453.34012
27453.34212
34° ± 1°30’
230,0
50,0
24,0
27453.34013
27453.34213
22° ± 1°30’
254,0
37,0
19,0
27453.34014
27453.34214
28° ± 1°30’
254,0
45,0
23,5
27453.34015
27453.34215
34° ± 1°30’
254,0
52,0
26,0
27453.34016
27453.34216
22° ± 1°30’
300,0
43,0
21,5
27453.34017
27453.34217
28° ± 1°30’
300,0
53,5
26,5
27453.34018
27453.34218
34° ± 1°30’
300,0
61,0
30,0
subject to alterations
58
Mounting bracket
b
b
2,5
18
18
26
18
18
40
16
25
25
4,3
14
8
4,3
14
4,2
24
c
d
8,2
c
d
– Material: Sheet steel, galvanized and blue
chromated
10
9°
6,2
2,5
8,2
Vers. 3
a
Vers. 2
a
Vers. 1
5
16,2
Mounting bracket - foot measure 18 mm (multi-function design)
Part no.
Size
Vers.
a
b
c
d
27452.71002
172
1
56,0
51,0
78,0
100,0
27452.71005
200
1
67,0
51,0
78,0
100,0
27452.71003
230
1
74,5
51,0
78,0
100,0
27452.71004
254
2
85,5
27452.71001
300
3
112,0
51,0
—
78,0
100,0
150,0
172,0
subject to alterations
51
51
51
1,5
4,3
13
31,8
50,3
8,2
8
21
40
8,2
26
24
8,2
78
100
26
7
78
100
26
14
2,5
2,5
2,5
78
100
– Material: Sheet steel, galvanized and blue
chromated
a
Vers. 3
a
Vers. 2
a
Vers. 1
4,3
14
14
4,3
Mounting bracket - foot measure 26 mm (standard design or multi-function design)
Part no.
Size
Vers.
a
27452.71201
154
1
39,0
27452.71202
172
1
52,0
200
1
72,0
230
1
72,0
27452.71204
254
1
84,0
27452.71205
254
2
84,0
27452.71206
300
2
109,0
27452.71207
300
3
109,0
27452.71203
subject to alterations
59
Guard grille
– Material: Steel, galvanized and blue
chromated
b
Øa
94,5
2,7
c
5
Guard grille
Part no.
Size
Max. blade angle α at "V"
Max. blade angle α at "A"
27452.70002
154
34°
27452.70003
172
34°
27452.70004
200
27452.70005
27452.70006
27452.70007
a
b
c
34°
170,0
190,0
11,5
34°
188,0
208,0
11,5
34°
28°
214,0
236,0
11,5
230
28°
28°
246,0
266,0
17,5
254
28°
28°
270,0
290,0
17,5
300
—
22°
324,0
344,0
17,5
subject to alterations
2,7
– Material: Steel, galvanized and blue
chromated
Øa
Øb
94,5
c
92
5
Basket guard grille
Part no.
Size
Max. blade angle α at "V"
Max. blade angle α at "A"
27452.70201
172
34°
27452.70202
200
34°
27452.70203
230
27452.70204
254
27452.70205
300
subject to alterations
60
a
b
c
34°
188,0
208,0
37,5
28°
212,0
236,0
37,5
28°
28°
246,0
266,0
40,0
28°
28°
270,0
290,0
40,0
—
22°
324,0
344,0
46,8
Wall rings
d
Øa
67
67
– Material: Sheet steel, coated in grey plastic
❮ "V"
R3
,5
b
4,3
2
4,3
1
48
c
Wall rings, direction of air flow "V"
Part no. (sheet steel)
Part no. (plastic)
Size
Max. blade angle α
27452.70501
27452.70802
154
27452.70502
27452.70803
172
27452.70503
27452.70804
27452.70504
27452.70505
27452.70506
27452.70806
a
b
c
d
d (plastic)
34°
164,0
190,0
200,0
24,0
26,0
34°
182,0
208,0
223,0
24,0
26,0
200
34°
210,0
236,0
246,0
24,0
26,0
---
230
28°
240,0
266,0
276,0
24,0
---
27452.70805
254
28°
264,0
290,0
300,0
24,0
26,0
300
22°
308,0
344,0
356,0
24,0
26,0
subject to alterations
36
– Material: Sheet steel, coated in grey plastic
,5
R4
67
67
1
d
b
2
"A" ❯
Øa
4,3
4,3
c
Wall rings, direction of air flow "A"
Part no. (sheet steel)
Part no. (plastic)
Size
Max. blade angle α
a
b
c
d
d (plastic)
27452.70701
---
154
34°
162,0
190,0
200,0
24,0
---
27452.70702
---
172
34°
180,0
208,0
223,0
24,0
---
27452.70703
---
200
28°
208,0
236,0
246,0
24,0
---
27452.70704
---
230
28°
238,0
266,0
276,0
24,0
---
27452.70705
27452.70807
254
28°
262,0
290,0
300,0
24,0
26,0
27452.70706
---
300
22°
308,0
344,0
356,0
24,0
---
subject to alterations
61
Technical parameters & scope
High standards for all ebm-papst products
Here at ebm-papst, we constantly strive to further improve our products in order to be able to offer you the best
possible product for your application. Careful monitoring of the market ensures that technical innovations are
reflected in the improvements of our products.
Based on the technical parameters listed below and the ambience you want our product to operate in,
we here at ebm-papst can always work out the best solution for your specific application.
General performance parameters
Service life
Any deviations from the technical data and parameters described here
The service life of ebm-papst products depends on two major factors:
are listed on the product-specific data sheet.
– The service life of the insulation system
Type of protection
The service life of the insulation system mainly depends on voltage level,
The type of protection is specified in the product-specific data sheets.
temperature and ambient conditions, such as humidity and condensation.
– The service life of the bearing system
The service life of the bearing system depends mainly on the thermal load
Insulation class
on the bearing.
The insulation class is specified in the product-specific data sheets.
The majority of our products use maintenance-free ball bearings for
any mounting position possible. As an option, sleeve bearings can be
Mounting position
used, which is indicated on the product-specific data sheet wherever
The mounting position is specified in the product-specific data sheets.
applicable.
The service life L10 of the ball bearings can be taken as approx. 40,000
Condensate discharge holes
operating hours at an ambient temperature of 40 °C, yet this estimate
Information on the condensate discharge holes is provided in the
can vary according to the actual ambient conditions.
product-specific data sheets.
We will gladly provide you with a lifetime calculation taking into account
your specific operating conditions.
Mode of operation
The mode of operation is specified in the product-specific data sheets.
Motor protection / thermal protection
Information on motor protection and thermal protection is provided in the
Protection class
product-specific data sheets.
The protection class is specified in the product-specific data sheets.
Depending on motor type and field of application, the following protective
features are realised:
– Thermal overload protection (TOP), either in-circuit or external
– PTC with electronic diagnostics
– Impedance protection
– Thermal overload protection (TOP) with electronic diagnostics
– Current limitation via electronics
If an external TOP is connected, the customer has to make sure to
connect a conventional trigger device for switching it off.
Products without fitted TOP and without protection against improper use,
a motor protection complying with the valid standards has to be installed.
62
Left: Endurance test room
Middle: Shock test
Right: Chamber test rig
Mechanical strain / performance parameters
Legal and normative directives
All ebm-papst products are subjected to comprehensive tests complying
The products described in this catalogue are designed, developed and
with the normative specifications. In addition to this, the tests also reflect
produced in keeping with the standards in place for the relevant product
the vast experience and expertise of ebm-papst.
and, if known, the conditions governing the relevant fields of application.
Vibration test
Standards
Vibration tests are carried out in compliance with
Information on standards is provided in the product-specific data sheets.
– Vibration test in operation according to DIN IEC 68, parts 2-6
– Vibration test at standstill according to DIN IEC 68, parts 2-6
EMC
Information on EMC standards is provided in the product-specific data
Shock load
sheets.
Shock load tests are carried out in compliance with
Complying with the EMC standards has to be established on the final
– Shock load according to DIN IEC 68, parts 2-27
appliance, as different mounting situations can result in changed EMC
properties.
Balancing quality
Testing the balancing quality is carried out in compliance with
Leakage current
– Residual imbalance according to DIN ISO 1940
Information on the leakage current is provided in the product-specific
– Standard balancing quality level G 6.3
data sheets.
Should you require a higher balancing quality level for your specific
Measuring is according to IEC 60990.
application, please let us know and specify this when ordering your
product.
Approvals
In case you require a specific approval for your ebm-papst product
Chemo-physical strain / performance parameters
(VDE, UL, GOST, CCC, CSA, etc.) please let us know.
Should you have questions about chemo-physical strain, please direct
Most of our products can be supplied with the relevant approval.
them to your ebm-papst contact.
Information on existing approvals is provided in the product-specific
data sheets.
Fields of application, industries and applications
Our products are used in various industries and applications:
Air performance measurements
Ventilation, air-conditioning and refrigeration technology, clean room
All air performance measurements are carried out on suction side and on
technology, automotive and rail technology, medical and laboratory tech-
chamber test beds conforming to the specifications as per ISO 5801 and
nology, electronics, computer and office technology, telecommunications,
DIN 24163. The fans under test are installed in the measuring chamber at
household appliances, heating, machines and plants, drive engineering.
free air intake and exhaust (installation category A) and are operated at
Our products are not designed for use in the aviation and aerospace
nominal voltage, with AC also at nominal frequency, and without any
industry!
additional components such as guard grilles.
As required by the standard, the air performance curves correspond to
an air density of 1.2 kg/m3.
63
Room for precision noise measuring
Measurement conditions for air and noise measurement
ebm-papst products are measured under the following conditions:
– Axial and diagonal fans in direction of rotation “V” in full nozzle and
without guard grille
– Backward curved centrifugal fans, free-running and with inlet nozzle
– Forward curved single and dual inlet centrifugal fans with housing
Noise measurements
All noise measurements are carried out in low-reflective test rooms with
reverberant floor. Thus the ebm-papst acoustic test chambers meet the
requirements of precision class 1 according to DIN EN ISO 3745. For noise
measurement, the fans being tested are placed in a reverberant wall and
operated at nominal voltage (for AC, also at nominal frequency) without
additional attachments such as the guard grille.
Sound pressure level and sound level
All acoustic values are established according to ISO 13347, DIN 45635
and ISO 3744/3745 to accuracy class 2 and given in A-rated form.
When the sound pressure level (Lp) is measured, the microphone is on
the intake side of the fan being tested, usually at a distance of 1 m on
the fan axis.
To measure the sound power level (Lw), 10 microphones are distributed
over an enveloping surface on the intake side of the fan being tested
(see graphic). The sound power level measured can be roughly calculated
1,5d
from the sound pressure level by adding 7 dB.
D
Measuring configuration as per ISO 13347-3 respectively DIN 45635-38:
10 measuring points
d≥D
h = 1,5d ... 4,5d
h
3d
Measurement area S = 6d2 + 7d (h + 1,5d)
2d
64
pressure level of a fan is approximately 75 dB(A). The level increase measured from the diagram is 9 dB. Thus the overall sound level of the installation can be expected to be 84 dB(A).
15
10
9
Example: 8 A3G800 axial fans are on a condenser. According to the data sheet, the sound
5
the noise values specified in the data sheet. This is shown in the diagram opposite.
0
The noise characteristics of multiple identical fans can be determined in advance based on
[dB]
[dB(A)]
Adding 2 noise sources with the same level results in a level increase of approx. 3 dB.
Increase in sound pressure / sound power level
Combined level of multiple same-level sound sources
1
2
3
4
5
6 7 8 9 10
15
20 25
ating point and an axial fan A3G710 with 71 dB(A) in a ventilation unit. The level difference is
4 dB. The level increase can now be read in the diagram as approx. 1.5 dB. This means that
the overall sound level of the unit can be expected to be 76.5 dB(A).
3
2
1,5
Example: There is an axial fan A3G800 with a sound pressure level of 75 dB(A) at the oper-
1
levels given in the data sheet. This is shown in the diagram opposite.
0
The acoustic performance of two different fans can be predetermined based on the sound
Increase in sound pressure / sound power level
Combined level of two different-level sound sources
[dB]
[dB(A)]
Number of sources of sound with identical level
0
4
8
12
16
20
Sound power level is independent of distance to the sound source. In contrast to this, sound
-10
pressure level decreases the further away the noise source is. The adjacent diagram shows
0
[dB]
[dB(A)]
Distance laws
24
[dB]
[dB(A)]
Difference in level with two sources of sound
the decrease in level under far sound field conditions. Far sound field conditions apply when-
decreases by 6 dB. In the near field of the fan, other correlations apply and the decrease in
levels can be considerably smaller. The following example only applies to far sound field
conditions and can vary strongly depending on the installation effects:
With an axial fan A3G300, a sound pressure level of 65 dB(A) was measured at a distance of
1 m. According to the adjacent diagram, at a distance of 20 m we would get a reduction by
-20
-26
-30
vant literature on this complex topic. Per doubling of distance, the level in the far sound field
-40
wavelength to be considered. For more information on far sound field, please consult the rele-
Decrease in sound pressure level
ever the distance between microphone and fan is big when compared to fan diameter and
1
Distance
2
5
10
20
50
100
[m]
26 dB, i.e. a sound pressure level of 39 dB(A).
65
fan agent
compact fan agent
ebm-papst in Germany
motor specialist
motor agent
Germany
ebm-papst
Mulfingen GmbH & Co. KG
ebm-papst
St. Georgen GmbH & Co. KG
ebm-papst
Landshut GmbH
Bachmühle 2
D-74673 Mulfingen
Phone +49 7938 81-0
Fax +49 7938 81-110
[email protected]
Hermann-Papst-Straße 1
D-78112 St. Georgen
Phone +49 7724 81-0
Fax +49 7724 81-1309
[email protected]
Hofmark-Aich-Straße 25
D-84030 Landshut
Phone +49 871 707-0
Fax +49 871 707-465
[email protected]
www.ebmpapst.com
www.ebmpapst.com
www.ebmpapst.com
66
Berlin
Dipl.-Ing. (TH) Jens Duchow
Händelstraße 7
D-16341 Panketal
Phone +49 30 944149-62
Fax +49 30 944149-63
[email protected]
Heilbronn / Heidelberg
Dipl.-Ing. Mark Gartner
Gehrweg 12
D-74199 Unterheinriet
Phone +49 7130 404569-1
Fax +49 7130 404569-2
[email protected]
Bielefeld
Dipl.-Ing. (FH) Wolf-Jürgen Weber
Niehausweg 13
D-33739 Bielefeld
Phone +49 5206 91732-31
Fax +49 5206 91732-35
[email protected]
Kassel
Dipl.-Ing. (FH) Ralph Brück
Hoherainstraße 3 b
D-35075 Gladenbach
Phone +49 6462 4071-10
Fax +49 6462 4071-11
[email protected]
Dortmund
Dipl.-Ing. (FH) Hans-Joachim Pundt
Auf den Steinern 3
D-59519 Möhnesee-Völlinghausen
Phone +49 2925 800-407
Fax +49 2925 800-408
[email protected]
Koblenz
Winfried Schaefer
Hinter der Kirch 10
D-56767 Uersfeld
Phone +49 2657 16-96
Fax +49 2657 16-76
[email protected]
Frankfurt
Dipl.-Ing. Christian Kleffmann
Dr.-Hermann-Krause-Straße 23
D-63452 Hanau
Phone +49 6181 1898-12
Fax +49 6181 1898-13
[email protected]
Munich
Dipl.-Wirt.-Ing. (FH) Jens Peter
Landsbergerstraße 14
D-86932 Pürgen
Phone +49 8196 99877-54
Fax +49 8196 99877-55
[email protected]
Halle
Dipl.-Ing. (TU) Michael Hanning
Lercheneck 4
D-06198 Salzatal / OT Lieskau
Phone +49 345 55124-56
Fax +49 345 55124-57
[email protected]
Nuremberg
Dipl.-Wirt.-Ing. (FH) Axel Resch
Dr.-August-Koch-Str. 1
D-91639 Wolframs-Eschenbach
Phone +49 9875 9783-170
Fax +49 9875 9783-171
[email protected]
Hamburg
Ingenieurbüro Breuell GmbH
Ing. Dirk Kahl
Elektroingenieur
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-19
Fax +49 40 538092-84
[email protected]
Offenburg
Dipl.-Ing. (FH) Ralf Braun
Hubeneck 21
D-77704 Oberkirch
Phone +49 7802 9822-52
Fax +49 7802 9822-53
[email protected]
Stuttgart
Dipl.-Ing. (FH) Rudi Weinmann
Hindenburgstraße 100/1
D-73207 Plochingen
Phone +49 7153 9289-80
Fax +49 7153 9289-81
[email protected]
Ulm
M.Sc. Reinhard Sommerreißer
Am Silbermannpark 10
D-86161 Augsburg
Phone +49 821 6610-7023
Fax +49 821 6610-7024
[email protected]
Distributors
Frankfurt
R.E.D. Handelsgesellschaft mbH
Gutenbergstraße 3
D-63110 Rodgau - Jügesheim
Phone +49 6106 841-0
Fax +49 6106 841-111
[email protected]
www.red-elektromechanik.de
Hamburg
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
Munich
A. Schweiger GmbH
Ohmstraße 1
D-82054 Sauerlach
Phone +49 8104 897-0
Fax +49 8104 897-90
[email protected]
www.schweiger-gmbh.com
(1 to 5 pieces)
North
Breuell + Hilgenfeldt GmbH
Grützmühlenweg 48
D-22339 Hamburg
Phone +49 40 538092-20
Fax +49 40 538092-84
[email protected]
South
HDS Ventilatoren Vertriebs GmbH
Glaswiesenstraße 1
D-74677 Dörzbach
Phone +49 7937 80355-20
Fax +49 7937 80355-25
[email protected]
www.hds-gmbh.net
ebm-papst in Europe
Europe
Austria
ebm-papst Motoren & Ventilatoren GmbH
Straubingstraße 17
A-4030 Linz
Phone +43 732 321150-0
Fax +43 732 321150-20
[email protected]
www.ebmpapst.at
Belarus
ebm-papst Bel AgmbH
P.O. Box 117
BY-220138 Minsk
Phone +375 17 3851556
Fax +375 17 3851556
[email protected]
www.ebmpapst.by
Belgium
ebm-papst Benelux B.V.
Sales office Belgium-Luxemburg
Romeinsestraat 6/0101
Research Park Haasrode
B-3001 Heverlee-Leuven
Phone +32 16 396-200
Fax +32 16 396-220
[email protected]
www.ebmpapst.be
Bulgaria
ebm-papst Romania S.R.L.
Str. Tarnavei No. 20
RO-500327 Brasov
Phone +40 268 331859
Fax +40 268 312805
[email protected]
Croatia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Czech Republic / Slovakia
ebm-papst CZ s.r.o.
Kaštanová 34a
CZ-620 00 Brno
Phone +420 544 502-411
Fax +420 547 232-622
[email protected]
www.ebmpapst.cz
Denmark
ebm-papst Denmark ApS
Vallensbækvej 21
DK-2605 Brøndby
Phone +45 43 631111
Fax +45 43 630505
[email protected]
www.ebmpapst.dk
Estonia
ebm-papst Oy, Eesti Filiaal
Kesk tee 13
Aaviku küla, Jüri Tehnopark
EST-75301 Rae Vald, Harjumaa
Phone +372 65569-78
Fax +372 65569-79
www.ebmpapst.ee
Finland
ebm-papst Oy
Puistotie 1
FIN-02760 Espoo
Phone +358 9 887022-0
Fax +358 9 887022-13
[email protected]
www.ebmpapst.fi
France
ebm-papst sarl
ZI Nord - rue A. Mohler
BP 62
F-67212 Obernai Cedex
Phone +33 820 326266
Fax +33 3 88673883
[email protected]
www.ebmpapst.fr
Greece
Helcoma
Th. Rotas & Co OE
Davaki 65
GR-17672 Kallithea-Attiki
Phone +30 210 9513-705
Fax +30 210 9513-490
[email protected]
www.helcoma.gr
Hungary
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Iceland
RJ Engineers
Stangarhyl 1a
IS-110 Reykjavik
Phone +354 567 8030
Fax +354 567 8015
[email protected]
www.rj.is
Ireland
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
AuBren Limited
Portlaoise Business & Technology Park
Mountrath Road
IRL-Portlaoise, Co. Laois
Phone +353 57 8664343
Fax +353 57 8664346
[email protected]
www.aubren.com
Italy
ebm-papst Srl
Via Cornaggia 108
I-22076 Mozzate (Co)
Phone +39 0331 836201
Fax +39 0331 821510
[email protected]
www.ebmpapst.it
Macedonia
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
67
fan agent
compact fan agent
ebm-papst in Europe
motor specialist
motor agent
Netherlands
ebm-papst Benelux B.V.
Engelseweg 127
NL-5705 AC Helmond
Phone +31 492 502-900
Fax +31 492 502-950
[email protected]
www.ebmpapst.nl
Russia
ebm-papst Ural GmbH
Posadskaja-Strasse, 23(E), 3
RU-620102 Ekaterinburg
Phone +7 343 2338000
Fax +7 343 2337788
[email protected]
www.ebmpapst.ur.ru
Switzerland
ebm-papst AG
Rütisbergstrasse 1
CH-8156 Oberhasli
Phone +41 44 73220-70
Fax +41 44 73220-77
[email protected]
www.ebmpapst.ch
Norway
ebm-papst AS
P.B. 173 Holmlia
N-1203 Oslo
Phone +47 22 763340
Fax +47 22 619173
[email protected]
www.ebmpapst.no
ebm-papst Rus GmbH
proezd 4529, vladenie 5, stroenie 1
RU-141000 Mytistschi, Oblast Moskau
Phone +7 495 9807524
Fax +7 495 5140924
[email protected]
www.ebmpapst.ru
Turkey
Akantel Elektronik San. Tic. LTD. Sti.
Atatürk Organize Sanayi
Bölgesi 10007 SK. No.:6
TR-35620 Cigli-Izmir
Phone +90 232 3282090
Fax +90 232 3280270
[email protected]
www.ebmpapst.com.tr
Poland
ebm-papst Polska Sp. z o.o.
ul. Annopol 4A
PL-03236 Warszawa
Phone +48 22 6757819
Fax +48 22 6769587
[email protected]
www.ebmpapst.pl
Portugal
ebm-papst (Portugal), Lda.
Centro Empresarial de Alverca
Rua de Adarse, Vale D’Ervas
Corpo D / Fracção 3
P-2615-178 Alverca do Ribatejo
Phone +351 218 394 880
Fax +351 218 394 759
[email protected]
www.ebmpapst.pt
Romania
ebm-papst Romania S.R.L.
Str. Tarnavei Nr. 20
RO-500327 Brasov
Phone +40 268 331859
Fax +40 268 312805
[email protected]
68
Serbia & Montenegro
ebm-papst Industries Kft.
Ezred u. 2.
H-1044 Budapest
Phone +36 1 8722-190
Fax +36 1 8722-194
[email protected]
Spain
ebm-papst Ibérica S.L.
Avda. del Sistema Solar, 29
E-28830 San Fernando de Henares (Madrid)
Phone +34 91 6780894
Fax +34 91 6781530
[email protected]
www.ebmpapst.es
Sweden
ebm-papst AB
Äggelundavägen 2
S-17562 Järfälla
Phone +46 10 4544400
Fax +46 8 362306
[email protected]
www.ebmpapst.se
Ukraine
ebm-papst Ukraine LLC
Lepse Boulevard, 4, Building 21
UA-03067 Kiev
Phone +38 044 2063091
Fax +38 044 2063091
[email protected]
www.ebmpapst.ua
United Kingdom
ebm-papst UK Ltd.
Chelmsford Business Park
GB-Chelmsford Essex CM2 5EZ
Phone +44 1245 468555
Fax +44 1245 466336
[email protected]
www.ebmpapst.co.uk
ebm-papst Automotive & Drives (UK) Ltd.
The Smithy
Fidlers Lane
GB-East Ilsley, Berkshire RG20 7LG
Phone +44 1635 2811-11
Fax +44 1635 2811-61
A&[email protected]
www.ebmpapst-ad.com
ebm-papst in America and Africa
America
Argentina
ebm-papst de Argentina S.A.
Hernandarias 148 Lomas del Mirador
Pcia. de Buenos Aires (1752)
Phone +54 11 46576135
Fax +54 11 46572092
[email protected]
www.ebmpapst.com.ar
Brazil
ebm-papst Motores Ventiladores Ltda.
Av. José Giorgi, 301 Galpões B6+B7
Condominio Logical Center
BR-06707-100 Cotia - São Paulo
Phone +55 11 4613-8700
Fax +55 11 4777-1456
[email protected]
www.ebmpapst.com.br
USA
ebm-papst Inc.
P.O. Box 4009
100 Hyde Road
USA-Farmington, CT 06034
Phone +1 860 674-1515
Fax +1 860 674-8536
[email protected]
www.ebmpapst.us
ebm-papst Automotive & Drives, Inc.
3200 Greenfield, Suite 255
USA-Dearborn, MI 48120
Phone +1 313 406-8080
Fax +1 313 406-8081
[email protected]
www.ebmpapst-automotive.us
Africa
South Africa
ebm-papst South Africa (Pty) Ltd.
P.O. Box 3124
1119 Yacht Avenue
ZA-2040 Honeydew
Phone +27 11 794-3434
Fax +27 11 794-5020
[email protected]
www.ebmpapst.co.za
Canada
ebm-papst Canada Inc.
1800 Ironstone Manor, Unit 2
CDN-Pickering, Ontario, L1W3J9
Phone +1 905 420-3533
Fax +1 905 420-3772
[email protected]
www.ebmpapst.ca
Mexico
ebm Industrial S. de R.L. de C.V.
Paseo de Tamarindos 400-A-5to Piso
Col. Bosques de las Lomas
MEX-Mexico 05120, D.F.
Phone +52 55 3300-5144
Fax +52 55 3300-5243
[email protected]
www.ebmpapst.com.mx
69
fan agent
compact fan agent
ebm-papst in Asia and Australia
motor specialist
motor agent
Asia
China
ebm-papst Ventilator (Shanghai) Co., Ltd.
No. 418, Huajing Road
WaiGaoQiao Free Trade Zone
No. 2001, Yang Gao (N) Road
VRC-200131 Shanghai, P.R. of China
Phone +86 21 5046-0183
Fax +86 21 5046-1119
[email protected]
www.ebmpapst.com.cn
Hong Kong
ebm-papst Hong Kong Ltd.
Unit No. 13,9 / F
Technology Park, 18 On Lai Street
Siu Lek Yuen, Shatin N.T.
Hong Kong - P.R. of China
Phone +852 2145-8678
Fax +852 2145-7678
[email protected]
India
ebm-papst India Pvt. Ltd.
26/3, G.N.T. Road, Erukkencherry
IND-Chennai-600118
Phone +91 44 25372556
Fax +91 44 25371149
[email protected]
www.ebmpapst.in
Indonesia
ebm-papst Indonesia
Representative Office
German Centre, 4th Floor, Suite 4470
Jl. Kapt. Subijono Dj. Bumi Serpong Damai
RI-15321 Tangerang
Phone +62 21 5376250
Fax +62 21 5388305
[email protected]
Israel
Polak Bros. Import Agencies Ltd.
9 Hamefalsim Street
IL-Kiryat Arie, Petach-Tikva 49514
Phone +972 3 9100300
Fax +972 3 5796679
[email protected]
www.polak.co.il
70
Japan
ebm-papst Industries Japan K.K.
12th Floor, Benex S-3 Bldg.
3-20-8 Shinyokohama, Kohoku-ku
J-222-0033 Yokohama
Phone +81 45 47057-51
Fax +81 45 47057-52
[email protected]
www.ebmpapst.jp
Thailand
ebm-papst Thailand Co., Ltd.
99/9 Moo 2, Central Chaengwattana Tower
14th Floor, Room 1402
Chaengwattana Road Bangtarad, Pakkret
THA-11120 Nonthaburi
Phone +66 2 8353785-7
Fax +66 2 8353788
[email protected]
Korea
ebm-papst Korea Co. Ltd.
6F, Trutec Bldg.
B 6-2, Digital Media City (DMC)
Sangam-Dong, Mapo-Gu
ROK-Seoul 121-270
Phone +82 2 366213-24
Fax +82 2 366213-26
[email protected]
www.ebmpapst.co.kr
United Arab Emirates
ebm-papst Middle East FZE
PO Box 17755
Jebel Ali Free Zone / FZS1 / AP05
UAE-Dubai
Phone +971 4 88608-26
Fax +971 4 88608-27
[email protected]
www.ebmpapst.ae
Malaysia
ebm-papst Malaysia
Representative Office
Unit 12-2, Jalan USJ Sentral 3
Persiaran Subang, Selangor Darul Ehsan
MAL-47600 Subang Jaya
Phone +60 3 8024-1680
Fax +60 3 8024-8718
[email protected]
Singapore
ebm-papst SEA Pte. Ltd.
No. 23 Ubi Road 4
#06-00 Olympia Industrial Building
SGP-Singapore 408620
Phone +65 65513789
Fax +65 68428439
[email protected]
Taiwan
ETECO Engineering & Trading Corp.
10F-I, No. 92, Teh-Wei Str.
RC-Tsow-Inn District, Kaohsiung
Phone +886 7 557-4268
Fax +886 7 557-2788
[email protected]
www.ebmpapst.com.tw
Vietnam
ebm-papst Vietnam
Representative Office
Room #102, 25 Nguyen Van Thu Street
District 1
VN-Ho Chi Minh City
Phone +84 8 39104099
Fax +84 8 39103970
[email protected]
Australia
Australia
ebm-papst A&NZ Pty Ltd.
10 Oxford Road
AUS-Laverton North, Victoria, 3026
Phone +61 3 9360-6400
Fax +61 3 9360-6464
[email protected]
www.ebmpapst.com.au
New Zealand
ebm-papst A&NZ Pty Ltd.
102 Henderson Valley Road
NZ-Henderson, Auckland 1230
Phone +64 9 837-1884
Fax +64 9 837-1899
[email protected]
www.ebmpapst.com.au
71
37804-7-8811 · 2012-10 · KD-3’
Printed in Germany
ebm-papst
ebm-papst
ebm-papst
Mulfingen GmbH & Co. KG
St. Georgen GmbH & Co. KG
Landshut GmbH
Bachmühle 2
Hermann-Papst-Straße 1
Hofmark-Aich-Straße 25
D-74673 Mulfingen
D-78112 St. Georgen
D-84030 Landshut
Phone +49 7938 81-0
Phone +49 7724 81-0
Phone +49 871 707-0
Fax +49 7938 81-110
Fax +49 7724 81-1309
Fax +49 871 707-465
[email protected]
[email protected]
[email protected]
www.ebmpapst.com