DN05034/D Enhanced PWM LEDDimming Circuit Description The NCL30051LEDGEVB LED driver evaluation board provides PWM dimming capability via gating the resonant half bridge converter on and off at the PWM rate. Effective minimum duty factor is about 10% being limited by biasing considerations. Some applications require wider range PWM dimming often extending to 1% or below. This design note presents a method to achieve PWM dimming from 100% down to less than 1% using an enhanced power control circuit. A series FET switch is introduced in the driver output to interrupt the LED current in response to the PWM control signal. This method allows the converter to maintain proper bias conditions needed to support dimming over an extremely wide dimming range. http://onsemi.com DESIGN NOTE The feedback control utilizes the sample and hold feature in the evaluation board to maintain consistent drive conditions for the LED load while dimming. Additional control circuits monitor LED current and automatically limit power during start up or transient conditions. A latch-off feature is included to avoid stress induced during shorted load conditions. Table 1. DEVICE DETAILS Device Application Input Voltage Output Power Topology Isolation NCL30051 + NCS1002 LED Dimming 90−305 Vac 50 W CrM PFC + Resonant Half Bridge Isolated Table 2. OTHER SPECIFICATIONS LED Output Output Current 1A Ripple N/A Nominal Voltage 50 V Max Voltage 54 V PFC (Yes/No) Yes Typical Efficiency 87% Inrush Limiting/Fuse Thermistor + Fuse Cooling Method/Supply Orientation Convection/Any Signal Level Control Low Voltage PWM Present Solution When switching resumes, the operating point voltage of the half bridge capacitors C6 and C7 is shifted as the transformer charges output capacitors C18 and C19 along with current flowing to the LEDs. The operating point at C6 and C7 is restored after a few half bridge cycles. This effect results in some current overshoot in the LEDs. Figure 1 shows typical PWM dimming for the NCL30051LEDGEVB evaluation board. The PWM control signal is shown in the top green trace. The middle purple trace is C6 and C7 half bridge capacitor voltage, and the lower trace is the LED current in blue. Note the short duration overshoot in LED current. The PWM dimming control of the evaluation board activates a sample and hold circuit to maintain the regulation point when the LED current is off. The PWM signal is routed to the primary side of the converter through an opto coupler. The resonant half bridge driver is switched off when the PWM dimming signal is issued. LED current decays to zero as the output capacitors discharge. When the PWM dimming signal commands the LED current to resume, the half bridge controller always begins operation by turning on the lower half bridge switch first. This allows the charge pump for the upper switch to properly bias. © Semiconductor Components Industries, LLC, 2013 November, 2013 − Rev. 1 1 Publication Order Number: DN05034/D DN05034/D operating current is set higher than the peak of the normal ripple current seen by the LEDs. This ensures that under normal operation, the FET load switch is fully conducting which minimizes power loss. Diode D102 couples the gate of Q102 load switch to transistor Q6 on the evaluation board. When the PWM signal activates Q6, the sample and hold FET Q5 is activated and the FET load switch Q102 is turned off halting the current to the LEDs. The PWM control signal restores current flow to the LEDs and turns off the sample and hold. The on/off cycle repeats at the PWM control frequency. Op amp U101B forms the constant current source by sampling the voltage across R22 and comparing to a divided reference voltage. This circuit is critical under output overload conditions. The constant current function limits LED current and ensures that adequate secondary bias voltage is available to maintain feedback control. The resonant half bridge converter remains operational which supplies power to the secondary side. Opto coupler U2 and surrounding components are not required and can be removed. Figure 1. NCL30051 PWM Dimming Enhanced Solution In the schematic of Figure 2, FET Q102 is inserted in series with the cathode lead of the LED load forming a load switch. The gate of the FET is biased on with a simple op amp constant current source which utilizes the existing current sense resistor R22 of the evaluation board. The D16 MBRF10H150 + T1 C21 C18 4.7uF C20 LED Anode 0.1uF 0.1uF Q101 D102 MMBTA06 C19 4.7uF MMBD4148 R105 R109 100 1k Q102 NTD6414 − R22 0.10 LED Cathode R107 10k R103 4.7k R110 R101 Vcc = 14V 47k 5 8 + 6 R106 220k 2 − 1 + 4 3 Internal R102 3.01k R104 Q6 MMBTA06 470pF 7 − 4.7k C101 U101B R108 D101 47k 7.5V PWM In R36 1k R37 10k U101A NCS1002 C102 2.5V 1uF 100k Added PWM Circuitry Figure 2. PWM Control Schematic As an example, if the output was shorted and the FET switch not in place, there would not be any voltage in the secondary available to control the power supply. Note that under a short circuit condition, Q102 load switch is operating in a linear region dissipating significant power. Op amp U101A monitors the state of Q102 and starts an RC http://onsemi.com 2 DN05034/D timer (R108 and C102) when the Q102 is operating in the linear mode. After a delay, the U101A shuts down the current source through D101 and latches it off. This prevents overheating Q102. The ac input power must be recycled to restore operation. BJT Q101 forms a very fast acting current limiter in case the LED output is shorted while at full operating voltage. This transistor quickly limits the current by controlling Q102 through R109 until U101B can respond and provide constant current control. Figure 5 shows an expanded view of the above. Performance Characteristics Figure 3 shows PWM dimming performance with similar timing to that shown in Figure 1. Note there is virtually no current overshoot. Figure 5. Expanded View of 5% PWM Dimming Figure 6 below shows 1% PWM dimming. Figure 3. Enhanced PWM Response Dimming with 5% duty factor at 200 Hz rate is shown in Figure 4. The PWM control signal is the green trace on top and the LED current is the lower trace at 333 mA div. Figure 6. 1% PWM Dimming This dimming approach works well for very wide duty factors as well. Figure 7 shows the PWM control signal in green on the top trace and the LED current below that in blue. This is 99% dimming at 200 Hz rate. Note the ripple in the LED current is pass-through of the 120 Hz ripple due to required low bandwidth of the PFC control loop. This solution utilizes low value non-electrolytic capacitors as the main secondary filter. Figure 4. 5% Dimming at 200 Hz http://onsemi.com 3 DN05034/D Figure 7. 99% Dimming at 200 Hz Figure 9. Start Up into Short Circuit Figure 8 below is an expanded view of the 99% dimming shown in the figure above. Shorting the output of any power supply while it is operating can generate high surge currents as the filter capacitors rapidly discharge. The PWM control circuit includes provisions to control the current stress and then turn the output current off after a delay. Figure 10 below shows the output current profile with the converter driving a 50 V load at 1 A and then a short is applied across the output. The current is shut off after about 45 msec. Figure 8. Expanded View of 99% Dimming The examples above depict dimming with a 200 Hz frequency. Higher frequencies yield similar results and this circuit is suitable up to 500 Hz operation. Overload operation The PWM control circuit must maintain proper operation during overload conditions as described earlier. Figure 9 shows the NCL30051LEDGEVB evaluation board with the modified PWM control at initial start up with a short placed on the output. The current scale is 667 mA/division. Peak current is about 1.67 A. The RC timer function shuts the LED current off after about 64 msec. Figure 10. Output Current http://onsemi.com 4 DN05034/D The data below shows performance of the NCL30051LEDGEVB evaluation board in its original configuration with a 14 LED load and no PWM dimming. Vin: 115 V ac Iin: 0.45 A rms Pin: 51.13 W PF: 0.99 THDi: 9.8% Iout: 975 mA Vout: 46.1 V Conclusion Output Power: Efficiency: [2] Evaluation Board Documents This design note illustrates how to improve the secondary side control circuitry to allow dimming to very narrow duty ratios. It has been demonstrated and tested by adding a small amount of additional circuitry and interfacing it to the NCL30051LEDGEVB evaluation board. This can enhance PWM dimming performance providing a wider operating range and more precise current waveform. References [1] NCL30051/D Data Sheet 44.9 W 87.9 % The performance of the NCL30051LEDGEVB evaluation board is not significantly impacted by the added PWM control circuitry. The data below shows performance with a 14 LED load and no PWM dimming. Vin: 115 V ac Iin: 0.46 A rms Pin: 51.86 W PF: 0.99 THDi: 9.7% Iout: 975 mA Vout: 46.3 V Output Power: Efficiency: 45.1 W 87.0 % A bill of materials for the modifications to the NCL30051LEDGEVB evaluation board and the additional components required as shown in the schematic of Figure 2 is included at the end of this document. http://onsemi.com 5 DN05034/D Table 3. BILL OF MATERIALS Designator Qty Description Footprint Manufacturer Manufacturer Part Number Substitution Allowed COMPONENT CHANGES ON NCL30051LEDGEVB EVALUATION BOARD R39 1 2.7 kW 0.25 W 1% 1206 Delete Part R40 1 1.2 kW 0.25 W 1% 1206 Delete Part R42 1 5.1 kW 0.25 W 1% 1206 Delete Part Q7 1 NPN SOT−23 Delete Part U2 1 Opto Coupler SMT Delete Part R37, R41 2 10 kW 0.25 W 1% 1206 R36 1 1 kW 0.25 W 1% 1206 Delete Part Panasonic ERJ−8ENF1001V Yes ERJ−3EKF4702V Yes COMPONENTS FOR ENHANCED PWM DIMMING CONTROL R101, R108 2 47 kW 0.1 W 1% 0603 Panasonic R102 1 3.01 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF3011V Yes R103, R110 2 4.7 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF4701V Yes R104 1 100 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF1003V Yes R105 1 1 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF1001V Yes R106 1 220 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF2203V Yes R107 1 10 kW 0.1 W 1% 0603 Panasonic ERJ−3EKF1002V Yes R109 1 100 W 0.1 W 1% 0603 Panasonic ERJ−3EKF1000V Yes U101 1 Dual Op Amp/Ref SOIC−8 ON Semiconductor NCS1002 No Q101 1 NPN SOT−23 ON Semiconductor MMBTA06 No Q102 1 N−FET DPAK ON Semiconductor NTD6414 No D101 1 7.5 V Zener SOD 123 ON Semiconductor MMSZ7V5 No D102 1 Diode SOD 123 ON Semiconductor MMBD4148 No C101 1 470 pF 50 V 0603 TDK C1608X7R1H471K Yes C102 1 1 mF 25 V 0603 TDK C1608Y5V1E105Z Yes ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative DN05034/D