Download

P

Ideas for Wireless Solutions
802.15.4-Modem PAN4580
OUTLINES-ENWC9A31x5EF
The PAN4580 module is a long range, low power, 2.4GHz ISM
band transceiver which includes a complete 802.15.4 physical
layer (PHY). It is designed for the IEEE 802.15.4
wireless standard. Using an appropriate microcontroller (MCU)
with reference oscillator provides a cost effective solution for
long range data links and networks.
The PAN4580 comes pre-loaded with the Synapse
SNAP® mesh network operating system. This module will
comply to CE and FCC / IC. A pin and function compatible
modem, called PAN2580, is also available for the 868MHz and
915MHz range.
M
ODULES
Panasonic
Electronic Devices Europe GmbH
IRELESS
W
FEATURES
-
-
small size SMD device (29.8mm x 19.0mm x 2.7mm)
3 antenna options: Single port 50Ω, ceramic antenna or plug
16 selectable Channels with up to 2 Mbps RF raw data rate
Low power modes for increased battery life
High sensitivity: -99dBm typ. @ 250kbps & 1% Packet Error Rate
+3.0 dBm @ 2.4GHz Pout programmable over a 20 dB range
Low supply voltage (1.6 V to 3.6 V, 3.0 V typ.)
Operating temperature range -40°C to +85°C
128k total Flash with 69.5k used by SNAP core, 58.5k free for
uploadable scripts when using SNAP.
2 UART with HW Flow Control for control or transparent data
33 GPIOs and up to 8 A/D inputs with 10 Bit ADC for fast and
easy conversion from analog inputs -such as temperature,
pressure and fluid levels- to digital values.
OQPSK Modulation
Mesh (SNAP®) Meshnetworking Topology with 16 Channels
APPLICATIONS
-
Wireless Sensor Networks, e.g. Lighting Control
Inventory management, Factory- and home automation
Monitoring (environmental, patient or fitness)
Automatic Meter Reading on 2,4 GHz
Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt
regarding the safety of this product, kindly inform us immediately for technical consultation.
4580-100-101 Rev. B1
www.pideu.panasonic.de
[email protected]
Hardware Status:
Mass Production
P
CONTACT
Dipl.-Ing.
Mathias Hopp
Product Manager
Wireless Connectivity
Corporate Marketing
Panasonic Industrial Devices Europe GmbH
Zeppelinstrasse 19
21337 Lüneburg, Germany
Tel.: +49 (0)4131-899-283
Fax: +49 (0)4131-899-187
[email protected]
BLOCK DIAGRAM
UFL
Connector
Vsupply
Analog &
Digital I/O
UART0 / UART1
SPI
ATMEGA128RFA1
RF-Transceiver
& uC
RX/TX
Ceramic
Antenna
Filter
I2C
Bottom
Pad
Crystal
16 MHz
Crystal
32.768kHz
PAN4580
TECHNICAL CHARACTERISTICS
Parameter
Value
Condition / Note
Receiver Sensitivity
-99 dBm typ.
@ 1% packet error rate and 250kbps
Output Power
+3,0 dBm
typical @2,4 GHz
1.9 V to 3.6 V
single supply, 3.0 V typ.
Power Supply
Data Rate
Current Consumption
receive mode
transmit mode
sleep mode
Operating Temperature Range
250 kbps
over the air, when using SNAP
17 mA typ.
20 mA @ 3,0 dBm
<1µA
@ max output power
with internal timer running
-40°C to +85°C
Notes:
All parameters are valid for VSupply = 3.0V and Tamb = 25°C.
Software from Synapse Wireless Inc. will run on this module, to create a wireless mesh network.
Also a pin compatible 868/915MHz version with the same Synapse software is available, called PAN2580.
ORDERING CODE
Hardware-Description
PAN Number
Synapse Software
No Software
PAN4580 internal ceramic antenna
PAN4580A
ENWC9A31A5EF
ENWC9A31A1EF
PAN4580 UFL version
PAN4580B
ENWC9A31B5EF
ENWC9A31B1EF
PAN4580 bottom pad version
PAN4580C
ENWC9A31C5EF
ENWC9A31C1EF
www.pideu.panasonic.de
[email protected]
Hardware Status:
Mass Production