P Ideas for Wireless Solutions Bluetooth Classic and Low Energy embedded Dual Mode Module PAN1026 OUTLINES M ODULES Panasonic Electronic Devices Europe GmbH IRELESS W PAN1026 is based on Toshiba´s single chip TC35661 Bluetooth semiconductor device with embedded Toshiba Bluetooth SIG certified stack. The TC35661 is a highly integrated and compact Bluetooth controller that delivers high-speed operation at ultra-low power consumption. It significantly reduces external component count and power consumption in applications requiring support of Bluetooth 2.1 and 4.0 standards. EDR (enhanced data rate) is not supported. An embedded SPP (Serial Port Profile of Bluetooth Classic) and GATT (Generic Attribute Profile of Bluetooth LE) are also integrated. The device can also be run in a standard Bluetooth HCI mode. The device allows for serving both legacy Bluetooth classic and Bluetooth Low Energy connections with rapid connection and disconnection, needed by a wide range of application, all at a small form factor . The PAN1026 Module is manufactured in a very small 15.6 * 8.7 * 1.9 mm3 SMD package with shielded case and is qualified according to the Bluetooth 2.1 and 4.0 standard. FCC, IC and CE approval are available. FEATURES General - Bluetooth Classic and BLE (Dual Mode) support - Bluetooth Classic 2.1 embedded SPP, high level API commands - Bluetooth 4.0 (LE) embedded GATT profile with high level API commands, compatible to Toshiba reference BLE profiles - Standard and extended HCI command set supported - Operational Temperature Range -40 / 85 degree C - Operational Voltage 1.8V or 3.0V +/- 10% - Dimension 15,6*8,7*1,9mm3 Interfaces - UART, I2C , GPIO (10 input/output pins), Wake-Up control pins Bluetooth 4.0 - GAP support for SPP - GAP peripheral support for LE - GATT Server and Client Mode are supported for LE Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt Design and Specifications are subject to change without notice. Ask the factory for technical specifications before purchase and/or use. If there is any doubt regarding the safety of this product, kindly inform us immediately for technical consultation. PAN1026 regarding the safety of this product, kindly inform us immediately for technical consultation. PAN1026 BT2.1/4.0 BT2.1/3.0 Rev. Rev. 1.2 0.2 Hardware Status: Pre-Production P CONTACT Dipl.-Ing. Mathias Hopp Product Manager Wireless Connectivity Panasonic Electronic Devices Europe GmbH Zeppelinstrasse 19 21337 Lüneburg, Germany Tel. +49-4131-899-283 Fax +49-4131-899-187 [email protected] APPLICATIONS - 2.4 GHz Bluetooth Classic Systems - 2.4 GHz Bluetooth Low Energy Systems - Health Care, Medical Diagnostic Systems - Sports and leisure equipment - Mobile phone accessories BT 2.1 and 4.0 - Consumer Electronics - Remote Controls - Health Care and Medical - Heart Rate Monitor - Blood Glucose Meter - Industrial Measurement BLOCK DIAGRAM EEPROM I2C VCC/VSS UART (4) GPIO (10) Slow Clock 32.768 kHz Wake Up Input Wake Up Output Antenna Toshiba 1-chip Dual Mode Bluetooth LSI TC35661-501 (Modem & Firmware) Crystal 26 MHz Filter PAN1026 TECHNICAL CHARACTERISTICS Parameter 0,1% BER Receiver Sensitivity (1% PER) Output Power Power Supply Transmit Mode Receive Mode Operating Temperature Range Value - 88 dBm 4 dBm 1.8V or 3.0V 46mA 46mA -40C / +85C Condition / Note @ 500 kpbs / MSK (high-gain mode) Maximum setting Single operation voltage ACL, DH1 ACL, DH1 Industrial Range Hardware Status: Pre-Production