Description Purpose and application The DIM MULTIeco control unit controls the lighting at the workplace and in offices according to the level of daylight and the presence of persons to increase comfort and save energy. DIM MULTIeco The control unit can be installed in luminaires (e.g. floor standing luminaires) or in suspended ceilings. Function The control unit can be operated in two different operating modes, see also “Setting the operating mode”: Brightness control The sensors measure the brightness in the area to be regulated and keep this to an adjustable set value by introducing artificial light according to the amount of daylight available. The sensors also detect the presence of people. When the level of daylight is sufficient or people are no longer present, the connected luminaires switch off after an adjustable delay period. START Control Unit Operating instructions Motion? 10 s – 60 min no Luminaire OFF yes Artificial light required? no yes Luminaire manually switched off 30 s ago? no Luminaire ON yes Brightness control, presence detection and automatic switch-on can be activated and deactivated using various modes. Brightness reduction If persons are present, the luminaires are dimmed to an adjustable brightness value. If no persons are present, the brightness drops to a fixed standby value of 50%, 30% or 10% after an adjustable delay time. Automatic switch-on and automatic switch-off during periods of prolonged absence can be activated and deactivated using various modes. Design The control unit is made up of the following components: A G F E D L N DIM MULTIeco • Adjusting screw for switch-off delay time (A) Sensor B L’ 1…10 V+ 1…10 V - C • Sensor connection (B) • DIP switch (C) • Pushbutton connection (D) • Control line connection (E) • Load contact (F) opcional • Power supply connection (G) Operation Symbols Pushbutton on the luminaire Luminaire on Switch on Luminaire off DIM_MULTIeco_ba1010en_we1.01.indd Switch off Luminaire flashes OSRAM GmbH Kunden Service Center Customer-Service-Center (CSC) Short press (< 0.5 s) Brightness with automat. control Steinerne Furt 62 86167 Augsburg Germany Long press (> 0.5 s) Confirmation of the setting Tel : +49 (0) 1803 677 - 200 (kostenpflichtig / charges apply) Fax.: +49 (0) 1803 677 - 202 Double-click Manual dimming X 2010 www.osram.com www.osram.de 40083215072732 4008321507273 Presence detection (detection of small movements) Page 1 of 4 DIP Operation (cont.) T1 X X X* X X X – X* X* X* – X – –X –– 1 – – + 15 s Presence detection Brightness control The device is delivered with both functions switched on. *Does not switch on via sensor. Manual switch-on required. 2 **Automatic switch-off after expiry of the switch-off delay time (motion independent). 2 + 15 –s min DIP switch 1 = ON DIP switch 2 = ON The following functions are switched on and off using DIP switches 3, 4 and 5, see Table T1: – X* – –** 1 ON “Brightness control” operating mode 1 2 3 4 5 –X* ––** min Via DIP switch 1 and 2. DIP Xs + 15 min Adjusting the operating mode 1 2 3 4 5 X* X*+ 15 s min– 1 ON 2 1 2 T2 max 1 X 1 X* < 30 s 2 X X – ON 2 : X* X* X – X – –– X* – –X** 1 2 3 4 5 ON DIP 1 2 3 4 5 DIP switch 1 = ON DIP switch 2 = OFF Standby: 50% DIP switch 1 = OFF DIP switch 2 = ON Standby: 30% min 2 – – – X** Standby: 2 10% 2 + 15 s The following minfunctions are switched on and off using DIP switches 3, 4 and 5, see Table T2: 2x 3 2 + 15 s DIP switch 1 = OFF 1 DIP switch 2 = OFF Presence detection 1 2x 1 2x > 30 s DIP + 15 s X X 2x 2 max : X 1 < 30 s 2x > 30 s 1 1 “Brightness reduction” operating mode + 15 s : 2 utomatic switch-off of the luminaires after expiry of A twice the switch-off delay time *Does not switch on via sensor. Manual switch-on required. **Motion independent 3 max + 15 s Manually switching luminaire on and off A Via short press. 1 max 1 2 3 A max 1 2 ... B > 30 s 2 Changing the brightness manually 3 ... B 1 2 Note: In the “Brightness reduction” operating mode, manual switch-off of the luminaires is not possible. Note: Function is locked if necessary, see “Locking and releasing pushbutton functions”. 1 2 Via long press. 3 Each repeated long key button press causes a toggle between increased brightness and decreased brightness. 1 2 The brightness control is deactivated until the next time the luminaire is switched on. 3 Adjusting the set value/brightness value Note: Function is locked if necessary, see “Locking and releasing pushbutton functions”. 2x 1 < 30 s 2 In the “Brightness control” operating mode the setting corresponds to the set value for the automatic brightness control (tip: make the setting when there is little daylight). 3 In the “Brightness reduction” operating mode, the setting corresponds to the fixed brightness value to which it is dimmed when movement is detected. Set the desired brightness. Double-click. Confirmation: Luminaire flashes. A max 1 2 3 ... B Page 2 of 4 A max 1 2 3 Deactivating presence detection via ... pushbutton Operation (cont.) B Note: Function is locked if necessary, see “Locking and releasing pushbutton functions”. 1 2 min min Switch on if necessary. Double-click. Confirmation: Luminaire switches off. Green LED on the + 15 s 2 1 2 min + 15 s Locking and releasing pushbutton functions + 15 s Lock preset reference and deactivation of the presence detection 1 2 Set the minimum brightness and press the pushbutton for 1 2 min max max 1 min + 15 s Lock the preset reference and manual brightness change + 15 s + 15 s 1 2 Re-release all pushbutton functions > 30 s Press the pushbutton for 30 seconds. max 2 2 3 1 < 30 s 2 3 Note: When the presence detection is activated, each time a movement is detected, the countdown of the time restarts. Turn the adjusting screw to the required setting: 60 min 10 s 1 Adjusting the switch-off delay time 5 15 30 1 2 Confirmation: Luminaire flashes. 2 + 15 s > 30 s < 30 s another 15 seconds. Confirmation: Luminaire flashes. > 30 s 1 2x Set the maximum brightness and press the pushbutton for 2 2 1 another 15 seconds. Confirmation: Luminaire flashes. + 15 s 1 1 1 sensor lights continuously. The presence detection is activated again the next time the luminaire is switched on by pushbutton if presence detection is switched on and active through selection of the corresponding operating mode. 2 1 2x Deactivate presence detection: + 15 s 1 min When presence detection is active, the green LED on the sensor lights up briefly each time motion is detected. 3 • To the left: shorter (min. 10 s) time • To the right: longer (max. 60 min) 2 Behaviour after a power failure A max 1 2 3 1 2 3 1 < 30 s 2 3 1 2 3 1 2 3 A After a power failure, the luminaire remains switched off until the next time presence is detected or a pushbutton is operated. max 2x B ... B ... If the “Automatic switch-off” function is switched on in the “Brightness reduction” operating mode, the luminaire switches on with the standby value after a power failure. A max 1 2 3 B 1 2 ... 3 Page 3 of 4 Troubleshooting Operation (cont.) If you cannot remedy the fault, please contact the Customer Service department of the luminaire manufacturer. Luminaire does not function No mains voltage available. à Check whether the green LED is lit. Use a voltage tester to test if mains voltage is present. Illuminant is faulty. à Replace illuminant. The luminaire was switched off via the pushbutton. à Switch on luminaire. The sensor is exposed to excessive amounts of ambient light. à Cover the sensor and observe the behaviour of the luminaire. A set value for the brightness cannot be specified Preset reference is locked. à Unlock the set value specification. Brightness control is switched off in the selected operating mode. à Select a suitable operating mode. Brightness is not adjusted to the selected set value Pushbutton was not pressed within 30 seconds after setting the set value (presence detection is activated) à Double-click within 30 seconds after carrying out manual dimming. Brightness control was not started until 5 seconds after the set value was adjusted. à Wait until the delay time expires. Brightness control was deactivated by a manual operation. à Switch luminaire off and on again. Brightness control is switched off in the selected operating mode. à Select a suitable operating mode. Presence detection is not functional The luminaire was switched off by pushbutton less than 30 seconds ago. à Wait until the delay time expires. The workplace is not fully within the detection area of the sensor. à Move your hand in front of one of the sensors. If the LED in the sensor does not flash, realign the sensor to the workplace. Presence detection is deactivated à Activate presence detection by briefly pressing the pushbutton. Presence detection is switched off in the selected operating mode. à Select a suitable operating mode. No artificial light is necessary. à See “Function”. Presence detection cannot be deactivated Brightness was manually changed within the last 30 seconds. à Wait until the delay time expires. Presence detection is switched off in the selected operating mode. à Select a suitable operating mode. Luminaire does not react as expected to the press of a button Pushbutton was pressed too long or too short. à See “Manually changing brightness”. Manual brightness change is locked. à See “Locking and releasing pushbutton functions”. Appendix Accessories Designation/Description The CE requirements to EN 60928 are fulfilled. The EMC requirements to EN 61547 are fulfilled LS/PD MULTI 3 Light and motion sensor LS/PD MULTI 3 B Light and motion sensor, movable LS/PD MULTI 3 FL Light and motion sensor, flat LS/PD MULTI3 CI Light and motion sensor for ceiling installation Y-CONNECTOR Branching element for the connection of additional sensors Y-CONNECTOR Screw Branching element with screw terminal for connection of additional sensors and for connection of MULTIeco systems with central presence detection ECO CI KIT Cable strain relief for the independent installation of the MULTIeco control unit (e.g. ceiling installation) SENSOR KIT Adapter for the surface mounting of the LS/PD CI sensor Conformity with the relevant EU directives is confirmed by the CE symbol. Page 4 of 4 Product number 4050300802138 4050300803081 4008321047342 4008321916648 4050300803135 4008321916686 4008321392091 4008321916662