MB2S

MB1S THRU MB10S
SURFACE MOUNT
GLASS PASSIVATED BRIDGE RECTIFIER
R
Reverse Voltage: 100 to 1000 Volts
Forward Current: 1.0 Amps
S E M I C O N D U C T O R
MBS
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
Glass passivated chip junction
0.165(4.1)
Rating to 1000V PRV
0.142(3.6)
Ideal for printed circuit board
High temperature soldering guaranteed:260 C/10 seconds at terminals
Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
0.252(7.0)
0.236(6.4)
0.031(0.8)
0.019(0.5)
MECHANICAL DATA
Case: MBS molded plastic body
Epoxy: UL94V-0 rate flame retardant
Terminals: Plated leads solderable per MIL-STD-750,method 2026
Mounting Position: Any
Weight: 0.0044ounce, 0.125 gram
0.106(2.7)
0.090(2.3)
0.043(1.1)
0.028(0.7)
0.193(4.9)
0.177(4.5)
0.069(1.7)
0.051(1.3)
0.106(2.7)
0.090(2.3)
0.008(0.20)
0.002(0.05)
0.014(0.35)
0.006(0.15)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
(Rating at 25 C ambient temperature unless otherwise specified. Single phase ,half wave ,60HZ,resistive or inductive
load. For capacitive load,derate current by 20%.)
Units
Symbols
MB1S
MB2S
MB4S
MB6S
MB8S
MB10S
100
200
400
600
800
1000
70
140
280
420
560
700
Maximum DC Blocking Voltage
VRRM
VRMS
VDC
100
200
400
600
800
1000
Maximum Average Forward Rectified Current
I(AV)
1.0
Amp
Peak Forward Surge Current 8.3ms single half
sine-wave superimposed on rated load
(JEDEC method)
IFSM
30
Amps
VF
1.1
Volts
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum Instantaneous Forward Voltage
at 1.0 A DC
Maximum DC Reverse Current
at rated DC blocking voltage
TA=25 C
TA=125 C
Typical junction capacitance(Note2)
Typical thermal resistence(Note1)
Operating junction and storage temperature
range
Volts
Volts
Volts
5
IR
A
100
PF
15
CJ
R
JA
75
R
JC
30
TJ
TSTG
℃/W
-55 to +150
C
Note: 1.On glass epoxy P.C.B. mounted on 0.05×0.05"(1.3×1.3mm) pads.
2.Measured at 1MHZ and applied reverse voltage of 4.0 Volts.
JINAN JINGHENG ELECTRONICS CO., LTD.
2-1
HTTP://WWW.JINGHENGGROUP.COM
REV:A
DATE:2013-08-13
RATINGS AND CHARACTERISTIC CURVES MB1S THRU MB10S
FIG.2-MAXIMUM NON-REPETITIVE
FORWARD SURGE CURRENT
FIG.1-TYPRCAL FORWARD CURRENT
DERATING CURVE
0.7
Aluminum Substrate
30
PEAK FORWARD SURGE
CURRENT(AMPERES)
AVERAGE FORWARD CURRENT (A)
0.8
0.6
0.5
0.4
0.3
0.2
Glass Epoxy P.C.B.
TA=25 C
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
20
10
0
0.1
1
5
10
50
100
NUMBER OF CYCLES AT 60Hz
0
0
20
40
60
80
100
120
140
160
AMBIENT TEMPERATURE ( C)
FIG4-TYPICAL FORWARD CHARACTERISTICS
FIG3-TYPICAL JUNCTION CAPACITANCE
INSTANTANEOUS FORWARD CURRENT( AMPERES)
JUNCTION CAPACITANCE(pF)
100
10
0
1
4
100
10
REVERSE VOLTAGE. (V)
10
1
0.1
TA=25 C
Pulse Width=300 s
1% Duty Cycle
0.01
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE (VOLTS)
INSTANTANEOUS REVERSE CURRENT ( uA)
FIG.5-TYPICAL REVERSE CHARACTERISTICS
100
Tj=125 C
10
1
Tj=25 C
0.1
0.01
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE(%)
JINAN JINGHENG ELECTRONICS CO., LTD.
2-2
HTTP://WWW.JINGHENGGROUP.COM
REV:A
DATE:2013-08-13