B1S THRU B10S SURFACE MOUNT GLASS PASSIVATED BRIDGE RECTIFIER R Reverse Voltage: 100 to 1000 Volts Forward Current: 1.0 Amps S E M I C O N D U C T O R MBS FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Glass passivated chip junction 0.165(4.1) Rating to 1000V PRV 0.142(3.6) Ideal for printed circuit board High temperature soldering guaranteed:260 C/10 seconds at terminals Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC 0.252(7.0) 0.236(6.4) 0.031(0.8) 0.019(0.5) MECHANICAL DATA Case: MBS molded plastic body Epoxy: UL94V-0 rate flame retardant Terminals: Plated leads solderable per MIL-STD-750,method 2026 Mounting Position: Any Weight: 0.0044ounce, 0.125 gram 0.106(2.7) 0.090(2.3) 0.043(1.1) 0.028(0.7) 0.193(4.9) 0.177(4.5) 0.069(1.7) 0.051(1.3) 0.106(2.7) 0.090(2.3) 0.008(0.20) 0.002(0.05) 0.014(0.35) 0.006(0.15) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS (Rating at 25 C ambient temperature unless otherwise specified. Single phase ,half wave ,60HZ,resistive or inductive load. For capacitive load,derate current by 20%.) Symbols B1S B2S B4S B6S B8S B10S Units 100 200 400 600 800 1000 70 140 280 420 560 700 Maximum DC Blocking Voltage VRRM VRMS VDC 100 200 400 600 800 1000 Volts Volts Volts Maximum Average Forward Rectified Current I(AV) 1.0 Amp Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 30 Amps VF 1.1 Volts Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at rated DC blocking voltage TA=25 C TA=125 C Typical junction capacitance(Note2) Typical thermal resistence(Note1) Operating junction and storage temperature range 5 IR A 100 PF 15 CJ R JA 75 R JC 30 TJ TSTG ℃/W -55 to +150 C Note: 1.On glass epoxy P.C.B. mounted on 0.05×0.05"(1.3×1.3mm) pads. 2.Measured at 1MHZ and applied reverse voltage of 4.0 Volts. JINAN JINGHENG ELECTRONICS CO., LTD. 2-1 HTTP://WWW.JINGHENGGROUP.COM REV:B DATE:2013-08-13 RATINGS AND CHARACTERISTIC CURVES B1S THRU B10S FIG.2-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT FIG.1-TYPRCAL FORWARD CURRENT DERATING CURVE 0.7 Aluminum Substrate 30 0.6 PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT (A) 0.8 0.5 0.4 0.3 0.2 Glass Epoxy P.C.B. TA=25 C 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 20 10 0 0.1 1 5 10 50 100 NUMBER OF CYCLES AT 60Hz 0 0 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE ( C) FIG4-TYPICAL FORWARD CHARACTERISTICS FIG3-TYPICAL JUNCTION CAPACITANCE INSTANTANEOUS FORWARD CURRENT( AMPERES) JUNCTION CAPACITANCE(pF) 100 10 0 1 4 100 10 REVERSE VOLTAGE. (V) 10 1 0.1 TA=25 C Pulse Width=300 s 1% Duty Cycle 0.01 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) INSTANTANEOUS REVERSE CURRENT ( uA) FIG.5-TYPICAL REVERSE CHARACTERISTICS 100 Tj=125 C 10 1 Tj=25 C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE(%) JINAN JINGHENG ELECTRONICS CO., LTD. 2-2 HTTP://WWW.JINGHENGGROUP.COM REV:B DATE:2013-08-13