R MB2F-MB10F Single Phase 1.0 AMP Glass Passivated Bridge Rectifiers S E M I C O N D U C T O R VOLTAGE RANGE FEATURES 200 to 1000 Volts CURRENT Ideal for printed circuit board Reliable low cost construction technique results in inexpensive product ● High temperature soldering guaranteed : 260 °C / 10 seconds / 0.375” ( 9.5mm ) lead length at 5 lbs., ( 2.3 kg ) tension ● ● 1.0Ampere MBF + 0.158(4.0) 0.142(3.6) MECHANICAL DATA Case : Molded Plastic ● Epoxy : Device has UL flammability classification 94V-0 ● Mounting Position : Any ● Marking : Type Number ~ ● 0.012(0.35) ~ 0.296(7.5)MAX 0.042(1.05) 0.018(0.45) 0.075(1.90) 0.193(4.9) 0.022(0.55) 0.177(4.5) 0.063(1.6) 0.051(1.3) 0.109(2.8) 0.086(2.2) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current -On glass-epoxy P.C.B. -On aluminum substrate Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave superimposed on rated load (JEDEC Method) I2t Rating for Fusing (t < 8.3ms) Forward Voltage per element Peak Reverse Current At Rated DC Blocking Voltage @IF = 1.0A @TA = 25°C @TA = 125°C Symbol MB2F VRRM VRWM VR 200V VR(RMS) 140V Operating and Storage Temperature Range MB6F 400V 280V MB8F MB10F Unit 600V 800V 1000V V 420V 560V V 700V IO 1.0 A IFSM 40 A I2t 10 A 2s VFM 0.99 V IRM 10 150 µA Cj 25 pF 62.5 25 °C/W -55 to +150 °C Typical Junction Capacitance per leg (Note 2) Typical Thermal Resistance per leg (Note 1) MB4F R R JA JL Tj, TSTG Note: 1. On aluminum suvstrate P.C.B. with an area of 0.8×0.8”(20×20mm) mounted on 0.05×0.05”(1.3×1.3mm) solder pad. 2. On glass epoxy P.C.B. mouted on 0.05×0.05”(1.3×1.3mm) pads. JINAN JINGHENG ELECTRONICS CO., LTD. 2-1 HTTP://WWW.JINGHENGGROUP.COM MB2F-MB10F RATING AND CHARACTERISTIC CURVES 1.6 FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 100 FIG.2- TYPICAL REVERSE CHARACTERISTICS PER BRIDGE ELEMENT 1.2 ALUMINA SUBSTRATE 50.8mm X 50.8mm SOLDERING LAND 1mm X 1mm CONDUCTOR LAYER 20 mm SUBSTRATE THICKNESS 0.64mm SIN 1.0 0.8 0.6 0.4 0.2 0 0 40 20 60 80 100 120 140 160 INSTANTANEOUS REVERSE CURRENT. ( A) AVERAGE FORWARD CURRENT. (A) 1.4 10 Tj=100 0C 1 Tj=75 0C 0.1 Tj=25 0C 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 600 35 30 25 IFSM 20 10ms 10ms 1 Cycle Ta=40 C NON-REPETITIVE, Single Half Sine-Wave SINE(JEDEC WAVE, Method) Tj = 25OC BEFORE SURGE CURRENT IS APPLIED 15 10 5 500 Tj=25 0C 400 300 200 100 10 NUMBER OF CYCLES (CYCLE) 1 50 INSTANTANEOUS FORWARD CURRENT. (A) 1000 JUNCTION CAPACITANCE.(pF) PEAK FORWARD SURGE CURRENT. (A) 40 FIG.4- TYPICAL JUNCTION CAPACITANCE FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 0 0.1 0.5 1 2 10 50 100 5 20 REVERSE VOLTAGE. (V) 200 500 800 FIG.5- TYPICAL FORWARD CHARACTERISTICS 10 1 0.1 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE. (V) JINAN JINGHENG ELECTRONICS CO., LTD. 2-2 HTTP://WWW.JINGHENGGROUP.COM