MB05F-MB10F Silicon Bridge Rectifiers VOLTAGE RANGE: 50 --- 1000 V CURRENT: 0.5 A MBF Features 4.8±0.2 3.8±0.2 Mechanical Data 1.2±0.2 This series is UL recognized under Component Index, file number E239431 Glass passivated chip junctions Plastic materrial has U/L flammability classification 94V-O High surge overload rating: 25A peak Saves space on printed circuit boards High temperature soldering guaranteed: 260°C/10 seconds at 5 lbs. (2.0kg) tension 1. 4±0.2 0.6±0.1 1.0±0.15 2.5±0.25 Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Dimensions in inches and (millimeters) Mounting Position: Any Weight: 0.0078 ounce, 0.22 gram 0.3±0.1 6.8±0.2 Dimensions in millimeters MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified. Single phase,half wave,60 Hz,resistive or inductive load. For capacitive load,derate by 20%. MB05F MB1F MB2F MB4F MB6F MB8F MB10F UNITS Maximum recurrent peak reverse voltage V RRM 50 100 200 400 600 800 1000 V Maximum RMS voltage V RMS 35 70 140 280 420 560 700 V Maximum DC blocking voltage V DC 50 100 200 400 600 800 1000 V Maximum average forw ard output current @TA=25 IF(AV) 0.5 A IFSM 25 A VF 1.0 V 5.0 μA 0.5 mA CJ 13 pF R θJA RθJL 85 20 TJ - 55 ---- + 150 TSTG - 55 ---- + 150 Peak forw ard surge current 8.3ms single half-sine-w ave superimposed on rated load Maximum instantaneous forw ard voltage @ 0.4 A Maximum reverse current at rated DC blocking voltage @TA=25 @TA=100 Typical junction capacitance per leg (NOTE 3) Typical thermal resistance per leg (NOTE 1) (NOTE 2) Operating junction temperature range Storage temperature range IR NOTES: (1) On glass epoxy P.C.B. mounted on 0.05 x 0.05" (1.3 x 1.3mm) pads (2) On aluminum substrate P.C.B. with an area of 0.8" x 0.8" (20 x 20mm) mounted on 0.05 x 0.05" (1.3 x 1.3mm) solder pad (3) Measured at 1.0 MHz and applied rev erse v oltage of 4.0 Volts /W MB05F-MB10F Silicon Bridge Rectifiers Ratings AND Charactieristic Curves AVERAGE FORWARD CURRENT, AMPERES FIG.1 -- DERATING CURVE FOR OUTPUT RRECTIFIED CURRENT 0.8 Aluminum Substrate 0.7 GLASS EPOXY P.C.B. 0.6 0.5 0.4 0.3 0.2 0.1 0 RESISTIVE OR INDUCTIVE LOAD 30 0 60 90 120 150 PEAK FORWARD SURGE CURRENT, AMPERES FIG.2 -- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG TＡ=４０ SINGLE HALF SINE-WAVE (JEDEC Method) 30 25 f=60Hz 20 15 f=50Hz 10 1.0 CYCLE 5.0 0 1 10 100 NUMBER OF CYCLES AT 50/60Hz AMBIENT TEMPERATURE, 10 1 INSTANTANEOUS REVERSE CURRENT, MICRO AMPERES FIG.4 -- TYPICAL REVERSE CHARACTERISTIC FIG.3 -- TYPICAL FORWARD VOLTAGE KKKKCHARACTERISTICS PER LEG TJ=25 0.1 0.01 0.2 0.6 0.8 1.0 1.2 TJ=125 10 1.0 0.1 TJ=25 .01 20 0 40 60 80 100 FIG.5 -- TYPICAL JUNCTION CAPACITANCE PER BBBBBBB ELEMENT PULSE WIDTH=300µS 0.4 100 PERCENT OF RATED PEAK REVERSE VOLTAGE,% 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS CAPACITANCE, pF AMPERES INSTANTANEOUS FORWARD CURRENT, 35 100 60 f=1MHz TJ=25 40 20 10 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE, VOLTS 100