US1G

US1A TH R U US1M
R
GLASS PASSIVATED JUNCTION
HIGH EFFICIENCY RECTIFIER
Reverse Voltage: 50 to 1000 Volts
Forward Current:1.0Ampere
S E M I C O N D U C T O R
FEATURES
SMA(DO-214AC)
Plastic package has Underwriters Laboratory Flammability Classification 94V-0
Glass passived junction
Low forward voltage drop
High current capability, High reliability
Low power loss, high efficiency
High surge current capability
High speed switching, Low leakage
High temperature soldering guaranteed:260°C/10 seconds at terminals
Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
0.114(2.9)
0.100(2.54)
0.065(1.65)
0.049(1.25)
0.181(4.60)
0.157(3.99)
0.012(0.305)
0.006(0.152)
0.096(2.44)
0.078(1.98)
MECHANICAL DATA
0.008(0.203)
MAX
0.060(1.52)
0.030(0.76)
Case: JEDEC SMA(DO-214AC) molded plastic body
Terminals: Solder Plated, solderable per MIL-STD-750,method 2026
Polarity: Color band denotes cathode end
Weight: 0.002ounce, 0.064 gram
0.22(5.6)
0.189(4.80)
Dimensions in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
(Rating at 25°C ambient temperature unless otherwise specified. Single phase ,half wave ,60HZ,resistive or inductive
load. For capacitive load, derate current by 20%.)
Symbols
US1A US1B
US1D
US1F
US1G
US1J
US1K
US1M
Units
50
100
200
300
400
600
800
1000
35
70
140
210
280
420
560
700
50
100
200
300
400
600
800
1000
Volts
Volts
Volts
Maximum DC Blocking Voltage
VRRM
VRMS
VDC
Maximum Average Forward Rectified Current
0.375"(9.5mm)lead length @ at TA=55 C
I(AV)
1.0
Amp
Peak Forward Surge Current 8.3ms single half
sine-wave superimposed on rated load
(JEDEC method)
IFSM
30.0
Amps
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum Instantaneous Forward Voltage
at 1.0 A
Maximum DC Reverse Current
at rated DC blocking voltage
VF
1.30
1.0
1.7
5.0
TA=25 C
IR
A
50
TA=125 C
Typical Thermal resistance
Maximum reverse recovery time(Note1)
Typical junction capacitance(Note2)
Operating junction and storage temperature
range
Volts
R
R
JA
75
JL
27
Trr
CJ
TJ
TSTG
C/W
50
75
ns
15
10
PF
-55 to+150
C
Note: 1.Test conditions: IF=0.5A,IR=1.0A,IRR=0.25A.
2.Measured at 1MHZ and applied reverse voltage of 4.0 Volts.
JINAN JINGHENG ELECTRONICS CO., LTD.
2-1
HTTP://WWW.JINGHENGGROUP.COM
RATINGS AND CHARACTERISTIC CURVES US1A THRU US1M
FIG.2-TYPICAL FORWARD CURRENT
DERATING CURVE
50
NONINDUCTIVE
(+)
50Vdc
(APPROX)
10
NONINDUCTIVE
(-)
1
NONINDUCTIVE
Trr
+0.5A
0
PULSE
GENERATOR
(NOTE2)
D.U.T.
AVERAGE FORWARD CURRENT (A)
FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE
RECOVERY TIME CHARACTERISTIC
-0.25A
OSCILLOSCOPE
(NOTE1)
-1.0A
NOTES:1.Rise Time=7ns max. input impedance=1
megohm 22pF
2.Rise Time=10ns max. source impedance=
50 ohms
0.8
0.6
0.4
SINGLE PHASE HALF WAVE 60HZ
RESISTIVE OR INDUCTIVE LOAD
0.2
0
0
1cm
25
50
75
100
125
150
175
AMBIENT TEMPERATURE ( C)
SET TIME BASE FOR 50/100 ns/cm
FIG.3-TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
FIG.4-TYPICAL REVERSE CHARACTERISTICS
10
100
INSTANTANEOUS REVERSE CURRENT ( A)
INSTANTANEOUS FORWARD CURRENT( A)
1.0
50\100\200\300V
1
400\500V
0.1
600\800\1000V
TJ=25°C
0.01
Pulse Width=300 s
1% Duty Cycle
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
TJ=150°C
TJ=100°C
1.0
TJ=25°C
0.1
0.01
0.001
0
10
0
20
1.8
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE(%)
INSTANTANEOUS FORWARD VOLTAGE (VOLTS)
FIG.5-MAXIMUM NON-REPETITIVE
FORWARD SURGE CURRENT
FIG.6-TYPICAL JUNCTION CAPACITANCE
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
40
JUNCTION CAPACITANCE(pF)
PEAK FORWARD SURGE
CURRENT(AMPERES)
50
30
20
10
0
1
5
10
50
200
100
60
40
20
6
4
TJ=25°C
US1J-US1M
2
1
100
NUMBER OF CYCLES AT 60Hz
US1A-US1G
10
0.1 0.2
0.4
1
2
4
10
20
40
REVERSE VOLTAGE. (V)
JINAN JINGHENG ELECTRONICS CO., LTD.
2-2
HTTP://WWW.JINGHENGGROUP.COM
100