TDA7210

Wireless Components
ASK/FSK Single Conversion Receiver
TDA7210 Version 1.0
Data Sheet December 2008
Revision History
Current Version: 1.0 as of 03.12.08
Previous Version: none
Page
(in previous
Version)
Page(s)
(in current
Version)
Subjects (major changes since last revision)
We Listen to Your Comments
Is there any information in this document that you feel is wrong, unclear or missing?
Your feedback will help us to continuously improve the quality of this document.
Please send your proposal (including a reference to this document) to:
[email protected]
Edition December 2008
Published by Infineon Technologies AG,
Am Campeon 1 - 12
85579 Neubiberg, Germany
© 2008 Infineon Technologies AG
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated
herein.
Information
For further information on technology, delivery terms and conditions, and prices, please contact the nearest Infineon Technologies Office in Germany or
the Infineon Technologies Companies and Infineon Technologies Representatives worldwide (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest
Infineon Technologies Office.
Infineon Technologies Components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a
failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness
of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/
or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
TDA7210
Product Info
Product Info
General Description
Features
Application
The IC is a very low power consump- Package
tion single chip FSK/ASK Superheterodyne Receiver (SHR) for the
frequency bands 810 to 870 MHz and
400 to 440 MHz that is pin compatible
with the Receiver TDA5210. The IC
offers a high level of integration and
needs only a few external components. The device contains a low noise
amplifier (LNA), a double balanced
mixer, a fully integrated VCO, a PLL
synthesiser, a crystal oscillator, a limiter with RSSI generator, a PLL FSK
demodulator, a data filter, a data comparator (slicer) and a peak detector.
Additionally there is a power down feature to save battery life.
■
Low supply current (typ. at 868MHz
Is = 5.9mA in FSK mode,
Is = 5.2mA in ASK mode)
■
Selectable frequency ranges 810870 MHz and 400-440 MHz
■
Supply voltage range 5V ±10%
■
Limiter with RSSI generation,
operating at 10.7MHz
■
Power down mode with very low
supply current (50nA typ)
■
Selectable reference frequency
■
FSK and ASK demodulation capability
■
2nd order low pass data filter with
external capacitors
■
Fully integrated VCO and PLL
Synthesiser
■
Data slicer with self-adjusting
threshold
■
ASK sensitivity < –107dBm
■
FSK sensitivity <-100dBm
■
Keyless Entry Systems
■
Alarm Systems
■
Remote Control Systems
■
Low Bitrate Communication
Systems
Ordering Information
Type
Ordering Code
Package
TDA7210
SP000524274
PG-TSSOP-28
samples available on tape and reel
Wireless Components
Product Info
Data Sheet, December 2008
1
Table of Contents
1 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
i
2 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
2.1
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.2
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2.4
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
3.1
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
3.2
Pin Definition and Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3.3
Functional Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
3.4
Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
3.4.1 Low Noise Amplifier (LNA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
3.4.2 Mixer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
3.4.3 PLL Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
3.4.4 Crystal Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
3.4.5 Limiter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
3.4.6 FSK Demodulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
3.4.7 Data Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
3.4.8 Data Slicer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
3.4.9 Peak Detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
3.4.10 Bandgap Reference Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
4 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
4.1
Choice of LNA Threshold Voltage and Time Constant. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
4.2
Data Filter Design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4.3
Quartz Load Capacitance Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
4.4
Quartz Frequency Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
4.5
Data Slicer Threshold Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
4.6
ASK/FSK Switch Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
4.6.1 FSK Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
4.6.2 ASK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
4.7
Principle of the Precharge Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
5 Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
5.1
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
5.1.2 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
5.1.3 AC/DC Characteristics at TAMB = 25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5.1.4 AC/DC Characteristics at TAMB = -40 to 85°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
5.2
Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
5.3
Test Board Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
5.4
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
2
Product Description
Contents of this Chapter
2.1
2.2
2.3
2.4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Package Outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
TDA7210
Product Description
2.1 Overview
The IC is a very low power consumption single chip FSK/ASK Superheterodyne
Receiver (SHR) for the frequency bands 810 to 870 MHz and 400 to 440 MHz
that is pin compatible with the Receiver TDA5210. The IC offers a high level of
integration and needs only a few external components. The device contains a
low noise amplifier (LNA), a double balanced mixer, a fully integrated VCO, a
PLL synthesiser, a crystal oscillator, a limiter with RSSI generator, a PLL FSK
demodulator, a data filter, a data comparator (slicer) and a peak detector. Additionally there is a power down feature to save battery life.
2.2 Application
■
Keyless Entry Systems
■
Remote Control Systems
■
Alarm Systems
■
Low Bitrate Communication Systems
2.3 Features
Wireless Components
■
Low supply current (at 868MHz Is = 5.9 mA typ. FSK mode, 5.2mA typ. ASK
mode)
■
Supply voltage range 5V ±10%
■
Power down mode with very low supply current (50nA typ)
■
FSK and ASK demodulation capability
■
Fully integrated VCO and PLL Synthesiser
■
RF input sensitivity ASK < –107dBm
■
RF input sensitivity FSK < –100dBm
■
Selectable frequency ranges 810-870 MHz and 400-440 MHz
■
Selectable reference frequency
■
Limiter with RSSI generation, operating at 10.7MHz
■
2nd order low pass data filter with external capacitors
■
Data slicer with self-adjusting threshold
2-2
Data Sheet, December 2008
TDA7210
Product Description
2.4 Package Outlines
PG_TSSOP_28.EPS
Figure 2-1
Wireless Components
PG-TSSOP-28 package outlines
2-3
Data Sheet, December 2008
3
Functional Description
Contents of this Chapter
3.1
3.2
3.3
3.4
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Pin Definition and Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Functional Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
TDA7210
Functional Description
3.1 Pin Configuration
CRST1
1
28
CRST2
VCC
2
27
PDWN
LNI
3
26
PDO
TAGC
4
25
DATA
AGND
5
24
3VOUT
LNO
6
23
THRES
VCC
7
22
FFB
MI
8
21
OPP
MIX
9
20
SLN
AGND
10
19
SLP
FSEL
11
18
LIMX
TDA 7210
IFO
12
17
LIM
DGND
13
16
CSEL
VDD
14
15
MSEL
Pin_Configuration_7210.wmf
Figure 3-1
Wireless Components
IC Pin Configuration
3-2
Data Sheet, December 2008
TDA7210
Functional Description
3.2 Pin Definition and Function
In the subsequent table the internal circuits connected to the pins of the device
are shown. ESD-protection circuits are omitted to ease reading.
.
Table 3-1 Pin Definition and Function
Pin No.
Symbol
1
CRST1
Equivalent I/O-Schematic
Function
External Crystal Connector 1
4.15V
1
50uA
2
VCC
5V Supply
3
LNI
LNA Input
57uA
3
500uA
4k
1k
Wireless Components
3-3
Data Sheet, December 2008
TDA7210
Functional Description
4
TAGC
AGC Time Constant Control
4.3V
4.2uA
4
1k
1.5uA
1.7V
5
AGND
Analogue Ground Return
6
LNO
LNA Output
5V
1k
6
7
VCC
8
MI
5V Supply
Mixer Input
1.7V
2k
9
2k
MIX
Complementary Mixer Input
8
9
400uA
10
AGND
Wireless Components
Analogue Ground Return
3-4
Data Sheet, December 2008
TDA7210
Functional Description
11
FSEL
868/434 MHz Operating Frequency Selector
750
1.2V
2k
11
12
IFO
10.7 MHz IF Mixer Output
300uA
2.2V
60
12
4.5k
13
DGND
Digital Ground Return
14
VDD
5V Supply (PLL Counter Circuitry)
15
MSEL
ASK/FSK Modulation Format
Selector
1.2V
3.6k
15
Wireless Components
3-5
Data Sheet, December 2008
TDA7210
Functional Description
16
CSEL
6.xx or 13.xx MHz Quartz
Selector
1.2V
80k
16
17
LIM
Limiter Input
2.4V
15k
17
18
Complementary Limiter Input
LIMX
75uA
330
18
15k
19
SLP
Data Slicer Positive Input
15uA
100
3k
19
80µA
Wireless Components
3-6
Data Sheet, December 2008
TDA7210
Functional Description
20
SLN
Data Slicer Negative Input
5uA
10k
20
21
OPP
OpAmp Noninverting Input
5uA
200
21
22
FFB
Data Filter Feedback Pin
5uA
100k
22
23
THRES
AGC Threshold Input
5uA
10k
23
24
3VOUT
3V Reference Output
24
20kΩ
3.1V
Wireless Components
3-7
Data Sheet, December 2008
TDA7210
Functional Description
25
DATA
Data Output
500
25
40k
26
PDO
Peak Detector Output
200
26
27
PDWN
Power Down Input
27
220k
220k
28
CRST2
External Crystal Connector 2
4.15V
28
50uA
Wireless Components
3-8
Data Sheet, December 2008
TDA7210
Functional Description
3.3 Functional Block Diagram
VCC
IF
Filter
MSEL
LNO
MI
6
LNI
RF
3
MIX
8
9
LIM
IFO
12
LIMX
17
FFB
15
18
OPP
22
SLP
21
SLN
19
20
LNA
+ FSK
- ASK
+
SLICER
+
OP
25
4
PEAK
26
DETECTOR
TDA 7210
OTA
:1 / 2
VCC
DATA
-
TAGC
FSK
PLL Demod
+
LIMITER
VCO
: 128 / 64
Φ
DET
UREF
CRYSTAL
OSC
AGC
Reference
PDO
23
THRES
24
3VOUT
14
Bandgap
Reference
Loop
Filter
DGND
13
2,7
5,10
VCC AGND
11
FSEL
16
1
28
27
PDWN
CSEL
Crystal
Function_7200.wmf
Figure 3-2
Wireless Components
Main Block Diagram
3-9
Data Sheet, December 2008
TDA7210
Functional Description
3.4 Functional Blocks
3.4.1
Low Noise Amplifier (LNA)
The LNA is an on-chip cascode amplifier with a voltage gain of 15 to 20dB. The
gain figure is determined by the external matching networks situated ahead of
LNA and between the LNA output LNO (Pin 6) and the Mixer Inputs MI and MIX
(Pins 8 and 9). The noise figure of the LNA is approximately 3dB, the current
consumption is 500µA. The gain can be reduced by approximately 18dB. The
switching point of this AGC action can be determined externally by applying a
threshold voltage at the THRES pin (Pin 23). This voltage is compared internally
with the received signal (RSSI) level generated by the limiter circuitry. In case
that the RSSI level is higher than the threshold voltage the LNA gain is reduced
and vice versa. The threshold voltage can be generated by attaching a voltage
divider between the 3VOUT pin (Pin 24) which provides a temperature stable
3V output generated from the internal bandgap voltage and the THRES pin as
described in Section 4.1. The time constant of the AGC action can be determined by connecting a capacitor to the TAGC pin (Pin 4) and should be chosen
along with the appropriate threshold voltage according to the intended operating case and interference scenario to be expected during operation. The optimum choice of AGC time constant and the threshold voltage is described in
Section 4.1.
3.4.2
Mixer
The Double Balanced Mixer downconverts the input frequency (RF) in the
range of 400-440MHz/810-870MHz to the intermediate frequency (IF) at
10.7MHz with a voltage gain of approximately 21dB by utilising either high- or
low-side injection of the local oscillator signal. In case the mixer is interfaced
only single-ended, the unused mixer input has to be tied to ground via a capacitor. The mixer is followed by a low pass filter with a corner frequency of 20MHz
in order to suppress RF signals to appear at the IF output (IFO pin). The IF output is internally consisting of an emitter follower that has a source impedance
of approximately 330 Ω to facilitate interfacing the pin directly to a standard
10.7MHz ceramic filter without additional matching circuitry.
3.4.3
PLL Synthesizer
The Phase Locked Loop synthesiser consists of a VCO, an asynchronous
divider chain, a phase detector with charge pump and a loop filter and is fully
implemented on-chip. The VCO is including on-chip spiral inductors and varactor diodes. It’s nominal centre frequency is 840MHz, the operating range guaranteed over the temperature range specified is 820 to 860MHz. Depending on
whether high- or low-side injection of the local oscillator is used the receive frequency ranges are 810 to 840 and 840 to 870MHz or 400 to 420 and 420 to
440MHz (see also Section 4.4). No additional external components are neces-
Wireless Components
3 - 10
Data Sheet, December 2008
TDA7210
Functional Description
sary.
The oscillator signal is fed both to the synthesiser divider chain and to the downconverting mixer. In case of operation in the 400 to 440 MHz range, the signal
is divided by two before it is fed to the mixer. This is controlled by the selection
pin FSEL (Pin 11) as described in the following table. The overall division ratio
of the divider chain can be selected to be either 128 or 64, depending on the
frequency of the reference oscillator quartz (see below and Section 4.4). The
loop filter is also realised fully on-chip.
Table 3-2 FSEL Pin Operating States
3.4.4
FSEL
RF Frequency
Open
400-440 MHz
Shorted to ground
810-870 MHz
Crystal Oscillator
The on-chip crystal oscillator circuitry allows for utilisation of quartzes both in
the 6 and 13MHz range as the overall division ratio of the PLL can be switched
between 64 and 128 via the CSEL (Pin 16) pin according to the following table.
Table 3-3 CSEL Pin Operating States
CSEL
Crystal Frequency
Open
6.xx MHz
Shorted to ground
13.xx MHz
The calculation of the value of the necessary quartz load capacitance is shown
in Section 4.3, the quartz frequency calculation is explained in Section 4.4.
3.4.5
Limiter
The Limiter is an AC coupled multistage amplifier with a cumulative gain of
approximately 80 dB that has a bandpass-characteristic centred around
10.7 MHz. It has a typical input impedance of 330 Ω to allow for easy interfacing
to a 10.7 MHz ceramic IF filter. The limiter circuit also acts as a Receive Signal
Strength Indicator (RSSI) generator which produces a DC voltage that is
directly proportional to the input signal level as can be seen in Figure 4-2. This
signal is used to demodulate ASK-modulated receive signals in the subsequent
baseband circuitry. The RSSI output is applied to the modulation format switch,
to the Peak Detector input and to the AGC circuitry.
In order to demodulate ASK signals the MSEL pin has to be left open as
described in the next chapter.
Wireless Components
3 - 11
Data Sheet, December 2008
TDA7210
Functional Description
3.4.6
FSK Demodulator
To demodulate frequency shift keyed (FSK) signals a PLL circuit is used that is
contained fully on chip. The Limiter output differential signal is fed to the linear
phase detector as is the output of the 10.7 MHz center frequency VCO. The
demodulator gain is typically 200µV/kHz. The passive loop filter output that is
comprised fully on chip is fed to both the VCO and the modulation format switch
described in more detail below. This signal is representing the demodulated signal with high frequencies applied to the demodulator demodulated to logic ones
and low frequencies demodulated to logic zeroes. Please note that due to this
behaviour a sign inversion of the data occurs in case of high-side injection of
the local oscillator at receive frequencies below 840 or 420MHz, respectively.
See also .
The modulation format switch is actually a switchable amplifier with an AC gain
of 11 that is controlled by the MSEL pin (Pin 15) as shown in the following table.
This gain was chosen to facilitate detection in the subsequent circuits. The DC
gain is 1 in order not to saturate the subsequent Data Filter wih the DC offset
produced by the demodulator in case of large frequency offsets of the IF signal.
The resulting frequency characteristic and details on the principle of operation
of the switch are described in Section 4.6.
Table 3-4 MSEL Pin Operating States
MSEL
Modulation Format
Open
ASK
Shorted to ground
FSK
The demodulator circuit is switched off in case of reception of ASK signals.
3.4.7
Data Filter
The data filter comprises an OP-Amp with a bandwidth of 100kHz used as a
voltage follower and two 100kΩ on-chip resistors. Along with two external
capacitors a 2nd order Sallen-Key low pass filter is formed. The selection of the
capacitor values is described in Section 4.2.
3.4.8
Data Slicer
The data slicer is a fast comparator with a bandwidth of 100 kHz. This allows
for a maximum receive data rate of up to 100kBaud. The maximum achievable
data rate also depends on the IF Filter bandwidth and the local oscillator tolerance values. Both inputs are accessible. The output delivers a digital data signal (CMOS-like levels) for sbsequent circuits. The self-adjusting threshold on
pin 20 its generated by RC-term or peak detector depending on the baseband
coding scheme. The data slicer threshold generation alternatives are described
in more detail in Section 4.5.
Wireless Components
3 - 12
Data Sheet, December 2008
TDA7210
Functional Description
3.4.9
Peak Detector
The peak detector generates a DC voltage which is proportional to the peak
value of the receive data signal. An external RC network is necessary. The input
is connected to the output of the RSSI-output of the Limiter, the output is connected to the PDO pin (Pin 26 ). This output can be used as an indicator for the
received signal strength to use in wake-up circuits and as a reference for the
data slicer in ASK mode. Note that the RSSI level is also output in case of FSK
mode.
3.4.10
Bandgap Reference Circuitry
A Bandgap Reference Circuit provides a temperature stable reference voltage
for the device. A power down mode is available to switch off all subcircuits which
is controlled by the PWDN pin (Pin 27) as shown in the following table. The supply current drawn in this case is typically 50nA.
Table 3-5 PDWN Pin Operating States
PDWN
Operating State
Open or tied to ground
Powerdown Mode
Tied to Vs
Wireless Components
Receiver On
3 - 13
Data Sheet, December 2008
4
Applications
Contents of this Chapter
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Choice of LNA Threshold Voltage and Time Constant . . . . . . . . . . . . 4-2
Data Filter Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Quartz Load Capacitance Calculation . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Quartz Frequency Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Data Slicer Threshold Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7
ASK/FSK Switch Functional Description . . . . . . . . . . . . . . . . . . . . . . 4-8
Principle of the Precharge Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
TDA7210
Applications
4.1 Choice of LNA Threshold Voltage and Time Constant
In the following figure the internal circuitry of the LNA automatic gain control is
shown.
R4
R5
Uthreshold
Pins:
24
23
RSSI (0.8 - 2.8V)
20k
Ω
OTA
VCC
+3.1 V
Iload
RSSI < Uthreshold: Iload= -1.5µA
4
UC
C
LNA
Gain control
voltage
RSSI > Uthreshold: Iload=4.2µA
Uc:< 2.6V : Gain high
Uc:> 2.6V : Gain low
Ucmax= VCC - 0.7V
Ucmin = 1.67V
LNA_autom.wmf
Figure 4-1
LNA Automatic Gain Control Circuitry
The LNA automatic gain control circuitry consists of an operational transimpedance amplifier that is used to compare the received signal strength signal
(RSSI) generated by the Limiter with an externally provided threshold voltage
Uthres. As shown in the following figure the threshold voltage can have any
value between approximately 0.8 and 2.8V to provide a switching point within
the receive signal dynamic range.
This voltage Uthres is applied to the THRES pin (Pin 23) The threshold voltage
can be generated by attaching a voltage divider between the 3VOUT pin
(Pin 24) which provides a temperature stable 3V output generated from the
internal bandgap voltage and the THRES pin. If the RSSI level generated by the
Limiter is higher than Uthres, the OTA generates a positive current Iload. This
yields a voltage rise on the TAGC pin (Pin 4). Otherwise, the OTA generates a
negative current. These currents do not have the same values in order to
achieve a fast-attack and slow-release action of the AGC and are used to
charge an external capacitor which finally generates the LNA gain control voltage.
Wireless Components
4-2
Data Sheet, December 2008
TDA7210
Applications
LNA always
in high gain mode
3
2
RSSI Level Range
UTHRES Voltage Range
2.5
RSSI Level
1.5
1
LNA always
in low gain mode
0.5
0
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
Input Level at LNA Input [dBm]
RSSI-AGC.wmf
Figure 4-2
RSSI Level and Permissive AGC Threshold Levels
The switching point should be chosen according to the intended operating scenario. The determination of the optimum point is described in the accompanying
Application Note, a threshold voltage level of 1.8V is apparently a viable choice.
It should be noted that the output of the 3VOUT pin is capable of driving up to
50µA, but that the THRES pin input current is only in the region of 40nA. As the
current drawn out of the 3VOUT pin is directly related to the receiver power consumption, the power divider resistors should have high impedance values. The
sum of R1 and R2 has to be 600kΩ in order to yield 3V at the 3VOUT pin. R1
can thus be chosen as 240kΩ, R2 as 360kΩ to yield an overall 3VOUT output
current of 5µA1 and a threshold voltage of 1.8V
Note: If the LNA gain shall be kept in either high or low gain mode this has to
be accomplished by tying the THRES pin to a fixed voltage. In order to achieve
always high gain mode operation, a voltage higher than 3.3V shall be applied
to the THRES pin. A short to the 3VOLT pin will keep the LNA in high gain mode
at least over a large RF-input level range. But to switch the LNA reliable into
high gain mode over the whole RF-input level range, either a voltage higher
than 3.3V has to be applied on pin 23 as mentioned above or, as alternative, a
330k resistor in parallel with a 47nF capacitor can be connected between pin 4
and GND. Whereas the capacitor should be placed as close as possible to pin
4. In order to achieve low gain mode operation a voltage lower than 0.7V shall
be applied to the THRES, such as a short to ground.
As stated above the capacitor connected to the TAGC pin is generating the gain
control voltage of the LNA due to the charging and discharging currents of the
OTA and thus is also responsible for the AGC time constant. As the charging
and discharging currents are not equal two different time constants will result.
The time constant corresponding to the charging process of the capacitor shall
be chosen according to the data rate. According to measurements performed
at Infineon the capacitor value should be greater than 47nF.
1. note the 20kΩ resistor in series with the 3.1V internal voltage source
Wireless Components
4-3
Data Sheet, December 2008
TDA7210
Applications
4.2 Data Filter Design
Utilising the on-board voltage follower and the two 100kΩ on-chip resistors a
2nd order Sallen-Key low pass data filter can be constructed by adding 2 external capacitors between pins 19 (SLP) and 22 (FFB) and to pin 21 (OPP) as
depicted in the following figure and described in the following formulas1.
C14
Pins:
C12
22
21
R
R
100k
100k
19
Filter_Design.wmf
Figure 4-3
Data Filter Design
C14 =
2Q b
R2πf 3dB
C12 =
b
4QR π f 3 dB
with
Q=
b
a
the quality factor of the poles
where
in case of a Bessel filter a = 1.3617, b = 0.618
and thus Q = 0.577
and in case of a Butterworth filter a = 1.414, b = 1
and thus Q = 0.71
Example: Butterworth filter with f3dB = 5kHz and R = 100kΩ:
C14 = 450pF, C12 = 225pF
1. taken from Tietze/Schenk: Halbleiterschaltungstechnik, Springer Berlin, 1999
Wireless Components
4-4
Data Sheet, December 2008
TDA7210
Applications
4.3 Quartz Load Capacitance Calculation
The value of the capacitor necessary to achieve that the quartz oscillator is
operating at the intended frequency is determined by the reactive part of the
negative resistance of the oscillator circuit as shown in Section 5.1.3 and by the
quartz specifications given by the quartz manufacturer.
CS
Pin 28
Crystal
Input
impedance
Z1-28
TDA7210
Pin 1
Quartz_load.wmf
Figure 4-4
Determination of Series Capacitance Value for the Quartz Oscillator
Crystal specified with load capacitance
CS =
1
1
+ 2π f X L
CL
with CL the load capacitance (refer to the quartz crystal specification).
Examples:
6.7 MHz: CL = 12 pFXL=695ΩCS = 8.9 pF
13.4 MHz: CL = 12 pFXL=1010 ΩCS = 5.9 pF
These values may be obtained in high accuracy by putting two capacitors in
series to the quartz, such as 22pF and 15pF in the 6.7MHz case and 22pF and
8.2pF in the 13.4MHz case.
But please note that the calculated value of CS includes the parasitic capacitors
also.
Wireless Components
4-5
Data Sheet, December 2008
TDA7210
Applications
4.4 Quartz Frequency Calculation
As described in Section 3.4.3 the operating range of the on-chip VCO is 820 to
860 MHz with a nominal center frequency of 840MHz. This signal is divided by
2 before applied to the mixer in case of operation at 434 MHz. This local oscillator signal can be used to downconvert the RF signals both with high- or lowside injection at the mixer. The resulting receive frequency ranges then extend
between 810 and 870MHz or between 400 and 440MHz. Low-side injection of
the local oscillator has to be used for receive frequencies between 840 and
870MHz as well as high-side injection for receive frequencies below 840MHz.
Corresponding to that in the 400MHz region low-side injection is applicable for
receive frequencies above 420MHz, high-side injection below this frequency.
Therefore for operation both in the 868 and the 434 MHz ISM bands low-side
injection of the local oscillator has to be used. Then the local oscillator frequency is calculated by subtracting the IF frequency (10.7 MHz) from the RF
frequency (434 or 868 MHz). Please note that no sign-inversion occurs in case
of reception and demodulation of FSK-modulated signals.
The overall division ratios in the PLL are 64 or 128 in case of operation at
868 MHz or 32 and 64 in case of operation at 434 MHz, depending on the crystal frequency used as shown below. The quartz frequency in case of low-side
injection may be calculated by using the following formula:
f QU =
with
f RF ± 10.7
r
ƒRF
receive frequency
ƒLO
local oscillator (PLL) frequency (ƒRF ± 10.7)
ƒQU
quartz oscillator frequency
r
ratio of local oscillator (PLL) frequency and quartz frequency as
shown in the subsequent table
Table 4-1 Dependence of PLL Overall Division Ratio on FSEL and CSEL
FSEL
CSEL
Ratio r = (fLO/fQU)
open
open
64
open
GND
32
GND
open
128
GND
GND
64
Example (low-side injection mode):
f QU = (868.4MHz − 10.7 MHz) / 64 = 13.40156 MHz
f QU = (868 .4 MHz − 10.7 MHz ) / 128 = 6.7008 MHz
f QU = (434.2 MHz − 10.7 MHz ) / 32 = 13.23437 MHz
f QU = (434 .2 MHz − 10.7 MHz ) / 64 = 6.6172 MHz
Wireless Components
4-6
Data Sheet, December 2008
TDA7210
Applications
4.5 Data Slicer Threshold Generation
The threshold of the data slicer, especially for a coding scheme without DC-content, can be generated using an external R-C integrator as shown in Figure 45. The time constant TA of the R-C integrator has to be significantly larger than
the longest period of no signal change TL within the data sequence. For the calculation of the time constant TA please see Application Note „TDA521xANV1.1“, chapter „4.11 Data Slicer“. In order to keep distortion low, the minimum value for R1 is 20kΩ.
R1
C13
Pins:
19
data out
25
20
Uthreshold
data
filter
data slicer
Data_slice1.wmf
Figure 4-5
Data Slicer Threshold Generation with External R-C Integrator
In case of ASK operation another possibility for threshold generation is to use
the peak detector in connection with two resistors and one capacitor as shown
in the following figure. The component values are depending on the coding
scheme and the protocol used.
R3
C15
R2
Pins:
peak detector
26
19
data out
25
20
Uthreshold
data slicer
data
filter
Data_slice2.wmf
Figure 4-6
Wireless Components
Data Slicer Threshold Generation Utilising the Peak Detector
4-7
Data Sheet, December 2008
TDA7210
Applications
4.6 ASK/FSK Switch Functional Description
The TDA7210 is containing an ASK/FSK switch which can be controlled via
Pin 15 (MSEL). This switch is actually consisting of 2 operational amplifiers that
are having a gain of 1 in case of the ASK amplifier and a gain of 11 in case of
the FSK amplifier in order to achieve an appropriate demodulation gain characteristic. In order to compensate for the DC-offset generated especially in case
of the FSK PLL demodulator there is a feedback connection between the
threshold voltage of the bit slicer comparator (Pin 20) to the negative input of
the FSK switch amplifier. This is shown in the following figure.
15
MSEL
RSSI (ASK signal)
ASK/FSK Switch
Data Filter
FSK PLL Demodulator
RF1 int
DATA Out
RF2 int
+
v=1
100k
Comp
100k
25
-
RF3 int
AC
0.2 mV/kHz
ASK
+
+
FSK
-
300k
RF4 int
DC
typ. 2 V
1.5 V......2.5 V
30k
FFB
22
21
OPP
SLP
19
20
SLN
ASK mode : v=1
FSK mode : v=11
C14
C12
R1
C13
ask_fsk_datapath.WMF
Figure 4-7
4.6.1
ASK/FSK mode datapath
FSK Mode
The FSK datapath has a bandpass characterisitc due to the feedback shown
above (highpass) and the data filter (lowpass). The lower cutoff frequency f2 is
determined by the external RC-combination. The upper cutoff frequency f3 is
determined by the data filter bandwidth.
The demodulation gain of the FSK PLL demodulator is 200µV/kHz. This gain is
increased by the gain v of the FSK switch, which is 11. Therefore the resulting
dynamic gain of this circuit is 2.2mV/kHz within the bandpass. The gain for the
DC content of FSK signal remains at 200µV/kHz. The cutoff frequencies of the
bandpass have to be chosen such that the spectrum of the data signal is influenced in an acceptable amount.
In case that the user data is containing long sequences of logical zeroes the
effect of the drift-off of the bit slicer threshold voltage can be lowered if the offset
voltage inherent at the negative input of the slicer comparator (Pin20) is used.
The comparator has no hysteresis built in.
Wireless Components
4-8
Data Sheet, December 2008
TDA7210
Applications
This offset voltage is generated by the bias current of the negative input of the
comparator (i.e. 20nA) running over the external resistor R1. This voltage raises
the voltage appearing at pin 20 (e.g. 1mV with R1 = 100kΩ). In order to obtain
benefit of this asymmetrical offset for the demodulation of long zeros the lower
of the two FSK frequencies should be chosen in the transmitter as the zerosymbol frequency.
In the following figure the shape of the above mentioned bandpass is shown.
gain (pin19)
v
v-3dB
20dB/dec
-40dB/dec
3dB
0dB
f
DC
f1
f2
0.18mV/kHz
f3
2mV/kHz
frequenzgang.WMF
Figure 4-8
Frequency characterstic in case of FSK mode
The cutoff frequencies are calculated with the following formulas:
f1 =
1
R1 ⋅ 330 k Ω
⋅ C 13
2π
R1 + 330 k Ω
f 2 = v ⋅ f1 = 11 ⋅ f1
f 3 = f 3dB
f3 is the 3dB cutoff frequency of the data filter - see Section 4.2.
Example:
R1 = 100kΩ, C13 = 47nF
This leads tof1 = 44Hzandf2 = 485Hz
Wireless Components
4-9
Data Sheet, December 2008
TDA7210
Applications
4.6.2
ASK Mode
In case the receiver is operated in ASK mode the datapath frequency charactersitic is dominated by the data filter alone, thus it is lowpass shaped.The cutoff
frequency is determined by the external capacitors C12 and C14 and the internal 100k resistors as described in Section 4.2
0dB
-3dB
-40dB/dec
f
f3dB
freq_ask.WMF
Figure 4-9
Wireless Components
Frequency charcteristic in case of ASK mode
4 - 10
Data Sheet, December 2008
TDA7210
Applications
4.7 Principle of the Precharge Circuit
In case the data slicer threshold shall be generated with an external RC network
as described in Section 4.5 it is necessary to use large values for the capacitor
C13 attached to the SLN pin (pin 20) in order to achieve long time constants.
This results also from the fact that the choice of the value for R1 connected
between the SLP and SLN pins (pins 19 and 20) is limited by the 330kΩ resistor
appearing in parallel to R1 as can be seen in Figure 4-7. Apart from this a resistor value of 100kΩ leads to a voltage offset of 1mV at the comparator input as
described in Section 4.6.1. The resulting startup time constant τ1 can be calculated with:
τ 1 = (R1 || 330 k Ω ) × C 13
In case R1 is chosen to be 100kΩ and C13 is chosen as 47nF this leads to
τ 1 = (100kΩ || 330kΩ ) × 47 nF = 77 kΩ × 47 nF = 3.6ms
When the device is turned on this time constant dominates the time necessary
for the device to be able to demodulate data properly. In the powerdown mode
the capacitor is only discharged by leakage currents.
In order to reduce the turn-on time in the presence of large values of C13 a precharge circuit was included in the TDA7210 as shown in the following figure.
C18
R4+R5=600k
R5
R4
C13
R1
Uthreshold
24
19
20
23
Uc>Us
Uc<Us
Uc
Iload
Data Filter
ASK/FSK Switch
-
U2
0 / 240uA
+
Us
OTA
+
-
U2<2.4V : I=240uA
U2>2.4V : I=0
20k
+3.1V
+2.4V
precharge.WMF
Figure 4-10
Wireless Components
Principle of the precharge circuit
4 - 11
Data Sheet, December 2008
TDA7210
Applications
This circuit charges the capacitor C13 with an inrush current Iload of typically
220µA for a duration of T2 until the voltage Uc appearing on the capacitor is
equal to the voltage Us at the input of the data filter. This voltage is limited to
2.5V. As soon as these voltages are equal or the duration T2 is exceeded the
precharge circuit is disabled.
τ2 is the time constant of the charging process of C18 which can be calculated
as
τ 2 = 20 k Ω × C18
as the sum of R4 and R5 is sufficiently large and thus can be neglected. T2 can
then be calculated according to the following formula:
⎛
⎜
1
Tl = τ 2 ln⎜
2
⎜ 1 − .4V
⎜
3V
⎝
⎞
⎟
⎟ ≈ τ 2 × 1 .6
⎟
⎟
⎠
The voltage transient during the charging of C18 is shown in the following
figure:
U2
3V
2.4V
2
T2
e-fkt1.WMF
Figure 4-11
Voltage appearing on C18 during precharging process
The voltage appearing on the capacitor C13 connected to pin 20 is shown in the
following figure. It can be seen that due to the fact that it is charged by a constant current source it exhibits is a linear increase in voltage which is limited to
USmax = 2.5V which is also the approximate operating point of the data filter
input. The time constant appearing in this case can be denoted as T3, which
can be calculated with
U Smax ⋅ C13
2,5V
T3 = ------------------------------ = ----------------- ⋅ C13
220μA
220μA
Wireless Components
4 - 12
Data Sheet, December 2008
TDA7210
Applications
Uc
Us
T3
e-Fkt2.WMF
Figure 4-12
Voltage transient on capacitor C13 attached to pin 20
As an example the choice of C18 = 22nF and C13 = 47nF yields
τ2 = 0.44ms
T2 = 0.71ms
T3 = 0.53ms
This means that in this case the inrush current could flow for a duration of
0.64ms but stops already after 0.49ms when the USmax limit has been reached.
T3 should always be chosen to be shorter than T2.
It has to be noted finally that during the turn-on duration T2 the overall device
power consumption is increased by the 220µA needed to charge C13.
The precharge circuit may be disabled if C18 is not equipped. This yields a T2
close to zero. Note that the sum of R4 and R5 has to be 600kΩ in order to produce 3V at the THRES pin as this voltage is internally used also as the reference for the FSK demodulator.
Wireless Components
4 - 13
Data Sheet, December 2008
5
Reference
Contents of this Chapter
5.1
5.2
5.3
5.4
Electrical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Test Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
Test Board Layouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15
TDA7210
preliminary
Reference
5.1 Electrical Data
5.1.1
Absolute Maximum Ratings
WARNING
The maximum ratings may not be exceeded under any circumstances, not even
momentarily and individually, as permanent damage to the IC will result.
Table 5-1 Absolute Maximum Ratings, Ambient temperature TAMB=-40°C ... + 85°C
#
Parameter
Symbol
Limit Values
Unit
min
max
1
Supply Voltage
Vs
-0.3
5.5
V
2
Junction Temperature
Tj
-40
+125
°C
3
Storage Temperature
Ts
-40
+150
°C
4
Thermal Resistance
RthJA
114
K/W
5
ESD integrity, all pins excl. Pins 1,3, 6, 28
ESD integrity Pins 1,3,6,28
VESD
+2
+1.5
kV
kV
Wireless Components
5-2
Remarks
HBM
according to
MIL STD
883D,
method
3015.7
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.1.2
Operating Range
Within the operational range the IC operates as explained in the circuit description. The AC/DC characteristic limits are not guaranteed. Currents flowing into
the device are denoted as positive currents and v.v.
Supply voltage: VCC = 4.5V .. 5.5V
Table 5-2 Operating Range, Ambient temperature TAMB= -40°C ... + 85°C
#
Parameter
1
Supply Current
2
Receiver Input Level
ASK
FSK, frequ. dev. ± 50kHz
Symbol
Limit Values
Unit
min
max
ISF 868
ISF 434
ISA 868
ISA 434
4.1
3.9
3.4
3.2
7.7
7.5
7
6.8
mA
mA
mA
mA
RFin
-106
-100
-13
-13
dBm
dBm
Test Conditions /
L
Item
Notes
3
LNI Input Frequency
fRF
400/
810
440/
870
MHz
4
MI/X Input Frequency
fMI
400/
810
440/
870
MHz
5
3dB IF Frequency Range
ASK
FSK
fIF -3dB
5
10.4
23
11
MHz
6
Powerdown Mode On
PWDNON
0
0.8
V
7
Powerdown Mode Off
PWDNOFF
2
VCC
V
8
Gain Control Voltage,
LNA high gain state
VTHRES
2.8
VCC-1
V
9
Gain Control Voltage,
LNA low gain state
VTHRES
0
0.7
V
fRF = 868MHz, FSK Mode
fRF = 434MHz, FSK Mode
fRF = 868MHz, ASK Mode
fRF = 434MHz, ASK Mode
@ source impedance 50Ω,
BER 2E-3, average power
level, Manchester encoded
datarate 4kBit, 280kHz IF
Bandwidth
■
■
■ Not part of the production test - either verified by design or measured in an Infineon Evalboard as described in 2.
Wireless Components
5-3
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.1.3
AC/DC Characteristics at TAMB = 25°C
AC/DC characteristics involve the spread of values guaranteed within the specified voltage and ambient temperature range. Typical characteristics are the
median of the production. Currents flowing into the device are denoted as positive currents and vice versa. The device performance parameters marked with
■ are not part of the production test, but verified by design or measusured in
an Infineon Evalboard as described in 2.
Table 5-3 AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V
Parameter
Symbol
Limit Values
min
Unit
Test Conditions /
typ
max
50
100
nA
Pin 27 (PDWN)
open or tied to 0 V
L
Item
Notes
Supply
Supply Current
1
Supply current,
standby mode
IS PDWN
2
Supply current, device
operating in 868 MHz
range, FSK mode
ISF 868
5.1
5.9
6.7
mA
Pin 11 (FSEL) tied
to GND, Pin 15
(MSEL) tied to GND
3
Supply current, device
operating in 434 MHz
range, FSK mode
ISF 434
4.9
5.7
6.5
mA
Pin 11 (FSEL)
open, Pin 15
(MSEL) tied to GND
4
Supply current, device
operating in 868 MHz
range, ASK mode
ISA 868
4.4
5.2
6
mA
Pin 11 (FSEL) tied
to GND, Pin 15
(MSEL) open
5
Supply current, device
operating in 434 MHz
range, ASK mode
ISA 434
4.2
5
5.8
mA
Pin 11 (FSEL)
open, Pin 15
(MSEL) open
LNA
Signal Input LNI (PIN 3), VTHRES > 3.3V, high gain mode
1
Average Power Level
at BER = 2E-3
(Sensitivity) ASK
RFin
-110
dBm
Manchester
encoded datarate
4kBit, 280kHz IF
Bandwidth
2
Average Power Level
at BER = 2E-3
(Sensitivity) FSK
RFin
-103
dBm
Manchester enc.
datarate 4kBit,
280kHz IF Bandw.,
± 50kHz pk. dev.
3
Input impedance,
fRF=434 MHz
S11 LNA
0.873 / -34.7 deg
■
4
Input impedance,
fRF=869 MHz
S11 LNA
0.738 / -73.5 deg
■
5
Input level @ 1dB compression
P1dBLNA
-15
dBm
6
Input 3rd order intercept
point fRF=434 MHz
IIP3LNA
-10
dBm
matched input
■
7
Input 3rd order intercept
point fRF=869 MHz
IIP3LNA
-14
dBm
matched input
■
Wireless Components
5-4
■
■
■
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-3 AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V (continued)
Parameter
Symbol
Limit Values
min
8
LO signal feedthrough
at antenna port
typ
LOLNI
Unit
max
-73
Test Conditions /
L
Item
Notes
■
dBm
Signal Output LNO (PIN 6), VTHRES > 3.3V, high gain mode
1
Gain fRF=434 MHz
S21 LNA
1.509 / 138.2 deg
■
2
Gain fRF=869 MHz
S21 LNA
1.419 / 101.7 deg
■
3
Output impedance,
fRF=434 MHz
S22 LNA
0.886 / -12.9 deg
■
4
Output impedance,
fRF=869 MHz
S22 LNA
0.866 / -24.2 deg
■
Signal Input LNI, VTHRES = GND, low gain mode
1
Input impedance,
fRF=434 MHz
S11 LNA
0.899 / -35.4 deg
■
2
Input impedance,
fRF=869 MHz
S11 LNA
0.772 / -80.2 deg
■
3
Input level @ 1dB C. P
fRF = 434 MHz
P1dBLNA
-18
dBm
matched input
■
4
Input level @ 1dB C. P
fRF = 869 MHz
P1dBLNA
-6
dBm
matched input
■
5
Input 3rd order intercept
point fRF=434 MHz
IIP3LNA
-10
dBm
matched input
■
6
Input 3rd order intercept
point fRF=869 MHz
IIP3LNA
-5
dBm
matched input
■
Signal Output LNO, VTHRES = GND, low gain mode
1
Gain fRF=434 MHz
S21 LNA
0.183 / 140.6 deg
■
2
Gain fRF=869 MHz
S21 LNA
0.179 / 109.1deg
■
3
Output impedance,
fRF=434 MHz
S22 LNA
0.897 / -13.6 deg
■
4
Output impedance,
fRF=869 MHz
S22 LNA
0.868 / -26.3 deg
■
Antenna to IFO, VTHRES > 3.3V, high gain mode
1
Voltage Gain Antenna
to IFO fRF=434 MHz
GAnt-IFO
42
dB
2
Voltage Gain Antenna
to IFO fRF=869 MHz
GAnt-IFO
40
dB
Wireless Components
5-5
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-3 AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V (continued)
Parameter
Symbol
Limit Values
min
typ
Unit
max
Test Conditions /
L
Item
Notes
Antenna to IFO, VTHRES = GND, low gain mode
1
Voltage Gain Antenna
to IFO fRF=434 MHz
GAnt-IFO
22
dB
2
Voltage Gain Antenna
to IFO fRF=869 MHz
GAnt-IFO
19
dB
Signal 3VOUT (PIN 24)
1
Output voltage
V3VOUT
2.9
3.1
3.3
V
3VOUT Pin open
2
Current out
I3VOUT
-3
-5
-10
µA
see 2
VCC-1
V
see 2
Signal THRES (PIN 23)
1
Input Voltage range
VTHRES
0
2
LNA low gain mode
VTHRES
0
3
LNA high gain mode
VTHRES
2.81
4
Current in
ITHRES_in
V
31
3.31
5
V
voltage must not be
higher than
VCC-1V
■
nA
Signal TAGC (PIN 4)
1
Current out,
LNA low gain state
ITAGC_out
-3.6
-4.2
-5
µA
RSSI > VTHRES
2
Current in, LNA high
gain state
ITAGC_in
1
1.5
2.2
µA
RSSI<VTHRES
MIXER
Signal Input MI/MIX (PINS 8/9)
1
Input impedance,
fRF=434 MHz
S11 MIX
0.942 / -14.4 deg
■
2
Input impedance,
fRF=869 MHz
S11 MIX
0.918 / -28.1 deg
■
3
Input 3rd order intercept
point fRF=434 MHz
IIP3MIX
-28
dBm
■
4
Input 3rd order intercept
point fRF=869 MHz
IIP3MIX
-26
dBm
■
■
Signal Output IFO (PIN 12)
1
Output impedance
ZIFO
330
Ω
2
Conversion Voltage
Gain fRF=434 MHz
GMIX
+19
dB
3
Conversion Voltage
Gain fRF=869 MHz
GMIX
+18
dB
Wireless Components
5-6
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-3 AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V (continued)
Parameter
Symbol
Limit Values
Unit
min
typ
max
ZLIM
264
330
396
Ω
60
80
dB
Test Conditions /
L
Item
Notes
LIMITER
Signal Input LIM/X (PINS 17/18)
1
Input Impedance
2
RSSI dynamic range
DRRSSI
3
RSSI linearity
LINRSSI
4
Operating frequency
(3dB points)
fLIM
dB
■
23
MHz
■
100
kHz
■
±1
5
10.7
■
DATA FILTER
1
Useable bandwidth
BWBB FILT
2
RSSI Level at Data Filter Output SLP,
RFIN=-103dBm
RSSIlow
1.1
V
LNA in high gain
mode
RF=868MHz
3
RSSI Level at Data Filter Output SLP,
RFIN=-30dBm
RSSIhigh
2.65
V
LNA in high gain
mode
RF=868MHz
Slicer, Signal Output DATA (PIN 25)
1
Maximum Datarate
DRmax
2
LOW output voltage
VSLIC_L
0
3
HIGH output voltage
VSLIC_H
VCC
-1.3
IPCH_SLN
-100
Iload
-500
Ileakage
0
100
kBps
NRZ, 20pF capacitive loading
0.1
V
VCC-1
VCC
-0.7
V
Output current
=200µA
-220
-300
µA
see 2
µA
static load current must
not exceed -500µA
■
Slicer, Signal SLN (PIN 20)
1
Precharge Current Out
PEAK DETECTOR
Signal Output PDO (PIN 26)
1
Load current
2
Leakage current
200
1000
nA
14
MHz
CRYSTAL OSCILLATOR
Signals CRSTL1, CRSTL 2, (PINS 1/28)
1
Operating frequency
2
Input Impedance
@ ~6MHz
Z1-28
-825
+j695
Ω
■
3
Input Impedance
@ ~13MHz
Z1-28
-600
+j1010
Ω
■
4
Serial Capacity
@ ~6MHz
CS 6=C1
8.9
pF
5
Serial Capacity
@ ~13MHz
CS13=C1
5.9
pF
Wireless Components
fCRSTL
6
5-7
fundamental mode,
series resonance
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-3 AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V (continued)
Parameter
Symbol
Limit Values
min
typ
Unit
max
Test Conditions /
L
Item
Notes
ASK/FSK Signal Switch
Signal MSEL (PIN 15)
1
ASK Mode
VMSEL
1.4
42
V
2
FSK Mode
VMSEL
0
0.2
V
or open
FSK DEMODULATOR
1
Demodulation Gain
GFMDEM
200
2
Useable IF Bandwidth
BWIFPLL
10.2
10.7
µV/
kHz
11.2
MHz
POWER DOWN MODE
Signal PDWN (PIN 27)
1
Powerdown Mode On
PWDNON
2.8
VCC
V
2
Powerdown Mode Off
PWDNOff
0
0.8
V
3
Input bias current
PDWN
4
Start-up Time until valid
signal is detected at IF
IPDWN
19
uA
Power On Mode
TSU
<1
ms
depends on the
used crystal
VCO MULTIPLEXER
Signal FSEL (PIN 11)
1
fRF range 434 MHz
VFSEL
1.4
42
V
2
fRF range 869 MHz
VFSEL
0
0.2
V
3
Output bias current
FSEL
IFSEL
-160
-240
µA
FSEL tied to GND
or open
-200
or open
PLL DIVIDER
Signal CSEL (PIN 16)
1
fCRSTL range 6.xxMHz
VCSEL
1.4
42
V
2
fCRSTL range
13.xxMHz
VCSEL
0
0.2
V
3
Input bias current
CSEL
ICSEL
-3
-7
µA
-5
CSEL tied to GND
■ Not part of the production test - either verified by design or measured in an Infineon Evalboard as described in 2.
1) 2.8V is the voltage which is at least required that the LNA of a device is in high gain mode over the whole RFinput level range. 3.3V is required that the LNA of each device is reliable in high gain mode over the whole RFinput level range (considering also the production spread).
2) Maximum voltage in Power-On state is 4V, but in PDWN-state the maximum voltage is 2.8V.
Wireless Components
5-8
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.1.4
AC/DC Characteristics at TAMB = -40 to 85°C
Currents flowing into the device are denoted as positive currents and vice versa
Table 5-4 AC/DC Characteristics with TAMB= -40°C ... + 85°C, VCC = 4.5 ... 5.5 V
Parameter
Symbol
Limit Values
min
Unit
Test Conditions /
typ
max
50
400
nA
Pin 27 (PDWN)
open or tied to 0 V
L
Item
Notes
Supply
Supply Current
1
Supply current,
standby mode
IS PDWN
2
Supply current, device
operating in 868 MHz
range, FSK mode
ISF 868
4.1
5.9
7.7
mA
Pin 11 (FSEL) tied
to GND, Pin 15
(MSEL) tied to GND
3
Supply current, device
operating in 434 MHz
range, FSK mode
ISF 434
3.9
5.7
7.5
mA
Pin 11 (FSEL)
open, Pin 15
(MSEL) tied to GND
4
Supply current, device
operating in 868 MHz
range, ASK mode
ISA 868
3.4
5.2
7
mA
Pin 11 (FSEL) tied
to GND, Pin 15
(MSEL) open
5
Supply current, device
operating in 434 MHz
range, ASK mode
ISA 434
3.2
5
6.8
mA
Pin 11 (FSEL)
open, Pin 15
(MSEL) open
Signal 3VOUT (PIN 24)
1
Output voltage
V3VOUT
2.9
3.1
3.3
V
3VOUT Pin open
2
Current out
I3VOUT
-3
-5
-10
µA
see 2
see 2
Signal THRES (PIN 23)
1
Input Voltage range
VTHRES
0
VCC-1
V
2
LNA low gain mode
VTHRES
0
0.3
V
3
LNA high gain mode
VTHRES
2.81
3.31
V
4
Current in
ITHRES_in
31
5
voltage must not be
higher than
VCC-1V
■
nA
Signal TAGC (PIN 4)
1
Current out,
LNA low gain state
ITAGC_out
-1
-4.2
-8
µA
RSSI > VTHRES
2
Current in, LNA high
gain state
ITAGC_in
0.5
1.5
5
µA
RSSI < VTHRES
MIXER
1
Conversion Voltage
Gain fRF=434 MHz
GMIX
+19
dB
2
Conversion Voltage
Gain fRF=869 MHz
GMIX
+18
dB
Wireless Components
5-9
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-4 AC/DC Characteristics with TAMB= -40°C ... + 85°C, VCC = 4.5 ... 5.5 V
Parameter
Symbol
Limit Values
min
typ
Unit
max
Test Conditions /
L
Item
Notes
LIMITER
Signal Input LIM/X (PINS 17/18)
1
RSSI dynamic range
DRRSSI
60
80
dB
DATA FILTER
2
RSSI Level at Data Filter Output SLP,
RFIN=-103dBm
RSSIlow
1.1
V
LNA in high gain
mode
3
RSSI Level at Data Filter Output SLP,
RFIN=-30dBm
RSSIhigh
2.65
V
LNA in high gain
mode
Slicer, Signal Output DATA (PIN 25)
1
Maximum Datarate
DRmax
2
LOW output voltage
VSLIC_L
0
3
HIGH output voltage
VSLIC_H
VCC
-1.5
IPCH_SLN
-100
Iload
-400
Ileakage
0
100
kBps
NRZ, 20pF capacitive loading
0.1
V
VCC-1
VCC
-0.5
V
Output current
=200µA
-220
-300
µA
see 2
µA
static load current must
not exceed -500µA
■
Slicer, Signal SLN (PIN 20)
1
Precharge Current Out
PEAK DETECTOR
Signal Output PDO (PIN 26)
1
Load current
2
Leakage current
700
2000
nA
CRYSTAL OSCILLATOR
Signals CRSTL1, CRSTL 2, (PINS 1/28)
1
Operating frequency
fCRSTL
6
14
MHz
fundamental mode,
series resonance
ASK/FSK Signal Switch
Signal MSEL (PIN 15)
1
ASK Mode
VMSEL
1.4
42
V
2
FSK Mode
VMSEL
0
0.2
V
or open
FSK DEMODULATOR
1
Demodulation Gain
GFMDEM
2
Useable IF Bandwidth
BWIFPLL
Wireless Components
200
10.2
10.7
5 - 10
µV/
kHz
11.2
MHz
Data Sheet, December 2008
TDA7210
preliminary
Reference
Table 5-4 AC/DC Characteristics with TAMB= -40°C ... + 85°C, VCC = 4.5 ... 5.5 V
Parameter
Symbol
Limit Values
min
typ
Unit
max
Test Conditions /
L
Item
Notes
POWER DOWN MODE
Signal PDWN (PIN 27)
1
Powerdown Mode On
PWDNON
2.8
VCC
V
2
Powerdown Mode Off
PWDNOff
0
0.8
V
3
Start-up Time until valid
signal is detected at IF
TSU
<1
ms
depends on the
used crystal
VCO MULTIPLEXER
Signal FSEL (PIN 11)
1
fRF range 434 MHz
VFSEL
1.4
42
V
2
fRF range 869 MHz
VFSEL
0
0.2
V
3
Output bias current
FSEL
IFSEL
-110
-340
µA
FSEL tied to GND
or open
-200
or open
PLL DIVIDER
Signal CSEL (PIN 16)
1
fCRSTL range 6.xxMHz
VCSEL
1.4
42
V
2
fCRSTL range
13.xxMHz
VCSEL
0
0.2
V
3
Input bias current
CSEL
ICSEL
-3
-7
µA
-5
CSEL tied to GND
■ Not part of the production test - either verified by design or measured in an Infineon Evalboard as described in 2.
1) 2.8V is the voltage which is at least required that the LNA of a device is in high gain mode over the whole
RF-input level range. 3.3V is required that the LNA of each device is reliable in high gain mode over the whole
RF-input level range (considering also the production spread).
2) Maximum voltage in Power-On state is 4V, but in PDWN-state the maximum voltage is 2.8V.
Wireless Components
5 - 11
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.2 Test Circuit
The device performance parameters marked with ■ in 2 were either verified by
design or measured on an Infineon evaluation board. This evaluation board can
be obtained together with evaluation boards of the accompanying transmitter
device TDA7110 in an evaluation kit that may be ordered on the INFINEON
Webpage www.infineon.com. In case a matching codeword is received,
decoded and accepted by the decoder the on-board LED will turn on. This signal is also accessible on a 2-pole pin connector and can be used for simple
remote-control applications. More information on the kit is available on request.
TDA5210_testboard_20_schematic.WMF
Figure 5-1
Wireless Components
Schematic of the Evaluation Board
5 - 12
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.3 Test Board Layouts
tda5210_testboard_20_top.WMF
Figure 5-2
Top Side of the Evaluation Board
tda5210_testboard_20_bot.WMF
Figure 5-3
Wireless Components
Bottom Side of the Evaluation Board
5 - 13
Data Sheet, December 2008
TDA7210
preliminary
Reference
TDA7210
tda5210_testboard_20_plc.EMF
Figure 5-4
Wireless Components
Component Placement on the Evaluation Board
5 - 14
Data Sheet, December 2008
TDA7210
preliminary
Reference
5.4 Bill of Materials
The following components are necessary for evaluation of the TDA7210 without
use of a Microchip HCS512 decoder.
Table 5-5 Bill of Materials
Ref
Value
Specification
R1
100kΩ
0805, ± 5%
R2
100kΩ
0805, ± 5%
R3
820kΩ
0805, ± 5%
R4
240kΩ
0805, ± 5%
R5
360kΩ
0805, ± 5%
R6
10kΩ
0805, ± 5%
L1
434 MHz: 15nH
869 MHz: 3.3nH
Toko, PTL2012-F15N0G
Toko, PTL2012-F3N3C
L2
434 MHz: 8.2pF
869 MHz: 3.9nH
0805, COG, ± 0.1pF
Toko, PTL2012-F3N9C
C1
1pF
0805, COG, ± 0.1pF
C2
434 MHz: 4.7pF
869 MHz: 3.9pF
0805, COG, ± 0.1pF
0805, COG, ± 0.1pF
C3
434 MHz: 6.8pF
869 MHz: 5.6pF
0805, COG, ± 0.1pF
0805, COG, ± 0.1pF
C4
100pF
0805, COG, ± 5%
C5
47nF
1206, X7R, ± 10%
C6
434 MHz: 10nH
869 MHz: 3.9pF
Toko, PTL2012-F10N0G
0805, COG, ± 0.1pF
C7
100pF
0805, COG, ± 5%
C8
434 MHz: 33pF
869 MHz: 22pF
0805, COG, ± 5%
0805, COG, ± 5%
C9
100pF
0805, COG, ± 5%
C10
10nF
0805, X7R, ± 10%
C11
10nF
0805, X7R, ± 10%
C12
220pF
0805, COG, ± 5%
C13
47nF
0805, X7R, ± 10%
C14
470pF
0805, COG, ± 5%
C15
47nF
0805, X7R, ± 5%
C16
8.2pF
0805, COG, ± 0.1pF
C17
22pF
0805, COG, ± 1%
C18
22nF
0805, X7R, ± 5%
Q1
(fRF – 10.7MHz)/32 or
(fRF – 10.7MHz)/64
HC49/U, fundamental mode, CL = 12pF,
e.g. 434.2MHz: Jauch Q 13,23437-S11-1323-12-10/20
e.g. 868.4MHz: Jauch Q 13,40155-S11-1323-12-10/20
Wireless Components
5 - 15
Data Sheet, December 2008
TDA7210
preliminary
Reference
Q2
SFE10.7MA5-A or
SKM107M1-A20-10
Murata
Toko
X2, X3
142-0701-801
Johnson
S1-S3, S6
X1, X3
2-pole pin connector
S4
3-pole pin connector, or not equipped
IC1
TDA7210
Infineon
Please note that in case of operation at 434 MHz a capacitor has to be soldered
in place L2 and an inductor in place C6.
The following components are necessary in addition to the above mentioned
ones for evaluation of the TDA7210 in conjunction with a Microchip HCS512
decoder.
Table 5-6 Bill of Materials Addendum
Ref
Value
Specification
R7
100kΩ
0805, ± 5%
R8
10kΩ
0805, ± 5%
R9
100kΩ
0805, ± 5%
R10
22kΩ
0805, ± 5%
R11
100Ω
0805, ± 5%
R12
100Ω
0805, ± 5%
R13
100Ω
0805, ± 5%
R14
100Ω
0805, ± 5%
R21
22kΩ
0805, ± 5%
R22
10kΩ
0805, ± 5%
R23
22kΩ
0805, ± 5%
R24
820kΩ
0805, ± 5%
R25
560Ω
0805, ± 5%
C19
10pF
0805, COG, ± 5%
C21
100nF
1206, X7R, ± 10%
C22
100nF
1206, X7R, ± 10%
IC2
HCS512
Microchip
S5, X4-X9
2-pole pin connector
T1, T2
BC 847B
Infineon
D1
LS T670-JL
Infineon
Wireless Components
5 - 16
Data Sheet, December 2008
TDA7210
List of Figures
List of Figures
Figure 2-1
PG-TSSOP-28 package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3
Figure 3-1
IC Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2
Figure 3-2
Main Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9
Figure 4-1
LNA Automatic Gain Control Circuitry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2
Figure 4-2
RSSI Level and Permissive AGC Threshold Levels . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3
Figure 4-3
Data Filter Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4
Figure 4-4
Determination of Series Capacitance Value for the Quartz Oscillator . . . . . . . . . . . . . .
4-5
Figure 4-5
Data Slicer Threshold Generation with External R-C Integrator . . . . . . . . . . . . . . . . . .
4-7
Figure 4-6
Data Slicer Threshold Generation Utilising the Peak Detector . . . . . . . . . . . . . . . . . . .
4-7
Figure 4-7
ASK/FSK mode datapath . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8
Figure 4-8
Frequency characterstic in case of FSK mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9
Figure 4-9
Frequency charcteristic in case of ASK mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10
Figure 4-10 Principle of the precharge circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-11
Figure 4-11 Voltage appearing on C18 during precharging process . . . . . . . . . . . . . . . . . . . . . . . .
4-12
Figure 4-12 Voltage transient on capacitor C13 attached to pin 20 . . . . . . . . . . . . . . . . . . . . . . . . .
4-13
Figure 5-1
Schematic of the Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-12
Figure 5-2
Top Side of the Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-13
Figure 5-3
Bottom Side of the Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-13
Figure 5-4
Component Placement on the Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-14
Wireless Components
List of Figures - 1
Data Sheet, December 2008
TDA7210
List of Tables
List of Tables
Table 3-1
Pin Definition and Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3
Table 3-2
FSEL Pin Operating States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11
Table 3-3
CSEL Pin Operating States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11
Table 3-4
MSEL Pin Operating States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-12
Table 3-5
PDWN Pin Operating States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-13
Table 4-1
Dependence of PLL Overall Division Ratio on FSEL and CSEL . . . . . . . . . . . . . . . . .
4-6
Table 5-1
Absolute Maximum Ratings, Ambient temperature TAMB=-40°C ... + 85°C . . . . . . . . .
5-2
Table 5-2
Operating Range, Ambient temperature TAMB= -40°C ... + 85°C . . . . . . . . . . . . . . . . .
5-3
Table 5-3
AC/DC Characteristics with TA 25 °C, VCC = 4.5 ... 5.5 V . . . . . . . . . . . . . . . . . . . . . .
5-4
Table 5-4
AC/DC Characteristics with TAMB= -40°C ... + 85°C, VCC = 4.5 ... 5.5 V . . . . . . . . . . .
5-9
Table 5-5
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-15
Table 5-6
Bill of Materials Addendum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-16
Wireless Components
List of Tables - 1
Data Sheet, December 2008