Download

CSI-8H8CV2IR
8 HDMI over CAT6 Point-to-Point Transmitter
(with IR Matrix)
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
VR0
11/07/12
Preliminary Release
VR1
17/02/13
Add CAT5e/6/7 Cable Spec.
CONTENTS
1. Introduction���������������������������������������������������������������1
2. Applications��������������������������������������������������������������1
3. Package Contents���������������������������������������������������1
4. System Requirements�����������������������������������������������1
5. Features���������������������������������������������������������������������2
6. Operation Controls and Functions��������������������������3
6.1 Front Panel���������������������������������������������������������3
6.2 Rear Panel����������������������������������������������������������4
6.3 Remote Control for IR Matrix����������������������������5
6.4 IR Custom Code������������������������������������������������5
6.5 Discrete IR Codes����������������������������������������������6
6.6 IR Dip Switch Position with Output Selection�6
6.7 IR Cable Pin Assignment����������������������������������7
6.8 RS-232 Pin Assignments�������������������������������������8
6.9 RS-232 Commands for IR Matrix�����������������������9
7. Connection Diagram���������������������������������������������11
8. Specifications���������������������������������������������������������13
9. Acronyms����������������������������������������������������������������14
1. INTRODUCTION
The 8 HDMI over CAT6 Point-to-Point Transmitter (with IR Matrix)
supports the transmission of Video (up to 1080p Full HD/1920×1200@60
Hz) with multichannel digital audio, up to eight pairs of high definition
source and CAT5e/6 output. It supports digital audio formats such
as LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Mater
Audio. 3D content can be displayed when connecting a 3DTV and 3D
source. The Transmitter allows the point-to-point connection between
source equipment and output display, over distances up to 100
meters along with PoE (Power over Ethernet) feature. There is a builtin crosspoint IR matrix providing additional control over 8-in-8-out IR
channels.
2. APPLICATIONS
• Commercial advertising and display
• Lecture room display and control
• Hyper market demonstration and control
• Any Smart AV Installation
3. PACKAGE CONTENTS
• HDMI over CAT6 Transmitter with 8×8 IR Matrix
• 8×Receiver for HDMI over CAT6 (Optional)
• 2×IR Extender
• 2×IR Blaster
• 24 V/6.25 A DC Adaptor
• Remote Control with 3V battery
• Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI equipped input source devices with HDMI cables
• HDMI equipped output displays (TVs or monitors) or HDMI equipped
AV receivers with HDMI cables
• Industry standard CAT5e/6/7 cables
1
5. FEATURES
• HDMI, HDCP1.1 and DVI compliant
• Supports HDMI 3D, 4k x 2k features
• Supports Stereo digital audio signal input and output
• Supports high bit-rate audio up to 192 kHz
• Supports resolutions VGA~WUXGA and 480i~1080p dependent upon
the output display’s EDID settings
• Supports extension up to 100 meters through CAT5e/6
• Supports 3D signal display dependent upon the output display's
EDID settings
• Supports HDMI input up to 10 meters at 8-bit resolution or 3 meters at
12-bit resolution
• Supports bi-directional IR from input and output locations
• Supports RS-232, remote control and on-panel control
• Supports PoE (Power over Ethernet) on compatible receivers only
• 2U size design
Note: The PoE function is designed for powering compatible receiver
units only—non-PoE receivers will need their own power supply.
Receivers of another brand may not be compatible.
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
8 HDMI Over CAT6 Transmitter w/IR Matrix
1
2
3
4
5
6
7
8
IR
1
2
Power
All
Lock
Enter
3
4
5
6
7
1 LCM: Displays the information for each IR input and output setting.
2 IR: IR Receiver window (accepts the remote control signal of this
device and all output displays or source devices).
3 Power: Press this button to power the device on/off. The LED will
illuminate green when the power is on, red when it is in 'Standby'
mode.
4 All: Press this button to select all IR output with one IR input signal.
The sequence should be pressed ALL → Number Key → ENTER.
5 Lock: Press this button to lock all the buttons on the panel; press
again to unlock. The LED will illuminate in green when locked.
6 Enter: Press this button to confirm when changing a setting.
7 Selection 1~8
3
When selecting the IR input for a specific IR output, press the
Number Key first to select the output and then press the Number
Key again to select the input.
6.2 Rear Panel
3
1
2
3
RS232
AUX
4
5
IR Blaster
6
7
8
4
6
All
IR Extender
GND
RS232
MAIN
GND
2
1
4
3
V+
V+
GND
CAT Out
CAT Out
HDMI In 1
1
2
CAT Out
HDMI In 2
CAT Out
HDMI In 3
CAT Out
HDMI In 4
CAT Out
HDMI In 5
HDMI In 6
DC 24V
CAT Out
CAT Out
HDMI In 7
HDMI In 8
5
7
1 RS-232 AUX: Connect to a device that can be controlled (via D-Sub
9-pin male cable) by RS-232 commands.
2 RS-232 MAIN: Connect to a PC or laptop with D-Sub 9-pin male
cable for the transmission of RS-232 commands.
3 IR Blaster 1~All: Connect the supplied IR blasters (included in the
package) for IR signal transmission, IR signals will be relayed from the
designated output IR extender. For the "All" port, the IR signals will be
relayed from all output at the same time. Place the IR blaster in direct
line-of-sight of the equipment to be controlled.
4 IR Extender 1~All: Connect the supplied IR extenders (included in
the package) for IR signal reception the signal will be relayed to the
designated output device via the IR blaster. For the "All" port, the
signal will be relayed to all outputs. Ensure that remote being used is
within the direct line-of-sight of the IR extender.
5 HDMI In 1~8: Connect to the HDMI input source devices such as a
DVD player or a Set-top Box with HDMI cables or DVI to HDMI cables.
6 CAT Out 1~8: Connect to the CAT in port of receiver units with a
single CAT5e/6/7 cable for HDMI Audio/Video and IR/RS-232 control
signal sending.
Note: Do NOT connect these CAT outputs to the LAN port of
receiver units—this will cause serious damage to the receiver unit.
7 DC 24V: Plug the 24 V DC power supply (included in the package)
into the unit and connect the adaptor to an AC outlet. This unit will
also power PoE (Power over Ethernet) capable receiver units.
4
6.3 Remote Control for IR Matrix
The remote control unit included in the package is
for IR Matrix only, and can be used to control the
IR channel mapping of individual or all receivers,
depends on the dipswitch setting.
There are total of four dipswitches, when all of
them are set to ON/↑, the remote control unit is
able to control the IR routing of all receivers. For
example, if you want to set up the bi-directional IR
channel between Output A receiver and Input 5,
simply press A first and then press 5.
1
A
2
B
3
C
4
D
5
E
6
F
7
G
8
H
IN
OUT
You can set the remote control unit to control the
IR routing of single receiver only, please refer to
the dipswitch settings in section 6.6. For example,
CR-110
when all dipswitches are set to OFF/↓, only the IR
channel of Output A receiver can be selected,
when you want to set up the bi-directional IR channel between
Output A receiver and Input 3, simply press 3.
6.4 IR Custom Code
5
NO.
DATA
NO.
DATA
1
88
A
8A
2
8C
B
8E
3
90
C
92
4
85
D
C6
5
C2
E
99
6
9C
F
98
7
D8
G
84
8
87
H
97
6.5 Discrete IR Codes
Select /
Custom
Dipswitch
Code
output A ↓↓↓↓
807F
output B ↑↓↓↓
807B
output C ↓↑↓↓
8077
output D ↑↑↓↓
8073
output E ↓↓↑↓
803F
output F ↑↓↑↓
803B
output G ↓↑↑↓
8037
output H ↑↑↑↓
8033
6.6 IR Dip Switch Position with Output Selection
Selects
Selects
OUTPUT A
OUTPUT E
Selects
Selects
OUTPUT B
OUTPUT F
Selects
Selects
OUTPUT C
OUTPUT G
Selects
Selects
OUTPUT D
OUTPUT H
6
6.7 IR Cable Pin Assignment
IR Blaster
1 Power 5 V
2 IR Blaster Signal
3 NC
IR Receiver
1 IR Signal
2 Power 5 V
3 Grounding
7
6.8 RS-232 Pin Assignments
CSI-8H8CV2IR
Remote Control Console
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
TX
2
RX
3
RX
3
TX
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
Baud Rate: 19200 bps/A or 9600/B
Data bit: 8-bit
Parity: None
Stop bit: 1-bit
Flow Control: None
8
6.9 RS-232 Commands for IR Matrix
Command A
Description
A1~A8
Switch Output A to 1~8
B1~B8
Switch Output B to 1~8
C1~C8
Switch Output C to 1~8
D1~D8
Switch Output D to 1~8
E1~E8
Switch Output E to 1~8
F1~F8
Switch Output F to 1~8
G1~G8
Switch Output G to 1~8
H1~H8
Switch Output H to 1~8
ABCD...1~ABCD...8
Switch Output A B C D... to 1~8 at the same
time
P0
Power OFF
P1
Power ON
I1~I8
Switch all the Output to 1~8
ST
Display the current matrix status and F/W version
RS
System reset to A1, B2, C3, D4, E5, F6, G7, H8
?
Display all available commands
Note: 1. Press "ALL" + "ENTER" +"1" buttons all together from the panel to switch RS-232 to A and the LCM will display baud rate 19200bps.
2.Command "RS" will reset output A~H to 1~8 and shut down the device automatically.
9
Command B
Description
POWER 00
Power Off (Standby)
POWER 01
Power On
PORT 11~18
Output A select Input1~8
PORT 21~28
Output B select Input1~8
PORT 31~38
Output C select Input1~8
PORT 41~48
Output D select Input1~8
PORT 51~58
Output E select Input1~8
PORT 61~68
Output F select Input1~8
PORT 71~78
Output G select Input1~8
PORT 81~88
Output H select Input1~8
Note: 1.Press "ALL" + "ENTER" +"2" buttons all together from the panel to switch RS-232 to B and the LCM will display baud rate 9600bps.
2.All the commands will not be executed unless followed with a carriage return. All letters are not case-sensitive.
10
7. CONNECTION DIAGRAM
ZONE A
ZONE B
ZONE C
ZONE E
ZONE D
Displays
HDMI Outputs
IR Out/In
Receiver Units
RX
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
RX
Power
RX
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Power
RX
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Power
RX
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5
Single
CAT 5e/6
Cable
RS-232 Equipped
PC or Notebook
1
2
3
4
RS232
AUX
5
IR Blaster
6
7
8
All
IR Extender
GND
RS232
MAIN
GND
2
1
4
3
V+
T
V+
GND
CAT Out
CAT Out
HDMI In 1
CAT Out
HDMI In 2
CAT Out
HDMI In 3
CAT Out
HDMI In 4
CAT Out
HDMI In 5
HDMI In 6
DC 24V
CAT Out
CAT Out
HDMI In 7
HDMI In 8
RS-232
8x8
A
HDMI Out
LAN
B
HDMI Out
C
HDMI Out
D
HDMI Out
E
HDMI Out
F
HDMI Out
G
HDMI Out
H
HDMI Out
IR-In
V+
GND
RS-232
HDMI
Inputs
Source
Equipment
11
GND
3
4
1
2
Service
1
HDMI In
2
HDMI In
3
HDMI In
4
HDMI In
5
HDMI In
6
HDMI In
7
HDMI In
8
HDMI In
1
2
3
4
5
6
7
8
DC 24V
V+
GND
5e/6 In
ZONE F
RX
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
ZONE G
RX
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
ZONE H
RX
Power
Link
IR 2
IR 1
Extender Blaster
RS232 Out
CAT5e/6 In
Transmitter
Power Supply
HDMI
Outputs
IR Out/In
1.5m
60°
8 HDMI Matrix
IR BLASTER
60°
3m
7m
m
3m
IR RECEIVER
Power Supply
IR Out (All)
IR In (ALL)
12
8. SPECIFICATIONS
Video Bandwidth
300 MHz/10.2 Gbps
Input Ports
8×HDMI, 9×IR Extender, 1×RS-232
Output Ports
8×CAT5e/6/7, 9×IR Blaster, 1×RS-232
Input/Output Resolution
VGA~WUXGA, 480i~1080p@24/50/60,
4kx2k@24/25/30
ESD Protection
Human-body Model:
±8 kV (Air-gap discharge)
±4 kV (Contact discharge)
Power Supply
24 V/6.25 A DC (US/EU standards, CE/FCC/
UL certified)
Dimensions
432 mm (W)×210 mm (D)×93 mm (H)
Weight
3312 g Chassis Material
Metal
Silkscreen Color
Black
Operating Temperature
0 ºC~40 ºC/32 ºF~104 ºF
Storage Temerature
−20 ºC~60 ºC/−4 ºF~140 ºF
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
90 W (Including Transmitter)
CAT5e/6/7 Cable Specification
Cable
Range Pixel clock
Type
rate
CAT5e/6/7 100 m
Video Data
Supported Video
Rate
<=225 MHz <=5.3 Gbps Up to 1080p, 60 Hz,
(HD Video) 36 bits, 3D (data
rates lower than 5.3
Gbps or below 225
MHz TMDS clock).
70 m
>225 MHz
> 5.3 Gbps
4K2K, 30Hz video
(Ultra HD
formats
Video)
13
9. ACRONYMS
ACRONYM
COMPLETE TERM
DTS
Digital Theater System
DVI
Digital Visual Interface
EDID
Extended Display Identification Data
HDCP
High-bandwidth Digital Content Protection
HDMI
High-Definition Multimedia Interface
LCM
Liquid Crystal Module
USB
Universal Serial Bus
VGA
Video Graphics Array
WUXGA
Widescreen Ultra Extended Graphics Array
14
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20120620 MPM-CSI8H8CV2IR