ESIG WD E ® N FOR 63 DED 0, EL52 N E OMM L526 R EC SEE E T Data Sheet O N NS Dual 600MHz Current Feedback Amplifier with Enable The EL5292 and EL5292A represent dual current feedback amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for today’s high speed video and monitor applications. With a supply current of just 6mA per amplifier and the ability to run from a single supply voltage from 5V to 10V, these amplifiers are also ideal for hand held, portable or battery powered equipment. EL5292, EL5292A June 28, 2007 FN7192.1 Features • 600MHz -3dB bandwidth • 6mA supply current (per amplifier) • Single and dual supply operation, from 5V to 10V • Fast enable/disable (EL5292A only) • Single (EL5192) and triple (EL5392) available • High speed, 1GHz product available (EL5191) • Low power, 4mA, 300MHz product available (EL5193, EL5293, and EL5393) The EL5292A also incorporates an enable and disable function to reduce the supply current to 100µA typical per amplifier. Allowing the CE pin to float or applying a low logic level will enable the amplifier. Applications The EL5292 is offered in the industry-standard 8 Ld SOIC package and the space-saving 8 Ld MSOP package. The EL5292A is available in a 10 Ld MSOP package and all operate over the industrial temperature range of -40°C to +85°C. • RGB amplifiers • Video amplifiers • Cable drivers • Test equipment • Instrumentation • Current to voltage converters Pinouts Ordering Information EL5292 (8 LD SOIC) TOP VIEW OUTA 1 INA- 2 + INA+ 3 + VS- 4 PART NUMBER PKG. DWG. # EL5292CS 5292CS 8 Ld SOIC MDP0027 7 OUTB EL5292CS-T7* 5292CS 8 Ld SOIC MDP0027 6 INB- EL5292CS-T13* 5292CS 8 Ld SOIC MDP0027 EL5292ACY T 10 Ld MSOP MDP0043 EL5292ACY-T7* T 10 Ld MSOP MDP0043 EL5292ACY-T13* T 10 Ld MSOP MDP0043 5 INB+ *“-T7” or “-T13” suffix is for tape and reel. Please refer to TB347 for details on reel specifications. 10 INA- INA+ 1 + 9 OUTA 8 VS+ VS- 3 CEB 4 PACKAGE 8 VS+ EL5292A (10 LD MSOP) TOP VIEW CEA 2 PART MARKING + - 7 OUTB 6 INB- INB+ 5 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2004, 2007. All Rights Reserved Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL5292, EL5292A Absolute Maximum Ratings (TA = +25°C) Thermal Information Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . . . 11V Pin Voltages . . . . . . . . . . . . . . . . . . . . . . . . . VS- -0.5V to VS+ +0.5V Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. Electrical Specifications PARAMETER VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 375Ω for AV = 2, RL = 150Ω, TA = +25°C unless otherwise specified. DESCRIPTION CONDITIONS MIN (Note 2) TYP MAX (Note 2) UNIT AC PERFORMACE BW -3dB Bandwidth AV = +1 600 MHz AV = +2 300 MHz 25 MHz 2300 V/µs BW1 0.1dB Bandwidth SR Slew Rate VO = -2.5V to +2.5V, AV = +2 tS 0.1% Settling Time VOUT = -2.5V to +2.5V, AV = -1 9 ns CS Channel Separation f = 5MHz 60 dB eN Input Voltage Noise 4.1 nV/√Hz iN- IN- Input Current Noise 20 pA/√Hz iN+ IN+ Input Current Noise 50 pA/√Hz dG Differential Gain Error (Note 1) AV = +2 0.015 % dP Differential Phase Error (Note 1) AV = +2 0.04 ° 2000 DC PERFORMANCE VOS Offset Voltage TCVOS Input Offset Voltage Temperature Coefficient Measured from TMIN to TMAX ROL Transimpediance -10 1 10 mV 5 µV/°C 200 400 kΩ INPUT CHARACTERISTICS CMIR Common Mode Input Range ±3 ±3.3 V CMRR Common Mode Rejection Ratio 42 50 dB +IIN + Input Current -60 3 60 µA -IIN - Input Current -35 4 35 µA RIN Input Resistance 37 kΩ CIN Input Capacitance 0.5 pF OUTPUT CHARACTERISTICS VO RL = 150Ω to GND ±3.4 ±3.7 V RL = 1kΩ to GND ±3.8 ±4.0 V Output Current RL = 10Ω to GND 95 120 mA ISON Supply Current - Enabled No load, VIN = 0V 5 6 7.5 mA ISOFF Supply Current - Disabled No load, VIN = 0V 100 150 µA PSRR Power Supply Rejection Ratio DC, VS = ±4.75V to ±5.25V IOUT Output Voltage Swing SUPPLY 2 55 75 dB FN7192.1 June 28, 2007 EL5292, EL5292A Electrical Specifications PARAMETER -IPSR VS+ = +5V, VS- = -5V, RF = 750Ω for AV = 1, RF = 375Ω for AV = 2, RL = 150Ω, TA = +25°C unless otherwise specified. (Continued) DESCRIPTION - Input Current Power Supply Rejection CONDITIONS DC, VS = ±4.75 to ±5.25V MIN (Note 2) TYP -2 MAX (Note 2) UNIT 2 µA/V ENABLE (EL5292A Only) tEN Enable Time 40 ns tDIS Disable Time 600 ns IIHCE CE Pin Input High Current CE = VS+ 0.8 6 µA IILCE CE Pin Input Low Current CE = VS- 0 -0.1 µA VIHCE CE Input High Voltage for Power-down VILCE CE Input Low Voltage for Power-down VS+ - 1 V VS+ - 3 V NOTE: 1. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz 2. Parts are 100% tested at +25°C. Over temperature limits established by characterization and are not production tested. 3 FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves Non-Inverting Frequency Response (Gain) Non-Inverting Frequency Response (Phase) 6 90 AV=2 0 -2 -90 AV=1 AV=2 Phase (°) Normalized Magnitude (dB) AV=1 2 AV=5 -6 AV=5 AV=10 -180 AV=10 -10 -270 -14 1M RF=750Ω RL=150Ω 10M 100M -360 1M 1G RF=750Ω RL=150Ω 10M Frequency (Hz) Inverting Frequency Response (Gain) 90 AV=-1 2 AV=-2 AV=-1 0 Phase (°) -2 AV=-5 -6 -10 -90 AV=-2 AV=-5 -180 -270 -14 1M RF=375Ω RL=150Ω 10M 100M -360 1M 1G RF=375Ω RL=150Ω 10M Frequency (Hz) 100M Frequency Response for Various CIN- Frequency Response for Various RL 6 RL=150Ω Normalized Magnitude (dB) 2pF added 6 1pF added 2 -2 -6 -10 1M 1G Frequency (Hz) 10 Normalized Magnitude (dB) 1G Inverting Frequency Response (Phase) 6 Normalized Magnitude (dB) 100M Frequency (Hz) 0pF added AV=2 RF=375Ω RL=150Ω 10M 100M Frequency (Hz) 4 1G RL=100Ω 2 RL=500Ω -2 -6 -10 -14 1M AV=2 RF=375Ω 10M 100M 1G Frequency (Hz) FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Frequency Response for Various CL Frequency Response for Various RF 14 6 Normalized Magnitude (dB) Normalized Magnitude (dB) 250Ω 10 12pF added 6 8pF added 2 -2 -6 1M 0pF added AV=2 RF=375Ω RL=150Ω 10M 100M 475Ω -2 620Ω -6 750Ω -10 -14 1M 1G AV=2 RG=RF RL=150Ω 10M Frequency (Hz) 100M 1G Frequency (Hz) Group Delay vs Frequency Frequency Response for Various Common-Mode Input Voltages 3.5 6 2.5 Normalized Magnitude (dB) 3 Group Delay (ns) 375Ω 2 AV=2 RF=375Ω 2 1.5 1 AV=1 RF=750Ω 0.5 0 1M 10M 100M VCM=3V -2 VCM=-3V -6 -10 -14 1M 1G VCM=0V 2 AV=2 RF=375Ω RL=150Ω 10M Frequency (Hz) 100M 1G Frequency (Hz) Transimpedance (ROL) vs Frequency PSRR and CMRR vs Frequency 10M 20 0 Phase 100k -180 10k -270 Gain 1k PSRR/CMRR (dB) 0 -90 Phase (°) Magnitude (Ω) 1M PSRR+ -20 PSRR-40 -60 CMRR -360 100 1k 10k 100k 1M 10M Frequency (Hz) 5 100M 1G -80 10k 100k 1M 10M Frequency (Hz) 100M 1G FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) -3dB Bandwidth vs Supply Voltage for NonInverting Gains -3dB Bandwidth vs Supply Voltage for Inverting Gains 350 RF=750Ω RL=150Ω 300 600 -3dB Bandwidth (MHz) -3dB Bandwidth (MHz) 800 AV=1 400 AV=2 200 AV=5 AV=10 AV=-1 250 AV=-2 200 AV=-5 150 100 50 0 RF=375Ω RL=150Ω 0 5 6 7 8 9 10 5 6 Total Supply Voltage (V) Peaking vs Supply Voltage for Non-Inverting Gains 4 3 Peaking (dB) Peaking (dB) 10 RF=375Ω RL=150Ω AV=-1 2 AV=-2 2 1 AV=2 AV=10 AV=-5 0 0 5 6 7 8 9 10 5 Total Supply Voltage (V) 1000 800 600 400 AV=2 AV=5 8 9 10 -3dB Bandwidth vs Temperature for Inverting Gains RF=750Ω RL=150Ω AV=1 7 500 -3dB Bandwidth (MHz) 1200 6 Total Supply Voltage (V) -3dB Bandwidth vs Temperature for Non-Inverting Gains 1400 -3dB Bandwidth (MHz) 9 Peaking vs Supply Voltage for Inverting Gains AV=1 1 8 4 RF=750Ω RL=150Ω 3 7 Total Supply Voltage (V) AV=10 400 300 RF=375Ω RL=150Ω AV=-1 AV=-2 200 AV=-5 100 200 0 -40 10 60 110 Ambient Temperature (°C) 6 160 0 -40 10 60 110 160 Ambient Temperature (°C) FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Peaking vs Temperature 2 Voltage Noise (nV/√Hz) Current Noise (pA/√Hz) RL=150Ω 1.5 Peaking (dB) Voltage and Current Noise vs Frequency 1k AV=1 1 AV=-1 0.5 AV=-2 0 100 i n+ in- 10 en AV=2 -0.5 -50 -50 0 50 1 100 100 1k Ambient Temperature (°C) 10 10 8 1 0.1 0.01 0.001 10M 6 4 2 0 100 1k 10k 100k 1M 10M Frequency (Hz) 100M 1G 0 2nd and 3rd Harmonic Distortion vs Frequency -20 -50 2nd Order Distortion -60 -70 3rd Order Distortion -80 -90 -100 1 10 Frequency (MHz) 7 4 6 8 Supply Voltage (V) 10 12 Two-Tone 3rd Order Input Referred Intermodulation Intercept (IIP3) Input Power Intercept (dBm) -40 2 30 AV=+2 VOUT=2VP-P RL=100Ω -30 Harmonic Distortion (dBc) 1M Supply Current vs Supply Voltage 100 Supply Current (mA) Output Impedance (Ω) Closed Loop Output Impedance vs Frequency 10k 100k Frequency (Hz) 100 AV=+2 RL=150Ω 25 20 15 10 5 0 -5 -10 -15 10 AV=+2 RL=100Ω 100 200 Frequency (MHz) FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Differential Gain/Phase vs DC Input Voltage at 3.58MHz AV=2 RF=RG=375Ω RL=150Ω 0.02 dG (%) or dP (°) 0.01 Differential Gain/Phase vs DC Input Voltage at 3.58MHz 0.03 dP 0.01 0 dG -0.01 -0.02 0 -0.03 -0.04 -0.05 0 0.5 dG -0.02 -0.04 -0.5 -0.06 -1 1 dP -0.01 -0.03 -0.05 -1 AV=1 RF=750Ω RL=500Ω 0.02 dG (%) or dP (°) 0.03 -0.5 DC Input Voltage Output Voltage Swing vs Frequency THD<1% 0.5 1 Output Voltage Swing vs Frequency THD<0.1% 9 10 RL=500Ω 8 7 Output Voltage Swing (VPP) Output Voltage Swing (VPP) 0 DC Input Voltage RL=150Ω 6 5 4 3 2 1 AV=2 0 RL=500Ω 8 RL=150Ω 6 4 2 AV=2 0 1 10 Frequency (MHz) 100 1 Small Signal Step Response 10 Frequency (MHz) Large Signal Step Response VS=±5V RL=150Ω AV=2 RF=RG=375Ω 200mV/div 100 VS=±5V RL=150Ω AV=2 RF=RG=375Ω 1V/div 10ns/div 8 10ns/div FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Settling Time vs Settling Accuracy 25 AV=2 RF=RG=375Ω RL=150Ω VSTEP=5VP-P output 20 450 15 RoI (kΩ) Settling Time (ns) Transimpedance (RoI) vs Temperature 500 10 400 350 5 0 0.01 0.1 300 -40 1 10 PSRR and CMRR vs Temperature 110 160 110 160 ICMR and IPSR vs Temperature 90 2.5 80 PSRR 2 ICMR/IPSR (µA/V) 70 PSRR/CMRR (dB) 60 Die Temperature (°C) Settling Accuracy (%) 60 CMRR 50 40 30 ICMR+ 1.5 1 IPSR 0.5 0 ICMR- -0.5 20 10 -40 10 60 110 -1 -40 160 10 Die Temperature (°C) 60 Die Temperature (°C) Offset Voltage vs Temperature Input Current vs Temperature 3 60 40 Input Current (µA) VOS (mV) 2 1 0 20 IB0 -20 IB+ -40 -1 -60 -2 -40 10 60 Die Temperature (°C) 9 110 160 -80 -40 10 60 110 160 Temperature (°C) FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Positive Input Resistance vs Temperature Supply Current vs Temperature 50 8 45 7 Supply Current (mA) 40 RIN+ (kΩ) 35 30 25 20 15 10 6 5 4 3 2 1 5 0 -40 10 60 110 0 -40 160 10 60 Temperature (°C) 110 160 Temperature (°C) Positive Output Swing vs Temperature for Various Loads Negative Output Swing vs Temperature for Various Loads 4.2 -3.5 4.1 -3.6 150Ω 1kΩ -3.7 VOUT (V) VOUT (V) 4 3.9 3.8 3.7 -3.8 -3.9 1kΩ -4 150Ω 3.6 -4.1 3.5 -40 10 50 110 -4.2 -40 160 10 60 Temperature (°C) 110 160 110 160 Temperature (°C) Output Current vs Temperature Slew Rate vs Temperature 135 4600 4400 4200 Sink Slew Rate (V/µS) IOUT (mA) 130 125 Source 120 4000 3800 3600 3400 3200 115 -40 10 60 Die Temperature (°C) 10 110 160 3000 -40 AV=2 RF=RG=375Ω RL=150Ω 10 60 Die Temperature (°C) FN7192.1 June 28, 2007 EL5292, EL5292A Typical Performance Curves (Continued) Channel-to-Channel Isolation vs Frequency Enable Response 0 Gain (dB) -20 500mV/div -40 -60 5V/div -80 -100 100k 1M 10M 100M 400M 20ns/div Frequency (Hz) Package Power Dissipation vs Ambient Temperature JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board Disable Response 0.7 500mV/div 8 SO C/W 0° 16 Power Dissipation (W) 0.6 625mW 0.5 0.4 0.3 0.2 0.1 5V/div 0 0 400ns/div 25 50 75 85 100 125 150 Ambient Temperature (°C) 0.6 Package Power Dissipation vs Ambient Temperature JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board 486mW Power Dissipation (W) 0.5 M SO P8 20 /1 0 6° C/ W 0.4 0.3 0.2 0.1 0 0 25 50 75 85 100 125 Ambient Temperature (°C) 11 FN7192.1 June 28, 2007 EL5292, EL5292A Pin Descriptions 8 LD SOIC/MSOP 10 LD MSOP 1 9 PIN NAME OUTA FUNCTION EQUIVALENT CIRCUIT Output, channel A VS+ OUT VSCircuit 1 2 10 INA- Inverting input, channel A VS+ IN- IN+ VSCircuit 2 3 1 INA+ Non-inverting input, channel A 2 CEA Chip enable, channel A (see circuit 2) VS+ CE VSCircuit 3 4 3 VS- Negative supply 4 CEB Chip enable, channel B (see circuit 3) 5 5 INB+ Non-inverting input, channel B (see circuit 2) 6 6 INB- Inverting input, channel B (see circuit 2) 7 7 OUTB Output, channel B (see circuit 1) 8 8 VS+ Positive supply Applications Information Product Description The EL5292 is a current-feedback operational amplifier that offers a wide -3dB bandwidth of 600MHz and a low supply current of 6mA per amplifier. The EL5292 works with supply voltages ranging from a single 5V to 10V and they are also capable of swinging to within 1V of either supply on the output. Because of their current-feedback topology, the EL5292 does not have the normal gain-bandwidth product associated with voltage-feedback operational amplifiers. Instead, its -3dB bandwidth to remain relatively constant as closed-loop gain is increased. This combination of high bandwidth and low power, together with aggressive pricing make the EL5292 the ideal choice for many low-power/highbandwidth applications such as portable, handheld, or battery-powered equipment. 12 For varying bandwidth needs, consider the EL5191 with 1GHz on a 9mA supply current or the EL5193 with 300MHz on a 4mA supply current. Versions include single, dual, and triple amp packages with 5 Ld SOT23, 16 Ld QSOP, and 8 Ld or 16 Ld SOIC outlines. Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, good printed circuit board layout is necessary for optimum performance. Low impedance ground plane construction is essential. Surface mount components are recommended, but if leaded components are used, lead lengths should be as short as possible. The power supply pins must be well bypassed to reduce the risk of oscillation. The combination of a 4.7µF tantalum capacitor in parallel with a 0.01µF capacitor has been shown to work well when placed at each supply pin. FN7192.1 June 28, 2007 EL5292, EL5292A For good AC performance, parasitic capacitance should be kept to a minimum, especially at the inverting input. (See the Capacitance at the Inverting Input section) Even when ground plane construction is used, it should be removed from the area near the inverting input to minimize any stray capacitance at that node. Carbon or Metal-Film resistors are acceptable with the Metal-Film resistors giving slightly less peaking and bandwidth because of additional series inductance. Use of sockets, particularly for the SOIC package, should be avoided if possible. Sockets add parasitic inductance and capacitance which will result in additional peaking and overshoot. Disable/Power-Down The EL5292A amplifier can be disabled placing its output in a high impedance state. When disabled, the amplifier supply current is reduced to < 300µA. The EL5292A is disabled when its CE pin is pulled up to within 1V of the positive supply. Similarly, the amplifier is enabled by floating or pulling its CE pin to at least 3V below the positive supply. For ±5V supply, this means that an EL5292A amplifier will be enabled when CE is 2V or less, and disabled when CE is above 4V. Although the logic levels are not standard TTL, this choice of logic voltages allows the EL5292A to be enabled by tying CE to ground, even in 5V single supply applications. The CE pin can be driven from CMOS outputs. Capacitance at the Inverting Input Any manufacturer’s high-speed voltage- or current-feedback amplifier can be affected by stray capacitance at the inverting input. For inverting gains, this parasitic capacitance has little effect because the inverting input is a virtual ground, but for non-inverting gains, this capacitance (in conjunction with the feedback and gain resistors) creates a pole in the feedback path of the amplifier. This pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop response. The use of largevalue feedback and gain resistors exacerbates the problem by further lowering the pole frequency (increasing the possibility of oscillation.) The EL5292 has been optimized with a 375Ω feedback resistor. With the high bandwidth of these amplifiers, these resistor values might cause stability problems when combined with parasitic capacitance, thus ground plane is not recommended around the inverting input pin of the amplifier. Feedback Resistor Values The EL5292 has been designed and specified at a gain of +2 with RF approximately 375Ω. This value of feedback resistor gives 300MHz of -3dB bandwidth at AV = 2 with 2dB of peaking. With AV = -2, an RF of 375Ω gives 275MHz of bandwidth with 1dB of peaking. Since the EL5292 is a current-feedback amplifier, it is also possible to change the value of RF to get more bandwidth. As seen in the curve of Frequency Response for Various RF and RG, bandwidth and 13 peaking can be easily modified by varying the value of the feedback resistor. Because the EL5292 is a current-feedback amplifier, its gain-bandwidth product is not a constant for different closedloop gains. This feature actually allows the EL5292 to maintain about the same -3dB bandwidth. As gain is increased, bandwidth decreases slightly while stability increases. Since the loop stability is improving with higher closed-loop gains, it becomes possible to reduce the value of RF below the specified 375Ω and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. Supply Voltage Range and Single-Supply Operation The EL5292 has been designed to operate with supply voltages having a span of greater than 5V and less than 10V. In practical terms, this means that the EL5292 will operate on dual supplies ranging from ±2.5V to ±5V. With singlesupply, the EL5292 will operate from 5V to 10V. As supply voltages continue to decrease, it becomes necessary to provide input and output voltage ranges that can get as close as possible to the supply voltages. The EL5292 has an input range which extends to within 2V of either supply. So, for example, on ±5V supplies, the EL5292 has an input range which spans ±3V. The output range of the EL5292 is also quite large, extending to within 1V of the supply rail. On a ±5V supply, the output is therefore capable of swinging from--4V to +4V. Single-supply output range is larger because of the increased negative swing due to the external pull-down resistor to ground. Video Performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult when driving a standard video load of 150Ω, because of the change in output current with DC level. Previously, good differential gain could only be achieved by running high idle currents through the output transistors (to reduce variations in output impedance.) These currents were typically comparable to the entire 6mA supply current of each EL5292 amplifier. Special circuitry has been incorporated in the EL5292 to reduce the variation of output impedance with current output. This results in dG and dP specifications of 0.015% and 0.04°, while driving 150Ω at a gain of 2. Video performance has also been measured with a 500Ω load at a gain of +1. Under these conditions, the EL5292 has dG and dP specifications of 0.03% and 0.05°, respectively. Output Drive Capability In spite of its low 6mA of supply current, the EL5292 is capable of providing a minimum of ±95mA of output current. With a minimum of ±95mA of output drive, the EL5292 is FN7192.1 June 28, 2007 EL5292, EL5292A capable of driving 50Ω loads to both rails, making it an excellent choice for driving isolation transformers in telecommunications applications. Driving Cables and Capacitive Loads When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, the back-termination series resistor will decouple the EL5292 from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. In these applications, a small series resistor (usually between 5Ω and 50Ω) can be placed in series with the output to eliminate most peaking. The gain resistor (RG) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output. In many cases it is also possible to simply increase the value of the feedback resistor (RF) to reduce the peaking. important to calculate the maximum junction temperature (TJMAX) for the application to determine if power supply voltages, load conditions, or package type need to be modified for the EL5292 to remain in the safe operating area. These parameters are calculated in Equation 1: T JMAX = T MAX + ( θ JA × n × PD MAX ) (EQ. 1) where: TMAX = Maximum ambient temperature θJA = Thermal resistance of the package n = Number of amplifiers in the package PDMAX = Maximum power dissipation of each amplifier in the package PDMAX for each amplifier can be calculated in Equation 2: V OUTMAX PDMAX = ( 2 × V S × I SMAX ) + ( V S - V OUTMAX ) × ---------------------------R Current Limiting The EL5292 has no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. L (EQ. 2) where: VS = Supply voltage Power Dissipation With the high output drive capability of the EL5292, it is possible to exceed the +125°C Absolute Maximum junction temperature under certain very high load current conditions. Generally speaking when RL falls below about 25Ω, it is 14 ISMAX = Maximum supply current of 1A VOUTMAX = Maximum output voltage (required) RL = Load resistance FN7192.1 June 28, 2007 EL5292, EL5292A Small Outline Package Family (SO) A D h X 45° (N/2)+1 N A PIN #1 I.D. MARK E1 E c SEE DETAIL “X” 1 (N/2) B L1 0.010 M C A B e H C A2 GAUGE PLANE SEATING PLANE A1 0.004 C 0.010 M C A B L b 0.010 4° ±4° DETAIL X MDP0027 SMALL OUTLINE PACKAGE FAMILY (SO) INCHES SYMBOL SO-14 SO16 (0.300”) (SOL-16) SO20 (SOL-20) SO24 (SOL-24) SO28 (SOL-28) TOLERANCE NOTES A 0.068 0.068 0.068 0.104 0.104 0.104 0.104 MAX - A1 0.006 0.006 0.006 0.007 0.007 0.007 0.007 ±0.003 - A2 0.057 0.057 0.057 0.092 0.092 0.092 0.092 ±0.002 - b 0.017 0.017 0.017 0.017 0.017 0.017 0.017 ±0.003 - c 0.009 0.009 0.009 0.011 0.011 0.011 0.011 ±0.001 - D 0.193 0.341 0.390 0.406 0.504 0.606 0.704 ±0.004 1, 3 E 0.236 0.236 0.236 0.406 0.406 0.406 0.406 ±0.008 - E1 0.154 0.154 0.154 0.295 0.295 0.295 0.295 ±0.004 2, 3 e 0.050 0.050 0.050 0.050 0.050 0.050 0.050 Basic - L 0.025 0.025 0.025 0.030 0.030 0.030 0.030 ±0.009 - L1 0.041 0.041 0.041 0.056 0.056 0.056 0.056 Basic - h 0.013 0.013 0.013 0.020 0.020 0.020 0.020 Reference - 16 20 24 28 Reference - N SO-8 SO16 (0.150”) 8 14 16 Rev. M 2/07 NOTES: 1. Plastic or metal protrusions of 0.006” maximum per side are not included. 2. Plastic interlead protrusions of 0.010” maximum per side are not included. 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994 15 FN7192.1 June 28, 2007 EL5292, EL5292A Mini SO Package Family (MSOP) 0.25 M C A B D MINI SO PACKAGE FAMILY (N/2)+1 N E MDP0043 A E1 MILLIMETERS PIN #1 I.D. 1 B (N/2) e H C SEATING PLANE 0.10 C N LEADS SYMBOL MSOP8 MSOP10 TOLERANCE NOTES A 1.10 1.10 Max. - A1 0.10 0.10 ±0.05 - A2 0.86 0.86 ±0.09 - b 0.33 0.23 +0.07/-0.08 - c 0.18 0.18 ±0.05 - D 3.00 3.00 ±0.10 1, 3 E 4.90 4.90 ±0.15 - E1 3.00 3.00 ±0.10 2, 3 e 0.65 0.50 Basic - L 0.55 0.55 ±0.15 - L1 0.95 0.95 Basic - N 8 10 Reference - 0.08 M C A B b Rev. D 2/07 NOTES: 1. Plastic or metal protrusions of 0.15mm maximum per side are not included. L1 2. Plastic interlead protrusions of 0.25mm maximum per side are not included. A 3. Dimensions “D” and “E1” are measured at Datum Plane “H”. 4. Dimensioning and tolerancing per ASME Y14.5M-1994. c SEE DETAIL "X" A2 GAUGE PLANE L A1 0.25 3° ±3° DETAIL X All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 16 FN7192.1 June 28, 2007