AOB0000CE7

Discontinued
Metal (Oxide) Film
Fusing Resistors, ERQH, C
Metal (Oxide) Film Fusing Resistors
Type: ERQH
(Flame retardative hermetic type)
Type:
ERQC
(Flameproof bath-tub type, Axial leads)
n Features
l Accurate Fusing Characteristic
Accurate fusing characteristic can be applied to safety circuit in wide range of electronic equipment
l Flameproof
Safety flameproof construction in a ceramic tube or case
l Hot Spot Temperature
The temperature of resistor surface shall not exceed 600 ûC (1112 ûF)
l Uniform Quality Reliable
An exclusive automated process-developed, built, and used only by Matsushita and severe quality control
system results in uniform quality and consistent performance in reliability
l High Dielectric Withstanding Voltage
Resistor may withstand a high potential up to 1000 V
n Construction
Flame-retardant, hermetically sealed
Metal (oxide) film
ERQ-12H type
Spiraling turns
Lead wire
Marking
Ceramic tube
Ceramic core
Fusing glass
End cap
Flame-proof epoxy resin
Sealing washer
Design and specifications are each subject to change without notice.
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER110 –
Discontinued
Metal (Oxide) Film
Fusing Resistors, ERQH, C
n Explanation of Part Numbers
1
2
3
E
R
Q
Product Code
Metal (Oxide) Film
Fusing Resistors
Power Rating
at 70¡C amb.
12 0.5 W
1
1W
2
2W
3
3W
4
5
6
7
2
C
J
Special Feature
H Hermetic
(0.5 W)
Bath-tub
C Axial leads
8
Resistance
Tolerance
J ± 5%
K ±10 %
9
10
11
1
0
1
Resistance Value
The first two digits are
significant figures of
resistance and the third
one denotes number of
zeros following.
Decimal point is
expressed by R as 1.5=
1R5.
12
Suffix for Packaging and/or
Cut & Formed Leads
Nil Std.bulk packing
V Axial taped & box
P P type cut & formed
type cut &
PáááS PáááS
formed
The above example shows a standard bath-tub type Metal (Oxide) Film Fusing Resistors, 2 W power rating, resistance value of 100 W, tolerance of
5 %, and package of standard bulk packing.
n Ratings
Type
Power
Rating
at 70 ¡C
(W)
ERQ12H
0.5
ERQ1C
1
ERQ2C
2
ERQ3C
3
Maximum
Overload
Voltage
3 times of RCWV(1)
Dielectric
Resistance
WithTolerance
standing
(%)
Voltage(V)
AC 1000
AC 1000
2.5 times of
RCWV
AC 1000
AC 1000
K (±10)
J (± 5)
K (±10)
J (± 5)
K (±10)
J (± 5)
K (±10)
J (± 5)
Resistance
Range (W)
min.
max.
0.22
1
0.33
1
0.33
1
0.33
1
0.82
3.9 k
0.82
1k
0.82
1k
0.82
3.3 k
Standard Marking T.C.R. Mass
Resistance Method [´10-6/ûC (Weight)
Values
on Body (ppm/ûC)] [g/pc.]
E12
E24
E12
E24
E12
E24
E12
E24
0.73
Stamp
±500
1.1
2
5.1
(1) Rated Continuous Working Voltage (RCWV) shall be determined from RCWV=Ã Power Rating ´ Resistance Value
Power Derating Curve
For resistors operated in ambient temperatures above
70 ûC, power rating shall be derated in accordance
with the right figure.
Design and specifications are each subject to change without notice.
Rated Load (%)
Maximum Open Circuit Voltage
Refering to the maximum value of the voltage applied between terminals of the resistor when the resistor is
opened in an electric circuit, it is defined by type and resistance.
Please stay within the specified voltage. (Please refer to ER115 page)
120
Ð30 ¡C
70 ¡C
100
80
60
C type
40
H type
20
150 ¡C
0 Ð40 Ð20 0 20 40 60 80 100 120 140 160 180 200 220
Ð60
Ambient Temperature (¡C)
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER111 –
Discontinued
Metal (Oxide) Film
Fusing Resistors, ERQH, C
n Explanation of marking
Type C
Black stamp
Symbol
Rated power
WJ
16
712
Manufacturing number
Rated power, resistance value and Tolerance
1 0 8
1/2W
3.3
J
Symbol
Date code (Year,Month,Week)
Code for fuse resistors
n Dimensions in mm (not to scale)
k
Date code (Year,Month,Week)
Type ERQ12H
Dimensions (mm)
Type
W
Q712
Tolerance
Resistance value
Red stamp
+3
13 Ð2 (mm)
fd
fD
L
fD
A
ERQ12H
12.0±1.5
5.3±1.0
28.5±3.0 0.65±0.05
Ñ
ERQ1C
13.0±1.0
Ñ
25.0±4.0 0.65±0.05
5.5±1.0
ERQ2C
18.0±1.0
Ñ
25.0±4.0 0.80±0.05
6.4±1.0
ERQ3C
22.0±1.0
Ñ
32.0±4.0 0.80±0.05
9.5±1.0
fd
l
l
L
Type ERQC
fd
L
l
A
Type 12H
A
l
n Cut & Formed Type
Type ÒPÓ
S
h2
h1
fD
L
f0.65±0.05
0.8
3 max.
±
1.2 0.2
Unit: mm
Part No.
L
fD
S
h1
h2
ERQ12H1111P
12.0±1.5
f5.3±1.0
17.5±1.5
5.85±1.50
4.0±1.0
Type ÒPáááSÓ
S
A
A
h2
h1
L
fd
W2
3 max.
W1
Unit: mm
Part No.
L
S
fd
A
ERQ1C1P111S (1 W)
13.0
20.0
0.65
5.5
ERQ2C1P111S (2 W)
18.0±1.0
25.0±2.0
0.80±0.10
6.4±1.0
±1.0
±2.0
Design and specifications are each subject to change without notice.
±0.10
±1.0
h1
6.0
±1.5
5.8±1.5
h2
4.0
±1.0
4.0±1.0
W1
1.2
±0.2
1.4±0.2
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER112 –
W2
0.8
1
Metal (Oxide) Film
Fusing Resistors, ERQH, C
Discontinued
n Axial Taping Specifications
+3
l2
13 Ð2
+3
13 Ð2
Standard quantity
(per box) 1000 pcs.
D
l1
95±2
l1
D/2
52.0±1.0
10.0±0.5
Type ERQ12H
75
6.0±1.0
|
l1-l2 | < 2.0
+2
Ð1
±3
325
All dimensions are in millimeters
n Pakaging Methods
Contact factory pakaging methods. (Type ERQC)
n Performance Specifications
Characteristics
Specifications
Test Methods
Flame-Retardancy
Not have any specimens which
burn with flaming combustion time
for more than 10 seconds after
each application of the test flame.
The test flame is placed to remain for 15 seconds
and removed for 15 seconds.
The test shall be repeated until resistor has been
subjected to 5 applications of the test flame.
When resistors are tested using the
specified circuit, the resistors shall
Fusing Characteristics meet the requirements specified respectively.
(Refer to ER114 page)
Tested on individual specified circuit, using stable
power supply.
Maximum open
circuit voltage
When resistors are tested using the
specified circuit, the resistors shall
meet the requirements specified respectively.
(Refer to ER115 page)
Design and specifications are each subject to change without notice.
Tested on individual specified circuit.
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER113 –
Metal (Oxide) Film
Fusing Resistors, ERQH, C
Discontinued
n Fusing characteristics for ERQH, C type
(unit : sec)
Multiple of the power rating (times)
ERQ12H type
10
12
16
20
0.22 to 0.82 (W)
Resistance value
1.0 to
4.3 (W)
4.7 to
16 (W)
18 to
47 (W)
51 to
200 (W)
220 to
620 (W)
< 150
680 to 3.9 k (W)
25
30
40
< 30
< 25
< 10
< 45
< 25
< 20
< 10
< 180
< 90
< 45
< 25
< 20
< 10
< 120
< 60
< 45
< 15
< 10
< 7
< 45
< 25
< 10
< 45
< 30
< 20
< 10
< 45
< 25
< 180
< 90
(unit : sec)
Multiple of the power rating (times)
ERQ1C type
10
0.33 to 0.91 (W)
Resistance value
12
16
20
25
30
< 300
< 90
< 180
< 40
< 20
< 10
< 45
< 15
< 7
< 7
1.0 to
3.9 (W)
4.3 to
16 (W)
< 90
< 60
< 30
< 10
< 7
< 7
18 to
47 (W)
< 60
< 30
< 15
< 10
< 7
< 7
51 to
180 (W)
< 90
< 20
< 15
< 10
200 to
620 (W)
< 60
< 20
< 7
< 7
680 to
1 k (W)
< 60
< 10
< 7
< 7
< 90
(unit : sec)
Multiple of the power rating (times)
ERQ2C type
10
12
0.33 to 0.91 (W)
Resistance value
16
20
25
30
< 90
< 30
< 15
< 7
1.0 to
3.9 (W)
< 90
< 45
< 20
< 15
< 7
4.3 to
30 (W)
< 45
< 30
< 10
< 7
< 7
33 to
47 (W)
< 30
< 20
< 10
< 7
< 7
51 to
180 (W)
< 45
< 120
< 60
< 20
< 10
< 7
200 to
620 (W)
< 90
< 30
< 10
< 7
< 7
680 to
1 k (W)
< 30
< 20
< 10
< 7
< 7
< 60
(unit : sec)
Multiple of the power rating (times)
ERQ3C type
10
12
0.33 to 0.91 (W)
1.0 to
Resistance value
3.9 (W)
16
20
25
30
< 240
< 90
< 45
< 20
< 240
< 90
< 20
< 15
4.3 to
20 (W)
< 300
< 120
< 60
< 20
< 15
< 15
22 to
91 (W)
< 100
< 60
< 30
< 15
< 15
< 15
100 to
200 (W)
< 180
< 90
< 30
< 20
< 15
220 to 3.3 k (W)
< 90
< 60
< 20
< 15
< 15
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER114 –
Discontinued
Metal (Oxide) Film
Fusing Resistors, ERQH, C
n Maximum open circuit voltage for ERQH, C type
Maximum open circuit voltage
Referting to the maximum value of the voltage applied between terminals of the resistor when the resistor is
opened in an electric circuit, it is defined by type and resistance. Please stay within the specified voltage.
Shall be confirmed carefully in actual circuit before use.
ERQH, C type
Testing circuit
ERQ12H type
ERQ1C type
1000
Maximum open circuit voltage (V)
Maximum open circuit voltage (V)
1000
100
100
10
10
0.1
1
10
100
1000
0.1
10000
1
100
1000
10000
1000
10000
ERQ3C type
ERQ2C type
1000
Maximum open circuit voltage (V)
1000
Maximum open circuit voltage (V)
10
Resistance value (Ω)
Resistance value (Ω)
100
100
10
10
0.1
1
10
100
1000
10000
Design and specifications are each subject to change without notice.
0.1
1
10
100
Resistance value (Ω)
Resistance value (Ω)
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER115 –
Metal (Oxide) Film
Fusing Resistors, ERQH, C
Discontinued
Cautions for Safety
The following are precautions for individual products. Please also refer to the precautions common to Fixed Resistors shown on page ER3 of this catalog.
1. Checking the fusing conditions
1) Fusing characteristics differ depending on the type, shape, and resistance. Check the fusing conditions
before selecting the type of Metal (Oxide) Film Fusing Resistors (hereafter called the Fusing Resistors) to be
used.
2) Use the Fusing Resistors under the maximum open circuit voltage. Otherwise, arcing may occur when a voltage
much higher than the rated one is applied in the event of an abnormality in the circuit, or when a high voltage
is applied after fusing.
2. Checking for pulse voltage, impact voltage, and transient voltage
Make sure to evaluate and check the Fusing Resistors mounted on your product if they are to be mounted on
a circuit that generates an impact voltage, or if there is a possibility that the transient phenomenon
(significantly high voltage applied in a short time) may occur or that a pulse voltage with a high peak voltage
may be applied. Make sure to consult our sales staff before using the Fusing Resistors under special conditions.
3. Conditions of use in a steady state
Make sure that the load conditions have a sufficient allowance for the power derating curve. The characteristics
of the Fusing Resistors are set by using a constant voltage circuit.
(Data for Reference)
n Pulse Characteristics (Usual)
Pp (Vp)
PP
VP
t
T
VR
P
R
Vp max.
t
T
Withstand pulse limit power is calculated by the next
method.
PP = K á P á T/t
VP = Ã K á P á R á T/t
Reference to the right about a fixed number of
VP max.
:
:
:
:
:
:
:
:
Pulse limit power (W)
Pulse limit voltage (V)
Pulse continuous time (s)
Period (s)
Rated voltage (V)
Rated power (W)
Resistance value (W)
Max. pulse limit voltage (V)
Type
K
Vp max. (V)
ERQ12H
0.60
200
ERQ1C
0.30
200
ERQ2C
0.25
300
ERQ3C
0.20
300
l T>1(s) ® T=1(s)
l T/t>100 ® T/t=100
l PP<P ® P stands for PP
(VP<VR ® VR stands for VP)
l Added voltage<Vp max.
l PP or VP is reference value
Conditions : Pulse added time=1000 h
Resistance change=±5 %
Room temperature
Design and specifications are each subject to change without notice.
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER116 –
Metal (Oxide) Film
Fusing Resistors, ERQH, C
Discontinued
n Fusing Characteristics (Constant Voltage Circuit)
(Fusing specification is refer to ER114 page)
ERQ12H
ERQ1C
1
100
100
1 k
70
60
50
40
W
W
W
100
1 k
70
60
50
40
30
20
10
7
6
5
4
20
10
7
6
5
4
3
3
2
2
1
1
0
8
10
12
15
20
25
30
0
8
Multiple of the rated power
10
12
15
20
25
30
Multiple of the rated power
ERQ2C
ERQ3C
W
W
1 k W
1
1
100
3.3 k
100
70
60
50
40
200
W
W
100
50
20
10
Fusing time (s)
Fusing time (s)
30
7
6
5
4
3
10
7
6
5
4
2
3
1
0
8
10
12
15
20
25
2
30
Multiple of the rated power
1
0
8
10
12
15
20
25
Multiple of the rated power
n Hot Spot Temperature (for Reference)
400
2CJ680
Temperature rise
o
T (K)
500
Measuring point
300
3CJ1R0
200
1CJ680
100
12HJ680
0
W
W
W
30
Fusing time (s)
Fusing time (s)
1
100
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Multiple of the rated power
Design and specifications are each subject to change without notice.
Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
– ER118 –
30
Caution for Safety
(Common precautions for Fixed Resistors)
¥ When using our products, no matter what sort of equipment they might be used for, be sure to make a written
agreement on the specifications with us in advance. The design and specifications in this catalog are subject
to change without prior notice.
¥ Do not use the products beyond the specifications described in this catalog.
¥ This catalog explains the quality and performance of the products as individual components. Before use, check
and evaluate their operations when installed in your products.
¥ Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment
where a defect in these products may cause the loss of human life or other significant damage, such as damage to
vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating
appliances, combustion/gas equipment, rotating equipment, and disaster/crime prevention equipment.
] Systems equipped with a protection circuit and a protection device
] Systems equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault
(1) Precautions for use
¥ These products are designed and manufactured for general purpose and standard use in general electronic
equip ment (e.g. AV equipment, home electric appliances, office equipment, information and communication
equipment)
¥ These products are not intended for use in the following special conditions. Before using the products,
carefully check the effects on their quality and performance, and determine whether or not they can be used.
1. In liquid, such as water, oil, chemicals, or organic solvent
2. In direct sunlight, outdoors, or in dust
3. In salty air or air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
4. In an environment where strong static electricity or electromagnetic waves exist
5. In an environment where these products cause dew condensation
6. Sealing or coating of these products or a printed circuit board on which these products are mounted, with
resin or other materials
¥ These products generate Joule heat when energized. Carefully position these products so that their heat will
not affect the other components.
¥ Carefully position these products so that their temperatures will not exceed the category temperature range due
to the effects of neighboring heat-generating components. Do not mount or place heat-generating components
or inflammables, such as vinyl-coated wires, near these products .
¥ Note that non-cleaning solder, halogen-based highly active flux, or water-soluble flux may deteriorate the
perfor mance or reliability of the products.
¥ Carefully select a flux cleaning agent for use after soldering. An unsuitable agent may deteriorate the performance
or reliability. In particular, when using water or a water-soluble cleaning agent, be careful not to leave water
residues. Otherwise, the insulation performance may be deteriorated.
(2) Precautions for storage
The performance of these products, including the solderability, is guaranteed for a year from the date of arrival
at your company, provided that they remain packed as they were when delivered and stored at a temperature
of 5 ¡C to 35 ¡C and a relative humidity of 45 % to 85 %.
Even within the above guarantee periods, do not store these products in the following conditions. Otherwise,
their electrical performance and/or solderability may be deteriorated, and the packaging materials (e.g. taping
materials) may be deformed or deteriorated, resulting in mounting failures.
1. In salty air or in air with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NO2
2. In direct sunlight
<Package markings>
Package markings include the product number, quantity, and country of origin.
In principle, the country of origin should be indicated in English.
– ER3 –