EVB-USB3613
Evaluation Board
User’s Guide
2013 Microchip Technology Inc.
DS50002194A
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash
and UNI/O are registered trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MTP, SEEVAL and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Silicon Storage Technology is a registered trademark of
Microchip Technology Inc. in other countries.
Analog-for-the-Digital Age, Application Maestro, BodyCom,
chipKIT, chipKIT logo, CodeGuard, dsPICDEM,
dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O,
Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA
and Z-Scale are trademarks of Microchip Technology
Incorporated in the U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
GestIC and ULPP are registered trademarks of Microchip
Technology Germany II GmbH & Co. & KG, a subsidiary of
Microchip Technology Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2013, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
ISBN: 978-1-62077-457-1
QUALITY MANAGEMENT SYSTEM
CERTIFIED BY DNV
== ISO/TS 16949 ==
DS50002194A-page 2
Microchip received ISO/TS-16949:2009 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
2013 Microchip Technology Inc.
EVB-USB3613 Evaluation Board User’s Guide
Object of Declaration: EVB-USB3613 Evaluation Board
2013 Microchip Technology Inc.
DS50002194A-page 3
EVB-USB3613 Evaluation Board User’s Guide
NOTES:
2013 Microchip Technology Inc.
DS50002194A-page 4
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Table of Contents
Preface ........................................................................................................................... 7
Introduction............................................................................................................ 7
Document Layout .................................................................................................. 7
Conventions Used in this Guide ............................................................................ 8
The Microchip Web Site ........................................................................................ 9
Development Systems Customer Change Notification Service ............................ 9
Customer Support ................................................................................................. 9
Document Revision History ................................................................................. 10
Chapter 1. Overview
1.1 Introduction ................................................................................................... 11
1.2 Features ....................................................................................................... 11
1.3 General Description ...................................................................................... 12
Chapter 2. Hardware Configuration
2.1 Hardware Description ................................................................................... 13
2.1.1 Port Assignment ........................................................................................ 13
2.1.2 USB3613 Configuration ............................................................................. 15
2.1.3 Clock Source – 12 MHz Oscillator ............................................................. 15
2.1.4 Power Source – Self-Powered .................................................................. 15
2.1.5 Powered State LED ................................................................................... 15
2.1.6 RESETn LED ............................................................................................ 16
2.1.7 Port Power LEDs ....................................................................................... 16
2.1.8 Hub Connect LED ..................................................................................... 16
2.1.9 Connector Description ............................................................................... 16
Chapter 3. Battery Charging Support
3.1 Battery Charging Modes ............................................................................... 19
3.2 Charging Port Roles ..................................................................................... 19
3.2.1 BC1.2 Charging Downstream Port (CDP) Description .............................. 20
3.2.2 Standard Downstream Port (SDP) Description ......................................... 20
3.2.3 Dedicated Charger Emulation Port (DCP) Description .............................. 20
Appendix A. EVB-USB3613 Evaluation Board
A.1 Introduction .................................................................................................. 23
Appendix B. EVB-USB3613 Evaluation Board Schematic
B.1 Introduction .................................................................................................. 25
Appendix C. Bill of Materials (BOM)
C.1 Introduction .................................................................................................. 27
Worldwide Sales and Service .................................................................................... 31
2013 Microchip Technology Inc.
DS50002194A-page 5
EVB-USB3613 Evaluation Board User’s Guide
NOTES:
DS50002194A-page 6
2013 Microchip Technology Inc.
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Preface
NOTICE TO CUSTOMERS
All documentation becomes dated, and this manual is no exception. Microchip tools and
documentation are constantly evolving to meet customer needs, so some actual dialogs
and/or tool descriptions may differ from those in this document. Please refer to our web site
(www.microchip.com) to obtain the latest documentation available.
Documents are identified with a “DS” number. This number is located on the bottom of each
page, in front of the page number. The numbering convention for the DS number is
“DSXXXXXA”, where “XXXXX” is the document number and “A” is the revision level of the
document.
For the most up-to-date information on development tools, see the MPLAB® IDE online help.
Select the Help menu, and then Topics to open a list of available online help files.
INTRODUCTION
This chapter contains general information that will be useful to know before using the
EVB-USB3613 Evaluation Board. Items discussed in this chapter include:
•
•
•
•
•
•
Document Layout
Conventions Used in this Guide
The Microchip Web Site
Development Systems Customer Change Notification Service
Customer Support
Document Revision History
DOCUMENT LAYOUT
This document describes how to use the EVB-USB3613 Evaluation Board as a
demonstration platform optimized for portable applications. The manual layout is as
follows:
• Chapter 1. “Overview” – Shows a brief description of the EVB-USB3613
Evaluation Board.
• Chapter 2. “Hardware Configuration” – Includes information about the
hardware configuration of the EVB-USB3613 Evaluation Board.
• Chapter 3. “Battery Charging Support” – Provides information about the
EVB-USB3613 Evaluation Board battery charging features.
• Appendix A. “EVB-USB3613 Evaluation Board” – This appendix shows the
EVB-USB3613 Evaluation Board.
• Appendix B. “EVB-USB3613 Evaluation Board Schematic” – This appendix
shows the EVB-USB3613 Evaluation Board schematic.
• Appendix C. “Bill of Materials (BOM)” – This appendix includes the
EVB-USB3613 Evaluation Board Bill of Materials (BOM).
2013 Microchip Technology Inc.
DS50002194A-page 7
EVB-USB3613 Evaluation Board User’s Guide
CONVENTIONS USED IN THIS GUIDE
This manual uses the following documentation conventions:
DOCUMENTATION CONVENTIONS
Description
Arial font:
Italic characters
Represents
Referenced books
Emphasized text
A window
A dialog
A menu selection
A field name in a window or
dialog
A menu path
MPLAB® IDE User’s Guide
...is the only compiler...
the Output window
the Settings dialog
select Enable Programmer
“Save project before build”
A dialog button
A tab
A number in verilog format,
where N is the total number of
digits, R is the radix and n is a
digit.
A key on the keyboard
Click OK
Click the Power tab
4‘b0010, 2‘hF1
Italic Courier New
Sample source code
Filenames
File paths
Keywords
Command-line options
Bit values
Constants
A variable argument
Square brackets [ ]
Optional arguments
Curly brackets and pipe
character: { | }
Ellipses...
Choice of mutually exclusive
arguments; an OR selection
Replaces repeated text
#define START
autoexec.bat
c:\mcc18\h
_asm, _endasm, static
-Opa+, -Opa0, 1
0xFF, ‘A’
file.o, where file can be
any valid filename
mcc18 [options] file
[options]
errorlevel {0|1}
Initial caps
Quotes
Underlined, italic text with
right angle bracket
Bold characters
N‘Rnnnn
Text in angle brackets < >
Courier New font:
Plain Courier New
Represents code supplied by
user
DS50002194A-page 8
Examples
File>Save
Press <Enter>, <F1>
var_name [,
var_name...]
void main (void)
{ ...
}
2013 Microchip Technology Inc.
Preface
THE MICROCHIP WEB SITE
Microchip provides online support via our web site at www.microchip.com. This web
site is used as a means to make files and information easily available to customers.
Accessible by using your favorite Internet browser, the web site contains the following
information:
• Product Support – Data sheets and errata, application notes and sample
programs, design resources, user’s guides and hardware support documents,
latest software releases and archived software
• General Technical Support – Frequently Asked Questions (FAQs), technical
support requests, online discussion groups, Microchip consultant program
member listing
• Business of Microchip – Product selector and ordering guides, latest Microchip
press releases, listing of seminars and events, listings of Microchip sales offices,
distributors and factory representatives
DEVELOPMENT SYSTEMS CUSTOMER CHANGE NOTIFICATION SERVICE
Microchip’s customer notification service helps keep customers current on Microchip
products. Subscribers will receive e-mail notification whenever there are changes,
updates, revisions or errata related to a specified product family or development tool of
interest.
To register, access the Microchip web site at www.microchip.com, click on Customer
Change Notification and follow the registration instructions.
The Development Systems product group categories are:
• Compilers – The latest information on Microchip C compilers, assemblers, linkers
and other language tools. These include all MPLAB C compilers; all MPLAB
assemblers (including MPASM assembler); all MPLAB linkers (including MPLINK
object linker); and all MPLAB librarians (including MPLIB object librarian).
• Emulators – The latest information on Microchip in-circuit emulators.This
includes the MPLAB REAL ICE and MPLAB ICE 2000 in-circuit emulators.
• In-Circuit Debuggers – The latest information on the Microchip in-circuit
debuggers. This includes MPLAB ICD 3 in-circuit debuggers and PICkit 3 debug
express.
• MPLAB IDE – The latest information on Microchip MPLAB IDE, the Windows
Integrated Development Environment for development systems tools. This list is
focused on the MPLAB IDE, MPLAB IDE Project Manager, MPLAB Editor and
MPLAB SIM simulator, as well as general editing and debugging features.
• Programmers – The latest information on Microchip programmers. These include
production programmers such as MPLAB REAL ICE in-circuit emulator, MPLAB
ICD 3 in-circuit debugger and MPLAB PM3 device programmers. Also included
are nonproduction development programmers such as PICSTART Plus and PICkit
2 and 3.
CUSTOMER SUPPORT
Users of Microchip products can receive assistance through several channels:
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
2013 Microchip Technology Inc.
DS50002194A-page 9
EVB-USB3613 Evaluation Board User’s Guide
Customers should contact their distributor, representative or field application engineer
(FAE) for support. Local sales offices are also available to help customers. A listing of
sales offices and locations is included in the back of this document.
Technical support is available through the web site at:
http://www.microchip.com/support
DOCUMENT REVISION HISTORY
Revision A (September 2013)
• Initial Release of this Document.
DS50002194A-page 10
2013 Microchip Technology Inc.
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Chapter 1. Overview
1.1
INTRODUCTION
The USB3613 is a low-power, full-featured and OEM configurable Multi-Transaction
Translator (MTT) USB 2.0 hub controller with three downstream ports optimized for
portable applications. The USB3613 is fully compliant with the USB 2.0 Specification,
USB 2.0 Link Power Management (LPM) Addendum, High-Speed Inter-Chip (HSIC)
USB Electrical Specification Revision 1.0 and attaches to an upstream port as a
high-speed hub. The 3-port hub supports low-speed, full-speed and high-speed
downstream devices on all of the enabled (non-HSIC) downstream ports. HSIC ports
support only high-speed operation. The USB3613 supports both upstream and
downstream battery charging (BC1.2) detection. The EVB-USB3613BC Evaluation
Board demonstrates a stand-alone application for the USB3613 device with advanced
power saving options and configurable port assignments. See Section 1.2 “Features”
for more information.
1.2
FEATURES
• USB3613 in a 30-pin WLCSP RoHS compliant package
• Two USB 2.0 downstream ports with ganged port power and overcurrent sense
(OCS)
• One downstream HSIC port (downstream port 3)
• High-Speed (480 Mbps), Full-Speed (12 Mbps) and Low-Speed (1.5 Mbps)
compatible
• USB Battery Charging is supported on all downstream USB ports up to 2A (BC1.2
CDP, SDP and DCP)
• Multi-Transaction Translator is enabled
• Supports internal default hub configuration. Optionally supports configuration from
external SPI or EEPROM
• SMBus interface header available
• Low-Cost, 4-Layer space saving design with two outer signal layers, a power
inner layer and a ground inner layer
• Self-Powered operation
• Operates from one single voltage (+5.0 VDC, 4 Amp regulated) external DC
power supply
• On Board MCP1725 +3.3 VDC. 0.5 Amp regulator
• +5V, Reset, Hub Connect and port power LED indicators
• ESD/EMI component footprints provided (optional)
• Single 12 MHz crystal clock source
• External GPIO pin headers
• Schematics, layout and bill of materials are available to minimize new product
development time
2013 Microchip Technology Inc.
DS50002194A-page 11
EVB-USB3613 Evaluation Board User’s Guide
1.3
GENERAL DESCRIPTION
The EVB-USB3613BC is an evaluation and demonstration platform featuring the
USB3613 Ultra Fast USB 2.0 Hub on a 4-layer RoHS compliant Printed Circuit Board
(PCB).
The EVB-USB3613 is designed to demonstrate the unique features of this device using
a low-cost PCB implementation with ganged port power control for the two downstream
USB 2.0 ports. Both downstream USB 2.0 ports include a high current port power
controller to fully support USB battery charging as a high current walk-up port.
Note:
Do not exceed 4A total current consumption from 5 VDC.
The EVB-USB3613 is designed to support internal default configuration settings and
an external I2C™ EEPROM (optional) for custom configured functionality. A location is
provided for an external I2C EEPROM device for configuration at U8. Alternatively, a
firmware can be downloaded onto a dual-output SPI Flash device located at U17.
Figure 2-2 shows the top and bottom level silk screen and copper layers. A block
diagram of the EVB-USB3613 is shown in Figure 2-3.
DS50002194A-page 12
2013 Microchip Technology Inc.
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Chapter 2. Hardware Configuration
2.1
HARDWARE DESCRIPTION
The EVB-USB3613 has one on board regulator. The MCP1725 (U6) generates +3.3
VDC for the hub device circuitry and performs voltage supervisor and RESETn
functions. The USB3613 generates its own +1.2 VDC for internal use with on-chip +1.2
VDC regulators. The internal +1.2 VDC regulator tied to the oscillator and
Phase-Locked Loop (PLL) is turned off during suspend to minimize suspend current.
Downstream port power is distributed by two independent power switches at up to 2A
per port via U1 and U2.
Note:
Do not exceed 4A total current consumption from +5 VDC.
Downstream port 1 and port 2 have USB 2.0 connectors with USB 2.0 compliant
decoupling and separate shield grounds. Downstream port 3 has U.FL connectors (J20
and J21) to support Data and Strobe HSIC signals.
2.1.1
Port Assignment
The downstream ports are numbered 1 through 3. Downstream port 1 and port 2 are
the USB 2.0 ports. Downstream port 3 is an HSIC port. The USB3613 allows
downstream port 1 and/or port 2 to be configured for high current battery USB charging.
Power to downstream port 1 and port 2 is controlled through the AP2111 devices U1
and U2. Each device provides up to 2A to the corresponding downstream port. Both of
these port power controllers are enabled via a shared PRTPWR pin on the USB3613.
Overcurrent sensing of both port power controllers is also monitored on the same
PRTPWR pin.
Note:
There is only a maximum of 4A provided across the entire evaluation board.
The EVB-USB3613 must be connected to an HSIC upstream host via the Data0 (J14)
and Strobe0 (J15) connectors using the provided U.FL coaxial cables. When removing
these cables from the evaluation board for any reason, the provided HSIC Extraction
tool must be used. Figure 2-1shows the recommended usage of the HSIC extraction
tool per the Hirose U.FL data sheet on proper use of the plugs.
2013 Microchip Technology Inc.
DS50002194A-page 13
EVB-USB3613 Evaluation Board User’s Guide
FIGURE 2-1:
U.FL COAXIAL CABLE EXTRACTION GUIDELINES
Usage Precautions
1. Plugs
(1) Mating/Unmating
1) To disconnect the connectors, insert the end portion of U.FL-LP-N-2 under the
connector flanges and pull off vertically, in the direction of the connector mating axis.
2) To mate the connectors, the mating axes of both connectors must be aligned. The
“click” confirms a fully-mated connection. Do not attempt to insert on an extreme
angle.
(2) Pull forces on the cable after the connectors are mated. Do not apply a load to the
cable in excess of the values indicated in the diagram below.
(3) Precautions
Do NOT forcefully twist or deform wires.
An external HUB_CONN port control signal from the host must be wired to the
“HubConn” pin on the J23 header. This signal lets the USB3613 know when an HSIC
upstream host is ready to attach. Once a host has been attached and detected, the
green “HubConn” LED D18 lights up.
The EVB-USB3613 is designed to allow flexible configuration options. It can be
configured with default internal register settings through an SMBus or through a
downloadable external firmware to an SPI Flash. It supports “Quad-Page” configuration
OTP flash (four consecutive 200-byte configuration pages). The following sections
detail the various configuration methods and features.
DS50002194A-page 14
2013 Microchip Technology Inc.
Hardware Configuration
2.1.2
USB3613 Configuration
Default: Upon power-up, the USB3613 searches for an external SPI Flash device that
contains a valid signature. If an SPI device is not present, the firmware checks to see
whether SMBus is enabled. If the SMBus is disabled, the USB3613 attempts to load
the configuration from an external I2C EEPROM. If no external options are detected,
the USB3613 will operate using the internal default register settings. It also sets the
vendor ID, product ID, language ID, device ID and additional settings from internal
ROM code.
SPI Flash Option: If upon power-up an external SPI Flash device is present, the
external ROM is enabled and code execution is initiated from the external SPI device.
The SPI Flash device on the EVB-USB3613 is populated by default. To hold this device
in reset, the J33 “SPI Hold” two-pin header can be shorted together, thereby tying the
HOLD signal low.
SMBus Option: The SMBus interface is disabled by default via the 100 kOhm pull
down resistor on SMBCLK. To enable SMBus, the SMBCLK pin must be pulled high to
+3.3 VDC with a strong pull up resistor. This is often embedded within the external
SMBus tool (not included) when inserted onto the J13 SMBus header. All device
configuration must be performed via the Pro-Touch Programming Tool. For information
on this tool, contact your local sales representative. When SMBus is enabled, the
firmware configures the GPIOs to act as an SMBus slave. As an SMBus slave, the
firmware waits indefinitely for the SMBus configuration.
EEPROM Option: If the USB3613 does not detect an SMBus interface, it will check for
an I2C EEPROM (not populated by default). The EVB-USB3613 loads configuration
from an external two-wire I2C EEPROM when present. The EEPROM must be installed
either directly or through a DIP socket located at the U8 footprint and the “Manual I2C
Enable” headers J11 and J12 must be set to enable this option. By default, J11 and J12
are left open so that the I2C interface are only enabled by pull ups in the external
EEPROM device. When both J11 and J12 are jumpered, SDA and SCL on the I2C
interface are pulled high to +3.3 VDC externally. The EEPROM must be
pre-programmed before installation as the EVB-USB3613 is tied to an HSIC host. The
EVB-USB3613BC is compatible with I2C EEPROMs from several manufacturers. The
memory capacity must be at least 512 bytes.
2.1.3
Clock Source – 12 MHz Oscillator
By default, a 12 MHz oscillator OSC1 is populated on the evaluation board as the clock
source for the USB3613. An alternative clock source can be injected into the J54 SMA
“External Clock Input” connector if desired. The REFSEL[1:0] pins are both pulled high
to +3.3 VDC by default to configure the USB3613 to have an input reference clock
frequency of 12 MHz.
2.1.4
Power Source – Self-Powered
The EVB-USB3613 only supports self-powered operation and is powered by one +5
VDC regulated external DC power supply. The +5 VDC, 4A external DC power supply
plugs into the on board 2.1 mm connector J8. The external power supply controls the
on board +3.3 VDC MCP1725 voltage regulator. The evaluation board is setup so that
the +5 VDC feeds VBAT on the USB3613 which feeds the internal +3.3 VDC regulator.
The +3.3 VDC comes out on the VDD33 power pin which then feeds the internal +1.2
VDC regulator via the VDDCRREG pin. A +1.2 VDC is then output onto the VDDCR12
pin of the USB3613. Therefore, the USB3613 is powered completely by the +5 VDC
output of the external power supply.
2.1.5
Powered State LED
The LED D5 indicates when +5 VDC power is present.
2013 Microchip Technology Inc.
DS50002194A-page 15
EVB-USB3613 Evaluation Board User’s Guide
2.1.6
RESETn LED
The LED D6 indicates when the RESETn signal is driven low and the USB3613 is held
in the Reset state.
2.1.7
Port Power LEDs
LEDs D1 and D2 indicate when +5 VDC port power is available to the associated
downstream USB port(s).
2.1.8
Hub Connect LED
The LED D18 indicates when an upstream HSIC host is present.
2.1.9
Connector Description
The EVB-USB3613 has two USB connectors for downstream port 1 and port 2. The
upstream port as well as downstream port 3 have U.FL connectors for HSIC data and
strobe signals. Power is supplied via 2.1 mm power jack. See Table 2-1 for the list of
connectors. For more details, please see Appendix A. “EVB-USB3613 Evaluation
Board”.
TABLE 2-1:
CONNECTOR DESCRIPTION
Connector
Type
Description
J1
USB uAB
Downstream USB Port 1
J2
USB A
Downstream USB Port 2
J7
1x2 header
External Reset Control
J8
Power Jack 2.1 mm
+5 VDC Regulated Power Supply
J11, J12
1x2 headers
I2C™ External/Manual Enable
J13
2x5 header
SMBus I/F connection
J14
U.FL
Upstream HSIC Port 0 DATA
J15
U.FL
Upstream HSIC Port 0 STROBE
J18, J19
1x2 headers
Charge Detect [1:0]
J20
U.FL
Downstream HSIC Port 3 DATA
J21
U.FL
Downstream HSIC Port 3 STROBE
J22
1x2 header
Suspend/IRQ#/Interrupt
J33
1x2 header
SPI HOLD (to hold SPI in reset)
J54
SMA
External Clock Input
Component side top and bottom layers are shown in Figure 2-2 with silk screen
information to identify component locations.
DS50002194A-page 16
2013 Microchip Technology Inc.
Hardware Configuration
FIGURE 2-2:
2013 Microchip Technology Inc.
EVB-USB3613 TOP AND BOTTOM LEVEL SILK SCREEN AND
COPPER LAYERS
DS50002194A-page 17
EVB-USB3613 Evaluation Board User’s Guide
FIGURE 2-3:
5V
EVB-USB3613 BLOCK DIAGRAM
3V3 (To Board)
3.3V
Regulator
USB3613
(CSP30)
VDD33
1V2
From HSIC Host
Port 0
HSIC
U.FL
DATA
STROBE
HUB_CONN
DATA0
STROBE0
POWER
OCS
PRTPWR/
OCS
DATA3
STROBE3
10Kohm
Optional
SMBus
DS50002194A-page 18
POWER
OCS
GENERIC
PORT PWR
CTLR
(2A)
Port 1
USB 2.0
Conn
VBUS
D+
D-
Port 2
USB 2.0
Conn
SPI
3.3V
Optional
EEPROM
VBUS
D+
D-
D1+
D1-
D2+
D2-
Optional
SPI
GENERIC
PORT PWR
CTLR
(2A)
SDA
SCL
Data
Strobe
Port 3
HSIC
U.FL
10Kohm
SDA
SCL
SCL
SDA
2013 Microchip Technology Inc.
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Chapter 3. Battery Charging Support
3.1
BATTERY CHARGING MODES
The EVB-USB3613 supports several different Battery Charging modes, providing an
array of flexible configuration solutions. Both downstream port 1 and port 2 can be
separately configured for battery charging via OTP, downloadable external firmware to
an on board SPI Flash or through SMBus commands. Each port's configuration is
independent of the other ports.
The battery charging mechanism automatically switches ports between states that
perform the BC1.2 CDP handshake (which allows full USB communication with a USB
host while charging), and states that emulate the dedicated chargers from charging
device vendors. This allows support for the BC1.2 CDP mode and emulation of
dedicated chargers in DCP mode, without interfering with normal USB operation of any
USB 2.0 device attached to the port. Battery charging is supported through the use of
standard port power controllers.
Section 3.2 “Charging Port Roles” describes the modes of operation. For more
information on battery charging, please refer to the Application Note 34.5 and the USB
Battery Charging 1.2 specifications.
3.2
CHARGING PORT ROLES
The EVB-USB3613's battery charging enabled downstream ports automatically switch
between various roles depending on the USB state of the EVB-USB3613. These roles
are:
1.
2.
3.
4.
BC1.2 charging downstream port (CDP – 1.5A with data)
Standard downstream port (SDP – 0.5A with data)
Dedicated charger emulation port (DCP – power brick without data)
Custom profiles loaded via SMBus or OTP
When switching between roles, the EVB-USB3613 toggles power to the attached
device if appropriate. The power toggle occurs if charger or USB renegotiation is
necessary based on the following conditions:
1. If the port is in an SDP role while the hub is disconnected from the host, the port
toggles power when switching to a DCP role to allow the downstream device to
negotiate with the DCP mechanism.
2. If the port is in a DCP role and the port needs to switch to a CDP or an SDP role,
the port toggles power to allow the device to renegotiate with a CDP handshake
and/or USB attach.
When battery charging is disabled for a EVB-USB3613 port, the port acts as a normal
USB hub port.
When a USB port is in a state in which device-host USB communication is not possible,
a battery charging enabled port is not required to act as a USB hub port and is therefore
free to enter states that emulate dedicated chargers. For the EVB-USB3613, there are
two cases where this applies:
1. The EVB-USB3613 upstream port is not connected to a USB host (which on this
2013 Microchip Technology Inc.
DS50002194A-page 19
EVB-USB3613 Evaluation Board User’s Guide
evaluation board, it is tied to an HSIC host).
2. The EVB-USB3613 is in USB suspend with remote wake on the USB 2.0 portion
of the EVB-USB3613 disabled and no USB 2.0 device connected as a USB
device on the downstream port. If USB 2.0 remote wake is disabled, the hub
cannot generate resume signaling and does not need to detect a USB 2.0 attach.
In case 2, the EVB-USB3613's charging ports do not enter dedicated charging states
when there is a USB 2.0 device attached as a USB device. There are two reasons for
this behavior:
1. Entering dedicated charging states may involve changing the state of an
attached device due to power toggling and/or USB linestate changing. Because
the host system is unaware of the battery charging mechanism of the
EVB-USB3613, the host could find the device in an unexpected state when
exiting suspend.
2. The attached device will not be able to signal resume signaling to the host when
the port is in a dedicated charging state. Hubs must propagate resume signaling
from downstream devices even when remote wake generation is disabled for the
hub.
If the EVB-USB3613 is in USB 2.0 suspend with USB 2.0 remote wake disabled and a
USB-attached device is removed from a port, the port switches to the DCP role
because possible resume propagation is no longer required.
3.2.1
BC1.2 Charging Downstream Port (CDP) Description
Devices that do not follow the BC1.2 CDP specification behave as they normally would
when inserted into a standard USB port. The EVB-USB3613 ports in CDP mode allow
normal USB operation or communication between normal devices and USB hosts by
switching to the SDP role after downstream device detection and absence of a BC1.2
CDP handshake from the device. When a subsequent device detach is detected, the
port switches back to the CDP role.
Devices that follow the BC1.2 CDP specification are also allowed to communicate
normally with the USB host when inserted into the EVB-USB3613 ports in CDP mode.
Additionally, prior to allowing the normal USB connection between the host and the
BC1.2 device, the EVB-USB3613 port performs the BC1.2 CDP handshake to inform
the BC1.2-compliant device that it may draw current exceeding the USB specified
limits. When the handshake is complete, the port switches to the SDP role to allow USB
functionality for the device. When a subsequent device detach is detected, the port
switches back to the CDP role.
3.2.2
Standard Downstream Port (SDP) Description
When a port is in the SDP role, it behaves as a normal hub port and allow full USB
functionality for an attached downstream device.
3.2.3
Dedicated Charger Emulation Port (DCP) Description
The advantage of the EVB-USB3613 dedicated charger emulation port over the
BC1.2-specified DCP is that it supports BC1.2 compliant charging devices and many
non-BC1.2 compliant charging devices. The following paragraphs describe the
EVB-USB3613 modes of operation when its downstream ports are in dedicated
charging states (when normal USB connection is not required as described in previous
sections).
DS50002194A-page 20
2013 Microchip Technology Inc.
Battery Charging Support
Dynamic Mode:
The EVB-USB3613 can be configured to dynamically react to devices inserted into the
downstream ports and emulate the appropriate type of charger for the inserted device.
In this configuration, the port begins in Apple® charger emulation mode and switches
to China Charging, Blackberry® or BC1.2 device charger emulation when such devices
are detected by the port. When a device is detached, the port starts again in Apple
charger emulation mode.
Configurable 1A and 2A Apple modes are available depending on the capabilities of
each port's port power controller.
An EVB-USB3613 port with a standard port power controller also supports Samsung®
Galaxy Tab™ charger emulation in addition to the above modes.
Static Mode:
The EVB-USB3613 can be configured to keep the downstream ports in a fixed charger
emulation state. Currently, Apple and Samsung Galaxy Tab or China Charging fixed
charger emulation modes are available.
2013 Microchip Technology Inc.
DS50002194A-page 21
EVB-USB3613 Evaluation Board User’s Guide
NOTES:
DS50002194A-page 22
2013 Microchip Technology Inc.
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Appendix A. EVB-USB3613 Evaluation Board
A.1
INTRODUCTION
This appendix shows the EVB-USB3613 Evaluation Board.
FIGURE A-1:
EVB-USB3613 EVALUATION BOARD
2013 Microchip Technology Inc.
DS50002194A-page 23
EVB-USB3613 Evaluation Board
NOTES:
2013 Microchip Technology Inc.
DS50002194A-page 24
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Appendix B. EVB-USB3613 Evaluation Board Schematic
B.1
INTRODUCTION
This appendix shows the EVB-USB3613 Evaluation Board schematic.
2013 Microchip Technology Inc.
DS50002194A-page 25
External
Supply
5V, 4A
3V3
5V
U14
1
2.2K
74LVC1G14
open*: HUB_CONN = True
short: HUB_CONN = False
2, 1 = External HUB_CONN, Gnd
"Hub Conn"
D18
R57
4
Br_Grn-RA
TP9
BLACK
C25
+
5V
U0
U.FL
2
3
U.FL
Upstream
(Flex)
1
J14
A3
A2
DATA0
STRB0
1
J15
DM1/DATA1
DP1/STRB1
DATA0/DM0
STRB0/DP0
4
C21
OE
OUT
VCC
GND
R69
2
2
3
4
5
0.1uF
R41
R40
R42
3V3
33
A4
REFCLK
R70
33 DNP
Ext. Clock Input
J54
1
3V3
R32
R38
10K
10K
SMA
R17
10K
DNP
C1
E6
REFSEL0
REFSEL1
R19
10K
DNP
*Note:
System should supply RESET# in
an embedded hub implementation.
B2
RESET#
C3
RBIAS
U17
8
VCC
SCK
SI
SO
CS*
C63
0.1uF
4
WP*
HOLD*
GND
6
5
2
1
3
7
WP#
HOLD#
3V3
SHUNT1
SPI HOLD
J33
2
(*both open = Enable by ext. device PUs)
Man. I2C Enable ( both shorted = Man. Enable)
J12
1
2 R21
10K
SDA/SMBDATA
SCL/SMBCLK
1
2 R25
10K
J13
1
3
5
7
9
Aardvark_I/F
SMBus I/F
DATA3/DM3
STRB3/DP3
D1
C2
4
5
D5
C6
2
3
E5
D6
DDM3
SDP3
SPI
3V3
R33
I2C/SMBus
SDA/SMBDATA
SCL/SMBCLK
B4
VDD33
Power
VBAT
Port Power
3V3
Reg.
1
U.FL
STRB3
TP6
ORANGE
U8 24C04B-DIP8
1
VCC
A0 2
A1 3
7
WP
A2
A5
8
C34
0.1uF
4
SCL
SDA
TP15
YELLOW
6
5
TP7
BLACK
R30
100K
SKT1
EEPROM-DNP
4
5
10K
E3
ZERO
PCTL
C5
DLP11SN900SL2 L1
1
0.1uF
PWR1_3
3
2
BGX50A
BR2
3
C6
4
1
DLP11SN900SL2 L2
1
0.1uF
PWR2
3
2
BGX50A
BR3
3
VDDCRREG
1V2
Reg.
C7
0.1uF
SHLD2
U9
3V3 Regulator,
for Support Ckts,
~100 mA
1.2V Core
1.2V HSIC
VDDCR12 (1.0 uF)
5V
C42
U6 MCP1725-ADJ_SOIC8
1
8
VOUT
2 VIN1
VIN2
1.0uF
R26
10K
500mA
3
EN3
EXT_RST 6
DLP11SN900SL2 L3
PWR1_3
0.1uF
3V3
4
1
1
330
C2
TP3
WHITE
RESET#
to USB connector -->
DM3
DP3
R2
OCS#
TP5
BLACK
B3
C4
C33
to USB connector -->
DM2
DP2
D2
Br_Grn-RA
"PPWR2"
PPWRA
2
4
BGX50A
BR1
3
4
1
2
4
3
2
D2
Port
2
SUSP/IRQ#/INT#
J22
1
C37
DNP
1.0uF
to USB connector -->
R6
2.2K
8
1
USB-A Jack
5
SR1 6
SL1 7
SR2 8
SL2
VCC
DD+
GND
2
4.7uF
DM1
DP1
2A
EN
nc
FLAG GND
C14
0.1uF
ESD/EMI Options (DNP)
2
4
2013 Microchip Technology Inc.
GND
1V2 A6
330
0.1uF
SHLD1
1
2
3
4
PWR2
DM2
DP2
C10
150uF
U2 AP2111SG_SO8
2
6
3 IN1 OUT1 7
IN2 OUT2
J21
3.3V Log.
3.3V IO
GND
GND
1.0uF
(*Note: Aardvark has
default 2.2K pull ups
on its SDA and SCL.)
R1
Port
1
VDD33 (4.7 uF)
C24
4.7uF
3V3
6
7
8
9
10
11
C1
J2
R68
B5
S1
S2
S3
S4
S5
S6
INT#
PRTPWRA/OCSA/PRTCTLA
5V
D1
Br_Grn-RA
"PPWR1"
D1
ZERO
ZERO
ChrgDet0
2
1 J19
1 J18
2
A1
R5
2.2K
8
1
C13
0.1uF
DATA3
ChrgDet1
SPI_CLK
SPI_DO/SPI_SPD_SEL
SPI_DI
SPI_CE
2A
EN
nc
FLAG GND
WHITE TP10
C9
150uF
VBUS
DD+
ID
GND
J20
2
3
D4
E4
1
U.FL
R64
R67
RESET
RBIAS
CHRGDET0
CHRGDET1
J1 USB uAB
1
2
3
4
5
PWR1_3
DM1
DP1
100uF
ZERO
ZERO
U1 AP2111SG_SO8
2
6
3 IN1 OUT1 7
IN2 OUT2
Downstream
REFSEL0
REFSEL1
SUSP/IRQ/INT
(*short)
SCL/SMBCLK
SDA/SMBDATA
RESET#
HUB_CONN
INT#
(scl)
(sda)
(gpio)
(gpio)
(gpio)
REFCLK
J11 (*open)
1
C26
(gnd) 2
(dnc) 4
(dnc) 6
(gpio) 8
(gnd) 10
D2
D3
E2
E1
SPI_SCK
SPI_MOSI
SPI_MISO
SPI_CE#
Dual-Output SPI Flash
SPI
DM2
DP2
R16
12.0K
1%
10K
10K
10K
R61
R62
2
4
74LVC1G14
R31
R71
"Reset"
D6
2.2K
Br_Red-RA
3
3V3
3
DMD1
DPS1
Downstream
(Swap)
OSC1
12MHz
OSCILLATOR
1
C5
B6
SW1
-RESET-
3
4
1
1
2
J7
2
Ext_Rst
Shdn
Cdelay
C35
4
2
3
USB3613_WLCSP30
HUB_CONN
5
B1
DNP
GND
TP13
RED
Warning:
Downstream VBUS is
5V @ 2A per channel to
support Battery Charging.
+
J23
TP16
BLACK
Br_Red-RA
"5V Present"
2
D5
2
HUB_CONN
Hub_Conn (3V3 levels)
+
R20
2.2K
3
3
1
2.1 mm
5V
Note:
Jumper defaults are
indicated with an "*".
100K
5
R43
2
J8
EVB-USB3613 EVALUATION BOARD SCHEMATIC
0.1uF
(delay=
~300 ms)
ADJ
PWRGD
7
5
(load=
17.5 uA)
100K
3V3
R24
150K
1%
TP12
ORANGE
C31
C30
4.7uF 0.1uF
R23
21.0K
1%
EVB-USB3613 Evaluation Board User’s Guide
DS50002194A-page 26
FIGURE B-1:
EVB-USB3613
EVALUATION BOARD
USER’S GUIDE
Appendix C. Bill of Materials (BOM)
C.1
INTRODUCTION
This appendix includes the EVB-USB3613 Evaluation Board Bill of Materials (BOM).
2013 Microchip Technology Inc.
DS50002194A-page 27
Item Qty
EVB-USB3613 EVALUATION BOARD BILL OF MATERIALS
Qty
Populated
Reference Designator(s)
Description
Manufacturer
1
2
2
C9, C10
Capacitor, Low ESR, 150uF, 6.3 VDC, 20%,
Aluminum, Radial-SMT, 5mm x 5.7mm
Lelon
2
1
1
C1
Capacitor, 0.1uF, 25V, 10%, X5R, 0402
3
6
6
C2, C13, C14, C21, C30, C35
4
1
1
5
2
2
6
3
7
Manufacturer Part Number
Notes
VZS151M0JTR-0506
‘3613
Murata Electronics®
GRM155R61E104KA7D
‘3613
Capacitor, 0.1uF, 25V, 10%, X5R, 0402
Murata Electronics
GRM155R61E104KA7D
C63
Capacitor, 0.1uF, 10V, 10%, X5R, 0402
Murata Electronics
GRM155R71A104KA01D
C24, C42
Capacitor, 1.0uF, 16 VDC, 10%, X5R, 0603
Murata Electronics
GRM188R61C105KA93D
3
C26, C31, C33
Capacitor, 4.7uF, 6.3 VDC, 20%, X5R, 0603
Murata Electronics
GRM188R60J475KE19D
4
4
R61, R62, R64, R67
Resistor, ZERO, 0.1W, 0402
Panasonic®
ERJ-2GE0R00X
‘3613
8
1
1
R68
Resistor, ZERO, 0.1W, 0402
Panasonic
ERJ-2GE0R00X
PCTL
9
1
1
R1
Resistor, 330, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ331V
‘3613
10
1
1
R2
Resistor, 330, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ331V
11
6
6
R5, R6, R7, R20, R57, R71
Resistor, 2.2K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ222V
12
1
1
R16
Resistor, 12.0K, 1%, 1/16W, 0603
Panasonic
ERJ-3EKF1202V
13
7
7
R26, R32, R33, R38, R40, R41,
R42
Resistor, 10K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ103V
14
2
2
R21, R25
Resistor, 10K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ103V
15
1
1
R23
Resistor, 21.0K, 1%, 1/16W, 0603
Yageo America
9C06031A2102FKHFT
16
1
1
R24
Resistor, 150K, 1%, 1/10W, 0603
Panasonic
ERJ-3EKF1503V
17
1
1
R43
Resistor, 100K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ104V
18
2
2
R30, R31
Resistor, 100K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ104V
19
1
1
R69
Resistor, 33, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ330V
2013 Microchip Technology Inc.
20
4
4
D1, D2, D3, D18
LED, Green, Bright (40 mcd), 0804, Right Angle
Stanley Electric
DG1113F
21
2
2
D5, D6
LED, Bright Red, 0804, Right Angle
Stanley Electric
FR1113F
22
1
1
J8
Connector, Power Jack, 2.1 mm x 5.5 mm, 12V, 4A,
Right Angle, TH
Cui Stack
PJ-002AH
23
1
1
J1
Receptacle, USB, Micro-AB, Right Angle, SMT
Hirose
ZX62-AB-5PA(11)
24
1
1
J2
Receptacle, USB, Style A, Right Angle, Through-hole
AMP
292303-1
25
4
4
J14, J15, J20, J21
Receptacle, Coax, U.FL, SMT, Vertical
Hirose
U.FL-R-SMT-1
26
1
1
J54
Receptacle, SMA, Vertical
AMP
221789-1
27
2
2
J7, J33
Header, 1x2, 0.1 Inch, Vertical (cut from 1x36)
Samtec
TSW-102-14-L-S
28
1
1
J23
Header, 1x2, 0.1 Inch, Vertical
Samtec
TSW-102-14-L-S
29
5
5
J11, J12, J18, J19, J22
Header, 2x1, 0.1 Inch, Vertical (cut from 2x36)
Samtec
TSW-102-14-L-S
EEPROM
‘3613
‘3613
‘3613
‘3613
EVB-USB3613 Evaluation Board User’s Guide
DS50002194A-page 28
TABLE C-1:
2013 Microchip Technology Inc.
TABLE C-1:
Item Qty
30
1
EVB-USB3613 EVALUATION BOARD BILL OF MATERIALS
Qty
Populated
1
Reference Designator(s)
Description
Manufacturer
Manufacturer Part Number
J13
Header, 2x5, 0.1 Inch, Vertical
AMP
146256-5
31
1
1
SW1
Switch, Momentary, SPST, 100mA, J-lead, NO
E-Switch
TL3301xF160QJor-RJ
32
2
2
TP3, TP10
Test Point, White, Loop, Mini, 0.04 Inch ID
Keystone
5002
33
4
4
TP5, TP7, TP9, TP16
Test Point, Black, Loop, Mini, 0.04 Inch ID
Keystone
5001
34
2
2
TP6, TP12
Test Point, Orange, Loop, Mini, 0.04 Inch ID
Keystone
5003
5000
1
1
TP13
Test Point, Red, Loop, Mini, 0.04 Inch ID
Keystone
36
1
1
TP15
Test Point, Yellow, Loop, Mini, 0.04 Inch ID
Keystone
5004
37
1
1
U0
IC, USB3613, 3-Port USB 2.0/HSIC Hub, WLCSP30
Standard
Microsystems Corp
USB3613
38
2
2
U1, U2
IC, AP2111SG-13, Power Distribution Switch, SOP-8
Diodes® Inc.
AP2111SG-13
39
1
1
U6
IC, MCP1725-ADJE/SN, LDO Regulator, Adj., 500
mA, SOIC8
Microchip
Technology
MCP1725(T)-ADJE/SN
40
2
2
U9, U14
IC, 74LVC1G14, Inverter, Shottky, DCK
TI
SN74LVC1G14DCKR
41
1
1
U17
IC, ‘25VF640C, 64Mb, (8M x 8) SPI Serial FLASH,
2.5V-3.6V, 75-80 MHz, Dual Read, SO8
Microchip
SST25VF064C-80-4I-S3AE
42
1
1
OSC1
Oscillator, 12.000 MHz, 50 ppm, 3.3V, SMT
CTS
CB3LV-3C-12M0000
43
4
4
Foot, Silicone Rubber, Adhesive, Clear, Cylindrical
.375” x .190”
Richco®
RBS-35
44
1
1
45
1
1
46
1
1
Starting SN = Band-01
Serial Number Labels, 6 mm x 27 mm
PCB, Band (EVB-USB3x13), Rev. A
SPI
Place bottom
side, one at
each corner
Place bottom
side in white
S/N box
Assy Labels: “EVB-USB3613_A1”, 6 mm x 27 mm
PCB Fab
SMBus
EVB-USB3x13
Place top side
in Assy# box
ViaSystems/DDi
EVB-USB3x13
Supplied by
SMSC
DS50002194A-page 29
47
1
1
Assembly
Assembly, Band (EVB-USB3613), Rev. A1
48
1
0
C25
Capacitor, Low ESR, 100uF, 6.3 VDC, 20%,
Aluminum, Radial-SMT, 5 mm x 5.8 mm
United Chemi-Con
EMZA6R3ADA101ME61G
DNP
49
1
0
C11
Capacitor, Low ESR, 150uF, 6.3 VDC, 20%,
Aluminum, Radial-SMT, 5 mm x 5.7 mm
Lelon
VZS151M0JTR-0506
‘3813
50
2
0
C3, C41
Capacitor, 0.1uF, 25V, 10%, X5R, 0402
Murata Electronics
GRM155R61E104KA7D
‘3813
51
3
0
C5, C6, C7
Capacitor, 0.1uF, 25V, 10%, X5R, 0402
Murata Electronics
GRM155R61E104KA7D
ESD
52
1
0
C34
Capacitor, 0.1uF, 25V, 10%, X5R, 0402
Murata Electronics
GRM155R61E104KA7D
EEPROM-DNP
53
2
0
C38, C39
Capacitor, 1000pF, 50V, 10%, X7R, 0402
Murata Electronics
GRM155R71H102KA01D
‘3813
Bill of Materials (BOM)
35
Notes
Item Qty
EVB-USB3613 EVALUATION BOARD BILL OF MATERIALS
Qty
Populated
Reference Designator(s)
Description
Manufacturer
Manufacturer Part Number
Notes
54
1
0
C37
Capacitor, 1.0uF, 16VDC, 10%, X5R, 0603
Murata Electronics
GRM188R61C105KA93D
DNP
55
1
0
C40
Capacitor, 2.2uF, 6.3 VDC, 10%, X5R, 0603
Murata Electronics
GRM185R60J225KE26D
‘3813
56
6
0
R58, R59, R60, R63, R65, R66
Resistor, ZERO, 0.1W, 0402
Panasonic
ERJ-2GE0R00X
‘3813
57
2
0
R3, R36
Resistor, 330, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ331V
‘3813
58
2
0
R17, R19
Resistor, 10K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ103V
DNP
59
1
0
R29
Resistor, 100K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEY104V
‘3813
60
1
0
R34
Resistor, 82K, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ823V
‘3813
61
1
0
R70
Resistor, 33, 5%, 1/16W, 0603
Panasonic
ERJ-3GEYJ330V
DNP
62
1
0
J0
Receptacle, USB, Micro-AB, Right Angle, SMT
Hirose
ZX62-AB-5PA
‘3813
63
1
0
J3
Receptacle, USB, Style A, Right Angle, Through-hole
AMP
292303-1
‘3813
64
2
0
J16, J17
Receptacle, Coax, U.FL. SMT, Vertical
Hirose
U.FL-R-SMT-1
‘3813
65
1
0
J9
Header, 1x2, 0.1 Inch, Vertical
Samtec
TSW-102-14-L-S
‘3813
66
3
0
BR1, BR2, BR3
Diode, Bridge, Switching, 50V, 140 mA, KCAC,
SOT-143
Infineon Tech
BGX50A
ESD
67
3
0
L1, L2, L3
Inductor, Common Mode Choke, DLP11SN900SL2,
0504
Murata Electronics
DLP11SN900SL2
ESD
68
1
0
SKT1 (Place at U8)
Socket, IC, 8-Pin DIP, Leaf Contacts, Through-hole
Assmann
A08-LC-TT-R
EEPROM-DNP
69
1
0
TP11
Test Point, White, Loop, Mini, 0.04 Inch ID
Keystone
5002
‘3813
70
1
0
U8
IC, 24C04, 2 Wire Serial EPROM, 4 Kb, 2.7V, DIP-8
Microchip
Technology
24LC04B-I/P
EEPROM-DNP
71
1
0
SHUNT1
Shunt, Insulated, 0.1 Inch
AMP
881545-2
DNP
EVB-USB3613 Evaluation Board User’s Guide
DS50002194A-page 30
TABLE C-1:
2013 Microchip Technology Inc.
Worldwide Sales and Service
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hangzhou
Tel: 86-571-2819-3187
Fax: 86-571-2819-3189
China - Hong Kong SAR
Tel: 852-2943-5100
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8864-2200
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
India - Pune
Tel: 91-20-3019-1500
Japan - Osaka
Tel: 81-6-6152-7160
Fax: 81-6-6152-9310
Japan - Tokyo
Tel: 81-3-6880- 3770
Fax: 81-3-6880-3771
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-5778-366
Fax: 886-3-5770-955
Taiwan - Kaohsiung
Tel: 886-7-213-7828
Fax: 886-7-330-9305
Taiwan - Taipei
Tel: 886-2-2508-8600
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
DS50002194A-page 31
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
08/20/13
2013 Microchip Technology Inc.