SAW Bandpass Filter F1G88 Features RF bandpass filter High attenuation No matching single-ended operation Ceramic Surface Mounted Device Package ( 3.0 mm × 3.0 mm ) RoHS Compliant Package Dimension 1 I 1G88 2 3 6 6 1 5 5 2 4 4 3 Pin Configurations Dimensions shown are nominal in millimeters Body : Al2O3 Ceramic Lid : Kovar, Ni Plated Terminations : Au plating 0.3 ~ 1.0 um, Over a 1.27 ~ 8.89 um Ni Plating 2 Input 5 Output 1, 3, 4, 6 Case ground Maximum Ratings Parameters Unit Minimum Typical Maximum Operating Temperature Range ℃ -20 25 75 Storage Temperature Range ℃ -40 - 85 Power Handling Capability dBm - - 10 Electrostatics Sensitive Device (ESD) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 1/7 SAW Bandpass Filter F1G88 Specifications Fo = 1855.0 MHz Minimum Typical Maximum Unit Center Frequency ( Fc ) - 1855.0 - MHz Insertion Loss (In Fc ±15.0 MHz) - 2.2 3.0 dB Amplitude Ripple (In Fc ±15.0 MHz) - 0.6 1.5 dB VSWR (In Fc ±15.0 MHz) - 1.5 2.0 1440MHz ~ 1470MHz 25 37 - 1750MHz ~ 1780MHz 29 36 - 1930MHz ~ 1960MHz 30 40 - 2240MHz ~ 2270MHz 28 46 - Relative Attenuation Input/Output Impedance dB 50 Ohm Notes : 1) All specifications are based on the matching schematic shown below 2) All specifications are measured by Agilent Network analyzer and full 2 port calibration at room temperature 3) All attenuation measurements are measured relative to insertion loss I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 2/7 SAW Bandpass Filter F1G88 Matching Schematic ( Actual matching values may vary due to PCB layout and parasitics ) Input 50Ω Output 50Ω Marking Configuration 1) I2) 1G883) 1) Pad Number 1 Index 2) Manufacturer name 3) Marking Number * Ink or Laser Marking available I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 3/7 SAW Bandpass Filter F1G88 Typical Performance ( at +25℃ ℃) I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 4/7 SAW Bandpass Filter F1G88 I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 5/7 SAW Bandpass Filter F1G88 Packing Specification 1. Reeling Quantity : 3000 pcs / 13” reel ( or 1000 pcs / 7” reel ) 2. Taping Structure : The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE REEL CARRIER TAPE Tape Specification 1. Leader part and vacant position specification Vacant 150mm min. Component contained Vacant 150mm min. Leader part 250mm min. END START Tape Running Direction 2. Tensile strength of carrier tape 4.4N/mm width Direction of pull Top cover tape 3. Top cover tape adhesion 0~15 degree 1) pull off angle : 0~15° 2) speed : 300mm/min 3) force : 20~70g I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Carrier tape Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 6/7 SAW Bandpass Filter F1G88 Carrier Tape Dimensions [unit : mm] A 3.40 ± 0.1 B 3.40 ± 0.1 C 7.25 ± 0.1 D 1.70 ± 0.1 E 12.00 ± 0.1 F 8.00 ± 0.1 Part Direction Tape Running Direction Reel Dimensions [unit : mm] I T F Co., Ltd. 102-901, Bucheon Technopark 364, Samjeong-Dong, Ojeong-Gu, Bucheon-City, Gyounggi-Do, Korea 421-809 Part No. F1G88 Rev. Date 2014-03-19 Rev. NC9013-AS02 7/7