HI31466 8-Bit, 120 MSPS, Flash A/D Converter August 1997 Features Description • Differential Linearity Error . . . . . . . . . . . . . . . ±0.5 LSB • RGB Graphics Processing (LCD, PDP) The HI31466 is an 8-bit, high-speed, flash analog-to-digital converter optimized for high speed, low power, and ease of use. With a 120 MSPS encode rate capability and full-power analog bandwidth of 150MHz, this component is ideal for applications requiring the highest possible dynamic performance. To minimize system cost and power dissipation, only a +5V power supply is required. The HI31466’s clock input interfaces directly to TTL, ECL, or PECL logic and will operate with singleended inputs. The user may select 16-bit demultiplexed output or 8-bit single channel digital outputs. The demultiplexed mode interleaves the data through two 8-bit channels at 1/2 the clock rate. Operation in demultiplexed mode reduces the speed and cost of external digital interfaces, while allowing the A/D converter to be clocked to the full 120 MSPS conversion rate. Fabricated with an advanced Bipolar process, the HI31466 is provided in a space-saving 48-lead MQFP surface mount plastic package and is specified over the -20oC to 75oC temperature range. For a faster clock rate, please refer to the HI31466A (140 MSPS), AnswerFAX Document number 4246. • Digital Oscilloscopes Ordering Information • Integral Linearity Error . . . . . . . . . . . . . . . . . . ±0.5 LSB • Integral Linearity Compensation Circuit • Low Input Capacitance . . . . . . . . . . . . . . . . . . . . . . 21pF • Wide Analog Input Bandwidth . . . . . . . . . . . . . 150MHz • Low Power Consumption . . . . . . . . . . . . . . . . . .760mW • Internal 1/2 Frequency Divider Circuit (w/Reset Function) • CLK/2 Clock Output • Compatible with ECL, PECL and TTL Digital Input Levels • 1:2 Demultiplexed Output Pin • Surface Mounting Package Applications • Digital Communications (QPSK, QAM) PART NUMBER • Magnetic Recording (PRML) TEMP. RANGE (oC) HI31466JCQ -20 to 75 HI31466EVAL 25 Pinout P1D4 P1D7 P1D6 P1D5 DVCC2 DGND2 CLKOUT RESETN/T SELECT INV RESETN/E RESET/E HI31466JCQ (MQFP) TOP VIEW DVEE3 1 48 47 46 45 44 43 42 41 40 39 38 37 36 VRB AGND VRM1 2 3 35 34 P1D2 4 5 33 32 31 P1D0 DGND2 DVCC2 30 29 DVCC1 P2D3 P2D2 P2D0 P2D1 NC 11 25 12 13 14 15 16 17 18 19 20 21 22 23 24 CLK/E DGND3 26 DVCC2 DGND2 VRT 28 27 NC VRM3 AGND 8 9 10 CLK/T NC AVCC 6 7 CLKN/E AVCC VIN VRM2 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1 P1D3 P1D1 DGND1 P2D7 P2D6 P2D5 P2D4 PACKAGE PKG. NO. 48 Ld MQFP Q48.12x12-S Evaluation Board HI31466 Block Diagram AVCC 5 8 INV DVCC1 44 30 DVCC2 DGND3 19 31 42 12 VRT 11 R1 R/2 R (MSB) 40 P1D7 1 R 39 P1D6 2 6 BITS 38 P1D5 9 8 BITS R 64 37 P1D4 TTLOUT 63 VRM3 LATCHA R 36 P1D3 R 35 P1D2 65 6 BITS R 6-BIT LATCH AND ENCODER 34 P1D1 126 127 VRM2 7 VIN 6 R 128 ENCODER R R 129 33 P1D0 (LSB) 8 BITS (MSB) 28 P2D7 6 BITS R 27 P2D6 191 4 R 26 P2D5 LATCHB 192 R 193 TTLOUT VRM1 25 P2D4 24 P2D3 6 BITS R 23 P2D2 254 R 22 P2D1 255 R/2 VRB 2 CLK/T 15 CLK/E 13 21 P1D0 (LSB) R/2 DELAY 16 17 NC 18 CLKN/E 14 D Q 43 CLKOUT SELECT RESETN/T 46 RESETN/E 48 RESET/E 47 Q 3 10 45 AGND 29 SELECT DGND1 2 20 32 41 DGND2 1 DVEE3 HI31466 Absolute Maximum Ratings TA = 25oC Thermal Information Supply Voltage (AVCC , DVCC1, DVCC2) . . . . . . . . . . -0.5V to 7.0V (DGND3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7.0V (DVEE3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -7.0V to 0.5V (DGND3 - DVEE3) . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7.0V Analog Input Voltage (VIN) . . . . . . . . . . . . . . . . . VRT - 2.7V to AVCC Reference Input Voltage (VRT) . . . . . . . . . . . . . . . . . . .2.7V to AVCC (VRB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VIN - 2.7V to AVCC (|VRT - VRB|) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5V Digital Input Voltage ECL (***/E (Note 2)) . . . . . . . . . . . . . . . . . . . . . . . . DVEE3 to 0.5V PECL (***/E) . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DGND3 TTL (***/T, INV) . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DVCC1 Other (SELECT) . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to DVCC1 VID (|***/E - ***N/E| (Note 3)) . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V θJA (oC/W) Thermal Resistance (Typical, Note 1) MQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (Lead Tips Only) Recommended Operating Conditions WITH A SINGLE POWER SUPPLY MIN TYP MAX Supply Voltage DVCC1 , DVCC2 , AVCC . . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DGND1, DGND2, AGND . . . . . . . . . . . . . -0.05 0 +0.05V DGND3 . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DVEE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.05 0 +0.05V Analog Input Voltage (VIN) . . . . . . . . . . . . . . VRB VRT Reference Input Voltage VRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.9 +4.1V VRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 +2.6V |VRT - VRB| . . . . . . . . . . . . . . . . . . . . . . . . 1.5 2.1V Digital Input Voltage PECL (***/E) VIH . . . . . . . . . . . . . . . DGND3 - 1.05 DGND3 - 1.4V PECL (***/E) VIL . . . . . . . . . . . . . . . DGND3 - 3.2 DGND3 - 1.4V TTL (***/T, INV) VIH. . . . . . . . . . . . . . . . . . 2.0V TTL (***/T, INV) VIL . . . . . . . . . . . . . . . . . . 0.8V Other (SELECT) VIH . . . . . . . . . . . . . . . . . DVCC1 Other (SELECT) VIL . . . . . . . . . . . . . . . . . DGND1 VID (Note 3) (|***/E- ***N/E|). . . . . . . . . . . 0.4 0.8 Max Conversion Rate (fC , Straight Mode) . . . 100 MSPS Max Conversion Rate (fC , DMUX Mode) . . . . 120 MSPS Ambient Temperature (TA) . . . . . . . . . . . . . . . . . . . . . -20oC to 75oC WITH DUAL POWER SUPPLIES MIN TYP MAX Supply Voltage DVCC1 , DVCC2 , AVCC . . . . . . . . . . . . . . +4.75 +5.0 +5.25V DGND1, DGND2, AGND . . . . . . . . . . . . . -0.05 0 +0.05V DGND3 . . . . . . . . . . . . . . . . . . . . . . . . . . -0.05 0 +0.05V DVEE3 . . . . . . . . . . . . . . . . . . . . . . . . . . . -5.5 -5.0 -4.75V Analog Input Voltage (VIN) . . . . . . . . . . . . . VRB VRT Reference Input Voltage VRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.9 +4.1V VRB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 +2.6V |VRT - VRB| . . . . . . . . . . . . . . . . . . . . . . . 1.5 2.1V Digital Input Voltage ECL (***/E) VIH . . . . . . . . . . . . . . . . DGND3 - 1.05 DGND3 - 0.5V ECL (***/E) VIL . . . . . . . . . . . . . . . . DGND3 - 3.2 DGND3 - 1.4V TTL (***/T, INV) VIH . . . . . . . . . . . . . . . . . 2.0V TTL (***/T, INV) VIL . . . . . . . . . . . . . . . . . 0.8V Other (SELECT) VIH . . . . . . . . . . . . . . . . DVCC1 Other (SELECT) VIL . . . . . . . . . . . . . . . . DGND1 VID (Note 3) (|***/E- ***N/E|) . . . . . . . . . . 0.4 0.8 Max Conversion Rate (fC , Straight Mode) . . . 100 MSPS Max Conversion Rate (fC , DMUX Mode) . . . . 120 MSPS Ambient Temperature (TA). . . . . . . . . . . . . . . . . . . . . .-20oC to 75oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured with the component mounted on an evaluation PC board in free air. 2. ***/E and ***T indicate CLK/E and CLK/T, etc., for the pin name. 3. VID : Input Voltage Differential. Electrical Specifications PARAMETER DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC TEST CONDITIONS MIN TYP MAX UNITS - 8 - Bits - - ±0.5 LSB - - ±0.5 LSB - 21 - pF Analog Input Resistance, RIN 4 - 50 kΩ Analog Input Current, IIN 0 - 500 µA Resolution DC CHARACTERISTICS Integral Linearity Error, EIL VIN = 2VP-P , fC = 5 MSPS Differential Linearity Error, EDL ANALOG INPUT Analog Input Capacitance, CIN VIN = +3.0V +0.07VRMS 3 HI31466 Electrical Specifications DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Reference Resistance (Note 4), RREF 75 115 155 Ω Reference Current (Note 5), IREF 9.7 17.4 28 mA Offset Voltage VRT Side, EOT 2 - 15 mV Offset Voltage VRB Side, EOB 2 - 10 mV Digital Input Voltage: High, VIH DGND3 - 1.05 - DGND3 - 0.5 V Digital Input Voltage: Low, VIL DGND3 - 3.2 - DGND3 -1.4 V REFERENCE INPUT DIGITAL INPUT (ECL, PECL) - DGND3 - 1.2 - V Digital Input Current: High, IIH VIH = DGND3 - 0.8V -50 - +50 µA Digital Input Current: Low, IIL VIL = DGND3 - 1.6V -75 - 0 µA - - 5 pF Digital Input Voltage: High, VIH 2.0 - - V Digital Input Voltage: Low, VIL - - 0.8 V Threshold Voltage, VTH - 1.5 - V Threshold Voltage, VTH Digital Input Capacitance DIGITAL INPUT (TTL) Digital Input Current: High, IIH VIH = 3.5V -50 - 0 µA Digital Input Current: Low, IIL VIL = 0.2V -500 - 0 µA - - 5 pF Digital Input Capacitance DIGITAL OUTPUT (TTL) Digital Output Voltage: High, VOH IOH = -2mA 2.4 - - V Digital Output Voltage: Low, VOL IOL = 1mA - - 0.5 V 120 - - MSPS SWITCHING CHARACTERISTICS Maximum Conversion Rate, fC DMUX Mode Aperture Jitter, tAJ - 10 - ps Sampling Delay, tDS 3 4.5 6 ns Clock High Pulse Width, tPW1 CLK 3.2 - - ns Clock Low Pulse Width, tPW0 CLK 3.2 - - ns Reset Pulse Width, tPWR (Note 6) RESETN tx2 - - ns RESET Signal Setup Time, tRS RESETN-CLK 3.5 - - ns RESET Signal Hold Time, tRH RESETN-CLK 0 - - ns CLKOUT Output Delay, tDCLK (CL = 5pF) 3.5 7 9 ns Data Output Delay (Note 6), tDO1 tDO2 DEMUX Mode (CL = 5pF) Output Rise Time, tr Output Fall Time, tf t t+1 t+2 ns (CL = 5pF) 4.5 8 10 ns 0.8 to 2.0V (CL = 5pF) - 2 - ns 0.8 to 2.0V (CL = 5pF) - 2 - ns 150 - - MHz DYNAMIC CHARACTERISTICS Input Bandwidth VIN = 2VP-P , -3dB S/N Ratio fC = 120 MSPS, fIN = 1kHz Full Scale, DMUX Mode - 46 - dB fC = 120 MSPS, fIN = 29.999MHz Full Scale, DMUX Mode - 40 - dB 4 HI31466 Electrical Specifications DVCC1 , 2 , AVCC , DGND3 = +5V, DGND1, 2, AGND, DVEE3 = 0V, VRT = 4V, VRB = 2V, TA = 25oC (Continued) PARAMETER TEST CONDITIONS MIN TYP MAX UNITS TPS fC = 120 MSPS, fIN = 1kHz Full Scale, DMUX Mode, Error > 16 LSB - - 10-12 fC = 120 MSPS, fIN = 29.999MHz Full Scale, DMUX Mode, Error > 16 LSB - - 10-9 TPS fC = 100 MSPS, fIN = 24.999MHz Full Scale, Straight Mode, Error > 16 LSB - - 10-9 TPS Supply Current, ICC 125 145 185 mA Supply Current, IEE 0.4 0.6 0.8 mA Power Consumption (Note 8), PD 660 760 960 mW Error Rate (Note 7) POWER SUPPLY NOTES: 4. RREF: Resistance value between VRT and VRB . V RT – V RB 5. I REF = ---------------------------R REF . 1 6. T = ----- . fC 7. The unit of measure TPS: Times Per Sample. ( V RT – V RB ) 2 -. 8. P D = ( I CC + I EE ) • V CC + -----------------------------------V REF Timing Diagrams N-1 VIN N+2 N+3 tDS N N+1 t CLK tPW1 tD02 tPW0 2V N-2 P1D0 TO D7 N N+2 N-1 N-1 0.8V P2D0 TO D7 2V N-3 0.8V tD01 tDCLK t + 1ns CLK OUT 2V 2V 0.8V 0.8V RESET PULSE tPWR FIGURE 1. DEMUX MODE TIMING CHART (SELECT = VCC) 5 HI31466 Timing Diagrams N+2 N-1 VIN N+3 N+1 tDS N t CLK tPW1 tPW0 P1D0 TO D7 N-4 2.0V 0.8V N-3 N-2 N-1 N P2D0 TO D7 N-5 2.0V 0.8V N-4 N-3 N-2 N-1 tD02 8ns 2.0V CLK OUT (CLK IS INVERTED AND OUTPUT) 0.8V tDCLK RESET PULSE FIGURE 2. STRAIGHT MODE TIMING CHART (SELECT = GND) DGND3 VIH (MAX) VIL VTH (DGND3 - 1.2V) VID VIH VIL (MIN) FIGURE 3. ECL AND PECL SWITCHING LEVEL Pin Descriptions I/O TYPICAL VOLTAGE LEVEL PIN NO SYMBOL EQUIVALENT CIRCUIT 3, 10 AGND GND Analog Ground. Separated from the digital ground. 5, 8 AVCC +5V (Typ) Analog Power Supply. Separated from the digital power supply. 20, 29 32, 41 DGND1 DGND2 GND Digital Ground. 19, 30 31, 42 DVCC1 DVCC2 +5V (Typ) Digital Power Supply. 12 DGND3 +5V (Typ) (With a Single Power Supply) Digital Power Supply. Ground for ECL input. -5V for PECL and TTL input. GND (With Dual Power Supplies) 6 DESCRIPTION HI31466 Pin Descriptions (Continued) PIN NO SYMBOL 1 DVEE3 I/O TYPICAL VOLTAGE LEVEL EQUIVALENT CIRCUIT GND (With a Single Power Supply) DESCRIPTION Digital Power Supply. Ground for ECL input. -5V for PECL and TTL input. +5V (Typ) (With Dual Power Supplies) 16, 17, 18 NC 13 CLK/E 14 CLK/NE No Connect pin. Not connected with the internal circuits. I ECL/PECL Clock Input. DGND3 I R R 13 48 14 47 I 47 RESET/E I Reset Input. When the input is set to low level, the built-in CLK frequency divider circuit can be reset. 1.2V R RESETN/E R 48 DVEE3 15 CLK/T I 46 RESETN/T I CLK/E Complementary Input. When left open, this pin goes to the threshold potential. Only CLK/E can be used for operation, but complementary input is recommended to attain fast and stable operation. TTL RESETN/E Complementary Input. When left open, this pin goes to the threshold voltage. Only RESETN/E can be used for operation. Clock input. DVCC1 R/2 15 46 R Reset Input. When left open, this input goes to high level. When the input is set to low level, the built-in CLK frequency divider circuit can be reset. 1.5V DGND1 DVEE3 44 INV I TTL Data Output Polarity Inversion Input. When left open, this input goes to high level. (See Table 1; I/O Correspondence Table). DVCC1 44 DGND1 DVEE3 45 SELECT VCC or Ground Data Output Mode Selection. (See Table 2; Operating Mode Table). DVCC1 45 DGND1 DVEE3 7 HI31466 Pin Descriptions (Continued) PIN NO SYMBOL I/O 11 VRT I TYPICAL VOLTAGE LEVEL EQUIVALENT CIRCUIT DESCRIPTION 4.0V (Typ) Top Reference Voltage. Bypass to AGND with a 1µF tantal capacitor and a 0.1µF chip capacitor. R1 11 9 7 4 VRM3 VRB + 2 --- (VRT - VRB) 4 VRM2 VRM1 VRB Reference Voltage Mid Point. Bypass to AGND with a 0.1µF chip capacitor. R COMPARATOR 1 R COMPARATOR 63 9 R I COMPARATOR 127 R 7 Reference Voltage Mid Point. Bypass to AGND with a 0.1µF chip capacitor. COMPARATOR 64 VRB + 1 (V - V ) --RT RB 4 2 R/2 VRB + 3 --- (VRT - VRB) 4 Reference Voltage Mid Point. Bypass to AGND with a 0.1µF chip capacitor. COMPARATOR 128 COMPARATOR 191 2.0V (Typ) 4 R COMPARATOR 192 Bottom Reference Voltage. Bypass to AGND with a 1µF tantal capacitor and a 0.1µF chip capacitor. R COMPARATOR 255 R/2 2 R2 6 VIN I VRT to VRB Analog Input. COMPARATOR AVCC AVCC 6 VREF AGND DVEE3 33 to 40 P1D0 to P1D7 O 21 to 28 P2D0 to P2D7 O 43 CLKOUT O TTL Port 1 Side Data Output. Port 2 Side Data Output. DVCC1 DVCC2 Clock Output. (See Table 2; Operating Mode Table). 21 TO 28 100K 33 TO 40 DGND1 43 DGND2 DVEE3 8 HI31466 - To prevent interference between AGND and DGND and between AVCC and DVCC , make sure the respective patINV terns are separated. To prevent a DC offset in the power supply pattern, connect the AVCC and DVCC lines at one 1 0 point each, via a ferrite-bead filter. Shorting the AGND VIN STEP D7 D0 D7 D0 and DGND patterns in one place immediately under the 255 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 VRT A/D converter improves A/D converter performance. - Ground the power supply pins (AVCC , DVCC1 , DVCC2 , 254 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 DVEE3) as close to each pin as possible with a 0.1µF or • • • larger ceramic chip capacitor. (Connect the AVCC pin to • • • the AGND pattern and the DVCC1 , DVCC2 , DVEE3 pins • • • to the DGND pattern). VRM2 128 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 - The digital output wiring should be as short as possible. 127 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 If the digital output wiring is long, the wiring capacitance will increase, deteriorating the output slew rate and • • • resulting in reflection to the output waveform since the • • • • • • original output slew rate is quite fast. • The analog input pin V IN has an input capacitance of 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 approximately 21pF. To drive the A/D converter with VRB 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 proper frequency response, it is necessary to prevent performance deterioration due to parasitic capacitance or Notes on Operation parasitic inductance by using a large capacity drive circuit; keeping wiring as short as possible, and using chip parts • The HI31466 is a high-speed A/D converter which is capable for resistors and capacitors, etc. of TTL, ECL and PECL level clock input. Characteristic impedance should be properly matched to ensure optimum • The VRT and VRB pins must have adequate bypass to protect them from high-frequency noise. Bypass them to performance during high-speed operation. AGND with approximately 1µF tantal capacitor and, 0.1µF • The power supply and grounding have a profound influence capacitor. At this time, approximately DGND3 - 1.2V voltage on converter performance. The power supply and groundis generated. However, this is not recommended for use as ing method are particularly important during high-speed threshold voltage VBB as it is too weak. operation. General points for caution are as follows: - The ground pattern should be as large as possible. It is When the digital input level is ECL or PECL level, ***/E pins recommended to make the power supply and ground should be used and ***/T pins left open. When the digital patterns wider at an inner layer using a multi-layer input level is TTL, ***/T pins should be used and III/E pins left open. board. TABLE 1. A/D CODE TABLE Test Circuits +V 4V 1.95V VRT 5V 5V A ICC A AVCC DVCC1 DVCC2 VIN S2 - IEE VRB -V CLK/E DGND2 DGND1 AGND S1: ON WHEN A < B S2: ON WHEN A > B DGND3 A<B A>B COMPARATOR 5MHz PECL VIN 2V S1 + DVEE3 8 HI31466 “0” A8 TO A1 B8 TO B1 A0 B0 8 BUFFER “1” DVM CONTROLLER 000...00 TO 111..10 FIGURE 5. INTEGRAL LINEARITY ERROR/DIFFERENTIAL LINEARITY ERROR MEASUREMENT CIRCUIT FIGURE 4. CURRENT CONSUMPTION MEASUREMENT CIRCUIT 9 HI31466 Test Circuits (Continued) VIN SIGNAL SOURCE 8 HI31466 A LATCH COMPARATOR A>B PULSE COUNTER B fC 4 CLK -1kHz CLK + LATCH 2VP-P SINE WAVE 16 LSB SIGNAL SOURCE 1/ 8 fC FIGURE 6. ERROR RATE MEASUREMENT CIRCUIT VRT VIN VRM2 100MHz VRB AMP CLK OSC1 φ: VARIABLE fR VIN 8 HI31466 ∆υ 129 ∆t 128 127 VIN LOGIC ALALYZER (LSB) 126 125 CLK 1024 SAMPLES σ CLK OSC2 SAMPLING TIMING FLUCTUATION (= APERTURE JITTER) NOTE: Where σ (LSB) is the deviation of the output codes when the largest slew rate point is sampled at the clock which has exactly the same frequency as the analog input signal, the aperture jitter tAJ is: ∆υ 256 t AJ = σ / ------- = σ/ ---------- x 2πf . 2 ∆t ECL BUFFER 100MHz FIGURE 7. SAMPLING DELAY/APERTURE JITTER MEASUREMENT CIRCUIT FIGURE 8. APERTURE JITTER MEASUREMENT METHOD Operating Modes The HI31466 has two types of operating modes which are selected with Pin 45 (SELECT). TABLE 2. OPERATING MODE TABLE OPERATING MODE SELECT MAXIMUM CONVERSION RATE DMUX Mode VCC 120 MSPS Demultiplexed Output 60 MBPS The input clock is 1/2 frequency divided and output at 60MHz. Straight Mode GND 100 MSPS Straight Output 100 MBPS The input clock is inverted and output at 100MHz. DATA OUTPUT DMUX Mode (See Application Circuits, Figures 18, 19, 20) Set the SELECT pin to VCC for this mode. In this mode, the clock frequency is divided by 2 in the IC, and the data is output after being demultiplexed by this 1/2 frequency divided clock. The 1/2 frequency divided clock, which has adequate setup time and hold time for the output data, is output from the CLKOUT pin. CLOCK OUTPUT termeasure, the HI31466 is equipped with a function which resets the 1/2 frequency divided clock. When resetting this clock, the RESET pulse must be input to the RESET pin. See the Timing Charts for the RESET pulse input timing. The A/D converter can operate at fC (Min) = 120 MSPS in this mode. Straight Mode (See Application Circuits, Figures 21, 22, 23) Set the SELECT pin to GND for this mode. In this mode, data When using multiple HI31466 units in parallel in this mode, difoutput can be obtained in accordance with the clock frequency 1 ferences in the start timing of the /2 frequency divided clock applied to the A/D converter for applications which use the may cause operation as shown in the figure below. As a counclock applied to the A/D converter as the system clock. 10 HI31466 The A/D converter can operate at fC (Min) = 100 MSPS in this mode. Digital Input Level and Supply Voltage Settings The logic input level for the HI31466 supports ECL, PECL and TTL levels. TABLE 3. LOGIC INPUT LEVEL AND POWER SUPPLY SETTINGS DIGITAL INPUT LEVEL DVEE3 The power supplies (DVEE3 , DGND3) for the logic input block must be set to match the logic input (CLK and RESET signals) level. DGND3 SUPPLY VOLTAGE APPLICATION CIRCUITS ECL -5V 0V 5V Figures 18, 21 PECL 0V +5V +5V Figures 19, 22 TTL 0V +5V +5V Figures 20, 23 CLK HI31466 CLK CLK CLKOUT A 8 BITS DATA RESETN HI31466 CLK CLKOUT B 8 BITS DATA RESETN FIGURE 9. WHEN THE RESET PULSE IS NOT USED CLK RESET PULSE HI31466 CLK CLK CLKOUT A 8 BITS DATA RESETN HI31466 CLK RESET PULSE CLKOUT B 8 BITS DATA RESETN FIGURE 10. WHEN THE RESET PULSE IS USED Typical Performance Curves 170 CURRENT CONSUMPTION (mA) CURRENT CONSUMPTION (mA) 170 160 150 140 150 140 fCLK -1kHz 4 DMUX MODE CL = 5pF fIN = 130 130 -25 160 25 75 AMBIENT TEMPERATURE (oC) 0 60 120 CONVERSION RATE (MSPS) FIGURE 11. CURRENT CONSUMPTION vs AMBIENT TEMPERATURE CHARACTERISTICS FIGURE 12. CURRENT CONSUMPTION vs CONVERSION RATE CHARACTERISTICS RESPONSE 11 HI31466 (Continued) VRT = 4V VRB = 2V 20 REFERENCE CURRENT (mA) ANALOG INPUT CURRENT (µA) Typical Performance Curves 200 100 15 10 0 2 3 -25 4 25 ANALOG INPUT VOLTAGE (V) FIGURE 13. ANALOG INPUT CURRENT vs ANALOG INPUT VOLTAGE CHARACTERISTICS FIGURE 14. REFERENCE CURRENT vs AMBIENT TEMPERATURE CHARACTERISTICS 50 fC = 120 MSPS ERROR RATE (TPS) 10-6 40 30 fIN = fCLK -1kHz 4 ERROR > 16 LSB 10-7 10-8 10-9 10-10 20 1 3 5 10 30 120 50 FIGURE 15. SNR vs INPUT FREQUENCY RESPONSE 170 fIN = 140 CONVERSION RATE (MSPS) INPUT FREQUENCY (MHz) MAXIMUM CONVERSION (MSPS) SNR (dB) 75 AMBIENT TEMPERATURE (oC) FIGURE 16. ERROR RATE vs CONVERSION RATE CHARACTERISTICS fCLK -1kHz 4 ERROR > 16 LSB ERROR RATE: 10-9 TPS 160 150 140 130 -25 25 75 AMBIENT TEMPERATURE (Co) FIGURE 17. MAXIMUM CONVERSION RATE vs AMBIENT TEMPERATURE CHARACTERISTICS 12 160 HI31466 Application Circuits +5V (D) DG ECL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 -5V (D) 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 AG AG 2V +5V (A) DG 4V 12 LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH 13 14 15 16 17 18 19 20 21 22 23 24 ECL - CLK DG +5V (D) FIGURE 18. DMUX ECL INPUT +5V (D) DG PECL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 DG 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 DG AG 2V +5V (A) +5V (D) 4V 12 13 14 15 16 17 18 19 20 21 22 23 24 PECL - CLK DG +5V (D) FIGURE 19. DMUX PECL INPUT 13 LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH HI31466 Application Circuits (Continued) +5V (D) DG TTL RESET PULSE 48 47 46 45 44 43 42 41 40 39 38 37 DG 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 P2D0 TO P2D7 8-BIT DIGITAL DATA 25 1 AG 2V AG +5V (A) 4V +5V (D) 12 LATCH DG +5V (D) DG 8-BIT DIGITAL DATA LATCH 13 14 15 16 17 18 19 20 21 22 23 24 TTL - CLK DG +5V (D) FIGURE 20. DMUX TTL INPUT DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 -5V (D) 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 1 AG AG 2V +5V (A) DG 4V DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 ECL - CLK ECL - TTL DG +5V (D) FIGURE 21. STRAIGHT ECL INPUT 14 LATCH HI31466 Application Circuits (Continued) DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 DG 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 1 AG AG 2V +5V (A) +5V(D) 4V LATCH DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 PECL - CLK PECL - TTL DG +5V (D) FIGURE 22. STRAIGHT PECL INPUT DG +5V (D) DG 48 47 46 45 44 43 42 41 40 39 38 37 DG 8-BIT DIGITAL DATA 2 36 P1D0 TO P1D7 35 8-BIT DIGITAL DATA 3 34 4 33 +5V (A) 5 32 AG 6 31 7 30 8 29 9 28 AG 10 27 AG 11 26 AG AG 1 2V +5V (A) +5V(D) 4V DG +5V (D) DG 25 12 13 14 15 16 17 18 19 20 21 22 23 24 TTL - CLK DG +5V (D) FIGURE 23. STRAIGHT TTL INPUT 15 LATCH HI31466 Application Circuits (Continued) AG ANALOG INPUT AG + - +5V (A) + 1µF DG + 1µF AG 10µF 12 11 10 9 8 7 6 5 4 3 2 DGND3 VRT AGND VRM3 AVCC VRM2 VIN AVCC VRM1 AGND VRB 1 13 CLK/E RESETN/E 48 14 CLKN/E 15 CLK/T 16 NC SELECT 45 17 NC INV 44 18 NC CLKOUT 43 19 DVCC2 DVCC2 42 20 DGND2 DGND2 41 21 P2D0 P1D7 40 22 P2D1 P1D6 39 23 P2D2 P1D5 38 24 P2D3 P1D4 37 RESET/E 47 P2D6 (MSB) P2D7 P1D3 P2D5 32 33 34 35 36 P1D3 31 P1D2 DVCC2 30 P1D2 DVCC1 29 P1D1 DGND1 28 P1D1 P2D7 27 P1D0 P2D6 26 (LSB) P1D0 P2D5 25 DGND2 P2D4 RESETN/T 46 P2D4 P2D2 P2D3 AG 10µF SHORT TTL CLK (LSB) P2D0 P2D1 + SHORT SHORT THE ANALOG SYSTEM AND DIGITAL SYSTEM AT ONE POINT IMMEDIATELY UNDER THE A/D CONVERTER. SEE THE NOTES ON OPERATION IS THE CHIP CAPACITOR OF 0.1µF. FIGURE 24. STRAIGHT MODE TTL I/O (WHEN A SINGLE POWER SUPPLY IS USED) 16 P1D6 (MSB) P1D7 + 2V - - + P1D4 P1D5 (D) AG + +5V DVEE3 4V HI31466 Sales Office Headquarters ASIA Intersil (china) Ltd. china mainland TEL : (86) 13723742298 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. 17