INTERSIL 5962

5962-0721201QXC
®
Data Sheet
November 1, 2007
FN6558.1
Video Distribution Amplifier
Features
The 5962-0721201QXC is a fully DSCC SMD compliant
parts and the SMD data sheets is available on the DSCC
website (http://www.dscc.dla.mil/
programs/specfind/default.asp). The 5962-0721201QXC is
electrically equivalent to the EL8108. Reference equivalent
“EL8108” data sheet for additional information. The 59620721201QXC is a dual current feedback operational
amplifier designed for video distribution solutions. This
device features a high drive capability of 450mA while
consuming 13mA of supply current per amplifier and
operating from a single 5V to 12V supply.
• Drives up to 450mA from a +12V supply
The 5962-0721201QXC is available in the industry standard
10 Ld Flatpack. The 5962-0721201QXC is ideal for driving
multiple video loads while maintaining linearity.
• 20VP-P differential output drive into 100Ω
• -85dBc typical driver output distortion at full output at
150kHz
• -70dBc typical driver output distortion at 3.75MHz
• Low quiescent current of 13mA per amplifier
• 300MHz bandwidth
Applications
• Video distribution amplifiers
Pinout
5962-0721201QXC
(10 LD FLATPACK)
TOP VIEW
Ordering Information
PART NUMBER
PART MARKING
5962-0721201QXC 07212 01QHC
PACKAGE
PKG.
DWG. #
10 Ld Flat Pack K10.A
150Ω
150Ω
DIFF GAIN
DIFF PHASE
1
0
0.03
0.01
1
1
0.03
0.01
2
1
0.05
0.02
2
2
0.06
0.03
3
2
0.08
0.03
3
3
0.11
0.03
2
0
0.04
0.01
3
0
0.05
0.02
4
0
0.07
0.02
5
0
0.08
0.03
6
0
0.10
0.03
OUTA
NC
INA-
NC
INA+
VS+
GND
OUTB
INB+
INB-
2
3
TABLE 1.
1
1
4
5
10
9
8
7
6
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
5962-0721201QHC
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
VS+ Voltage to Ground . . . . . . . . . . . . . . . . . . . . . . -0.3V to +13.2V
VIN+ Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND to VS+
Current into any Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mA
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 60mA
Thermal Resistance (Typical)
θJA (°C/W)
10 Lead Flatpack . . . . . . . . . . . . . . . . . . . . . . . . . . .
177
Ambient Operating Temperature Range . . . . . . . . .-55°C to +125°C
Storage Temperature Range . . . . . . . . . . . . . . . . . .-60°C to +150°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
VS = 12V, RF = 750Ω, RL = 100Ω connected to mid supply, TA = +25°C, unless otherwise specified.
Electrical Specifications
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
HD
Total Harmonic Distortion, Differential
SR
Slew Rate, Single-ended
RF = 500Ω, AV = +2
200
MHz
RF = 500Ω, AV = +4
150
MHz
f = 200kHz, VO = 16VP-P, RL = 50Ω
-83
dBc
f = 4MHz, VO = 2VP-P, RL = 100Ω
-70
dBc
f = 8MHz, VO = 2VP-P, RL = 100Ω
-60
dBc
f = 16MHz, VO = 2VP-P, RL = 100Ω
-50
dBc
VOUT from -3V to +3V
800
V/µs
INPUT CHARACTERISTICS
eN
Input Noise Voltage
6
nV√ Hz
iN
-Input Noise Current
13
pA/√ Hz
450
mA
OUTPUT CHARACTERISTICS
IOUT
Output Current
RL = 0Ω
Typical Performance Curves
22
22
VS = ±6V, AV = 5
20 RL = 100Ω DIFF
18
RF = 243Ω
16
16
RF = 500Ω
GAIN (dB)
GAIN (dB)
VS = ±6V, AV = 5
20 RL = 100Ω DIFF
18
14
12
RF = 750Ω
10
RF = 1kΩ
14
12
8
6
6
4
4
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 1. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (FULL POWER MODE)
2
RF = 750Ω
10
8
2
100k
RF = 243Ω
RF = 500Ω
2
100k
RF = 1kΩ
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 2. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (3/4 POWER MODE)
FN6558.1
November 1, 2007
5962-0721201QHC
Typical Performance Curves
(Continued)
22
VS = ±6V, AV = 5
20 RL = 100Ω DIFF
18
28
VS = ±6V, AV = 10
26 RL = 100Ω DIFF
RF = 500Ω
24
22
RF = 243Ω
14
GAIN (dB)
GAIN (dB)
16
RF = 750Ω
12
10
RF = 1kΩ
8
10
10M
FREQUENCY (Hz)
100M
8
100k
500M
FIGURE 3. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (1/2 POWER MODE)
RF = 243Ω
RF = 500Ω
18
RF = 750Ω
20
12
10
10
100M
NORMALIZED GAIN (dB)
RF = 500Ω
8
6
4
RF = 1kΩ
2
0
RF = 750Ω
-2
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 6. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (1/2 POWER MODE)
8
RF = 248Ω
RF = 1kΩ
8
100k
500M
FIGURE 5. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (3/4 POWER MODE)
10
RF = 243Ω
16
14
RF = 1kΩ
VS = ±6V
14 A = 2
V
12 RL = 100Ω DIFF
RF = 750Ω
18
12
10M
FREQUENCY (Hz)
RF = 500Ω
22
GAIN (dB)
GAIN (dB)
20
14
GAIN (dB)
500M
VS = ±6V, AV = 10
26 RL = 100Ω DIFF
24
22
100k
100M
28
VS = ±6V, AV = 10
26 RL = 100Ω DIFF
24
1M
10M
FREQUENCY (Hz)
1M
FIGURE 4. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF (FULL POWER MODE)
28
8
100k
RF = 1kΩ
14
12
16
RF = 750Ω
16
4
1M
RF = 500Ω
18
6
2
100k
RF = 243Ω
20
6
VS = ±6V
AV = 2
RF = 500Ω
4
RL = 150Ω
2
0
-2
RL = 25Ω
-4
-6
RL = 50Ω
-8
1M
10M
100M
500M
FREQUENCY (Hz)
FIGURE 7. DIFFERENTIAL FREQUENCY RESPONSE WITH
VARIOUS RF
3
100k
1M
10M
100M
500M
FREQUENCY (Hz)
FIGURE 8. FREQUENCY RESPONSE FOR VARIOUS RLOAD
FN6558.1
November 1, 2007
5962-0721201QHC
Typical Performance Curves
(Continued)
-50
-50
VS = ±6V
AV = 5
-55
RL = 50Ω DIFF
RF = 750
-60
VS = ±6V
AV = 5
-55 R = 50Ω DIFF
L
RF = 750
-70
HD (dB)
HD (dB)
-60
-65
3rd HD
3rd HD
-70
-75
-75
-80
-85
-65
1
2
3
4
2nd HD
7
8
5
6
VOP-P (V)
2nd HD
-80
9
1
FIGURE 9. DISTORTION AT 2MHz
2
3
4
5
6
VOP-P (V)
7
8
9
8
9
FIGURE 10. DISTORTION AT 3MHz
-40
-40
VS = ±6V
A =5
-45 V
RL = 50Ω DIFF
RF = 750
-50
VS = ±6V
AV = 5
-45 RL = 50Ω DIFF
RF = 750
HD (dB)
HD (dB)
3rd HD
3rd HD
-55
-60
-50
-55
-65
2nd HD
-60
-70
-75
2nd HD
1
2
3
4
5
6
7
8
-65
9
1
2
3
4
VOP-P (V)
FIGURE 11. DISTORTION AT 5MHz
7
FIGURE 12. DISTORTION AT 10MHz
-60
-70
VS = ±6V
AV = 5
-75 R = 750
F
VOPP = 4V
VS = ±6V
AV = 5
-65 R = 750
F
VOPP = 4V
-80
-70
HD (dB)
HD (dB)
5
6
VOP-P (V)
2nd HD
-85
3rd HD
-75
-90
-80
-95
-85
3rd HD
2nd HD
-100
50
60
70
80
90 100 110
RLOAD (Ω)
120
130
140
150
FIGURE 13. 2nd AND 3rd HARMONIC DISTORTION vs RLOAD
@ 2MHz
4
-90
50
60
70
80
90 100 110
RLOAD (Ω)
120
130
140
150
FIGURE 14. 2nd AND 3rd HARMONIC DISTORTION vs RLOAD
@ 3MHz
FN6558.1
November 1, 2007
5962-0721201QHC
Typical Performance Curves
(Continued)
-40
-50
VS = ±6V
AV = 5
RF = 750
VOPP = 4V
-55
-60
-50
HD (dB)
HD (dB)
3rd HD
-70
-60
-65
-75
-80
-70
2nd HD
60
70
80
90 100 110
RLOAD (Ω)
120
130
140
-80
50
150
FIGURE 15. 2nd AND 3rd HARMONIC DISTORTION vs RLOAD
@ 5MHz
70
80
90 100 110
RLOAD (Ω)
120
130
140
150
24
VS = ±6V, AV = 5
22 RL = 50Ω
20 RF = 750Ω
18
GAIN (dB)
16
CL = 33pF
14
12
10
16
12
CL = 12pF
8
CL = 22pF
6
6
0
100k
4
100k
10M
FREQUENCY (Hz)
CL = 39pF
14
10
CL = 0pF
8
CL = 47pF
18
CL = 47pF
1M
60
FIGURE 16. 2nd AND 3rd HARMONIC DISTORTION vs RLOAD
@ 10MHz
VS = ±6V, AV = 5
22 R = 50Ω
L
20 RF = 750Ω
GAIN (dB)
2nd HD
-75
-85
100M
500M
FIGURE 17. FREQUENCY RESPONSE WITH VARIOUS CL
CL = 0pF
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 18. FREQUENCY RESPONSE vs VARIOUS CL
(3/4 POWER MODE)
-10
VS = ±6V, AV = 5
22 RL = 50Ω
20 RF = 750Ω
18
CL = 47pF
16
CL = 37pF
14
12
CL = 12pF
10
8
CL = 0pF
CHANNEL SEPARATION (dB)
24
GAIN (dB)
3rd HD
-55
-65
-90
50
VS = ±6V
AV = 5
RF = 750
VOPP = 4V
-45
-30
-50
A
-70
B
B
A
-90
6
4
100k
1M
10M
FREQUENCY (Hz)
100M
500M
FIGURE 19. FREQUENCY RESPONSE WITH VARIOUS CL
(1/2 POWER MODE)
5
-110
10k
100k
1M
FREQUENCY (Hz)
10M
100M
FIGURE 20. CHANNEL SEPARATION vs FREQUENCY
FN6558.1
November 1, 2007
5962-0721201QHC
Typical Performance Curves
(Continued)
10M
200
3M
-30
PHASE
MAGNITUDE (Ω)
PSRR (dB)
PSRR-
-50
150
300k
PSRR+
-70
100k
100
GAIN
50
30k
-90
PHASE (°)
-10
0
10k
-50
3k
-100
1k
-150
-200
-110
-110
100k
1M
10M
FREQUENCY (Hz)
1k
100M 200M
10M
1000
EN
10
1
0.1
IN0.01
0.001
100
1k
10k
100k
FREQUENCY (Hz)
1M
10
1
0.1
10k
10M
FIGURE 23. VOLTAGE AND CURRENT NOISE vs FREQUENCY
100k
1M
FREQUENCY (Hz)
100M
10M
FIGURE 24. OUTPUT IMPEDANCE vs FREQUENCY
150
0.40
VS = ±6V
AV = 5, RF = 750Ω,
RLOAD = 100Ω DIFF
0.35
DIFFERENTIAL GAIN (%)
120
110
BW (MHz)
100M
IN+
0.0001
10
FULL POWER MODE
100
90
10M
VS = ±6V, AV = 1
RF = 750Ω
100
130
100k
1M
FREQUENCY (Hz)
FIGURE 22. TRANSIMPEDANCE (ROL) vs FREQUENCY
OUTPUT IMPEDANCE (Ω)
VOLTAGE/CURRENT NOISE (nV/√Hz)(nA/√Hz)
FIGURE 21. PSRR vs FREQUENCY
10k
3/4 POWER MODE
80
70
1/2 POWER MODE
60
50
3.0
3.5
4.0
4.5
5.0
1/2 POWER MODE
0.25
0.20
0.15
0.10
3/4 POWER MODE
FULL POWER MODE
0.05
5.5
6.0
±VS (V)
FIGURE 25. DIFFERENTIAL BANDWIDTH vs SUPPLY VOLTAGE
6
0.30
0
1
2
3
4
# OF 150Ω LOADS
FIGURE 26. DIFFERENTIAL GAIN
FN6558.1
November 1, 2007
5962-0721201QHC
Typical Performance Curves
(Continued)
16
0.09
0.08
14
0.07
12
FULL POWER MODE
0.06
FULL POWER MODE
10
IS (mA)
DIFFERENTIAL PHASE (%)
VS = ±6V
0.05
3/4 POWER MODE
8
0.04
6
0.03
4
1/2 POWER MODE
3/4 POWER MODE
1/2 POWER MODE
0.02
2
0.01
0
1
2
3
+IS
-IS
1
4
3
2
# OF 150Ω LOADS
FIGURE 27. DIFFERENTIAL PHASE
1.8k
IB+
SLEW RATE (V/µs)
INPUT BIAS CURRENT (µA)
1.7k
0
-1
-2
IB-3
-4
1.6k
1.5k
1.4k
1.3k
0
25
50
75
100
125
1.2k
-50
150
-25
0
FIGURE 29. INPUT BIAS CURRENT vs TEMPERATURE
50
75
100
125
150
FIGURE 30. SLEW RATE vs TEMPERATURE
3.0
4
2.5
TRANSIMPEDANCE (MΩ)
5
3
2
1
2.0
1.5
1.0
0.5
0
-1
-50
25
TEMPERATURE (°C)
TEMPERATURE (°C)
OFFSET VOLTAGE (mV)
6
FIGURE 28. SUPPLY CURRENT vs SUPPLY VOLTAGE
1
-5
5
4
±VS (V)
-25
0
25
50
75
100
125
TEMPERATURE (°C)
FIGURE 31. OFFSET VOLTAGE vs TEMPERATURE
7
150
0
-50
-25
0
25
50
75
100
125
150
TEMPERATURE (°C)
FIGURE 32. TRANSIMPEDANCE vs TEMPERATURE
FN6558.1
November 1, 2007
5962-0721201QHC
(Continued)
5.10
16.0
RLOAD = 100Ω
5.05 VS = ±6V
15.5
SUPPLY CURRENT (mA)
OUTPUT VOLTAGE (±V)
Typical Performance Curves
5.00
4.95
4.90
4.85
4.80
4.75
-50
15.0
14.5
14.0
13.5
13.0
12.5
-25
0
25
50
75
TEMPERATURE (°C)
100
125
12.0
-50
150
FIGURE 33. OUTPUT VOLTAGE vs TEMPERATURE
3
-25
25
50
75
TEMPERATURE (°C)
0
100
125
150
FIGURE 34. SUPPLY CURRENT vs TEMPERATURE
AV = 5
RF = 750Ω
RL = 100Ω DIFF
PEAKING (dB)
2
1
0
-1
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VS (±V)
FIGURE 35. DIFFERENTIAL PEAKING vs SUPPLY VOLTAGE
Applications Information
Product Description
The 5962-0721201QXC is a dual current feedback
operational amplifier designed for video distribution solutions.
It is a dual current mode feedback amplifier with low distortion
while drawing moderately low supply current. It is built using
Intersil’s proprietary complimentary bipolar process. Due to
the current feedback architecture, the 5962-0721201QXC
closed-loop 3dB bandwidth is dependent on the value of the
feedback resistor. First the desired bandwidth is selected by
choosing the feedback resistor, RF, and then the gain is set by
picking the gain resistor, RG. The curves at the beginning of
the Typical Performance Curves section show the effect of
varying both RF and RG. The 3dB bandwidth is somewhat
dependent on the power supply voltage.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Ground
8
plane construction is highly recommended. Lead lengths
should be as short as possible, below ¼”. The power supply
pins must be well bypassed to reduce the risk of oscillation.
A 4.7µF tantalum capacitor in parallel with a 0.1µF ceramic
capacitor is adequate for each supply pin.
For good AC performance, parasitic capacitances should be
kept to a minimum, especially at the inverting input. This implies
keeping the ground plane away from this pin. Carbon resistors
are acceptable, while use of wire-wound resistors should not be
used because of their parasitic inductance. Similarly, capacitors
should be low inductance for best performance.
Capacitance at the Inverting Input
Due to the topology of the current feedback amplifier, stray
capacitance at the inverting input will affect the AC and
transient performance of the 5962-0721201QXC when
operating in the non-inverting configuration.
In the inverting gain mode, added capacitance at the inverting
input has little effect since this point is at a virtual ground and
stray capacitance is therefore not “seen” by the amplifier.
FN6558.1
November 1, 2007
5962-0721201QHC
Feedback Resistor Values
Single Supply Operation
The 5962-0721201QXC has been designed and specified
with RF = 500Ω for AV = +2. This value of feedback resistor
yields extremely flat frequency response with little to no
peaking out to 200MHz. As is the case with all current
feedback amplifiers, wider bandwidth, at the expense of
slight peaking, can be obtained by reducing the value of the
feedback resistor. Inversely, larger values of feedback
resistor will cause rolloff to occur at a lower frequency. See
the curves in the Typical Performance Curves section which
show 3dB bandwidth and peaking vs. frequency for various
feedback resistors and various supply voltages.
If a single supply is desired, values from +5V to +12V can be
used as long as the input common mode range is not
exceeded. When using a single supply, be sure to either 1)
DC bias the inputs at an appropriate common mode voltage
and AC couple the signal, or 2) ensure the driving signal is
within the common mode range of the 5962-0721201QXC.
Driving Cables and Capacitive Loads
The 5962-0721201QXC was designed with driving multiple
coaxial cables in mind. With 450mA of output drive and low
output impedance, driving six, 75Ω double terminated
coaxial cables to ±11V with one 5962-0721201QXC is
practical.
Bandwidth vs Temperature
Whereas many amplifier's supply current and consequently
3dB bandwidth drop off at high temperature, the 59620721201QXC was designed to have little supply current
variations with temperature. An immediate benefit from this
is that the 3dB bandwidth does not drop off drastically with
temperature.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back termination series resistor will
decouple the 5962-0721201QXC from the capacitive cable
and allow extensive capacitive drive.
Other applications may have high capacitive loads without
termination resistors. In these applications, an additional
small value (5Ω to 50Ω) resistor in series with the output will
eliminate most peaking.
Supply Voltage Range
The 5962-0721201QXC has been designed to operate with
supply voltages from ±2.5V to ±6V. Optimum bandwidth,
slew rate, and video characteristics are obtained at higher
supply voltages. However, at ±2.5V supplies, the 3dB
bandwidth at AV = +5 is a respectable 200MHz.
The schematic below shows the EL8108 driving 6 double
terminated cables, each of average length of 50 feet.
+5V
-5V
750
750
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
9
FN6558.1
November 1, 2007
5962-0721201QHC
Ceramic Metal Seal Flatpack Packages (Flatpack)
K10.A MIL-STD-1835 CDFP3-F10 (F-4A, CONFIGURATION B)
10 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
e
A
INCHES
A
-A-
D
-BPIN NO. 1
ID AREA
b
E1
0.004 M
H A-B S
Q
D S
S1
0.036 M
H A-B S
D S
C
E
-D-
A
-C-
-HL
E2
E3
SEATING AND
BASE PLANE
c1
L
E3
(c)
b1
M
M
(b)
SECTION A-A
MIN
MILLIMETERS
MAX
MIN
MAX
NOTES
A
0.045
0.115
1.14
2.92
-
b
0.015
0.022
0.38
0.56
-
b1
0.015
0.019
0.38
0.48
-
c
0.004
0.009
0.10
0.23
-
c1
0.004
0.006
0.10
0.15
-
D
-
0.290
-
7.37
3
E
0.240
0.260
6.10
6.60
-
E1
-
0.280
-
7.11
3
E2
0.125
-
3.18
-
-
E3
0.030
-
0.76
-
7
2
e
LEAD FINISH
BASE
METAL
SYMBOL
0.050 BSC
1.27 BSC
-
k
0.008
0.015
0.20
0.38
L
0.250
0.370
6.35
9.40
-
Q
0.026
0.045
0.66
1.14
8
S1
0.005
-
0.13
-
6
M
-
0.0015
-
0.04
-
N
10
10
Rev. 0 3/07
NOTES:
1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the limits of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass
overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric materials shall be molded to the bottom of the package to cover the
leads.
8. Dimension Q shall be measured at the point of exit (beyond the
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when solder dip lead finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
10
FN6558.1
November 1, 2007