DATASHEET Radiation Hardened Programmable Low Power Op Amps HS-3530ARH, HS-3530AEH Features The HS-3530ARH, HS-3530AEH are low power operational amplifiers, which are internally compensated monolithic devices offering a wide range of performance specifications. Parameters such as power dissipation, slew rate, bandwidth, noise and input DC parameters are programmed by selecting an external resistor or current source. Supply voltages as low as ±3V may be used with little degradation of AC performance. Operation from -55°C to +125°C is guaranteed. • Radiation performance - Single event latch-up . . . . . . . . . Immune (RSG DI Process) - High dose rate (50-300rad(Si)/s). . . . . . . . . . . 300krad(Si) - Low dose rate (0.01rad(SI)/s) . . . . . . . . . . . . . . 50krad(Si) A major advantage of the HS-3530ARH, HS-3530AEH is that operating characteristics remain virtually constant over a wide supply range (±3V to ±15V), allowing the amplifiers to offer maximum performance in almost any system, including battery operated equipment. A primary application for these devices is in active filtering and conditioning for a wide variety of signals that differ in frequency and amplitude. Also, by modulating the set current, they can be used for designs such as current controlled oscillators/modulators, sample and hold circuits and variable active filters. • Wide range AC programming - Slew rate . . . . . . . . . . . . . . . . . . . . . . . . . . 0.025 to 0.1V/µs - Gain X bandwidth. . . . . . . . . . . . . . . . . . . 30kHz to 750kHz • Wide range DC programming - Power supply range . . . . . . . . . . . . . . . . . . . . ±3.0V to ±15V • Supply current . . . . . . . . . . . . . . . . . . . . . . . . . 15µA to 150µA • Output current . . . . . . . . . . . . . . . . . . . . . . . 0.25mA to 2.5mA • Quiescent power. . . . . . . . . . . . . . . . . . . . . . . . . . 4.8mW (max) • Dielectrically isolated device islands • Short circuit protection • Full -55°C to +125°C military temperature range Specifications Specifications for Rad Hard QML devices are controlled by the Defense Logistics Agency Land and Maritime (DLA). The SMD numbers listed below must be used when ordering. Pin Configurations HS2-3530ARH, HS2-3530AEH (CAN), MACY1-X8 TOP VIEW ISET Detailed Electrical Specifications for the HS-3530ARH, HS-3530AEH are contained in SMD 5962-95687. A “hot-link” to the DLA website is also provided on the Product Information page for downloading the document. www.intersil.com/products/hs-3530arh The Intersil Quality Management Plan, listing all screening operations, is available on our website. www.intersil.com/design/quality/manuals.asp 8 OFFSET NULL INVERTING INPUT 1 7 2 NON-INVERTING INPUT 6 5 3 4 PART NUMBER TEMP. RANGE (°C) 5962F9568701QGA HS2-3530ARH-8 -55 to +125 5962F9568701VGA HS2-3530ARH-Q -55 to +125 5962F9568702VGA HS2-3530AEH-Q -55 to +125 5962F9568701VXC HS9-3530ARH-Q -55 to +125 5962F9568702VXC HS9-3530AEH-Q -55 to +125 5962F9568701V9A HS0-3530ARH-Q -55 to +125 5962F9568702V9A HS0-3530AEH-Q -55 to +125 HS2-3530ARH/PROTO HS2-3530ARH/Proto -55 to +125 HS9-3530ARH/PROTO HS9-3530ARH/Proto -55 to +125 HS0-3530ARH/SAMPLE HS0-3530ARH/SAMPLE February 9, 2015 FN4653.3 1 OUTPUT OFFSET NULL V- Ordering Information ORDERING NUMBER V+ HS9-3530ARH, HS9-3530AEH(FLATPACK), CDFP3-F10 TOP VIEW NC 1 10 ISET OFFSET 2 9 V+ - IN 3 8 OUTPUT + IN 4 7 OFFSET V- 5 6 NC -55 to +125 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 1999, 2012, 2013, 2015. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. HS-3530ARH, HS-3530AEH Die Characteristics ASSEMBLY RELATED INFORMATION SUBSTRATE POTENTIAL: DIE DIMENSIONS: Unbiased (DI) 1720µm x 1390µm x 533µm ±25.4µm (68 mils x 55 mils x 21 mils ±1 mil) ADDITIONAL INFORMATION INTERFACE MATERIALS WORST CASE CURRENT DENSITY: GLASSIVATION <2.0 x 105 A/cm2 Type: Silox (SiO2) Thickness: 8.0kA 1.0kA TRANSISTOR COUNT: 49 TOP METALLIZATION Type: AlSiCu Thickness: 16.0kA ±2kA SUBSTRATE: Radiation Hardened Silicon Gate, Dielectric Isolation BACKSIDE FINISH: Silicon Metallization Mask Layout Pin Numbers shown are for the Can Package HS-3530ARH, HS-3530AEH IN+ (3) IN(2) OFFSET (1) NC V- (4) NC ISET (8) NC OFFSET (5) OUTPUT (6) Submit Document Feedback 2 NC V+ (7) FN4653.3 February 9, 2015 HS-3530ARH, HS-3530AEH Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION February 9, 2015 FN4653.3 CHANGE Added Rev History and About Intersil Verbiage. Updated datasheet by removing sentence that was not in compliance. About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask. Reliability reports are also available from our website at www.intersil.com/support For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com Submit Document Feedback 3 FN4653.3 February 9, 2015