517CM

MECHANICAL CASE OUTLINE
PACKAGE DIMENSIONS
UDFN10 2.5x2, 0.5P
CASE 517CM
ISSUE O
DATE 14 AUG 2012
SCALE 4:1
PIN ONE
REFERENCE
2X
0.10 C
0.10 C
2X
0.05 C
L
A B
D
L
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSIONS b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 MM FROM TERMINAL TIP.
4. COPLANARITY APPLIES TO THE EXPOSED
PAD AS WELL AS THE TERMINALS.
L1
ÎÎ
ÎÎ
E
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
ÏÏ
ÎÎ
EXPOSED Cu
TOP VIEW
DETAIL B
A
(A3)
A3
MOLD CMPD
A1
ÎÎ
ÏÏ
DIM
A
A1
A3
b
D
E
e
L
L1
L2
DETAIL B
ALTERNATE
CONSTRUCTIONS
0.05 C
NOTE 4
A1
SIDE VIEW
C
SEATING
PLANE
GENERIC
MARKING DIAGRAM*
DETAIL A
1
5
10X
XXXM
G
L
L2
10
XXX = Specific Device Code
M = Date Code
G
= Pb−Free Package
6
e
10X
BOTTOM VIEW
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.13 REF
0.20
0.30
2.50 BSC
2.00 BSC
0.50 BSC
0.70
0.90
0.00
0.15
0.20 REF
b
0.10
M
C A B
0.05
M
C
NOTE 3
*This information is generic. Please refer to device data sheet for actual part marking.
Pb−Free indicator, “G” or microdot “ G”,
may or may not be present.
RECOMMENDED
MOUNTING FOOTPRINT
9X
10X
0.32
1.05
PACKAGE
OUTLINE
2.30
1
0.43
0.50 PITCH
DIMENSIONS: MILLIMETERS
DOCUMENT NUMBER:
98AON82885E
Electronic versions are uncontrolled except when
accessed directly from the Document Repository. Printed
STATUS: ON SEMICONDUCTOR STANDARD
versions are uncontrolled except when stamped
“CONTROLLED COPY” in red.
NEW STANDARD:
© Semiconductor Components Industries, LLC, 2002
Case Outline Number:
http://onsemi.com
UDFN10 2.5X2, 0.5P
DESCRIPTION:
October, 2002
− Rev. 0
PAGE 1 OFXXX
2
1
DOCUMENT NUMBER:
98AON82885E
PAGE 2 OF 2
ISSUE
O
REVISION
RELEASED FOR PRODUCTION. REQ. BY J. LETTERMAN.
DATE
14 AUG 2012
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
© Semiconductor Components Industries, LLC, 2012
August, 2012 − Rev. O
Case Outline Number:
517CM