HS-2210M-05-0300 HS-2210M-05-0300 Unipolar 2 - Wire Hall Effect Sensor M10 thread Product image serves as example only. Block Diagram Features › Compact size › Various switching sensivity › Customized types aviable Approvals Product image serves as example only. Absolute Maximum Ratings Stresses beyond those listed in the “Absolute Maximum Ratings“ may cause permanent damage to the device Functional operation of the device at these conditions is not implied. Exposure to the absolute rating conditions for extended periods will affect device reliability Symbol Parameter VSUP Supply voltage wire colour Min. red Max. Unit - 18 Conditions V t < 1000 h 1) - 28 V t < 96 h 1) - 32 V t < 5 min 1) - 40 V t < 5 x 400 ms 1) with series resistor RV > 100 Ohm VOUT Output voltage V t < 1000 h 1) - 28 V t < 96 h 1) - 32 V t < 5 min 1) - 40 V t < 5 x 400 ms 1) red - 65 mA red - 50 red - 0.5 with series resistor RV > 100 Ohm Output current IO IOR Reverse output current 1) No cumulative stress mA All voltages listed are referenced to ground (GND) Dimensions Wire Assignment Name Function Cable colour VSUP Supply voltage red GND Ground black HS-2210M-05-0300 wire length [mm] Material Information Material Environmental Characteristics Operating temperature Page 1 of 3 Rev. 1.1, 12.02.2016, (006, 009, 008) hs2210m_05_0300_ds_e_1.1 °C - 20 to + 85 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Colour Housing Nickel plated brass nickel Cable UL1007/1569, AWG 24 red, black Potting compound Epoxy black Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com HS-2210M-05-0300 HS-2210M-05-0300 Unipolar 2 - Wire Hall Effect Sensor M10 thread Characteristics At recommended operation conditions if not otherwise specified in the column "Conditions". Typical characteristics for TJ = 25 °C and VSUP = 12 V Symbol Parameter wire colour Min. red red red 2 12 Typ. Max. Unit Conditions Supply ISUPIo ISUPIo ISUPhi Low supply current High supply current Reverse current 5 17 1 mA mA mA 1 1 µs µs µs µs µs for VSUP = - 18 V Output tf tf td tsamp ten Output fall time1) Output rise time Delay time 1) Output refresh period Enable time of output after settling of VSUP 16 2 50 1.6 2.66 1) VSUP = 12 V; VSUP = 12 V B > Bon + 2 mT or B < Boff - 2 mT Power-on-self-test Self test can be triggered externally; details on request 1) Guaranteed by design Recommended Operating Conditions Symbol Parameter VSUP Supply voltage wire colour red Min. Max. Unit 3.0 24 V Conditions Magnetic Characteristics Overview Symbol Parameter wire colour BONth ON threshold range BOOth OFF threshold range Bth Adjustable step size 2) - TC Temperatur compensation of - 1) 1) Min. Typ. Max. Unit - - 30 30 mT - - 30 30 mT 0.5 0 Conditions mT - 3000 ppm/K magnetic thresholds 3) 1) Avaible range 2) Small steps at small values, bigger steps at higher values. May not be undercut 3) Different temperature compensation avaible on request Page 2 of 3 Rev. 1.1, 12.02.2016, (006, 009, 008) hs2210m_05_0300_ds_e_1.1 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com HS-2210M-05-0300 HS-2210M-05-0300 Unipolar 2 - Wire Hall Effect Sensor M10 thread Magnetic Characteristics Switching Type latching 1) Temp. koeff. of magnetic thresh. On point BON Off point BOFF TC [ppm/K] Min. [mT] Typ. Max. Min. [mT] Typ. Max. 0 tbd. 6.0 tbd. tbd. 4.0 tbd. A B C D E F Hysteresis BHYS 1) Min. [mT] Typ. Max. - 2.0 - The hysteresis is the difference between the switching points BHYS = BON - BOFF Magnetic Approach (for example) Page 3 of 3 Rev. 1.1, 12.02.2016, (006, 009, 008) hs2210m_05_0300_ds_e_1.1 PIC Proximity Instrumentation Controls Kontaktbauelemente GmbH Nibelungenstr. 5A 90530 Wendelstein, Germany Phone +49 911 99 59 06-0 Fax +49 911 99 59 06-99 [email protected] pic-gmbh.com