Toggles Series JS02 & JS04 Rockers General Specifications Electrical Capacity (Resistive Load) Pushbuttons 25mA @ 24V DC 0.1A @ 50V DC Keylocks Programmable Illuminated PB Other Ratings JS02 Extended Actuator JS04 Flush Actuator 50 milliohms maximum 100 megohms minimum @ 100V DC 300V AC minimum for 1 minute minimum 2,000 operations minimum 2,000 operations minimum .026” (0.65mm) Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Total Travel: 50 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 2,000 operations minimum 2,000 operations minimum .031” (0.8mm) Materials & Finishes JS02 Extended Actuator JS04 Flush Actuator Actuator: Glass fiber reinforced polyamide Glass fiber reinforced polyamide Cover: Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Base: Glass fiber reinforced polyamide (UL94V-0) Glass fiber reinforced polyamide (UL94V-0) Contacts: Beryllium copper with gold plating Copper alloy with gold plating Terminals: Brass with gold plating Brass with gold plating Rotaries Slides Switching Rating: Nonswitching Rating: H Environmental Data Operating Temp Range: JS02 Extended Actuator: –20°C through +70°C (–4°F through +158°F) JS04 Flush Actuator: –30°C through +85°C (–22°F through +185°F) Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Tactiles Ultra-Miniature SMT DIP Slides Soldering: Cleaning: Reflow Soldering Recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: Switches are packaged in OFF position and should be soldered in OFF position. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL 94V-0 rated cover & base The JS Series slides have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current circuit. When used as intended in a low-voltage, low-current circuit, the results do not produce hazardous energy. Supplement Accessories Indicators Touch PCB Processing H24 www.nkk.com Toggles Series JS02 & JS04 Ultra-Miniature SMT DIP Slides Rockers Distinctive Characteristics Pushbuttons Extended and flush slide actuators available. Programmable Illuminated PB Twin sliding contact mechanism with self-cleaning action (JS02) provides smooth actuation and produces high contact reliability. Gold plated contacts prevent oxidation and sulfide effect and provide stable contact resistance. Keylocks Use of self-extinguishing UL94V-0 certified material in cover and base provides high arc resistance and high insulation resistance. Terminal spacing conforms to standard PCB grid. For JS02: .100” (2.54mm) For JS04: .050” (1.27mm) H Tactiles End-to-end stackable. Slides Rotaries Gull-wing terminals ensure secure PCB mounting and prevent dislodging during vapor phase and infrared convection reflow soldering. Tilt Packaged in tape-reel or stick-tube. Tape-reel packaging meets EIA-481-D Standard. Indicators Touch Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Accessories Actual Sizes JS02 www.nkk.com Supplement JS04 H25 Toggles Series JS02 & JS04 Ultra-Miniature SMT DIP Slides Rockers TYPICAL SWITCH ORDERING EXAMPLE 02 08 A P4 S Programmable Illuminated PB Pushbuttons JS Mounting SMT .100” (2.54mm) for Extended Actuator 04 SMT .050” (1.27mm) for Flush Actuator A Extended for 02 Mounting Code F Flush for 04 Mounting Code Packaging S Stick-Tube R Tape-Reel Not available in bulk No. Of Positions H 04 4 Positions 08 8 Positions Contact Material & Rating P4 Gold Rated 25mA @ 24V DC Tactiles Slides Rotaries Keylocks 02 Actuator Tilt DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch JS0208AP4-S Indicators Extended Slide Actuator, 8 Positions SPST OFF-ON Circuit Accessories .100” (2.54mm) Terminal Spacing Gold Contacts with 25mA Rating Supplement Stick-Tube Packaging H26 www.nkk.com Toggles Series JS02 & JS04 Ultra-Miniature SMT DIP Slides TYPICAL SWITCH DIMENSIONS Single Pole 4 Positions • Extended Actuator 3 4 (0.8) Travel .031 (11.1) .437 (0.3) .012 (2.54) Typ .100 (0.25) .010 5 (7.62) .300 (1.1) Typ .043 1 2 3 4 5 6 7 8 8 (8.9) .350 1 (0.7) .028 (0.5) Typ .020 7 (9.8) .386 (1.0) .039 (0.6) .024 (3.7) .146 6 (1.5) Typ .059 Pushbuttons 2 2 (0.8) .031 3 4 (1.1) Typ .043 (7.62) .300 Programmable Illuminated PB 1 (1.8) .071 Rockers ON (6.2) .244 (2.54) Typ .100 (7.62) .300 End View Schematic Single Pole JS0204AP4 8 Positions • Extended Actuator ON (6.2) .244 3 4 6 5 7 8 (0.8) Travel .031 (21.26) .837 (0.3) .012 (2.54) Typ .100 (0.25) .010 9 (7.62) .300 (1.1) Typ .043 (0.7) .028 (0.5) Typ .020 (1.0) .039 (0.6) .024 (2.54) Typ .100 (17.78) .700 11 12 13 14 15 1 16 2 2 3 (0.8) .031 4 5 6 7 8 (17.78) .700 (1.26) .050 5 6 7 8 Schematic Single Pole (0.7) Typ .028 4 9 10 11 12 13 14 15 16 (1.1) Typ .043 End View JS0208AP4 4 Positions • Flush Actuator H ON 5 6 7 8 (5.8) .228 (6.22) .245 (7.65) .301 (8.1) .319 (1.27) Typ .050 (0.1) .004 (0.5) Typ .020 (3.81) .150 (0.6) .024 4 5 6 7 8 (3.81) .150 Schematic JS0404FP4 8 Positions • Flush Actuator (1.25) Typ .049 (1.27) Typ .050 (0.35) .014 9 10 11 12 13 14 15 16 (5.8) .228 (11.3) .445 (2.2) .087 (0.1) .004 (0.5) Typ .020 (1.27) Typ .050 (8.89) .350 (0.15) .006 (7.65) .301 (8.1) .319 (0.6) .024 1 2 3 4 5 6 7 8 Accessories (0.65) Travel .026 Indicators ON 1 2 3 4 5 6 7 8 (0.65) .026 3 Single Pole .028 (1.26) .050 (0.76) Typ .030 End View (0.7) Typ 2 1 2 3 4 (2.2) .087 (0.15) .006 1 Tactiles (0.65) .026 (1.25) Typ .049 (1.27) Typ .050 (0.35) .014 Tilt (0.65) Travel .026 1 2 3 4 5 6 7 8 (0.76) Typ .030 9 10 11 12 13 14 15 16 (8.89) .350 End View Schematic www.nkk.com Touch 1 2 3 4 Supplement 3 (8.9) .350 (9.8) .386 1 (3.7) .146 10 (1.5) Typ .059 Keylocks 2 Rotaries 1 (1.8) .071 Slides JS0408FP4 H27 Toggles Series JS02 & JS04 PACKAGING Rockers S Stick-Tube Packaging Pushbuttons Switches are packaged in OFF position. Switches are not available in bulk and must be ordered in the following increments: Programmable Illuminated PB Extended Actuator JS0204AP4-S: 46 pieces per stick-tube JS0208AP4-S: 24 pieces per stick-tube (7.0) .276 (530.0) 20.866 (12.0) .472 Keylocks Flush Actuator JS0404FP4-S: 80 pieces per stick-tube JS0408FP4-S: 45 pieces per stick-tube (4.8) .189 (530.0) 20.866 Rotaries (11.5) .453 R Tape-Reel Packaging for Extended Actuator (1.75) .069 (2.0) Typ .079 3° 1 2 (24.0) .945 Tilt 4 (6.5) .256 (10.3) .406 (2.0) Typ .079 (1.75) .069 Touch (0.35) .014 Direction of Feed (5.0) .197 Tape Dimensions for JS0204AP4-R Tape-reel packaging meets EIA-481-D Standard. (6.5) R .256 (11.5) .453 3 (2.5) .098 (1.5) Dia Typ .059 JS0204AP4-R: 500 pieces per tape-reel JS0208AP4-R: 500 pieces per tape-reel (1.5) Dia Typ .059 (4.0) Typ .157 (11.5) .453 Minimum Leader Length: 15.75” (400mm) Minimum Trailer Length: 6.3” (160mm) (16.0) Typ .630 (1.5) Dia Typ .059 (4.0) Typ .157 3° 2 3 (10.5) Typ .413 ON (14.25) Typ .561 1 (80.0) Dia 3.150 (80.0) Dia 3.150 5 6 (6.0) .236 7 (32.0) 1.260 8 (2.0) Typ .079 (21.7) .854 4 (2.0) Dia Typ .079 Accessories Indicators (16.0) Typ .630 ON Switches are packaged in OFF position. Switches are not available in bulk and must be ordered in the following increments: H Tactiles Slides Ultra-Miniature SMT DIP Slides Supplement Overall Dia (330.0) 13.0 Reel Dimensions H28 (24.4) .961 (30.4) Max 1.197 (32.4) 1.276 JS0204AP4-R (38.4) Max 1.512 JS0208AP4-R www.nkk.com (6.0) .236 (10.3) .406 Direction of Feed (1.7) Typ .067 (0.35) .014 (1.5) Typ .059 Tape Dimensions for JS0208AP4-R (5.0) .197 Toggles Series JS02 & JS04 PACKAGING (CONTINUED) (4.0) Typ .157 (11.5) .453 (1.5) Dia Typ .059 5° (24.0) .945 1 2 3 4 Minimum Leader Length: 15.75” (400mm) Minimum Trailer Length: 6.3” (160mm) (12.0) Typ .472 (2.3) .091 (1.5) Dia Typ .059 (4.0) .157 (8.7) .343 Tape-reel packaging meets EIA-481-D Standard. (6.6) .260 ON JS0404FP4-R: 2,000 pieces per tape-reel JS0408FP4-R: 2,000 pieces per tape-reel (2.0) Typ .079 Rockers Switches are packaged in OFF position. Switches are not available in bulk and must be ordered in the following increments: (1.75) .069 Pushbuttons Tape-Reel Packaging for Flush Actuator Programmable Illuminated PB R (0.3) .012 Direction of Feed (2.7) 1.06 Tape Dimensions for JS0404FP4-R 5° (24.0) .945 (2.3) .091 (1.5) Dia Typ .059 (2.0) Typ .079 Overall Dia (330.0) 13.0 (11.5) .453 1 2 3 4 5 6 7 8 (80.0) Dia 3.150 (24.4) .961 (4.0) .157 (8.7) .343 (30.4) Max 1.197 (1.5) Dia Typ .059 Direction of Feed ON (10.5) Typ .413 (4.0) Typ .157 Keylocks (6.5) R .256 (12.0) Typ .472 (11.7) .461 Rotaries (1.75) .069 (2.0) Typ .079 (0.3) .012 (2.7) 1.06 H Tape Dimensions for JS0408FP4-R Supplement Accessories Indicators Touch Tilt Tactiles Reel Dimensions for JS0404FP4-R & JS0408FP4-R Slides Ultra-Miniature SMT DIP Slides www.nkk.com H29