Download Catalog

Slides
Toggles
Contents
Rockers
AS Series......................................... H4
Programmable Illuminated PB
Pushbuttons
0.4VA Logic Level
Straight, Right Angle & Vertical PC
CS Series...................................... H10
Keylocks
3A Power Level
Straight PC
PCB Mount
FS Series....................................... H14
H
JS01, JS03 Series............................ H18
Tactiles
Slides
Rotaries
High Frequency
90MHz to 1GHz
Straight PC
Tilt
Extended & Piano Actuated DIP Slides
25mA @ 24V DC
Straight PC
Touch
JS02, JS04 SMT Series..................... H24
Supplement
Accessories
Indicators
Ultra-miniature 25mA DIP Slide
Gull Wing Terminals
4- & 8-position
H2
www.nkk.com
Contents
Toggles
Slides
Rockers
MS Series...................................... H30
Pushbuttons
6A Power Level & 0.4VA Logic Level
Solder Lug, Straight PC, Right Angle & Vertical PC
Panel Mount, PCB Mount, & Bracket Mount
Programmable Illuminated PB
MS Illuminated Series....................... H38
Keylocks
6A Power Level
LED Illumination
Solder Lug & Straight PC
PCB Mount & Flat Frame Mount
SM Series...................................... H42
SS Series....................................... H44
SS Illuminated Series........................ H49
Supplement
Ultra-miniature 0.4VA Logic Level
Side Actuated
Accessories
SS3 SMT Series.............................. H53
Indicators
Touch
0.1A Power Level
LED Illumination
Top & Side Actuation
PCB Mount
Tilt
Tactiles
0.1A Power Level & 0.4VA Logic Level
Top & Side Actuated
PCB Mount
H
Slides
Rotaries
Ultra-miniature
500mA or 1.0mA
Straight PC
www.nkk.com
H3
Toggles
Series AS
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Logic Level:
Programmable Illuminated PB
Other Ratings
Keylocks
Materials & Finishes
Rotaries
Slides
Tactiles
Tilt
Touch
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Travel: H
Actuator:
Upper Case Housing:
Lower Case Housing:
Support Bracket:
Movable Contact:
Stationary Contacts:
Terminals:
Environmental Data
Operating Temperature Range:
Humidity: Vibration:
Shock:
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
50 milliohms maximum
500 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
50,000 operations minimum
50,000 operations minimum
2.55N
Nonshorting (break-before-make)
Pretravel: .082” (2.1mm); Overtravel: .016” (0.4mm); Total Travel: .098” (2.5mm)
Glass fiber reinforced polyamide
Carbon blended polyacetal (antistatic)
Glass fiber reinforced polyamide
Tin plated phosphor bronze
Phosphor bronze with gold plating
Brass with gold plating
Brass with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 192 hours @ 40°C (104°F)
10 ~ 60Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 5 minutes; 3 right angled directions for 30 minutes
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
PCB Processing
Soldering: Wave Soldering Recommended. See Profile A in Supplement section.
Manual Soldering: for single pole see Profile B in Supplement section; for double pole see Profile A.
Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
The A Series slides have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Supplement
Accessories
Indicators
Subminiature Slides
H4
www.nkk.com
Toggles
Series AS
Subminiature Slides
Rockers
Distinctive Characteristics
Pushbuttons
Subminiature size (1/3 size of Series M switches) saves space on PC boards.
Programmable Illuminated PB
Specifically developed for logic-level applications.
Keylocks
Award-winning STC contact mechanism with benefits
unavailable in conventional mechanisms: smoother,
positive detent actuation, increased contact
stability and unparalleled logic-level reliability.
(Additional STC details in Terms & Acronyms;
see Supplement section.)
Available in various actuator lengths.
H
Tactiles
Molded-in, epoxy sealed or ultrasonically
welded terminals lock out flux, solvents,
and other contaminants.
Slides
Rotaries
Antistatic superstructure of carbon
blended polyacetal prevents static
discharge to the contacts.
Tilt
.100” x .100” (2.54mm x 2.54mm) terminal
spacing conforms to standard PC board grid
spacing.
Touch
Matching indicators available.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
H5
Series AS
Toggles
Subminiature Slides
TYPICAL SWITCH ORDERING EXAMPLE
Pushbuttons
Rockers
AS
2
Programmable Illuminated PB
Poles
1
SPST
SPDT
2
DPDT
SP3T
2
A
H
Actuators
Circuits
PC Terminals
1
ON
NONE
OFF
A
.098” (2.5mm) Long
2
ON
NONE
ON
B
Flush
*B
Straight with Bracket
.150” (3.8mm) Long
*H
Right Angle with Bracket
*V
Vertical with Bracket
3
ON
OFF
ON
4
ON
ON
ON
C
P
Straight
* Bracketed models are
ESD protected
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Keylocks
AS22AH
DPDT
ON-NONE-ON Circuit
Rotaries
.098” (2.5mm) Long
Actuator
Right Angle PC Terminals
H
Slide Position
Touch
Connected Terminals
Throw & Schematics
Left
Center
Right
Left
Center
Right
Note: Terminal numbers are not
actually on the switch.
Pole
Model
SP
AS11
ON
NONE
OFF
3-1
OPEN
OPEN
SPST
SP
AS12
AS13
ON
ON
NONE
OFF
ON
ON
2-1
2-1
OPEN
OPEN
2-3
2-3
SPDT
AS22
AS23
ON
ON
NONE
OFF
ON
ON
2-1 5-4
2-1 5-4
OPEN
OPEN
2-3 5-6
2-3 5-6
DPDT
Tilt
Tactiles
Slides
POLES & CIRCUITS
DP
1
3
INTERNAL
CONNECTION
2 (COM)
1
3
(COM)
2
1
3
5
6
4
Connected Terminals & Schematics
Pole
SP
Supplement
Accessories
Indicators
For 3 Throw (3-On)
Model
AS24
Left
Center
Right
ON
ON
ON
External
Connection
2 (in)
5
1 (out)
3 4 (out) 6 (out)
2-1 5-4
H6
External Connection
External
Connection
2 (in)
5
1 (out)
3 4 (out) 6 (out)
2-3 5-4
www.nkk.com
External
Connection
2 (in)
5
1 (out)
3 4 (out) 6 (out)
2-3 5-6
The SP3T model utilizes
a double pole base.
External
connections
must be
made
during field
installation.
(out)
(out)
Common
(in)
1
4
2
5
3
6
External
Conn
(out)
Series AS
Toggles
Subminiature Slides
ACTUATORS
(2.4)
.094
(3.8)
.150
(2.4)
.094
(2.4)
.094
Pushbuttons
(2.4)
.094
(2.4)
.094
(2.4)
.094
.150” (3.8mm) Long
C
Rockers
Flush
B
Actuator Color: Gray standard; contact factory for other colors.
B
Straight
Straight
with Bracket
(10.16)
.400
(5.08)
.200
(5.08)
.200
(0.3) Typ
.012
(2.54) Typ
.100
(5.08) Typ
.200
H
(0.6) Dia Typ
.024
Right Angle
with Bracket
(2.54) Typ
.100
(0.6) Dia Typ
.024
(0.7) Typ
.028
(9.0)
.354
(8.8)
.346
Vertical
with Bracket
(5.08)
.200
(2.54) Typ
.100 (0.6) Dia Typ
.024
(2.54) Typ
.100
(2.54) Typ
.100
(5.08)
.200
(0.3)
.012
(5.08)
.200 (0.3)
.012 (0.7)
.028
(0.5)
.020
(0.8)
.031
(9.0)
.354
V
(8.8)
.346
(8.8)
.346
(0.6) Dia Typ
.024
(0.5) Typ
.020
(0.7)
.028
(9.0)
.354
(9.0)
.354
Keylocks
P
Programmable Illuminated PB
PC TERMINALS
(8.8)
.346
Use of a support bracket is recommended to increase PCB mounting strength and stability.
Single Pole
P/N This Side
(0.6) Dia Typ
.024
(9.8)
.386
2
3
(0.3)
.012
(2.5) Travel
.098
(2.5)
.098
(5.38)
.212
(0.8)
.031
(9.1)
.358
(2.54) Typ
.100
3
CL
H
(2.54) Typ
.100
(0.8) Dia Typ
.031
CL
Actuator shown in LEFT position
Single throw models do not have terminal 2.
Double Pole
(0.4) Typ
.016
(2.4) Sq
.094
(0.4)
.016
(2.06)
.081
P/N This Side
(2.5) Travel
.098
(9.2)
.362
(2.5)
.098
(0.8)
.031
(9.1)
.358
Straight PC
(0.6) Dia Typ
.024
1
4
2
5
3
6
(2.54) Typ
.100
(3.1)
.122
(9.8)
.386
4
1
5
2
6
3
(5.08)
.200
(2.54) Typ
.100
(0.8) Dia Typ
.031
(5.08)
.200
AS22AP
Actuator shown in LEFT position
Single Pole
(2.4) Sq
.094
(2.06)
.081
P/N This Side
(5.7)
.224
(0.3)
.012
(2.5) Travel
.098
(2.5)
.098
(0.8)
.031
(9.1)
.358
Straight PC • Bracket
(0.3) Typ
.012
(0.6) Dia Typ
.024
(10.16)
.400
(3.1)
.122
(1.0)
.039
(0.7) Typ
.028
1
1
(9.8)
.386
2
3
(2.54) Typ
.100
Actuator shown in LEFT position
AS12AP
Tilt
2
(1.0)
.039
(3.1)
.122
(1.0)
.039
1
1
Tactiles
(2.06)
.081
Touch
(0.4) Typ
.016
CL
(1.0)
.039
(2.54)
.100
www.nkk.com
Accessories
(2.4) Sq
.094
Straight PC
(2.54) Typ
.100
2
3
CL
(0.8) Dia Typ
.031
(2.54)
.100
Supplement
Rotaries
TYPICAL SWITCH DIMENSIONS
Slides
(2.5)
.098
Indicators
.098” (2.5mm) Long
A
AS12AB
H7
Series AS
Toggles
Subminiature Slides
TYPICAL SWITCH DIMENSIONS
Straight PC • Bracket
Double Pole
Rockers
P/N This Side
(2.06)
.081
(2.4) Sq
.094
(0.3) Typ
.012
(0.6) Dia Typ
.024
Pushbuttons
(10.16)
.400
(0.4)
.016
Programmable Illuminated PB
Keylocks
5
3
6
P/N This Side
(2.4) Sq
.094
(9.8)
.386
(9.9)
.389
(2.5)
.098
(3.1)
.122
(0.8)
.031
(2.5) Travel
.098
(2.06)
.081
(0.3) Typ
.012
(5.08)
.200
P/N This Side
2
(0.7)
.028
(2.5)
.098
(9.8)
.386
3
(2.54) Typ
.100
(0.8) Dia Typ
.031
(6.18)
.243
1
2
3
(2.54) Typ
.100
(5.08)
.200
(0.8) Dia Typ
.031
(0.6) Dia Typ
.024
(2.54) Typ
.100
(0.8)
.031
(12.4)
.489
(2.54)
.100
(5.08)
.200
3
2
1
6
5
4
(3.1)
.122
(0.5)
.020
(10.0)
.394
1
2
(2.54) Typ
.100
(2.54)
3
.100
4
5
6
(5.08)
.200
(0.8) Dia Typ
.031
(0.6) Dia Typ
.024
(2.54) Typ
.100
Single Pole
(0.4)
.016
(2.06)
.081
(0.8)
.031
P/N This Side
Tilt
1
(5.3)
.208
(2.5) Travel
.098
(0.3) Typ
.012
(2.54)
.100
Touch
6
Actuator shown in LEFT position
(2.4) Sq
.094
(0.7) Typ
.028
(2.54)
.100
(2.54)
.100
(5.7)
.224
(2.5)
.098
(15.0)
.589
(10.2)
.402
2
3
(1.0)
.039
(2.54) Typ
.100
1
2
3
(0.5)
.020
(1.0)
(3.1)
.039
.122
(2.54) Typ
.100
(0.6) Dia Typ
.024
(1.0)
.039
(0.8) Dia Typ
.031
(2.54)
.100
CL
CL
Actuator shown in LEFT position
AS12AV
Indicators
1
(3.1)
.122
(5.08)
.200
(5.2)
.205
Vertical PC
Vertical PC
Double Pole
(0.4)
.016
(2.4) Sq
.094
Accessories
2
Double Pole
(2.4) Sq
.094
AS22AH
(0.3) Typ
.012
(5.08)
.200
Supplement
1
5
(3.3)
.131
Actuator shown in LEFT position
(0.4)
.016
H8
4
(0.7) Typ
.028
(5.08)
.200
3
(0.7)
.028
AS12AH
AS22AV
(9.8)
.386
Single Pole
(2.5) Travel
.098
(2.06)
.081
(0.3) Typ
.012
(5.08)
.200
Rotaries
Slides
4
2
(2.54) Typ
.100
(0.3)
.012
H
1
Actuator shown in LEFT position
AS22AB
Right Angle PC
(0.8)
.031
(9.1)
.358
(2.5)
.098
(9.5)
.374
Right Angle PC
Tactiles
(2.5) Travel
.098
(5.08)
.200
(9.5)
.374
(2.06)
.081
P/N This Side
(2.5) Travel
.098
(0.7)
.028
(5.08)
.200
(2.5)
.098
(0.8)
.031
(5.3)
.208
(15.0)
.589
(1.0) (0.5) (3.1)
.039 .020 .122
(2.54) Typ
.100
Actuator shown in LEFT position
www.nkk.com
1
4
2
5
3
6
(10.2)
.402
4
1
5
2
6
3
(5.08)
.200
(2.54) Typ
.100
(5.08)
.200
(0.6) Dia Typ
.024
(5.08)
.200
(0.8) Dia Typ
.031
Toggles
Series CS
Miniature Power Rated Slides
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Power Level:
Programmable Illuminated PB
Other Ratings
10 milliohms maximum
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
50,000 operations minimum
20,000 operations minimum
Withstands 12 kilovolts ESD
Nonshorting (break-before-make)
.087” (2.2mm)
Keylocks
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Static Capability:
Contact Timing:
Total Travel: 3A @ 125V AC or 2A @ 250V AC
Materials & Finishes
Slides
Rotaries
Actuator:
Cover & Case:
Movable Contacts:
Stationary Contacts:
Terminals:
H
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Tactiles
Glass fiber reinforced polyamide
Glass fiber reinforced polyamide (UL94V-0)
Copper with silver plating
Silver capped copper with silver plating
Copper with silver plating
Soldering Time & Temp: Cleaning:
Standards & Certifications
Flammability Standard:
Wave Soldering: See Profile A in Supplement section.
Manual Soldering: See Profile B in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL94V-0 cover & case
Supplement
Accessories
Indicators
Touch
Installation
H10
www.nkk.com
Toggles
Series CS
Miniature Power Rated Slides
Rockers
Distinctive Characteristics
Programmable Illuminated PB
Pushbuttons
High performance and high quality at a low price.
Molded cover and case of high insulating material
withstand 12 kilovolts of electrostatic discharge
(ESD), providing antistatic feature.
Epoxy sealed terminals to lock out flux,
dust, and other contaminants.
H
Touch
Tilt
Tactiles
Suited for a wide variety of applications
including telecommunications, electronic
controls, audio devices, and household
appliances.
Slides
Rotaries
Keylocks
Cover and case UL 94V-0 flammability
rated.
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
H11
Series CS
Toggles
Miniature Power Rated Slides
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
1
2
A
N
W
03
Pushbuttons
CS
Actuators
Programmable Illuminated PB
Poles
1
SPDT
A
Narrow for Single Pole
2
DPDT
B
Wide for Double Pole
Circuits
ON
W
Silver Rated
3A @ 125V AC
Mounting
NONE
N
ON
Terminals
03
PCB Mount
Straight PC
Keylocks
2
Contact Material
& Rating
CS12ANW03
H
Narrow Actuator
Silver Contacts
with 3-Amp Rating
Tactiles
Slides
Rotaries
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
SPDT
ON-NONE-ON Circuit
Tilt
Straight PC Terminals
for PCB Mounting
POLES & CIRCUITS
Connected Terminals
Throw & Schematics
Left
Center
Right
Left
Center
Right
Note: Terminal numbers are
not actually on switch.
Pole
Model
SP
CS12
ON
NONE
ON
2-1
OPEN
2-3
SPDT
DP
CS22
ON
NONE
ON
2-1 5-4
OPEN
2-3 5-6
DPDT
2 (COM)
1
2
Supplement
Accessories
Indicators
Touch
Slide Position
H12
www.nkk.com
1
3
(COM)
3
4
5
6
Series CS
Toggles
Miniature Power Rated Slides
MOUNTING
Panel Cutouts
Rockers
PCB Footprints
(4.8)
.189
1
(9.0)
.354
(4.6)
.181
Single Pole
(4.7) Typ
.185
5
1
(1.6) Dia Typ
.063
Double Pole
6
2
(4.7) Typ
.185
4
(1.6) Dia Typ
.063
Single Pole
Double Pole
Programmable Illuminated PB
2
TYPICAL SWITCH DIMENSIONS
Single Pole
ON
(4.7) Typ
.185
(5.1)
.201
(6.4)
.252
1
(4.3)
.169
(6.4)
.252
(6.6)
.260
(1.2)
.047
Actuator shown in LEFT position
CS12ANW03
Double Pole
(0.7) Typ
.028
(0.5)
.020
(5.1)
.201
(7.6)
.299
(4.3)
.169
(6.4)
.252
(0.5)
.020
6
3
5
2
4
1
H
(12.7)
.500
(4.8)
.189
(11.4)
.449
CS22BNW03
Accessories
Indicators
Touch
Tilt
Actuator shown in LEFT position
Supplement
(8.2)
.323
(11.8)
.465
(4.7) Typ
.185
ON
(3.8)
.150
(1.2) Typ
.047
Tactiles
ON
(14.0)
.551
Keylocks
(12.7)
.500
2
(3.8)
.150
(3.8)
.150
(7.0)
.276
3
Rotaries
ON
(14.0)
.551
(0.5)
.020
(0.7) Typ
.028
(0.5)
.020
Slides
(6.8)
.268
(6.8)
.268
3
Pushbuttons
3
www.nkk.com
H13
Toggles
Series FS
Rockers
General Specifications
Pushbuttons
For high frequency (DC through 1GHz): Isolation 40dB minimum at 1GHz.
Insertion loss 0.5dB maximum at 1GHz.
Impedance 75 ohms
Programmable Illuminated PB
Highly reliable, self-cleaning twin contact mechanism with gold plating
Long total travel of .138” (3.5mm) for highly visible actuator position
Distinct audible and tactile feedback during actuation
Keylocks
Suited to high frequency applications (90MHz to 1GHz) such as CATV and
communication equipment
Slides
Rotaries
Distinctive Characteristics
Electrical Capacity (Resistive Load)
H
Logic Level:
Tactiles
Impedance:
Insertion Loss:
Isolation:
Indicators
Touch
Tilt
Other Ratings
Accessories
Actual Size
with Tall Actuator
Innovative alternative to relay products
RF Ratings
Supplement
Miniature Slides for High Frequency
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
Installation
Soldering Time & Temp: Cleaning:
H14
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
75 ohms
0.5dB maximum @ 1GHz
40dB minimum @ 1GHz
200 milliohms maximum
250 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
1,000 operations minimum
1,000 operations minimum
Nonshorting (break-before-make)
.138” (3.5mm)
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 5 minutes; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering: See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
www.nkk.com
Series FS
Toggles
Miniature Slides for High Frequency
2
2
A
A
P
Pole
A
DPDT
Terminals
P
DC through 1GHz
Circuit
ON
Actuators
NONE
ON
A
Short (.291” or 7.4mm)
B
Tall (.488” or 12.4mm)
Rotaries
2
Straight PC
Keylocks
2
Frequency Band
Programmable Illuminated PB
Pushbuttons
FS
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
H
Tactiles
FS22AAP
Slides
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Short Actuator
DPDT
ON-NONE-ON Circuit
Tilt
Frequency Band DC through 1GHz
Touch
Straight PC Terminals
Model
DP
FS22
Left
Center
Right
Left
Center
Right
ON
NONE
ON
2-1 5-4
NA
2-3 5-6
www.nkk.com
Throw & Schematics
Note: Terminal numbers are not
actually on the switch.
DPDT
2
1
(COM)
3
4
5
6
H15
Accessories
Pole
Connected Terminals
Supplement
Slide Position
Indicators
POLE & CIRCUIT
Series FS
Toggles
Miniature Slides for High Frequency
HIGH FREQUENCY PERFORMANCE
RF Connection Options
5
2
6
3
Out
In
4
1
5
2
6
3
Out
In
Keylocks
1
5
2
6
3
Out
In
Out 2
A
T = Terminator
A = Amplifier or other device
Isolation
Insertion Loss
>40dB @ 1GHz
(higher value is better)
<0.5dB @ 1GHz
(lower value is better)
Standing Wave Ration
or Impedance Matching
Isolation: Greater than 40dB @ 1GHz
80
H
4
A
= Circuit Trace
90
Option 3
Direction of Actuation
1
T
Rotaries
Slides
4
0.6
Standing Wave = ratio between highest
voltage & lowest voltage
(must always be more than 1)
Insertion Loss: Less than 0.5dB @ 1GHz
1.6
0.5
70
0.4
dB 60
dB 0.3
50
0.2
40
0.1
30
10MHz
500MHz
1GHz
0
VSWR (Voltage Standing Wave Ratio):
1:1 @ 1GHz
1.5
1.4
V
S 1.3
W
R
1.2
1.1
10MHz
500MHz
1
1GHz
10MHz
500MHz
1GHz
Note: The data above reflects the conditions using the FS switch on a test PCB with two coaxial connectors.
High frequency applications require external connection on the PCB. Contact factory for details.
Tilt
Tactiles
Option 2
Direction of Actuation
Programmable Illuminated PB
Pushbuttons
Direction of Actuation
Rockers
Option 1
TYPICAL SWITCH DIMENSIONS
Touch
Short & Tall Actuators
Indicators
(3.5) Travel
.138
(7.4)
.291
(3.5) Typ
.138
Accessories
(17.0)
.669
(15.7)
.618
Part
No.
(3.5) Travel
.138
(1.75) Typ
.069
(3.0) Sq
.118
Supplement
(7.4)
.291
FS22ABP
H16
(12.4)
.488
(0.3)
.012
(9.6)
.378
4
4
1
5
5
2
(0.8) Dia Typ 6
.031
(1.2) Dia Typ
.047
(1.6) Dia Typ
.063
3
6
3
(0.6) Typ
.024
(0.3) Typ
.012
(2.9)
.114
Actuator in LEFT position.
www.nkk.com
1
2
(4.0)
.157
(2.0) Typ
.079
(1.75) Typ
.069
(3.5) Typ
.138
(7.85) Typ
.309
Toggles
Series JS01 & JS03
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Programmable Illuminated PB
Pushbuttons
Other Ratings
Keylocks
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Total Travel: Materials & Finishes
Actuator:
Cover:
Base:
Contacts:
Terminals:
Rotaries
Slides
Switching Rating:
Nonswitching Rating:
H
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
25mA @ 24V DC
0.1A @ 50V DC
50 milliohms maximum
100 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
2,000 operations minimum
2,000 operations minimum
For slide actuator: .031” (0.8mm); for piano actuator: .114” (2.9mm)
JS01 Slide DIP
Glass fiber reinforced polyamide
Glass fiber reinforced polyamide (UL94V-0)
Glass fiber reinforced polyamide (UL94V-0)
Beryllium copper with gold plating
Brass with gold plating
JS03 Piano DIP
Glass fiber reinforced PBT
Glass fiber reinforced PBT (UL94V-0)
Glass fiber reinforced PBT (UL94V-0)
Phosphor bronze with gold plating
Phosphor bronze with gold plating
–25°C through +70°C (–13°F through +158°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Tactiles
Ultra-Miniature Slide & Piano DIP
Indicators
Touch
PCB Processing
Soldering: Cleaning:
Standards & Certifications
Flammability Standards: UL 94V-0 rated cover & base
The JS series devices have not been tested for UL recognition and CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended in a low-voltage, low-current circuit, the results do not produce
hazardous energy.
Supplement
Accessories
Wave Soldering Recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Note: Switches are packaged in OFF position and should be soldered in OFF position.
These devices are not process sealed. Hand clean locally using alcohol based solution.
H18
www.nkk.com
Toggles
Series JS01 & JS03
Ultra-Miniature Slide & Piano DIP
Rockers
Distinctive Characteristics
Pushbuttons
Slide type and piano type actuators available.
Programmable Illuminated PB
Twin sliding contact mechanism with self-cleaning action (JS01)
provides smooth actuation and produces high contact reliability.
Keylocks
Gold plated contacts prevent oxidation and sulfide effect
and provide stable contact resistance.
Slanted terminals ensure secure PCB mounting and
prevent dislodging during wave soldering.
H
Tactiles
Terminal spacing conforms to standard .100” (2.54mm) PCB grid.
Slides
Rotaries
Use of self-extinguishing UL94V-0 certified material
in cover and base provides high arc resistance and
high insulation resistance.
Touch
Tilt
End-to-end stackable.
Indicators
Actual Sizes
Accessories
JS01
Supplement
JS03
www.nkk.com
H19
Toggles
Series JS01 & JS03
Ultra-Miniature Slide & Piano DIP
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
01
08
A
P4
S
Mounting
Actuator
01
Through-hole
for Slide Actuator
A
Extended Slide for
01 Mounting Code
Packaging
03
Through-hole
for Piano Actuator
P
Piano for
03 Mounting Code
S
Rotaries
H
04
4 Positions
08
8 Positions
Contact Material
& Rating
P4
JS slides are SPST devices
with OFF-ON circuit
Gold Rated
25mA @ 24V DC
Tactiles
Slides
No. Of Positions
Tilt
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Touch
JS0108AP4-S
Extended Slide Actuator
Indicators
SPST OFF-ON Circuit with 8 Positions
Accessories
Gold Contacts with 25mA Rating
Through-hole Mounting
for Slide Actuator
Supplement
Stick-Tube Packaging
H20
www.nkk.com
Stick-Tube
Not available in bulk
Keylocks
Programmable Illuminated PB
Pushbuttons
JS
Toggles
Series JS01 & JS03
Ultra-Miniature Slide & Piano DIP
TYPICAL SWITCH DIMENSIONS
Slide Actuator
4 Positions
ON
4
(2.54) Typ
.100
5
6
7
8
(9.0)
.354
(1.1) Typ
.043
(3.5)
.138
(0.3)
.012
(0.5) Typ
.020
2
3
4
5
6
7
8
(7.62)
.300
(1.0)
.039
(0.6)
.024
(3.5)
.138
1
Pushbuttons
(0.8) Travel
.031
1
2
3
4
(7.62)
.300
(0.8) Dia Typ
.031
Programmable Illuminated PB
(11.1)
.437
(2.54) Typ
.100
(7.62)
.300
Schematic
End View
JS0104AP4
Slide Actuator
8 Positions
ON
(6.2)
.244
(21.26)
.837
8
(0.8) Travel
.031
9
(1.0)
.039
(0.6)
.024
(3.5)
.138
(0.5) Typ
.020
(2.54) Typ
.100
10
11
12
13
14
15
(17.78)
.700
1
16
(9.0)
.354
(1.1) Typ
.043
(3.5)
.138
(0.3)
.012
2
3
4
2
3
4
5
6
7
7
8
9 10 11 12 13 14 15 16
8
(17.78)
.700
(0.8) Dia Typ
.031
(2.54) Typ
.100
Schematic
End View
Piano Actuator
(1.4) Typ
.055
5
6
7
(8.8)
.346
1
2
3
(3.7)
.146
(0.2) Typ
.008
(7.62)
.300
(11.34)
.446
(7.62)
.300
(10.6)
.417
4
(1.0) Dia Typ
.039
1
2
3
4
5
6
7
8
Schematic
Piano Actuator
(9.2)
.362
1 2 3 4 5 6 7 8
ON
9
10
11
12
13
14
15
(8.8)
.346
(2.9)
.114
16
1
2
3
4
5
6
7
8
(17.78)
.700
(0.2) Typ
.008
(7.62)
.300
(10.6)
.417
8 Positions
(7.62)
.300
(3.7)
.146
(0.6) Typ
.024
(2.54) Typ
.100
JS0304PP4
(2.54) Typ
.100
(12.15)
.478
(1.4) Typ
.055
(17.78)
.700
(21.5)
.846
1
2
3
(1.0) Dia Typ
.039
4
5
6
7
8
9 10 11 12 13 14 15 16
Schematic
www.nkk.com
H
8
(7.62)
.300
4 Positions
(7.62)
.300
(2.9)
.114
(0.6) Typ
.024
(2.54) Typ
.100
JS0108AP4
(2.54) Typ
.100
(12.15)
.478
1 2 3 4
ON
6
(7.62)
.300
1
(9.2)
.362
5
Keylocks
7
Rotaries
6
Tactiles
5
Tilt
4
Indicators
3
Accessories
2
Supplement
1
(1.8)
.071
Slides
3
Touch
2
1
(1.8)
.071
Rockers
(6.2)
.244
JS0308PP4
H21
Series JS01 & JS03
Toggles
Ultra-Miniature Slide & Piano DIP
PACKAGING
Rockers
S
Stick-Tube Packaging
Switches are not available in bulk and must be
ordered in increments of:
Pushbuttons
Slide Actuator
JS0104AP4-S: 46 pieces per stick-tube
JS0108AP4-S: 24 pieces per stick-tube
Programmable Illuminated PB
Piano Actuator
JS0304PP4-S: 44 pieces per stick-tube
JS0308PP4-S: 23 pieces per stick-tube
Keylocks
Switches are packaged in OFF position.
Rotaries
Stick-Tube Dimensions for Slide Actuator
JS0104AP4-S & JS0108AP4-S
(16.0)
.630
(11.0)
.433
(12.0)
.472
(530.0)
20.866
(14.0)
.551
H
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Slides
Stick-Tube Dimensions for Piano Actuator
JS0304PP4-S & JS0308PP4-S
H22
www.nkk.com
(530.0)
20.866
Toggles
Series JS02 & JS04
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
25mA @ 24V DC
0.1A @ 50V DC
Keylocks
Programmable Illuminated PB
Other Ratings
JS02 Extended Actuator
JS04 Flush Actuator
50 milliohms maximum
100 megohms minimum @ 100V DC
300V AC minimum for 1 minute minimum
2,000 operations minimum
2,000 operations minimum
.026” (0.65mm)
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Total Travel: 50 milliohms maximum 100 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
2,000 operations minimum 2,000 operations minimum
.031” (0.8mm)
Materials & Finishes
JS02 Extended Actuator
JS04 Flush Actuator
Actuator: Glass fiber reinforced polyamide
Glass fiber reinforced polyamide Cover: Glass fiber reinforced polyamide (UL94V-0)
Glass fiber reinforced polyamide (UL94V-0)
Base: Glass fiber reinforced polyamide (UL94V-0)
Glass fiber reinforced polyamide (UL94V-0)
Contacts: Beryllium copper with gold plating
Copper alloy with gold plating
Terminals: Brass with gold plating
Brass with gold plating
Rotaries
Slides
Switching Rating:
Nonswitching Rating:
H
Environmental Data
Operating Temp Range: JS02 Extended Actuator: –20°C through +70°C (–4°F through +158°F)
JS04 Flush Actuator:
–30°C through +85°C (–22°F through +185°F)
Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F)
Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Tactiles
Ultra-Miniature SMT DIP Slides
Soldering: Cleaning:
Reflow Soldering Recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Note: Switches are packaged in OFF position and should be soldered in OFF position.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL 94V-0 rated cover & base
The JS Series slides have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended in a low-voltage, low-current circuit, the results do not produce hazardous
energy.
Supplement
Accessories
Indicators
Touch
PCB Processing
H24
www.nkk.com
Toggles
Series JS02 & JS04
Ultra-Miniature SMT DIP Slides
Rockers
Distinctive Characteristics
Pushbuttons
Extended and flush slide actuators available.
Programmable Illuminated PB
Twin sliding contact mechanism with self-cleaning action (JS02)
provides smooth actuation and produces high contact reliability.
Gold plated contacts prevent oxidation and sulfide effect
and provide stable contact resistance.
Keylocks
Use of self-extinguishing UL94V-0 certified material
in cover and base provides high arc resistance and
high insulation resistance.
Terminal spacing conforms to standard PCB grid.
For JS02: .100” (2.54mm)
For JS04: .050” (1.27mm)
H
Tactiles
End-to-end stackable.
Slides
Rotaries
Gull-wing terminals ensure secure PCB mounting
and prevent dislodging during vapor phase and
infrared convection reflow soldering.
Tilt
Packaged in tape-reel or stick-tube. Tape-reel packaging meets
EIA-481-D Standard.
Indicators
Touch
Coplanarity: all considered surfaces must lie between two parallel planes
that are a maximum distance apart of .0059” (0.15mm). (Additional
coplanarity details in Terms and Acronyms in the Supplement section.)
Accessories
Actual Sizes
JS02
www.nkk.com
Supplement
JS04
H25
Toggles
Series JS02 & JS04
Ultra-Miniature SMT DIP Slides
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
02
08
A
P4
S
Programmable Illuminated PB
Pushbuttons
JS
Mounting
SMT .100” (2.54mm)
for Extended Actuator
04
SMT .050” (1.27mm)
for Flush Actuator
A
Extended for 02
Mounting Code
F
Flush for 04
Mounting Code
Packaging
S
Stick-Tube
R
Tape-Reel
Not available in bulk
No. Of Positions
H
04
4 Positions
08
8 Positions
Contact Material
& Rating
P4
Gold Rated
25mA @ 24V DC
Tactiles
Slides
Rotaries
Keylocks
02
Actuator
Tilt
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Touch
JS0208AP4-S
Indicators
Extended Slide Actuator, 8 Positions
SPST OFF-ON Circuit
Accessories
.100” (2.54mm) Terminal Spacing
Gold Contacts with 25mA Rating
Supplement
Stick-Tube Packaging
H26
www.nkk.com
Toggles
Series JS02 & JS04
Ultra-Miniature SMT DIP Slides
TYPICAL SWITCH DIMENSIONS
Single Pole
4 Positions • Extended Actuator
3
4
(0.8) Travel
.031
(11.1)
.437
(0.3)
.012
(0.25)
.010
(2.54) Typ
.100
5
(7.62)
.300
(1.1) Typ
.043
1
2
3
4
5
6
7
8
8
(8.9)
.350
1
(0.7)
.028 (0.5) Typ
.020
7
(9.8)
.386
(1.0)
.039
(0.6)
.024
(3.7)
.146
6
(1.5) Typ
.059
Pushbuttons
2
2
(0.8)
.031
3
4
(1.1) Typ
.043
(7.62)
.300
Programmable Illuminated PB
1
(1.8)
.071
Rockers
ON
(6.2)
.244
(2.54) Typ
.100
(7.62)
.300
End View
Schematic
Single Pole
JS0204AP4
8 Positions • Extended Actuator
ON
(6.2)
.244
3
4
6
5
7
8
(0.8) Travel
.031
(21.26)
.837
(0.3)
.012
(2.54) Typ
.100
(0.25)
.010
9
(7.62)
.300
(1.1) Typ
.043
(0.7)
.028
(0.5) Typ
.020
(1.0)
.039
(0.6)
.024
(2.54) Typ
.100
(17.78)
.700
11
12
13
14
15
1
16
2
2
3
(0.8)
.031
4
5
6
7
8
(17.78)
.700
(1.26)
.050
5
6
7
8
Schematic
Single Pole
(0.7) Typ
.028
4
9 10 11 12 13 14 15 16
(1.1) Typ
.043
End View
JS0208AP4
4 Positions • Flush Actuator
H
ON
5 6 7 8
(5.8)
.228
(6.22)
.245
(7.65)
.301
(8.1)
.319
(0.15)
.006
(0.1)
.004
(0.5) Typ
.020
(3.81)
.150
(0.6)
.024
3
4
5
6
7
8
(3.81)
.150
Schematic
Single Pole
.028
JS0404FP4
8 Positions • Flush Actuator
(5.8)
.228
(11.3)
.445
(2.2)
.087
(0.1)
.004
(0.5) Typ
.020
(1.27) Typ
.050
(8.89)
.350
(1.25) Typ
.049
(1.27) Typ
.050
(0.35)
.014
9 10 11 12 13 14 15 16
(8.1)
.319
(7.65)
.301
1
2
3
4
5
6
7
8
Accessories
(0.65) Travel
.026
Indicators
ON
1 2 3 4 5 6 7 8
(0.65)
.026
(0.76) Typ
.030
End View
(0.7) Typ
(1.26)
.050
2
1 2 3 4
(2.2)
.087
(1.27) Typ
.050
1
Tactiles
(0.65)
.026
(1.25) Typ
.049
(1.27) Typ
.050
(0.35)
.014
Tilt
(0.65) Travel
.026
1 2 3 4 5 6 7 8
(0.15)
.006
(0.6)
.024
(0.76) Typ
.030
9 10 11 12 13 14 15 16
(8.89)
.350
Schematic
End View
www.nkk.com
Touch
1 2 3 4
Supplement
3
(8.9)
.350
(9.8)
.386
1
(3.7)
.146
10
(1.5) Typ
.059
Keylocks
2
Rotaries
1
(1.8)
.071
Slides
JS0408FP4
H27
Toggles
Series JS02 & JS04
PACKAGING
Rockers
S
Stick-Tube Packaging
Pushbuttons
Switches are packaged in OFF position.
Switches are not available in bulk and must
be ordered in the following increments:
Programmable Illuminated PB
Extended Actuator
JS0204AP4-S: 46 pieces per stick-tube
JS0208AP4-S: 24 pieces per stick-tube
(7.0)
.276
(530.0)
20.866
(12.0)
.472
Keylocks
Flush Actuator
JS0404FP4-S: 80 pieces per stick-tube
JS0408FP4-S: 45 pieces per stick-tube
(4.8)
.189
(530.0)
20.866
Rotaries
(11.5)
.453
R
Tape-Reel Packaging for Extended Actuator
(1.75)
.069
(2.0) Typ
.079
(11.5)
.453
3°
1
2
(24.0)
.945
(2.0) Typ
.079
Tilt
(1.75)
.069
Touch
(0.35)
.014
Direction of Feed
(5.0)
.197
Tape Dimensions for JS0204AP4-R
Tape-reel packaging meets EIA-481-D Standard.
(6.5) R
.256
(16.0) Typ
.630
(1.5) Dia Typ
.059
(4.0) Typ
.157
3°
2
3
(10.5) Typ
.413
ON
(14.25) Typ
.561
1
(80.0) Dia
3.150
(80.0) Dia
3.150
5
6
(6.0)
.236
7
(32.0)
1.260
8
(2.0) Typ
.079
(21.7)
.854
4
(2.0) Dia Typ
.079
Accessories
Indicators
4
(6.5)
.256
(10.3)
.406
Minimum Leader Length: 15.75” (400mm)
Minimum Trailer Length: 6.3” (160mm)
(11.5)
.453
3
(2.5)
.098
(1.5) Dia Typ
.059
JS0204AP4-R: 500 pieces per tape-reel
JS0208AP4-R: 500 pieces per tape-reel
(1.5) Dia Typ
.059
(4.0) Typ
.157
(16.0) Typ
.630
ON
Switches are packaged in OFF position.
Switches are not available in bulk and must
be ordered in the following increments:
H
Tactiles
Slides
Ultra-Miniature SMT DIP Slides
Supplement
Overall Dia (330.0)
13.0
Reel Dimensions
H28
(24.4)
.961
(30.4) Max
1.197
(32.4)
1.276
JS0204AP4-R
(38.4) Max
1.512
JS0208AP4-R
www.nkk.com
(6.0)
.236
(10.3)
.406
Direction of Feed
(1.7) Typ
.067
(0.35)
.014
(1.5) Typ
.059
Tape Dimensions for JS0208AP4-R
(5.0)
.197
Toggles
Series JS02 & JS04
PACKAGING (CONTINUED)
(4.0) Typ
.157
(11.5)
.453
(1.5) Dia Typ
.059
5°
(24.0)
.945
1 2 3 4
Minimum Leader Length: 15.75” (400mm)
Minimum Trailer Length:
6.3” (160mm)
(12.0) Typ
.472
(2.3)
.091
(1.5) Dia Typ
.059
(4.0)
.157
(8.7)
.343
Tape-reel packaging meets EIA-481-D Standard.
(6.6)
.260
ON
JS0404FP4-R: 2,000 pieces per tape-reel
JS0408FP4-R: 2,000 pieces per tape-reel
(2.0) Typ
.079
Rockers
Switches are packaged in OFF position.
Switches are not available in bulk and must
be ordered in the following increments:
(1.75)
.069
Pushbuttons
Tape-Reel Packaging for Flush Actuator
Programmable Illuminated PB
R
(0.3)
.012
Direction of Feed
(2.7)
1.06
Tape Dimensions for JS0404FP4-R
5°
(24.0)
.945
(2.3)
.091
(1.5) Dia Typ
.059
(2.0) Typ
.079
Overall Dia (330.0)
13.0
(11.5)
.453
1 2 3 4 5 6 7 8
(80.0) Dia
3.150
(24.4)
.961
(4.0)
.157
(8.7)
.343
(30.4) Max
1.197
(1.5) Dia Typ
.059
Direction of Feed
ON
(10.5) Typ
.413
(4.0) Typ
.157
Keylocks
(6.5) R
.256
(12.0) Typ
.472
(11.7)
.461
Rotaries
(1.75)
.069
(2.0) Typ
.079
(0.3)
.012
(2.7)
1.06
H
Tape Dimensions for JS0408FP4-R
Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Reel Dimensions for JS0404FP4-R & JS0408FP4-R
Slides
Ultra-Miniature SMT DIP Slides
www.nkk.com
H29
Toggles
Series MS
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Programmable Illuminated PB
Pushbuttons
Power Level (silver): 6A @ 125V AC or 3A @ 250V AC
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level: Combines silver & gold ratings
(gold over silver)
Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings
Keylocks
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: Tilt
Tactiles
Slides
Rotaries
Materials & Finishes
H
Actuator:
Frame:
Dust Cover:
Case:
Movable Contacts:
Stationary Contacts:
Terminals:
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
Indicators
Touch
Processing
Soldering: Cleaning:
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
100,000 operations minimum
25,000 operations minimum for silver; 50,000 operations minimum for gold
Nonshorting (break-before-make)
On-None-On circuit .087” (2.2mm); all other circuits .138” (3.5mm)
Glass fiber reinforced PBT resin (UL94V-0)
Stainless steel for panel & PCB mount; phosphor bronze with tin plating for bracket mount
Phosphor bronze with nickel plating
Glass fiber reinforced diallyl phthalate resin (UL94V-0)
Silver alloy (code W); copper with gold plating (code G);
or silver alloy with gold plating (code A)
Silver capped copper with silver plating (code W); copper with gold plating (code G);
or silver alloy with gold plating (code A)
Copper or brass with silver or gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering recommended (PC Mount). See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V-0 rated actuator & case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” or “/CUL” to end of part number to order UL recognized switch.
All Single & Double Pole Double Throw models recognized at 6A @ 125V AC & 3A @ 250V AC.
CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” to end of part number to order CSA certified switch.
All Double Throw & 3 Throw models certified at 6A @ 125V AC, 3A @ 250V AC, &
0.4VA maximum @ 28V DC.
Supplement
Accessories
Miniature Slides
H30
www.nkk.com
Toggles
Series MS
Miniature Slides
Rockers
Distinctive Characteristics
Pushbuttons
Available in flat frame and bracketed PC mounting types.
Programmable Illuminated PB
Over-center actuator block and plunger design gives crisp
actuation with clear indication of circuit status; this design
also diminishes sparking and increases operating life.
Guide interlocked with actuator block prevents
window locking and maintains correct plunger
alignment to assure contact stability.
Keylocks
Antijamming design protects contacts from
damage due to excessive downward force
on the actuator.
Specially composed silver alloy contacts for
power applications or gold contacts for logic
level applications give high contact reliability.
Tactiles
H
Slides
Rotaries
High internal barriers between poles and
insulating sheet between case and actuator
block give added protection to contacts.
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Actual Size
Supplement
Accessories
Indicators
Clinching of frame to case well above base and terminals provides
1,500V dielectric strength.
Touch
Tilt
Epoxy sealed terminals prevent entry of flux, solvents,
and other contaminants.
www.nkk.com
H31
Series MS
Toggles
Miniature Slides
TYPICAL SWITCH ORDERING EXAMPLE
Pushbuttons
Rockers
MS
2
A
S
Programmable Illuminated PB
1
SPDT
2
DPDT
SP3T
Actuators
Keylocks
NONE
ON
ON
OFF
ON
0
ON
ON
ON
Rotaries
ON
3
H
30
A
.150” (3.8mm) Wide for
Single or Double Pole
W
Silver; Rated 6A @ 125V
AC & 3A @ 250V AC
B
.323” (8.2mm) Wide for
Double Pole
G
Gold; Rated 0.4VA max. @
28V AC/DC max.
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA
max. @ 28V AC/DC max.
Circuits
2
G
Contact Materials
& Ratings
Poles
Mounting
F
Panel Mount
(Terminal 01 only)
N
PCB Mount
(Terminal 03 only)
01
Solder Lug
03
Straight PC
S
Bracket Mount
(Terminals 13, 30, &
40 only)
13
Straight with Bracket
30
Right Angle PC
40
Vertical PC
Terminals
IMPORTANT:
Switches are supplied without UL, cULus & CSA marking unless specified.
UL, cULus & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the General
Specifications page.
Touch
Tilt
Tactiles
Slides
1
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Indicators
MS12ASG30
Gold Contacts with 0.4VA Rating
Accessories
.150” (3.8mm) Wide
Actuator
Right Angle PC Terminals
with Support Bracket
Supplement
SPDT
ON-NONE-ON Circuit
H32
www.nkk.com
Series MS
Toggles
Miniature Slides
POLES & CIRCUITS
DP
Right
MS12
ON
NONE
ON
MS13
ON
OFF
ON
MS22
ON
NONE
ON
MS23
ON
OFF
ON
Left
Center
Right
2-1
OPEN
2-3
Note:
Model
Terminal numbers are
not actually on the switch.
2 (COM)
SPDT
1
2-1 5-4
OPEN
2-3 5-6
Rockers
Center
2
DPDT
1
Pushbuttons
SP
Left
Throw & Schematics
3
(COM)
3
5
Programmable Illuminated PB
Pole
Connected Terminals
6
4
For 3 Throw (3-On)
Connected Terminals & Schematics
MS20
Left
Center
Right
ON
ON
ON
External
Connection
2 (in)
5
3 4 (out) 6 (out)
1 (out)
External
Connection
2 (in)
5
1 (out)
2-1 5-4
External Connection
The SP3T model utilizes a
double pole base.
External
Connection
2 (in)
5
3 4 (out) 6 (out)
1 (out)
2-3 5-4
(out)
3 4 (out) 6 (out)
2-3 5-6
Keylocks
SP
Model
External
connections
must be made
during field
installation.
External
Conn
6
3
5
2
4
1
(out)
Common
(in)
Rotaries
Pole
(out)
ACTUATORS
.150” (3.8mm) Wide
for Single Pole
(3.8)
.150
(3.8)
.150
B
.323” (8.2mm) Wide
for Double Pole Only
(3.8)
.150
(3.8)
.150
(8.2)
.323
Tilt
(3.8)
.150
.150” (3.8mm) Wide
for Double Pole
Tactiles
A
H
Slides
Slide Position
Silver over Silver
Power Level
6A @ 125V AC & 3A @ 250V AC
G
Gold over Brass or Copper
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Indicators
W
Touch
CONTACT MATERIALS & RATINGS
Gold over Silver
Power Level
or Logic Level
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits
within the same application. See Supplement section for complete explanation of dual rating and operating range.
www.nkk.com
Supplement
A
Accessories
Note: Complete explanation of operating range in Supplement section.
H33
Series MS
Toggles
Miniature Slides
MOUNTING TYPES & TERMINALS
Rockers
F
Pushbuttons
(4.19)
.165
Programmable Illuminated PB
Straight PC Mount
(Combines with
Straight PC Terminal
03 only)
(9.0)
.354
SP or DP with .150”
(3.8mm) Actuator
Maximum Panel Thickness: .197” (5.0mm)
S
(17.53)
.690
(17.53)
.690
Dimension A =
.268” (6.8mm) for on-none-on
.319” (8.1mm) for on-off-on & on-on-on
N
A
A
DP only with .323”
(8.2mm) Actuator
Support Bracket Mount
(For Terminals 13, 30, & 40)
Maximum Panel Thickness:
For Straight PC with Bracket Terminal 13: .197” (5.0mm)
For Angle Mount Terminals 30 & 40: .177” (4.5mm)
Keylocks
01
03
Solder Lug
Epoxy Seal
(4.0)
.157
Straight PC
Rotaries
(2.0)
(1.1) .079
.043
Thk = (0.8)
.031
(1.17)
.046
Thk = (0.8)
.031
13
Straight PC with Bracket
30
Right Angle PC
40
Vertical PC
TYPICAL SWITCH DIMENSIONS
Solder Lug Terminals
Single Pole
(1.2) R Typ
.047
(1.1) x (2.0) Typ
.043 x .079
(6.1)
.240
(0.8) Typ
.031
3
ON
(17.53)
.690
(12.7)
.500
2
(3.8)
.150
(4.7) Typ
.185
1
Tilt
(19.6)
.772
ON
H
(6.35)
(4.8) .250
.189
Epoxy Seal
(2.0)
.079
Tactiles
Slides
(2.4) Dia Typ
.094
(2.4) Dia Typ
.094
Panel Mount
(Combines with Solder
Lug Terminal 01 only)
(3.8)
.150
(6.6)
.260
(0.4)
.016
(5.1) (6.4) (4.5)
.201 .252 .177
Touch
MS12AFW01
(0.5)
.020
(2.0)
.079
Actuator in LEFT Position
Solder Lug Terminals
Double Pole
(1.2) R Typ
.047
Indicators
(0.5)
.020
(1.1) x (2.0) Typ
.043 x .079
(1.2) R Typ
.047
(2.0) Typ
.079
(17.53)
.690
(19.6)
.772
(3.8)
.150
Supplement
(6.1)
.240
(3.8)
.150
(6.1)
.240
(8.2)
.323
MS22BFW01
H34
ON
Accessories
(17.53)
.690
(19.6)
.772
ON
(0.8) Typ
.031
(0.4)
.016
(5.1) (6.4) (4.5)
.201 .252 .177
(4.7) Typ
.185
(0.5)
.020
Actuator in LEFT Position
www.nkk.com
6
3
5
2
4
1
(4.8)
.189
(11.4)
.449
(12.7)
.500
(0.5)
.020
Series MS
Toggles
Miniature Slides
TYPICAL SWITCH DIMENSIONS
(0.8) Typ
.031
Actuator in LEFT Position
Double Pole
5
2
4
1
(4.8)
.189
(6.35)
.250
1
4
(0.5)
.020
MS22BNG03
Single Pole
(3.8)
.150
(4.8)
.189
Straight PC Terminals with Bracket
(3.2)
.126
(0.4) Typ
.016
(1.2) Typ
.047
ON
ON
Actuator in LEFT Position
Double Pole
(8.2)
.323
ON
(4.8)
.189
ON
(3.8)
.150
(0.8) Typ
.031 (15.8)
(4.7) Typ .622
.185
(0.36)
.014
(10.4)
.409
(10.4)
.409
(5.1)
.201
(6.7)
.264
(14.3)
.563
MS12ASG13
Straight PC Terminals with Bracket
(3.2)
.126
(0.4) Typ
.016
(1.8) Dia Typ
.073
(1.5) Dia Typ
.059
(0.5)
.020
(1.17)
.046
Tilt
(7.1)
.280
(3.8)
.150
(4.7) Typ
.185
1
1
(6.7)
.264
(13.1)
.516
(5.1)
.201
2
(12.7)
.500
2
(0.36)
.014
(5.6)
.220
(7.9) Typ
.311
3
(0.8) Typ
.031
(15.8)
(4.7) Typ .622
.185
H
(1.6) Typ
.063
3
(3.8)
.150
Pushbuttons
(1.8) Dia Typ
.073
Actuator in LEFT Position
(4.7) Typ
.185
2
4
1
(12.7)
.500
(0.5)
.020
(4.8)
.189
(11.9)
.469
Actuator in LEFT Position
www.nkk.com
3
6
2
5
1
4
3
5
(1.17) Typ
.046
(1.6) Typ
.063
(2.4) Typ
.095
(1.2) Typ
.047
6
Slides
5
Tactiles
(7.6)
.299
6
2
Rotaries
(4.8)
.189
(11.4)
.449
(12.7)
.500
CL
Touch
ON
(5.1)
.201
3
6
(4.7) Typ
.185
(4.8)
.189
3
Keylocks
(1.17) Typ
.046
ON
(8.2)
.323
(3.8)
.150
MS12ANG03
Straight PC Terminals
(0.8) Typ
.031
(3.8)
.150
(1.8) Dia Typ
.073
(0.5)
.020
(1.17)
.046
Indicators
(5.1)
.201
1
1
(4.8)
.189
(6.4) (6.35)
.252 .250
(4.7) Typ
.185
Programmable Illuminated PB
ON
ON
(4.7) Typ
.185
2
(12.7)
.500
2
(3.8)
.150
(6.6)
.260
3
3
(7.9) Typ
.311
(4.7) Typ
.185
Accessories
(3.8)
.150
Straight PC Terminals
Rockers
Single Pole
(1.8) Dia Typ
.073
(1.5) Dia Typ
.059
MS22BSG13
H35
Supplement
Series MS
Toggles
Miniature Slides
TYPICAL SWITCH DIMENSIONS
Single Pole
Rockers
Right Angle PC Terminals
(5.1)
.201
(3.8)
.150
(12.7)
.500
1
Pushbuttons
(3.8)
.150
(5.7)
.224
Programmable Illuminated PB
MS12ASG30
(1.2)
.047
(9.53)
.375
(1.27)
.050
(1.8) Dia Typ
.073
(4.7) Typ
.185
3
(6.6)
.260
(3.2)
(3.81) .126
.150
(0.4) Typ
.016
(13.2)
.520
2
3
2
(9.53)
.375
(0.8) Typ
.031
(4.7) Typ
.185
(0.5)
.020
Double Pole
(3.8)
.150
(5.1)
.201
(3.8)
.150
(12.7)
.500
4
5
6
Keylocks
6
(8.2)
.323
(3.8)
.150
(0.4) Typ
.016
(13.2)
.520
(6.2)
.245
(1.2)
.047
(12.7)
.500
(5.7)
.224
(13.2)
.520
MS22BSG30
(11.4)
.449
(3.2)
.126
(0.5)
.020
1
Tactiles
Tilt
(0.8) Typ
.031
(4.7) Typ
.185
(1.5) Dia Typ
.059
(6.6) Typ
.260
3
3
ON
(0.4)
.016
(10.16)
.400
(3.81) Typ
.150
2
(12.7)
.500
2
(6.9)
.270
1
1
(10.16)
.400
(0.8) Typ (2.7)
.031
.106
(3.81) Typ
.150
(6.6)
.260
(1.27)
.050
(0.5)
.020
(4.45) Typ
.175
(1.5) Dia Typ
.059
Actuator in LEFT Position
Vertical PC Terminals
Double Pole
(3.8)
.150
(5.1)
.201
(11.4)
.449
ON
(8.2)
.323
(3.8)
.150
(1.2) Typ
.047
(4.45)
.175
(1.2) Typ
.047
(4.45)
.175
(6.9)
.270
ON
Touch
(12.7)
.500
(1.8) Dia Typ
.073
(5.3)
.209
MS12ASG40
Indicators
(3.81)
.150
1
3
(5.1)
.201
(1.2) Typ
.047
(4.45)
.175
Accessories
2
3
Single Pole
(3.8)
.150
(3.8)
.150
Supplement
(1.8) Dia Typ
.073
(4.7) Typ
.185
5
4
Actuator in LEFT Position
Vertical PC Terminals
H36
2
(1.27) Typ
.050
(3.81)
.150
ON
Slides
Rotaries
(0.4) Typ
.016
MS22BSG40
(6.6) Typ
.260
(1.5) Dia Typ
.059
Actuator in LEFT Position
Right Angle PC Terminals
H
1
(5.3)
.209
(0.4)
.016
(12.7)
.500
(0.8) Typ (2.7)
.031
.106
(3.81) Typ
.150
Actuator in LEFT Position
www.nkk.com
(0.5)
.020
6
3
5
2
4
3
(12.7)
.500
(1.8) Dia Typ
.073
(4.8)
.189
6
2
5
1
4
(3.81) Typ
.150
1
(1.27) Typ
.050
(4.8)
.189
(12.7)
.500
(4.45) Typ
.175
(1.5) Dia Typ
.059
Toggles
Series MS
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Other Ratings
Programmable Illuminated PB
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: Keylocks
Materials & Finishes
Actuator:
Frame:
Case:
Movable Contacts:
Stationary Contacts:
Terminals:
Rotaries
Slides
Tactiles
Power Level:
H
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
Tilt
Processing
Touch
Miniature Illuminated Slides
Soldering Time & Temp: Cleaning: Standards & Certifications
Flammability Standards:
10 milliohms maximum
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts & case for 1 minute minimum
50,000 operations minimum
25,000 operations minimum Nonshorting (break-before-make)
.087” (2.2mm)
Polyamide (UL94V-0)
Stainless steel
Glass fiber reinforced diallyl phthalate resin (UL94V-0)
Silver alloy
Silver capped copper with silver plating Copper or brass with silver plating
–10°C through +55°C (+14°F through +131°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering Recommended (PC version): See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
Note: Lever must be in center position while soldering.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL94V-0 rated actuator & case
Supplement
Accessories
Indicators
6A @ 125V AC or 3A @ 250V AC
H38
www.nkk.com
Toggles
Series MS
Miniature Illuminated Slides
Rockers
Distinctive Characteristics
Pushbuttons
Bright, LED illumination at top of actuator.
Programmable Illuminated PB
Over-center actuator block and plunger design gives crisp
actuation, diminishes sparking, and increases operating life.
Guide interlocked with actuator block prevents
window locking and maintains correct plunger
alignment to assure contact stability.
High internal barriers between poles and
insulating sheet between case and actuator
block give added protection to contacts.
H
Tactiles
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Slides
Rotaries
Keylocks
Antijamming design protects contacts from
damage due to excessive downward force
on the actuator.
Actual Size
Supplement
Accessories
Indicators
Clinching of frame to case well above base and terminals provides
1,500V dielectric strength.
Touch
Tilt
Epoxy sealed terminals prevent entry of flux, solvents,
and other contaminants.
www.nkk.com
H39
Series MS
Toggles
Miniature Illuminated Slides
TYPICAL SWITCH ORDERING EXAMPLE
Pushbuttons
Rockers
MS
1
2
Programmable Illuminated PB
Poles
1
L
F
W
L
LED Lighted
Mounting
2
ON
NONE
ON
3
ON
OFF
ON
Rotaries
Keylocks
LEDS
Silver; Rated
6A @ 125V AC &
3A @ 250V AC
W
Circuits
C
Contact Materials
& Ratings
Illumination
SPDT
01
C
Red
E
Yellow
F
Green
Terminals
N
For Straight PC
(Terminal 03 only)
F
With 2-screw Flange
(Terminal 01 only)
01
Solder Lug *
03
Straight PC
*Wire harness &
cable assemblies
offered only in
Americas
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
H
Red LED Illumination
2-screw Flange Frame
Silver Contacts with 6-Amp Rating
Tactiles
Slides
MS12LFW01C
SPDT ON-NONE-ON Circuit
Tilt
Solder Lug Terminals
Slide Position
Pole
SP
Supplement
Connected Terminals
Left
Center
Right
MS12
ON
NONE
ON
MS13
ON
OFF
ON
Left
Center
Throw & Schematics
Right
Model
Accessories
Indicators
Touch
POLES & CIRCUITS
Note: Terminal numbers are not actually on
the switch. LED circuit is isolated and
requires an external connection.
2 (COM)
2-1
OPEN
2-3
SPDT
L(+)
1
3
4
CONTACT MATERIALS & RATINGS
W
H40
Silver over Silver
Power Level
www.nkk.com
6A @ 125V AC & 3A @ 250V AC
L(-)
6
Series MS
Toggles
Miniature Illuminated Slides
03
2-screw Flange
(Combines with Solder
Lug Terminal 01 only)
01
Straight PC
(6.35) (4.8)
.250 .189
Epoxy Seal
(1.17) Typ
.046
(2.0)
.079
(4.0)
.157
Epoxy Seal
Solder Lug
Pushbuttons
(4.8)
.189
Thk = (0.8) Typ
.031
(6.35) (4.8)
.250 .189
Programmable Illuminated PB
F
Straight PC Mount
(Combines with
Straight PC Terminal
03 only)
(2.0)
.079
(1.1)
.043
(1.17)
.046
(4.8)
.189
Thk = (0.8) Typ
.031
LED COLORS & SPECIFICATIONS
Color
(-)
C
E
Red
Yellow
F
Green
Keylocks
(+)
Forward Peak Current
IFM
30mA
30mA
25mA
Typical Forward Current
IF
16mA
16mA
16mA
Forward Voltage
VF
1.98V
2.06V
2.16V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.42mA/°C
0.33mA/°C
Ambient Temperature Range
Rotaries
LEDs are supplied as an integral part
of the switch (not available separately). The lamp circuit is independent of
switch operation. Electrical specifications shown are determined at a basic
temperature of 25°C.
If the source voltage exceeds the
rated voltage, a ballast resistor is
required. The resistor value can
be calculated by using the formula
given in the Supplement.
–15° ~ +60°C
H
TYPICAL SWITCH DIMENSIONS
Slides
N
Rockers
MOUNTING TYPES & TERMINALS
(2.0) Typ
.079
(6.1)
.240
(8.2)
.323
(5.1)
.201
(12.7)
.500
2
(4.7) Typ
.185
(17.53)
.690
1
4
(0.5)
.020
(4.8)
.189
(11.9)
.469
(0.4) (4.5)
.016 .177
(7.6) (6.35)
.299
.250
(6.8)
.268
(9.0)
.354
Maximum Panel Thickness .197” (5.0mm)
Actuator in LEFT Position
Tilt
(3.8)
.150
Direction of Actuation
3
6
(17.53)
.690
(19.6)
.772
(2.0)
.079
(2.4)
.094 Dia Typ
MS12LFW01C
Straight PC Terminals
(1.17) Typ
.046
(0.8) Typ
.031
(3.8)
.150
(2.0)
.079
(8.2)
.323
(4.7) Typ
.185
(5.1)
.201
(7.6)
.299
(4.8)
.189
(6.35)
.250
Actuator in LEFT Position
2
(12.7)
.500
(4.8)
.189
(11.9)
.469
6
(4.7) Typ
.185
2
1
1
4
(4.8)
.189
3
3
(0.5)
.020
(6.8)
.268
4
(1.8) Dia Typ
.073
(9.0)
.354
Direction of Actuation
6
Maximum Panel Thickness .197” (5.0mm)
www.nkk.com
Accessories
Circuit Mark
This Side
(5.0)
.197
Touch
(1.17) Typ
.046
(1.1) x (2.0) Typ
.043 x .079
(0.8) Typ
.031
Indicators
Circuit Mark
This Side
MS12LNW03C
H41
Supplement
(5.0)
.197
Tactiles
Solder Lug Terminals
(1.2) R Typ
.047
Toggles
Series SM
Ultra-Miniature Slides
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Programmable Illuminated PB
Other Ratings
Keylocks
Materials & Finishes
Rotaries
Slides
Tactiles
Tilt
Touch
Indicators
Contact Resistance:
Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Nominal Operating Force:
Contact Timing:
Total Travel:
H
Actuator:
Case:
Lower Case:
Movable Contacts:
Stationary Contacts
Terminals:
Environmental Data
Operating Temp Range: Humidity: Vibration: Shock: 30 milliohms maximum
100 megohms minimum @ 500V DC
500V AC for 1 minute minimum
1,000 operations minimum
1,000 operations minimum
2.0N
Nonshorting (Break-before-make)
.063” (1.6mm)
Glass fiber reinforced polyester (UL94V-0)
Glass fiber reinforced polyamide (UL94V-0)
Glass fiber reinforced polyester (UL94V-0)
Brass with gold plating over nickel
Brass with gold plating over nickel
Brass with gold plating over nickel
–40°C through +85°C (–40°F through +185°F) 90-95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
PCB Processing
Soldering: Wave Soldering Recommended: See Profile A in Supplement section.
Manual Soldering: See Profile B in Supplement section.
Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: Actuator and lower case of glass fiber reinforced polyester and case of glass fiber reinforced polyamide UL94V-0
The SM series devices have not been tested for UL recognition and CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended in a low-voltage, low-current circuit, the results do not produce
hazardous energy.
Supplement
Accessories
Maximum Level: 500mA @ 12V DC
Minimum Level: 1.0mA maximum @ 10mV AC/DC maximum
H42
www.nkk.com
Series SM
Toggles
Ultra-Miniature Slides
Rockers
Distinctive Characteristics
Pushbuttons
Very compact dimensions allow for high density, side-by-side or
end-to-end mounting within tight dimensional applications.
Programmable Illuminated PB
Detent mechanism provides positive actuation to indicate
circuit status.
Twin sliding contact mechanism with self-cleaning action
provides smooth actuation and produces high contact reliability.
Keylocks
Visible indication of position by spot on top of red actuator
and through window on side.
Actual Size
H
Tactiles
Insert molded terminals lock out flux, solvents, and other contaminants.
POLES & CIRCUITS
Connected Terminals
Throw & Schematics
Right
Center
Left
Right
Center
Left
ON
NONE
ON
1-3
OPEN
1-2
Model
Note: Terminal numbers are
on the switch.
Tilt
Slide Position
Slides
Rotaries
.100” x .100” (2.54mm x .2.54mm) center-to-center inch terminal
spacing allows standard PC board mounting in side-by-side or
end-to-end arrangements.
3
2
TYPICAL SWITCH DIMENSIONS
Single Pole • Straight PC
2
2
(1.4)
.055
(0.5)
.020
(6.4)
.252
(2.54) Typ
.100
(5.0)
.197
(10.0)
.394
1
3
(0.8) Dia Typ
.031
Supplement
1
3
(2.54) Typ
.100
Accessories
(0.6) Dia Typ
.024
(1.6) Travel
.063
(2.5)
.098
Actuator shown in RIGHT position
SM0320102
www.nkk.com
Indicators
SPDT
Touch
1 (COM)
SM0320102
H43
Toggles
Series SS
Ultra-Miniature Slides
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Programmable Illuminated PB
Pushbuttons
Power Level (silver):
Logic Level (gold):
Other Ratings
Keylocks
Indicators
Touch
Tilt
Tactiles
Slides
Rotaries
Materials & Finishes
H
Actuator:
Upper Case:
Lower Case:
Movable Contactor:
Interior Base:
Terminals:
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
PCB Processing
Soldering: Cleaning:
20 milliohms maximum for power level; 40 milliohms maximum for logic level
100 megohms minimum @ 500V DC
500V AC minimum 1 minute minimum
10,000 operations minimum
10,000 operations minimum
SS12S & SS22S – Shorting (make-before-break)
.079” (2.0mm)
Polyamide
Polyester for 3-On models; polyacetal for all other models
Glass fiber reinforced polyester for 3-On models;
glass fiber reinforced polybutylene terephthalate (thermoplastic) for other models
Phosphor bronze with silver plating (code 2) or
phosphor bronze with gold plating (code 4)
Phenolic resin (thermoset)
Brass with silver plating over copper plating or brass with gold plating
–15°C through +60°C (+5°F through +140°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering: For non-supported through-hole, see Profile B in Supplement section.
For supported through-hole, 5 seconds maximum @ 250°C maximum.
Manual Solder: See Profile B in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
The SS series devices have not been tested for UL recognition and CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended in a low-voltage, low-current circuit, the results do not produce
hazardous energy.
Supplement
Accessories
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: 0.1A @ 30V DC
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
H44
www.nkk.com
Toggles
Series SS
Ultra-Miniature Slides
Rockers
Distinctive Characteristics
Pushbuttons
Top or side actuation permits flexible board design.
Programmable Illuminated PB
Compact dimensions and low profile allow
high density mounting and close stacking of
PC boards.
Crisp actuation positively indicates circuit status.
Keylocks
Double molded thermoset base and thermoplastic housing prevent loosening of terminals
due to high soldering temperatures.
H
Insert molded terminals lock out flux, solvents, and other contaminants.
Touch
Tilt
Tactiles
Inch or metric terminal spacing for standard PC board grid (.100” x .100” or 2.0mm x 2.0mm).
Slides
Rotaries
Award-winning STC mechanism with benefits
unavailable in conventional mechanisms: smoother,
positive detend actuation, increased contact stability,
and unparalleled logic-level reliability. (Additional STC
details in Terms and Acronyms in the Supplement section.)
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
H45
Series SS
Toggles
Ultra-Miniature Slides
Rockers
SS
Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
Poles & Circuits
Programmable Illuminated PB
12S
SPDT
ON
12S
NONE
D
P
2
Terminal Spacing
ON
SS12S model has shorting contacts.
* 14M
SP3T
ON
ON
ON
22S
DPDT
ON
NONE
ON
B
Metric 2.0mm x 2.0mm
D
Inch .100” x .100”
Contact Material
& Ratings
2
Silver Rated 0.1A @ 30V DC
*4
Gold Rated 0.4VA maximum
@ 28V AC/DC maximum
* Gold not available with SS14M.
SS22S model has shorting contacts.
See Poles & Circuits chart below.
Actuation
Rotaries
Keylocks
* 14M Circuit with silver contacts only.
P
Top Actuated
H
Side Actuated
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Slides
SS12SDP2
H
Top Actuated
Tilt
Tactiles
Silver Contacts Rated 0.1A @ 30V DC
Touch
Indicators
Accessories
Terminals with .100” Spacing
POLES & CIRCUITS
Slide Position
Supplement
SPDT ON-NONE-ON Circuit
Right
Pole
Model
SP
SS12S
Center
Connected Terminals
Left
Right
Center
Throw & Schematics
Left
Note: Terminal numbers are not actually on switch.
ON
NONE
ON
2-1
NONE
2-3
SPDT
3
SP
SS14M
ON
ON
ON
3-4
3-2
3-1
SP3T
DP
SS22S
ON
NONE
ON
2-1 5-4
NONE
2-3 5-6
DPDT
4
3 (COM)
1
H46
www.nkk.com
2 (COM)
2
2 (COM)
1
ON-OFF-ON circuit
can be created by not
connecting terminal 2.
1
3
4
5 (COM)
6
Series SS
Toggles
Ultra-Miniature Slides
Metric 2.0mm x 2.0mm with Black Base
(2.0) Typ
.079
(0.6) Typ
.024
(3.4)
.134
(10.2)
.402
(3.4)
.134
(10.0)
.394
(6.0)
.236
1
2
3
(4.0)
.157
(2.0) Typ
.079
(0.6) Typ
.024
(4.0)
.157
(2.0) Typ
.079
4
1
5
6
2
4
(2.0) Typ
.079
(4.0)
.157
3
2
1
3
(0.8) Dia Typ
.031
(0.8) Dia Typ
.031
(2.0) Typ
.079
(0.8) Dia Typ
.031
(2.0)
.079
On-None-On Single Pole Models
On-None-On Double Pole Models
3-On Models
Inch .100” x .100” with Gray Base
(0.4) Typ
.016
(2.54) Typ
.100
(0.6) Typ
.024
(4.0)
.157
(0.4) Typ
.016
(2.54) Typ
.100
(3.4)
.134
(0.4) Typ
.016
(2.54)
.100
(5.08)
.200
(2.54) Typ
.100
(0.6) Typ
.024
(4.0)
.157
(3.4)
.134
(0.6) Typ
.024
(10.2)
.402
(6.54)
.257
Keylocks
D
(3.4)
.134
Pushbuttons
(2.0) Typ
.079
(0.6) Typ
.024
(4.0)
.157
(0.4) Typ
.016
(2.0)
.079
Programmable Illuminated PB
(0.4) Typ
.016
(0.4) Typ
.016
(10.2)
.402
(3.4)
.134
Rotaries
B
Rockers
TERMINAL SPACING
4
2
5
2
6
3
3
(0.8) Dia Typ
.031
On-None-On Single Pole Models
3
(5.08)
.200
2
1
(0.8) Dia Typ
.031
(2.54) Typ
.100
(2.54)
.100
(0.8) Dia Typ
.031
On-None-On Double Pole Models
3-On Models
Top Actuated
(2.0)
.079
(1.2)
.047
(1.5)
.059
H
Side Actuated
(2.5)
.098
(1.2)
.047
Touch
P
Tilt
ACTUATION
(1.5)
.059
Silver over Phosphor Bronze
Power Level
0.1A @ 30V DC
4
Gold over Silver/Phosphor Bronze
Logic Level
0.4VA max @ 28V AC/DC max
Supplement
2
Accessories
Indicators
CONTACT MATERIALS & RATINGS
Complete explanation of operating range in Supplement section.
www.nkk.com
H
Slides
(2.54) Typ
.100
1
Tactiles
1
4
(2.54) Typ
.100
H47
Series SS
Toggles
Ultra-Miniature Slides
TYPICAL SWITCH DIMENSIONS
Single & Double Pole
Rockers
Top Actuated
(3.3)
.130
Pushbuttons
(2.0) Travel
.079
Programmable Illuminated PB
(1.2)
.047
(1.5)
.059
(2.0)
.079
(1.2)
.047
(4.0)
.157
(3.0)
.118
(0.6) Typ
.024
(2.54) Typ
.100
(0.4)
.016
(4.5)
.177
(6.54)
.257
1
3
2
5
3
6
SS12SDP2
Side Actuated
Single & Double Pole
Keylocks
(3.3)
.130
(2.0) Travel
.079
(3.3)
.130
(1.2)
.047
(3.5)
.138
(2.0) Travel
.079
(0.6) Typ
.024
1
2
(1.5)
.059
(2.5)
.098
Rotaries
Slides
(10.2)
.402
(0.4) Typ
.016
(2.54)
.100
(0.4)
.016
(1.5)
.059
(2.5)
.098
(5.0)
.197
(6.54)
.257
(4.0)
.157
(2.54) Typ
.100
(0.4)
.016
(3.0)
.118
3
(10.2)
.402
H
3-On Circuit • Top Actuated
(0.4)
.016
Single Pole
(0.4)
.016
Tactiles
(2.0) Travel Typ
.079
(0.6) Typ
.024
(5.08)
.200
4
3
2
(1.5)
.059
(2.0)
.079
Tilt
(1.2)
.047
(4.0)
.157
(4.5)
.177
(2.54) Typ
.100
(3.0)
.118
(15.8)
.622
1
(0.4)
.016
SS14MDP2
3-On Circuit • Side Actuated
Single Pole
Indicators
(3.5)
.138
(0.4)
.016 (0.6) Typ
.024
(2.0) Travel Typ
.079
Accessories
(5.08)
.200
4
3
2
Supplement
(1.5)
.059
(2.5)
.098
(4.0)
.157
(1.2)
.047
(5.0)
.197
SS14MDH2
H48
(2.54) Typ
.100
(3.0)
.118
www.nkk.com
1
4
2
5
3
6
(10.2)
.402
(0.4) Typ
.016
(2.54)
.100
SS12SDH2
Touch
4
1
(10.2)
.402
2
(15.8)
.622
1
(0.4)
.016
Toggles
Series SS
Ultra-Miniature Illuminated Slides
Rockers
Distinctive Characteristics
Pushbuttons
Top or side actuation permits flexible board design.
Programmable Illuminated PB
Bright, LED illumination at tip of actuator.
Compact dimensions and low profile allow
high density mounting and close stacking
of PC boards.
Keylocks
Crisp actuation positively indicates
circuit status.
H
Tactiles
Sliding twin contact mechanism with self-cleaning action
provides smooth actuation and produces high contact reliability.
Slides
Rotaries
Double molded thermoset base and
thermoplastic housing prevent loosening
of terminals due to high soldering temperatures.
Tilt
Insert molded terminals lock out flux, solvents, and other contaminants.
Touch
Inch terminal spacing for standard PC board grid (.100” x .100”).
Supplement
Accessories
Indicators
Actual Size
www.nkk.com
H49
Toggles
Series SS
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Pushbuttons
Power Level:
Other Ratings
Programmable Illuminated PB
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: Materials & Finishes
Rotaries
Keylocks
Actuator:
Upper Case:
Lower Case:
Movable Contactor:
Interior Base:
Terminals:
Tactiles
Slides
Environmental Data
H
Operating Temp Range:
Humidity: Vibration:
Shock:
Touch
Tilt
PCB Processing
Soldering: Cleaning:
0.1A @ 30V DC
20 milliohms maximum
100 megohms minimum @ 500V DC
500V AC minimum 1 minute minimum
10,000 operations minimum
10,000 operations minimum
Shorting (make-before-break)
.079” (2.0mm)
Polyacetal
Polyacetal
Glass fiber reinforced polyester
Phosphor bronze with silver plating
Phenolic resin (thermoset)
Brass with silver plating over copper plating
–15°C through +60°C (+5°F through +140°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering: For non-supported through-hole, see Profile B in Supplement section.
For supported through-hole, 5 seconds maximum @ 250°C maximum.
Manual Soldering: See Profile B in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
The SS series devices have not been tested for UL recognition and CSA certification.
These switches are designed for use in a low-voltage, low-current circuit.
When used as intended in a low-voltage, low-current circuit, the results do not produce
hazardous energy.
Supplement
Accessories
Indicators
Ultra-Miniature Illuminated Slides
H50
www.nkk.com
Series SS
Toggles
Ultra-Miniature Illuminated Slides
P
Poles & Circuits
2
L
C
LED Colors
Actuation
12S
SPDT
ON
NONE
ON
P
Top Actuated
C
Red
22S
DPDT
ON
NONE
ON
H
Side Actuated
E
Yellow
F
Green
D
Contact Material
& Ratings
Inch .100” x .100”
LED Circuit
L
Isolated
Keylocks
Terminal Spacing
Pushbuttons
D
Programmable Illuminated PB
12S
Silver Rated
0.1A @ 30V DC
2
Rotaries
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
SS12SDP2LC
Red LED
Top Actuated
SPDT ON-NONE-ON Circuit
Silver Contacts Rated 0.1A @ 30V DC
H
Slides
SS
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
Tactiles
Terminals with .100” Spacing
POLES & CIRCUITS
Model
SP
SS12S
Center
Left
Right
Center
Left
ON
NONE
ON
2-1
NONE
2-3
Note: Terminal numbers are not actually on switch.
Isolated LED circuit requires external power source.
SPDT
3
DP
SS22S
ON
NONE
ON
2-1 5-4
NONE
2-3 5-6
2 (COM)
DPDT
1
2 (COM)
3
4
(+)
(-)
(+)
(-)
1
5 (COM)
6
Single Pole Models
(0.4) Typ
.016
(2.54) Typ
.100
(3.4) Typ
.134
(9.0)
.354
(0.4) Typ
.016
(2.54) Typ
.100
(0.6) Typ
.024
(13.0)
.512
(2.54) Typ
.100
(3.4) Typ
.134
Double Pole Models
www.nkk.com
(9.0)
.354
(2.54) Typ
.100
(0.6) Typ
.024
Supplement
Inch .100” x .100”
Accessories
TERMINAL SPACING
D
Tilt
Right
Throw & Schematics
Touch
Pole
Connected Terminals
Indicators
Slide Position
(13.0)
.512
H51
Series SS
Toggles
Ultra-Miniature Illuminated Slides
CONTACT MATERIALS & RATINGS
Rockers
2
Silver over Phosphor Bronze
Power Level
0.1A @ 30V DC
TYPICAL SWITCH DIMENSIONS
Pushbuttons
Single & Double Pole
Top Actuated
(2.54)
.100
L (+)
Programmable Illuminated PB
(2.0) Travel
.079
(0.4)
.016
(2.54)
.100
(0.6) Typ
.024
(0.3) Typ
.012
1
(13.0)
.512
L (-)
3
(2.54) Typ
.100
(3.0)
.118
(2.5)
.098
(2.5)
.098
(3.7)
.146
(9.0)
.354
2
(2.54) Typ
.100
L (+)
1
2
(0.3) Typ
.012
L (+)
L (-)
(0.6) Typ
.024
(0.4) Typ
.016
(4.5)
.177
(0.8) Dia Typ
.031
(13.0)
.512
6
(2.54) Typ
.100
(0.6) Typ
.024
(0.4) Typ
.016
4 L (+)
1
5
2
6 L (-)
3
Keylocks
Side Actuated
(2.54)
.100
L (+)
(3.7)
.146
Rotaries
Slides
(2.54)
.100
(0.6) Typ
.024
(0.4)
.016
(0.3) Typ
.012
1
3
1
(13.0)
.512
H
L (+)
4
L (-)
6
3
2
(0.8) Dia Typ
.031
(2.54) Typ
.100
(2.5)
.098
(0.6) Typ
.024
(0.4) Typ
.016
(7.5)
.295
(3.0)
.118
(0.6) Typ
.024
(4.5)
.177
(9.0)
.354
4 L (+)
1
5
2
6 L (-)
3
Tactiles
Tilt
(2.54) Typ
.100
(0.8) Dia Typ
.031
SS12SDH2LC
LED COLORS & SPECIFICATIONS
LEDs are supplied as an integral part
of the switch (not available separately). The lamp circuit is independent of
switch operation. Electrical specifications shown are determined at a basic
temperature of 25°C.
If the source voltage exceeds the rated
voltage, a ballast resistor is required.
The resistor value can be calculated
by using the formula given in the
Supplement.
L
Isolated,
1-element
(+)
(-)
Color
C
E
Red
Yellow
30mA
30mA
25mA
Typical Forward Current
IF
16mA
16mA
16mA
Forward Voltage
VF
1.98V
2.06V
2.16V
Reverse Peak Voltage
VRM
5V
5V
5V
Current Reduction Rate Above 25°C
∆IF
0.40mA/°C
0.42mA/°C
0.33mA/°C
Ambient Temperature Range
AT4065 Slide Cap
Cap can be assembled on request
Cap Color: Black only
H52
Green
IFM
–15° ~ +60°C
OPTIONAL CAP
Material: Polycarbonate
F
Forward Peak Current
Indicators
Touch
(2.54) Typ
.100
3
L (-)
(13.0)
.512
5
2
1
(2.54) Typ
.100
(4.85)
.191
(7.5)
.295
L (-)
(0.4) Typ
(0.3) Typ
.016
.012
(2.54) Typ
.100
L (+)
2
(2.5)
.098
Accessories
SS22SDP2LC
Single & Double Pole
(2.0) Travel
.079
Supplement
(2.54) Typ
.100
(0.8) Dia Typ
.031
(2.54) Typ
.100
3
L (-)
4
5
2
3
1
(3.2)
.126
(5.0)
.197
(5.0)
.197
(11.0)
.433
(8.5)
.335
(0.6)
.024
www.nkk.com
Window color should match LED color.
Colors Available:
C Red
E Yellow
F Green
Toggles
Series SS3
Ultra-Miniature SMT Slides
Rockers
Distinctive Characteristics
Pushbuttons
Compact dimensions and low profile allow high density mounting and close stacking
of PC boards.
Programmable Illuminated PB
Crisp actuation positively indicates circuit status.
Heat resistant resin allows vapor phase and
infrared convection reflow soldering.
Keylocks
Award-winning STC mechanism with benefits
unavailable in conventional mechanisms:
smoother, positive detent actuation, increased
contact stability, and unparalleled logic-level
reliability. (Additional STC details in Terms
and Acronyms in the Supplement section.)
Rotaries
Insert molded terminals lock out flux, solvents, and other contaminants.
H
Tactiles
Gull-wing terminals provide mechanical stability during soldering and simplified
solder joint inspection.
Slides
Metric terminal spacing for standard PC board grid (2.0mm x 2.0mm ).
Packaged in tape-reel or partitioned tray. Tape-reel packaging meets EIA-481-D Standard.
Indicators
Touch
Tilt
Coplanarity: all considered surfaces must lie between two parallel planes that are a maximum
distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in
the Supplement section.)
Supplement
Accessories
Actual Size
www.nkk.com
H53
Toggles
Series SS3
Ultra-Miniature SMT Slides
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Programmable Illuminated PB
Pushbuttons
Logic Level:
Other Ratings
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: 50 milliohms maximum
100 megohms minimum @ 500V DC
500V AC minimum for 1 minute minimum
10,000 operations minimum
10,000 operations minimum
SS312S ~ Shorting (make-before-break)
.079” (2.0mm)
Keylocks
0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Note: Find additional explanation of operating range in Supplement section.
Materials & Finishes
Slides
Rotaries
Actuator:
Housing:
Base:
Movable Contactor:
Terminals:
H
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
–25°C through +85°C (–13°F through +185°F)
90 ~ 95% humidity for 240 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Tilt
Tactiles
Polyphenylene sulfide
Phosphor bronze with tin plating (UL94V-0)
Polyphenylene sulfide (UL94V-0)
Phosphor bronze with gold plating over silver plating (code 4)
Phosphor bronze with gold plating
Soldering: Cleaning:
Standards & Certifications
Flammability Standards: Reflow Soldering Recommended. See Profile A in Supplement section.
Manual Soldering: See Profile A in Supplement section.
These devices are not process sealed. Hand clean locally using alcohol based solution.
UL 94V-0 rated housing & base
The SS3 Series slides have not been tested for UL recognition or CSA certification.
These switches are designed for use in a low-voltage, low-current, logic-level circuit.
When used as intended in a logic-level circuit, the results do not produce hazardous energy.
Supplement
Accessories
Indicators
Touch
Installation
H54
www.nkk.com
Toggles
Series SS3
Ultra-Miniature SMT Slides
A
H
Poles & Circuits
SPDT
ON
NONE
Actuation
H
ON
Packaging
Side Actuated
14M
SPDT
ON
OFF
ON
SP3T
ON
ON
ON
Tape-Reel
500 Pieces/Reel
No
Code
Partitioned Tray
Keylocks
SS312S model has shorting contacts.
R
Rotaries
For 3-on: External connection must be
made during installation; see
Poles & Circuits chart.
A
H
Contact Material
& Rating
Metric 2.0mm x 2.0mm
Gold Rated 0.4VA maximum
@ 28V AC/DC maximum
Tilt
4
Tactiles
Terminal Spacing
Slides
12S
4
Pushbuttons
14M
Programmable Illuminated PB
SS3
Rockers
TYPICAL SWITCH ORDERING EXAMPLE
Touch
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Gold Contacts with 0.4VA Rating
Indicators
SS314MAH4
SPDT ON-OFF-ON Circuit
Side Actuated
Supplement
Accessories
2.0mm x 2.0mm Terminal Spacing
www.nkk.com
H55
Series SS3
Toggles
Ultra-Miniature SMT Slides
POLES & CIRCUITS
Slide Position
Pushbuttons
Rockers
Right
Pole
Model
SP
SS312S
Left
Right
Center
Throw & Schematics
Left
Note: Terminal numbers are not actually on switch.
ON
NONE
ON
2-3
NONE
2-1
SPDT
Programmable Illuminated PB
1
ON
SP
OFF
ON
3-5
4-2
3-1
SPDT
1
2 (COM)
2
3 (COM)
SS314M
ON
ON
ON
3-5
3-4
3-1
SP3T
1
2
3 (COM)
4
5
External Connection
3
4
5
External connection
must be made during
installation to create
ON-ON-ON circuit.
Keylocks
TERMINAL SPACING
Metric 2.0mm x 2.0mm
Rotaries
A
(0.17) Typ
.0067
(0.6) Typ
.024
(2.0) Typ
.079
(9.2)
.362
(4.0)
.157
H
(0.17) Typ
.0067
(0.6) Typ
.024
(2.0) Typ
.079
(12.5)
.492
(1.7)
.067
(1.4)
.055
(9.8)
.386
Tactiles
Slides
Center
Connected Terminals
(5.6)
.220
3
2
1
(4.2)
.165
(2.55)
.1004
(1.4)
.055
(1.7)
.067
(13.1)
.516
(2.0) Typ
.079
(1.0) Typ
.039
(1.7) Typ
.067
SS312
(5.6)
.220
(2.55)
.1004
5
4
3
2
1
(2.0) Typ
.079
(1.0) Typ
.039
(1.7) Typ
.067
SS314
Tilt
ACTUATION
Side Actuated
Touch
H
(2.0)
.079
Indicators
(1.2)
.049
(1.5)
.059
Accessories
CONTACT MATERIALS & RATING
Supplement
4
Gold over Silver/Phosphor Bronze
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Complete explanation of operating range in Supplement section.
H56
www.nkk.com
Series SS3
Toggles
Ultra-Miniature SMT Slides
TYPICAL SWITCH DIMENSIONS
Single Pole
Coplanar Dimension
Programmable Illuminated PB
(2.0)
.079
(1.2)
.047
(10.5)
.413
(2.0) Typ
.079
Pushbuttons
(2.0) Travel
.079
(9.2)
.362
Rockers
(1.4)
.055
(0.6) Typ
.024
1 2 3
(1.35)
.053
(0.7)
.028
(1.5)
.059
(5.45)
.2146
(4.0)
.157
(2.9)
.114
(0.2) Typ
.0079
(0.95) Typ
.0374
1
(0.17)
.0067
(2.0)
.079
2
3
(0.15) Max
.0059
SS312SAH4
Single Pole
(5.6)
.220
(1.4)
.055
1 2 3 4 5
(1.5)
.059
(2.0) Travel Typ
.079
(12.5)
.492
(2.0)
.079
(1.2)
.047
Keylocks
(1.35)
.053
(0.7)
.028
(0.6) Typ
.024
(13.8)
.543
Rotaries
Nonshorting Contacts
(2.0) Typ
.079
Coplanar Dimension
(4.2)
.165
H
(2.9)
.114
(0.95) Typ
.0374
(0.2) Typ
.0079
(2.0)
.079
(0.17)
.0067
1
2 3 4 5
(0.15) Max
.0059
Tactiles
SS314MAH4
Tilt
PACKAGING
Partitioned Tray
Accessories
Indicators
Touch
If the SS3 is ordered in less
than 500-piece increments,
the switches are packaged in
a partitioned tray. No code
is required.
Supplement
No
Code
Slides
Shorting Contacts
www.nkk.com
H57
Series SS3
Toggles
Ultra-Miniature SMT Slides
PACKAGING
Rockers
R
Tape-Reel Packaging
Pushbuttons
Switches must be ordered in 500-piece
increments when tape-reel packaging is
selected.
Programmable Illuminated PB
Tape-reel packaging meets EIA-481-D
Standard.
Tape-Reel Packaging for SS312SAH4
Each tape-reel of 530 pockets contains 500 switches.
Overall Dia (330.0)
13.0
(16.0)
.630
(21.0) Dia
.827
(2.0)
.079
(7.5)
.295
(1.5) Dia Typ
.059
(3.3)
.130
Direction of Feed
(16.4)
.646
Reel Dimensions
Tactiles
(12.0) Typ
.472
(3.0) Typ
.118
(78.49) Dia
3.090
(13.0) Dia
.512
H
(16.0) Typ
.630
(2.0) Typ
.079
Terminal #3
Rotaries
(4.0) Typ
.157
(1.75)
.069
(2.0) Typ
.079
Slides
Minimum Trailer Length: 6.93” (176mm)
Part No.
Keylocks
Minimum Leader Length: 11.97” (304mm)
(0.5)
.020
Tape Dimensions
Tape-Reel Packaging for SS314MAH4
Tilt
Each tape-reel of 530 pockets contains 500 switches.
Minimum Trailer Length: 8.66” (220mm)
Touch
Minimum Leader Length: 14.96” (380mm)
(78.49) Dia
3.090
(13.0) Dia
.512
Supplement
Accessories
(2.0) Typ
.079
Overall Dia (330.0)
13.0
(16.0)
.630
(21.0) Dia
.827
(2.0)
.079
(7.5)
.295
Direction of Feed
(16.4)
.646
Reel Dimensions
H58
(14.8) Typ
.583
Tape Dimensions
www.nkk.com
(1.5) Dia Typ
.059
(3.3)
.130
Part No.
(1.75)
.069
(20.0) Typ
.787
(2.0) Typ
.079
Terminal #5
Indicators
(4.0) Typ
.157
(0.5)
.020