Toggles Series HB2 Rockers General Specifications Electrical Capacity (Resistive Load) Keylocks Programmable Illuminated PB Pushbuttons Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: Materials & Finishes Housing: Base: Movable Contact: Switch Terminals: Lamp Terminals: Environmental Data Slides D Operating Temperature Range: Humidity: Vibration: Shock: Tactiles Rotaries Subminiature Audio/Video Pushbuttons Installation Cap Installation Force: 80 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 100,000 operations minimum for momentary; 100,000 operations minimum 1.8N Pretravel .051” (1.3mm); Overtravel .020” (0.5mm); Total Travel .071” (1.8mm) Glass fiber reinforced polyamide Glass fiber reinforced polyamide Phosphor bronze with gold plating Phosphor bronze with gold plating Steel with silver plating –25°C through +50°C (–13°F through +122°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) 15.0N (3.37 lbf) maximum downward force on cap Soldering: Wave Soldering: See Profile A in Supplement section. Manual Soldering: See Profile B in Supplement section. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications The HB2 pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. Supplement Accessories Indicators Touch Tilt PCB Processing D18 www.nkk.com Toggles Series HB2 Rockers Distinctive Characteristics Pushbuttons Quiet actuation combined with crisp tactile feedback suited for broadcast equipment. Full face illumination with choice of red/green or red/yellow bicolor LEDs, as well as simultaneous bicolor illumination which produces amber. D Option of legends on caps or film insert. Keylocks Compact design with short body .669” (17.0mm) from PCB to top of cap and .295” (7.5mm) square cap. Programmable Illuminated PB Subminiature Audio/Video Pushbuttons Rotaries Sliding Twin Crossbar (STC) mechanism provides unequalled logic-level reliability, contact stability, smooth positive detent actuation, and long life. Slides Crimped power terminals ensure secure PCB mounting and prevent dislodging during soldering. Touch Tilt Tactiles Suitable applications include broadcast, telecommunication, and medical equipment, as well as measuring instruments, etc. Supplement Accessories Indicators Actual Size www.nkk.com D19 Series HB2 Toggles Subminiature Audio/Video Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Rockers Pushbuttons 5 Pole 1 S K Shape S SPST D OFF Square JB Cap Colors Gold Contacts and PC Terminals, Rated 0.4VA @ 28V AC/DC G03 (ON) K LEDs Black CE Red/Yellow CF Red/Green Amber can be achieved by simultaneous illumination of LEDs. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE HB215SKG03CF-JB Red/Green LED Clear Lens/ White Diffuser JB Housing ( ) = Momentary Clear Lens with White Diffuser Black Housing SPST OFF–(ON) Circuit Rotaries CF Contacts & Terminals Square Shape Gold Contacts & PC Terminals with 0.4VA @ 28V AC/DC Rating POLE & CIRCUIT Slides Tactiles G03 Circuit 5 Keylocks Programmable Illuminated PB 1 HB2 Plunger Position ( ) = Momentary Normal Pole Down Connected Terminals Normal Down Model Throw & Switch/Lamp Schematics Notes: Switch terminals are not marked on the switch. Red LED terminal is marked with “R”. Lamp circuit is isolated and requires external power source. Red Tilt 3 (+) HB215 SP OFF (ON) OPEN 1-2 4 (-) SPST 1 2 5 (+) Yellow or Green Touch HOUSING SHAPE & COLOR S K Indicators .307” (7.8mm) Square Body Black Housing CONTACT MATERIALS, RATINGS & TERMINALS Accessories G03 CL Gold Contacts Logic Level Supplement Switch Terminal (0.4) .016 (0.5) Sq .020 D20 (3.5) .138 0.4VA maximum @ 28V AC/DC maximum Lamp Terminal (0.4) .016 (0.5) Sq .020 www.nkk.com (3.5) .138 PCB Footprint (0.5) .020 (2.5) Typ .098 (5.0) .197 (1.0) Dia .039 (0.85) Dia Typ .033 (2.25) Typ .089 (1.0) Dia .039 3 4 5 (4.5) .177 1 2 (0.92) .036 (2.54) .100 Series HB2 Toggles Subminiature Audio/Video Pushbuttons BICOLOR LEDS & SPECIFICATIONS CF Color Red/Yellow Red/Green Unit Forward Peak Current IFM 30/30 30/30 mA Typical Forward Current IF 20/20 20/20 mA Forward Voltage VF 2.0/2.1 2.0/2.1 V Reverse Peak Voltage VRM 4/4 4/4 V Current Reduction Rate Above 25°C ∆IF 0.33/0.33 0.33/0.33 mA/°C Cathode – R = Where: R = E = VF = IF = E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) Ambient Temperature Range –25° ~ +50°C D The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is isolated and requires external power source. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. CAP COLORS Clear Transparent Lens AT3081 Square Lens B White Translucent Diffuser (1.0) .039 AT3082 Square Diffuser (7.5) Sq .295 Lens & Diffuser Material: Polycarbonate Lens Finish: Glossy Keylocks (3.5) .138 (5.8) Sq .228 Rotaries J Diffuser Finish: Frosted TYPICAL SWITCH DIMENSIONS Single Pole (1.4) .055 (0.8) Dia Typ .031 (2.54) .100 3 (7.5) Sq .295 (0.5) Sq Typ .020 2 (0.4) .016 (3.5) .138 (3.1) .122 (5.0) .197 5 (4.5) .177 (7.8) Sq .307 (11.7) .461 (17.0) .669 R 4 1 (0.92) .036 Square (0.5) Sq Typ .020 Tactiles Pushbuttons VF E Rockers CE LED is an integral part of the switch. Anode Programmable Illuminated PB IF Slides + (0.5) .020 HB215SKG03CF-JB Tilt R LEGENDS Touch NKK Switches can provide custom legends for caps. Contact factory for more information. Suggested Printable Area for HB2 Lens & Film Insert Indicators Recommended Methods: Screen Print or Pad Print on Lens; Laser Print on Film Insert. Epoxy based ink is recommended. Lens Film Insert: Clear Polyester, 4 mil max. thickness Diffuser Lens Film Insert (5.98) Sq .235 (7.5) Sq .295 (0.76) Typ .030 (5.7) Sq .224 (4.17) Sq .164 (0.76) Typ .030 Supplement UP Film Insert Accessories (0.6) R .024 Shaded areas are printable areas. www.nkk.com D21