Download Specifications

ISC15ANP4
Version (1)
DISTINCTIVE CHARACTERISTICS
•
•
•
•
•
•
•
•
•
•
Organic LED technology; now with 30,000 hours life and 30% less power consumption
Range of 65,536 colors in 16 bit mode, 256 colors in 8 bit mode
Full viewing angle of 180°
Exceptional contrast: 50 times greater than previous LCD products
Four times more enhanced resolution
High resolution provides sharp, clear images of very small characters
Operated by commands and data supplied via serial communications (SPI)
Distinct, long travel of 4.5mm (same as KP01 Series)
Dust tight construction
Stylish, translucent black housing design
Viewing area: 15.5mm x 11.6mm (horizontal x vertical)
High reliability and long life of three million actuations
minimum
High resolution of 64RGB x 48 pixels
Epoxy sealed straight PC terminals
Snap-in standoff for easy, secure mounting and alignment
Actual Size
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com
2
OLED SMARTSWITCH
TM
SWITCH DESCRIPTION
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Switch Description
OLED
Pixel Format
SPST, Momentary ON
Gold Contacts
Straight PC Terminals
Color OLED
Display Module
65,536 Colors
64RGB x 48 Pixels
Horizontal x Vertical
SWITCH SPECIFICATIONS
Circuit
SPST normally open
Contact Position
Leave actuator: 1 – 2 OFF
Push actuator: 1 – 2 ON
Electrical Capacity (Resistive Load)
100mA @ 12V DC
Contact Resistance
200 milliohms maximum @ 20mV 10mA
Insulation Resistance
100 megohms minimum @ 100V DC
Dielectric Strength
125V AC for 1 minute minimum
Mechanical Endurance
3,000,000 operations minimum
Electrical Endurance
3,000,000 operations minimum
Operating Force
2.0 ± 0.5 Newtons
Total Travel
4.5mm (.177”)
OLED SPECIFICATIONS
Characteristics of Display
Display Device
Color OLED display module
Display Mode
Passive matrix
Viewing Area
15.5mm x 11.6mm (horizontal x vertical)
Pixel Format
64RGB x 48 pixels (horizontal x vertical)
Pixel Size
0.21mm x 0.20mm (horizontal x vertical)
Interface
Serial (SPI) interface
Number of Colors
65,536 Colors (16bit: R 5bit/G 6bit/B 5bit)
or 256 Colors (8bit: R 2bit/G 3bit/B 3bit)
Operating Temperature Range
–20°C ~ +70°C (–4°F ~ +158°F)
Storage Temperature Range
–30°C ~ +80°C (–22°F ~ +176°F)
Operating Life (Display)
30,000 hours (at 40% pixels ON)
Absolute Maximum Ratings
Recommended Operating Conditions
Items
Symbols
Items
Ratings
Symbols Minimum
Typical
Maximum
2.4V
2.8V
3.5V
VCC
15.0V
16.0V
17.0V
VI H
0.8 x VDD
––
––
VI L
––
––
0.2 x VDD
–0.3V to +4.0V
Supply Voltage for
Logic/Interface
VDD
VCC
–0.0V to +19.0V
Supply Voltage for Drive
VI
–0.3V to VD D +0.3V
Input High Level Voltage
Input Low Level Voltage
Supply Voltage for
Logic/Interface
VDD
Supply Voltage for Drive
Input Voltage
Current Consumption
Optical Characteristics (Temperature at 25°C, Initial Value: 87 x 0F)
(Temperature at 25°C, VDD = 2.8V, VCC = 16.0V)
Items
Symbols Min Typical
Max
Items
All-Pixels-On Mode
*Drive System Power Current
I CC1
––
All-Pixels-On Mode
*Logic/IF System Power Current
I DD1
–– 0.16mA 0.19mA
White Color
Coordinate
Sleep Mode
**Drive System Power Current
I CC2
––
Red Color
Coordinate
Sleep Mode
**Logic/IF System Power Current
I DD2
––
3.8mA
––
––
4.6mA
10μA
10μA
* All pixels shall be turned on with the maximum level gray scale
** All pixels shall be turned off (while chip is operating)
Luminosity
Green Color
Coordinate
Blue Color
Coordinate
Contrast Ratio
(x)
(y)
(x)
(y)
(x)
(y)
(x)
(y)
Min
Typical
Max
Unit
75
100
125
cd/m
0.26
0.32
0.63
0.29
0.19
0.61
0.10
0.14
100
0.30
0.37
0.67
0.33
0.23
0.65
0.14
0.20
––
0.34
0.42
0.71
0.37
0.27
0.69
0.18
0.26
––
––
––
––
––
––
––
––
––
––
Remarks
2
White
(All pixels on)
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com
3
OLED SMARTSWITCH
TM
SWITCH BLOCK DIAGRAM & PIN CONFIGURATIONS
Color OLED Panel
64RGB x 48
SR1,SG1,SB1......SR64,
SG64,SB64
COM1....COM48
Segment Driver
Common Driver
OLED Driver
with Controller
VDD
3
VCC
9
RES
5
SEG/COM
Driving Block
Gray Scale
Decoder
SCK
7
SS
4
SDI
8
D/C
6
Oscillator
Graphic Display
Data
RAM
96 x 64 x 16 Bit
Display Timing
Generator
Command Decoder
MCU Interface
OLED SMARTSWITCHTM
GND 10
SW
Pin No.
Symbol
2
1
Name
Function
1
2
3
4
SW
SW
VDD
SS
Terminal of Switch
Terminal of Switch
Power
Slave Select
Normally open
Normally open
Power source for logic circuit
Slave select for SPI. This line is active low.
5
RES
Reset
Reset signal input. When pin is low, initialization of chip is
executed.
6
D/C
Data/Command
7
8
SCK
SDI
VCC
GND
Serial Clock
Serial Data In
Power
Ground
9
10
Data/Command Control. When pin is pulled low, data will
be interpreted as Command; when pulled high, data will be
interpreted as Data.
Clock line for SPI that synchronizes command and data
Data input line for SPI
Power source for drive circuit
Connect to Ground
TYPICAL SWITCH DIMENSIONS
See
Pixel Detail
Terminal numbers are not on the switch.
(3.3)
.130
(13.41)
.528
(18.0)
.709
Standoff 1
Standoff 2
(0.6) Typ
.024
(20.59)
.811
(9.57)
.377
(16.0)
.630
(0.4) Typ
.016
(0.74)
.029
See Standoff
Detail
(15.5)
.610
(23.0)
.906
(23.13)
.911
Pixel Detail
(0.03) Typ
.0012
(1.0) Typ
.039
2
(11.6)
.457
(0.20) Typ
.0079
SW
(0.21) Typ
.0083
(0.03) Typ
.0012
See Pixel
Detail A
Pixel Detail A
(0.20)
.0079
(0.17)
.0067
(0.04) Typ
.0016
(0.07) Typ
.0028
(0.2)
.008
R
9
4
1
Standoff 1
(0.3) Typ
.012
(8.0)
.315
(1.25)
.049
(2.0) Dia
.079
Dimension A
Standoff 1 = (2.7) Standoff 2 = (2.3)
.091
.106 (0.2) Typ
.008
(2.0)
.079
(7.05)
.278
2x (0.9) Dia
.035
(18.0)
.709
Footprint
A
(7.0)
.276
3
Standoff 2
R G B R
(0.21)
.0083
(7.62)
.300
(3.4)
.134
Standoff Detail
10
(1.0) Typ
.039
(7.0)
.276
9
3
2
10
(7.62)
.300
4
1
8x (0.75) Dia
.029
(2.0)
.079
(7.05)
.278
(8.0)
.315
(16.0)
.630
4x (1.3) Dia
.051
Landless
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com
4
OLED SMARTSWITCH
TM
TIMING SPECIFICATIONS
AC Characteristics (Temperature at 25°C), VDD = 2.4V ~ 3.5V)
Items
Symbols Minimum
Typical
Maximum
Clock Cycle Time
t c yc le
150ns
––
––
D/C Setup Time
t AS
40ns
––
––
D/C Hold Time
t AH
40ns
––
––
SS Setup Time
t CSS
75ns
––
––
SS Hold Time
t CSH
60ns
––
––
Write Data Setup Time
t DSW
40ns
––
––
Write Data Hold Time
t DHW
40ns
––
––
SCK Low Time
t CLKL
75ns
––
––
SCK High Time
t CLKH
75ns
––
––
SCK Rise Time
tR
––
––
15ns
SCK Fall Time
tF
––
––
15ns
D/C
SS
t AS
tA H
t CSS
t CS H
tR
t CLKH
t cy cl e
SCK
t CLKL
tF
t DSW
t DH W
D7
SDI
D6
D5
D4
D3
D2
D1
D0
STATE TRANSITION
7 : Initialization
1 : Power ON, 7 : Initialization
State 0
Power OFF
(VCC, VDD O FF)
2 : Power OFF
State 1
Display OFF
(Sleep Mode)
3 : Display ON
4 : Display OFF
8 : Changing the Display
State
Number
State
0
Power OFF
Display Sleep
OFF
––
VC C
VD D
Changing the
Display
OFF
OFF
Disable
1
Display OFF
OFF
ON
ON
ON
Enable
2
Display ON
ON
OFF
ON
ON
Enable
Transition
1
Power ON
2
Power OFF
Refer to
3
Display ON
"Power ON/OFF Sequence"
4
Display OFF
7
Initialization
Initialize Setting of Command/Data
Image Rewriting
Send Display Data
Display Settings
Dimmer, Scroll, etc.
8
8 : Changing the Display
Power ON/OFF Sequence
Initialization Setting
State 0
Power ON
State 1
State 2
Power OFF
State 0
Minimum 0µs
Minimum 0µs
VDD
State Transition
State 2
Display ON
0V
Index
Reset low pulse width Trw
(minimum 3µs)
RES
“L” or “Hi-z”
“L” or “Hi-z”
Minimum 3µs
Minimum 0µs
VCC
D/C
SS
“L” or “Hi-z”
SCK
SDI
VDD level (due to ESD protection
circuit between VDD and VCC)
“H” or “L”
“L” or “Hi-z”
Note: Refer to Application Notes on web site.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com
5
OLED SMARTSWITCH
TM
PRECAUTIONS FOR HANDLING & STORAGE OF OLED DEVICES
ATTENTION
ELECTROSTATIC
SENSITIVE DEVICES
Handling
1. The IS Series OLED devices are electrostatic sensitive. To avoid damage to IC, do not touch terminals unless properly isolated from static electricity.
2. Signal input under conditions not recommended may cause damage to the OLED unit or deterioration of the display. Follow directions regarding supply sequences of power and signal voltages.
3. If the OLED panel is broken, avoid touching the contents. Wash off any contact to the skin or clothing.
4. Limit operating force to switch keytop to 100.0N maximum, as excessive pressure may damage the OLED.
5. Recommended soldering time and temperature limits:
11 seconds maximum @ 270°C maximum; avoid temperatures exceeding 80°C at the OLED.
6. The IS series OLED devices are not process sealed.
7. Pixels acquire diminished brightness over time and use, and those most frequently habituated have greater reduction of brightness than those less used. To minimize this difference, operate OLED unit so that all pixels are used as consistently as possible.
8. Clean cap surface with dry cloth. If further cleaning is needed, wipe with dampened cloth using neutral cleanser and dry with clean cloth. Do not use organic solvent.
Storage
1. Store in original container and away from direct sunlight.
2. Keep away from static electricity.
3. Avoid extreme temperatures, high humidity, gaseous substances, and all forms of chemical contamination.
NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkksmartswitch.com
6