Download Specifications

Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Toggles
Series M
Miniature Rockers
General Specifications
B
Electrical Capacity (Resistive Load)
Power Level (silver): 6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits
Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum
(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Logic/Power Level (gold over silver): Combines silver & gold ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
Other Ratings
Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
50,000 operations minimum
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
25°
Materials & Finishes
Actuator Clip & Mounting Frame:
Body Frame:
Case:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Terminals:
Stainless Steel
Stainless steel
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Copper or brass with silver plating; or copper or brass with gold plating
Operating Temp Range: Humidity: Vibration: Shock: Processing
Soldering: Cleaning: –30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
Wave Soldering (PC version) for Gold: See Profile A in Supplement section.
Manual Soldering for Gold: See Profile A in Supplement section.
Wave Soldering (PC version) for Silver: See Profile B in Supplement section.
Manual Soldering for Silver: See Profile B in Supplement section.
Note: Actuator must be in OFF (center) position while soldering.
These devices are not process sealed. Hand clean locally using alcohol based solution.
Standards & Certifications
Flammability Standards: UL94V–0 for case
UL: File No. E44145 - Recognized only when ordered with marking on switch.
Add “/U” before first dash in part number to order UL recognized switch.
All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch.
Add “/C” before first dash in part number to order CSA certified switch.
All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. Supplement
Accessories
Indicators
Touch
Tilt
Tactiles
Environmental Data
B62
www.nkk.com
Distinctive Characteristics
B
Pushbuttons
Three methods of panel mounting: flat frame for flush with face or subpanel,
snap-in, and PCB.
Rockers
Toggles
Series M
Miniature Rockers
Programmable Illuminated PB
High insulating barriers increase isolation of circuits in multipole devices
and provide added protection to contact points.
The molded diallyl phthalate case has a UL 94V-0
flammability rating.
Epoxy sealed terminals prevent entry of solder flux
and other contaminants.
Keylocks
Prominent external insulating barriers increase
insulation resistance and dielectric strength.
Slides
Rotaries
Bias guard prevents misalignment of contacts;
interlocking of actuator block with rocker and
internal guide does not allow transmission of
diagonal force on rocker to reach contact
mechanism.
Snap-in Mount
Page B64
Flat Frame Mount
www.nkk.com
Page B83
B63
Supplement
Accessories
Bracket PC Mount Page B72
Indicators
Actual Size
Touch
Tilt
Tactiles
Clinching of the frame to the case well above the base
and terminals provides 1,500V dielectric strength.
Snap-In Mount Miniature Rockers
B
TYPICAL SWITCH
M20
1
TJ
2
W
F
01
Poles
Rockers & Paddles
1
SPDT
2
DPDT
SP3T
F
.450” (11.43mm) Wide Rocker
Terminals
G
.450” (11.43mm) Wide Paddle
01
Solder Lug
S
02
Quick Connect
.453” (11.5mm) False
Illluminated Rocker in Black only
03
.250” (6.35mm)
Straight PC
05
.425” (10.8mm)
Wirewrap
Rocker & Paddle
Colors
06
.750” (19.05mm)
Wirewrap
A
Black
.964” (24.5mm)
Wirewrap
B
White
07
C
Red
08
1.062” (27.0mm)
Wirewrap
E
Yellow
Mounting Frame
TJ
Snap-in Frame
Circuits
2
ON
3
ON
OFF
ON
5
ON
NONE
(ON)
8
(ON)
OFF
(ON)
9
ON
OFF
(ON)
*4
ON
ON
ON
F
Green
*6
(ON)
ON
(ON)
G
Blue
*7
ON
ON
(ON)
H
Gray
NONE
ON
( ) = Momentary
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Toggles
Series M
Contact Materials & Ratings
W
Silver; Rated
6A @ 125V AC & 3A @ 250V AC
G
Gold; Rated
0.4VA max @ 28V AC/DC max
A
Gold over Silver; Rated
6A @ 125V AC & 0.4VA max @
28V AC/DC max
Touch
Tilt
Tactiles
* 3-ON circuits
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Indicators
M2012TJW01-FC-1A
Accessories
Red .450” (11.43mm)
Wide Rocker
Black Bezel without LED
SPDT
ON-NONE-ON Circuit
Snap-in Frame
Silver Contacts with
6–Amp Rating
Supplement
Solder Lug Terminals
B64
www.nkk.com
C
Series M
ORDERING EXAMPLE
A
Bezel with 2 Round LEDs
4
Bezel with 2 Rectangular
LEDs
White
E
Yellow
F
Green
G
Blue
H
Gray
A
Black
A
Programmable Illuminated PB
B
1 LED
C
Red
F
Green
2 LEDs
Black
Top LED
Bottom LED
C
Red
C
Red
E
Yellow
E
Yellow
F
Green
F
Green
Tactiles
3
Black
Keylocks
Bezel with 1 Round LED
A
IMPORTANT:
Touch
Tilt
Switches are supplied without UL & CSA marking unless specified.
UL & CSA recognized only when ordered with marking on the switch.
Specific models, ratings, & ordering instructions are noted on the
General Specifications page.
DESCRIPTION FOR TYPICAL ORDERING EXAMPLE
Red .450” (11.43mm)
Wide Rocker
Indicators
M2012TJW01-FC-3A-CF
Top LED Red
Bottom LED Green
Snap-in Frame
Accessories
2
Bezel without LED
LED Colors
Black Bezel with
2 Round LEDs
SPDT ON-NONE-ON Circuit
Silver Contacts with
6–Amp Rating
Solder Lug Terminals
Supplement
1
Bezel Colors
Rotaries
Optional Bezels
Pushbuttons
B
Slides
1
Rockers
Toggles
Snap-In Mount Miniature Rockers
www.nkk.com
B65
Series M
Toggles
Snap-In Mount Miniature Rockers
POLES & CIRCUITS
Rocker Position
) = Momentary
Programmable Illuminated PB
Pushbuttons
Rockers
(
B
Connected Terminals
Down
Center
Up
Down
Pole
Model
SP
M2012
M2013
M2015
M2018
M2019
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
M2022
M2023
M2025
M2028
M2029
ON
ON
ON
(ON)
ON
NONE
OFF
NONE
OFF
OFF
ON
ON
(ON)
(ON)
(ON)
DP
Throw & Schematics
Center
Up
Note: Terminal numbers are not
actually on the switch.
SPDT
2-3
OPEN
2 (COM)
2-1
3
1
DPDT
2-3 5-6
OPEN
2
2-1 5-4
3
(COM)
1
5
6
4
For 3 Throw (3-On)
Pole
Model
Down
Center
Up
SP
M2024
M2026
M2027
ON
(ON)
ON
ON
ON
ON
ON
(ON)
(ON)
Rotaries
Keylocks
Connected Terminals & Schematic
External
Connection
2 (in)
5
Slides
1 (out)
3 4 (out) 6 (out)
2-3 5-6
External
Connection
2 (in)
5
1 (out)
External Connection
The SP3T model utilizes a double pole
base.
External
Connection
2 (in)
5
3 4 (out) 6 (out)
2-3 5-4
1 (out)
3 4 (out) 6 (out)
External
connection
must be made
during field
installation.
(out)
External
Conn
6
3
5
2
4
1
(out)
Common
(in)
(out)
2-1 5-4
Tactiles
TJ
Tilt
MOUNTING FRAME
(18.0)
.710
Panel Cutout for
Single Pole
without Bezel
Snap-in Frame
Touch
Panel Cutout for
Double Pole
without Bezel
(12.5)
.492
25°
(2.54) Dia
.100
(12.2)
.480
(15.9)
.626
(4.3)
.170
(15.9)
.626
(13.1)
.516
Panel Thickness without Bezel: .039” ~ .126” (1.0mm ~ 3.2mm)
Panel Thickness with Bezel: .039” ~ .098” (1.0mm ~ 2.5mm)
Accessories
Indicators
CONTACT MATERIALS & RATINGS
W
Silver over Silver
Power Level
6A @ 125V AC & 3A @ 250V AC
G
Gold over Brass or Copper
Logic Level
0.4VA maximum @ 28V AC/DC maximum
Note: See Supplement section to find complete explanation of operating range.
Supplement
A
Gold over Silver
Power Level or Logic Level
6A @ 125V AC
or 0.4VA maximum @ 28V AC/DC maximum
Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the
same application. See Supplement section to find complete explanation of dual rating and operating range.
B66
www.nkk.com
Series M
TERMINALS
.062” (1.57mm) Wide
Quick Connect
02
(4.0)
.157
(2.0)
.079
(2.0)
(1.1) .079
.043
Thk = (0.8)
.031
(1.57)
.062
Thk = (0.8)
.031
(4.8)
.189
.250” (6.35mm)
Straight PC
3
(6.35)
(4.8) .250
.189
Epoxy Seal
2
(4.7) Typ
.185
1
.425” (10.8mm)
Wirewrap or Extended PC
06
.750” (19.05mm)
Wirewrap or Extended PC
07
.964” (24.5mm)
Wirewrap or Extended PC
08
1.062” (27.0mm)
Wirewrap or Extended PC
6
2
5
1
4
(1.8) Dia Typ
.073
(1.17)
.046
Thk = (0.8)
.031
05
3
Programmable Illuminated PB
03
B
(6.35)
.250
Epoxy Seal
Pushbuttons
Epoxy Seal
(4.7) Typ
.185
(1.8) Dia Typ
.073
Single Pole
Double Pole
If using as extended PC terminal, refer to
the above footprints.
Epoxy Seal
A
Keylocks
Solder Lug
Dimension A = terminal lengths as shown
beside the terminal codes
at the left.
(1.27)
.050
Thk = (0.8)
.031
Rotaries
01
(9.19)
.362
Material: Polyamide
Finish: Matte
(11.43)
.450
(16.36)
.644
(5.84) R
.230
Colors Available:
A, B, C, E, F, G, H
(11.43)
.450
(11.8)
.465
(1.8)
.071
Touch
(1.8)
.071 (11.8)
.465
AT466 .453” (11.5mm)
False Illuminated Rocker
(8.6)
.339
False Illuminator
Acrylonitrile Butadiene Styrene
(11.3)
.445
Indicators
Rocker
Material:
Polycarbonate
Finish:Glossy
Colors:
Black
(7.7)
.303
White and Red
(1.8)
.071
(11.5)
.453
Accessories
S
(2.36)
.093
Material: Polyamide
Finish: Matte
(7.11)
(6.3) .280
.248
Colors Available:
A, B, C, E, F, G, H
AT4151
.450” (11.43mm)
Wide Paddle
Tactiles
G
Tilt
AT4150
.450” (11.43mm)
Wide Rocker
Slides
ROCKERS & PADDLES
F
(11.8)
.465
A
Black
B
White
C
Red
E
Yellow
www.nkk.com
F
Green
G
Blue
H
Supplement
When a bezel is selected with AT466, glossy polycarbonate AT207 is supplied.
Cap Colors
Available:
Rockers
Toggles
Snap-In Mount Miniature Rockers
Gray
B67
Series M
OPTIONAL SNAP-IN BEZELS & BEZEL COLORS
1
B
A
AT2107 Bezel
Material: Polyamide
White
Yellow
Blue
H
Gray
A
(12.5)mm
.492”
(13.1)mm
.516”
B
(6.25)mm
.246”
(6.55)mm
.258”
(30.2)
1.19
AT212 Bezel
for AT617 LED
A
(12.0)
.472
(10.0)
.394
Finish:
Semi-glossy
(8.0)
.315
Tilt
Touch
Finish:
Semi-glossy
(10.0)
.394
(15.9)
.626
A
Single Pole Double Pole
A
A
(12.0)
.472
(2.2)
.087
(18.4)mm
.724”
Black
(21.5) Sq
.846
(18.7)mm
.736”
(15.9)
.626
LED colors &
specifications
on next page.
(7.8)
.307
(11.8)
.465
(5.0) Typ
.197
A
LED colors &
specifications
on next page.
(2.2)
.087
(7.8)
.307
(11.8)
.465 (21.5) Sq
.846
(2.0) Typ
.079
(8.0)
.315
(15.9)
.626
A
Single Pole Double Pole
A
(18.4)mm
.724”
(18.7)mm
.736”
Bezel Assembly
1. Pry out tab on bezel to
a 45° angle.
Accessories
Indicators
AT213 Bezel
for AT618 LED
(8.8) Dia
.346
(13.8)
.543
Black
Tactiles
(3.0) Dia Typ
.118
(13.1)mm
.516”
B
Single Pole Double Pole
(15.6)
.614
(12.5)mm
.492”
LED colors & specifications
on next page.
(2.2)
.087
(13.5)
.531
(5.4) Dia
.213
Material:
Polycarbonate
Single Pole Double Pole
Black
(12.0)
.472
Contact factory
for matte finish.
4
(15.9)
.626
A
(11.8)
.465
(19.0)
.748
Finish: Glossy
3
G
Green
(21.5)
.846
A
Material:
Polycarbonate
Slides
(12.0)
.472
AT208 Bezel
for AT070 LED
Material:
Polycarbonate
F
Black
A
E
(2.2)
.087
(15.6)
.614
2
B
(11.8)
.465
Finish: Matte
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
Toggles
Snap-In Mount Miniature Rockers
Tab
2. Insert switch frame under
tab and snap on bezel.
45°
Supplement
Tab
B68
www.nkk.com
3. Push tab back into place.
4. Snap assembled bezel
and switch into panel.
Series M
Toggles
Snap-In Mount Miniature Rockers
LED COLORS & SPECIFICATIONS
(7.0)
.276
(5.0)
.197
Top LED
Circuit Mark This Side
Circuit Mark This Side
Top LED
Bottom LED
(+)
(-)
Bottom LED
(-)
Programmable Illuminated PB
(7.7)
.303
(5.0)
.197
Pushbuttons
(3.0) Dia
.118
B
(-)
(+)
(+)
Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+).
AT617
AT618
Keylocks
AT070
C
F
C
E
F
C
E
F
Color
Red
Green
Red
Yellow
Green
Red
Yellow
Green
Maximum Forward Current
IFM
25mA
50mA
30mA
30mA
25mA
25mA
30mA
25mA
Typical Forward Current
IF
20mA
30mA
20mA
20mA
20mA
20mA
20mA
20mA
Forward Voltage
VF
2.8V
2.1V
2.0V
2.1V
2.2V
2.25V
2.1V
2.2V
Maximum Reverse Voltage
VRM
4V
5V
5V
5V
5V
5V
5V
5V
Current Reduction Rate
Above 25°C
∆IF
0.33
mA/°C
0.40
mA/°C
0.40
mA/°C
0.40
mA/°C
0.33
mA/°C
0.33
mA/°C
0.40
mA/°C
0.33
mA/°C
(-)
Ambient Temperature Range
(when used with a bezel)
–10° ~ +70°C
–15° ~ +70°C
–25° ~ +70°C
Tactiles
(+)
The electrical specifications shown are determined at a basic temperature of 25°C.
LED circuit is independent of switch operation. LED is colored in OFF state.
Tilt
If the source voltage is greater than the rated voltage of the LED, a ballast resistor must be connected in series with the lamp.
The ballast resistor calculation and more lamp detail are shown in the Supplement section.
Touch
LEGENDS
Indicators
NKK Switches can provide custom legends for caps. Contact factory for more information.
Suggested Printable Area for Cap
(0.38) Typ
.015
Accessories
(4.5) Typ
.177
F
OF
ON
(0.76) Typ
.030
Pad Print
Epoxy based ink is recommended.
AT4150
www.nkk.com
(9.91)
.390
(11.43)
.450
(0.76) Typ (3.36) Typ
.132
.030
Supplement
Recommended Print Method:
Rotaries
(5.08) Dia
.200
AT618 LED
For Bezel AT213
with 2 Rectangular LEDs
Slides
AT617 LED
For Bezel AT212
with 2 Round LEDs
Circuit Mark This Side
AT070 LED
For Bezel AT208
with 1 LED
Rockers
Bezel Orientation on Switch
Shaded areas are printable areas.
B69
Series M
Toggles
Snap-In Mount Miniature Rockers
TYPICAL SWITCH DIMENSIONS
(4.9)
.194
(2.8) Circuit Mark
.110 This Side
(1.1) x (2.0) Typ
.043 x .079
3
(18.0)
.709
(4.7) Typ
.185
25°
(0.5)
.020
(7.1)
.279
(3.3)
.130
(13.0)
.512
2
(0.8) Typ
.031
(11.43)
.450
(12.2)
.480
1
(2.0) Typ
.079
(0.5)
.020
(9.4)
.371
(7.9)
.311
(4.5)
.177
M2012TJW01-FC
Snap-in Frame • Solder Lug
Double Pole
(4.9)
.194
Keylocks
Programmable Illuminated PB
Single Pole
B
Pushbuttons
Rockers
Snap-in Frame • Solder Lug
Rotaries
(18.0)
.709
(2.8) Circuit Mark
.110 This Side
(4.7) Typ
.185
25°
(0.8) Typ
.031
(11.43)
.450
(12.2)
.480
(0.5)
.020
(7.1)
.279
(3.3)
.130
(4.8)
.189
(1.1) x (2.0) Typ
.043 x .079
3
6
5
2
4
1
(13.0)
.512
(0.5)
.020
(9.4)
.371
(2.0) Typ
.079
(4.5)
.177
(12.7)
.500
Slides
M2022TJW01-FC
Snap-in Frame • Solder Lug
Single Pole
(2.8)
.110
Tactiles
Circuit Mark
This Side
(1.1) x (2.0) Typ
.043 x .079
3
(18.0)
.709
(4.7) Typ
.185
25°
(2.36)
.093
(3.18)
.125
(13.7)
.539
Snap-in Frame • Solder Lug
(2.0) Typ
.079
(0.5)
.020
(9.4)
.371
(7.9)
.311
(4.5)
.177
Double Pole
(2.8)
.110
Circuit Mark
This Side
(4.8)
.189
(1.1) x (2.0) Typ
.043 x .079
6
(18.0)
.709
Accessories
Supplement
(0.5)
.020
(7.1)
.279
M2012TJW01-GC
Indicators
Touch
Tilt
(0.8) Typ
.031
(11.43)
.450
(12.2)
.480
(13.0)
.512
2
1
(4.7) Typ
.185
25°
(0.8) Typ
.031
(2.36)
.093
(11.43)
.450
(12.2)
.480
(3.18)
.125
(13.7)
.539
M2022TJW01-GC
B70
www.nkk.com
(0.5)
.020
(7.1)
.279
(9.4)
.371
(4.5)
.177
(0.5)
.020
3
5
2
4
1
(12.7)
.500
(13.0)
.512
(2.0) Typ
.079
Series M
Toggles
Snap-In Mount Miniature Rockers
TYPICAL SWITCH DIMENSIONS
(4.8)
.189
1
(0.8) Typ
.031
(4.3)
.169
(2.2)
.087
(6.4)
.252
(4.01)
.158
(9.4)
.371
Double Pole
(4.9)
.193
(30.2)
1.190
(2.5)
.098
(0.61) Sq
.024
Circuit Mark (1.1) x (2.0) Typ
This Side
.043 x .079
(13.5)
.531
(12.0)
.472
(4.7) Typ
.185
25°
(0.8) Typ
.031
(11.43)
.450
(11.8)
.465
(15.6)
.614
(4.3)
.169
(2.2)
.087
(6.4)
.252
(4.01)
.158
(5.6)
.221
(7.8)
.307
6
3
5
2
4
1
(0.5)
.020
(9.4)
.371
(4.5)
.177
Circuit Mark
This Side
(13.0)
.512
(14.0)
.551
(2.0) Typ
.079
(4.8)
.189
(12.7)
.500
Single Pole
(10.0)
.394
M2012TJW01-FC-1A
Snap-in Frame • AT208 Bezel • Solder Lug
(15.3) Min
.602
(19.0)
.748
1
Keylocks
(5.08) Dia
.200
4
(13.0)
.512
(14.0)
.551
(12.7)
.500
(7.9)
.311
(4.5)
.177
2
(2.0) Typ
.079
(2.0)
.079
(0.5)
.020
5
Rotaries
(11.43)
.450
(11.8)
.465
(15.6)
.614
(13.0)
.512
(14.0)
.551
2
Pushbuttons
(4.7) Typ
.185
25°
M2022TJW01-FC-2A-C
Snap-in Frame • AT212 Bezel • Solder Lug
(1.1) x (2.0) Typ
.043 x .079
Tactiles
(12.0)
.472
3
(8.0)
.315
(12.0)
.472
(4.7) Typ
.185
25°
(13.0)
.512
(14.0)
.551
2
(0.8) Typ
.031
1
(4.01)
.158
(9.4)
.371
(4.5)
.177
(0.5)
.020
Double Pole
(10.0)
.394
(5.6)
.221
(7.8)
.307
(8.0)
.315
(12.0)
.472
Circuit Mark
This Side
(2.0)
.079
(7.9)
.311
M2012TJW01-FC-3A-CF
Snap-in Frame • AT213 Bezel • Solder Lug
(1.1) x (2.0) Typ
.043 x .079
(4.7) Typ
.185
25°
(0.8) Typ
.031
6
3
5
2
4
1
(13.0)
.512
Indicators
(4.3)
.169
(2.2)
.087
(6.4)
.252
(14.0)
.551
Accessories
(11.43)
.450
(11.8)
.465
(21.5) Sq
.846
Tilt
(3.0) Dia Typ
.118
(5.0) Typ
.197
(2.0)
.079
(11.43)
.450
(11.8)
.465
(21.5) Sq
.846
(4.01)
.158
(4.3)
.169
(2.2)
.087
(6.4)
.252
(0.5)
.020
(9.4)
.371
(4.8)
.189
(12.7)
.500
(4.5)
.177
(2.0) Typ
.079
M2022TJW01-FC-4A-CF
www.nkk.com
Touch
(21.5)
.846
B
3
6
3
Programmable Illuminated PB
Circuit Mark
This Side
Rockers
Snap-in Frame • AT2107 Bezel • Solder Lug
(1.1) x (2.0) Typ
.043 x .079
Slides
Single & Double Pole
(5.6)
.221
B71
Supplement