Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M Miniature Rockers General Specifications B Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level (gold over silver): Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: 10 milliohms maximum for silver; 20 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum for silver; 50,000 operations minimum for gold; 50,000 operations minimum for silver at 3A @ 125V AC 25° Materials & Finishes Actuator Clip & Mounting Frame: Body Frame: Case: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Stainless Steel Stainless steel Diallyl phthalate resin (UL94V–0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; or copper or brass with gold plating Operating Temp Range: Humidity: Vibration: Shock: Processing Soldering: Cleaning: –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Actuator must be in OFF (center) position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V–0 for case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” before first dash in part number to order UL recognized switch. All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add “/C” before first dash in part number to order CSA certified switch. All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. Supplement Accessories Indicators Touch Tilt Tactiles Environmental Data B62 www.nkk.com Distinctive Characteristics B Pushbuttons Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. Rockers Toggles Series M Miniature Rockers Programmable Illuminated PB High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. The molded diallyl phthalate case has a UL 94V-0 flammability rating. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Keylocks Prominent external insulating barriers increase insulation resistance and dielectric strength. Slides Rotaries Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and internal guide does not allow transmission of diagonal force on rocker to reach contact mechanism. Snap-in Mount Page B64 Flat Frame Mount www.nkk.com Page B83 B63 Supplement Accessories Bracket PC Mount Page B72 Indicators Actual Size Touch Tilt Tactiles Clinching of the frame to the case well above the base and terminals provides 1,500V dielectric strength. Series M TYPICAL SWITCH ORDERING EXAMPLE 1 2 TN W 01 Poles C B Rockers & Paddles Mounting Frames .504” (12.8mm) Wide Flat Frame Contact Materials & Ratings Circuits 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 (ON) ON (ON) *7 ON ON (ON) W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max E .365” (9.27mm) Wide Paddle F .450” (11.43mm) Wide Rocker G .450” (11.43mm) Wide Paddle Large Actuators (TY Frame) J .595” (15.11mm) Wide Rocker H .595” (15.11mm) Wide Paddle Rocker & Paddle Colors Terminals ( ) = Momentary * 3-ON circuits 01 Solder Lug* 03 .250” (6.35mm) Straight PC IMPORTANT: Switches are supplied without UL & CSA marking unless specified. UL & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on General Specifications page. Programmable Illuminated PB 4 4PDT DP3T TY * Wire harness & cable assemblies offered only in Americas Keylocks 3PDT .365” (9.27mm) Wide Rocker Rotaries 3 D A Black B White C Red E Yellow F Green G Blue H Gray Slides TN Tactiles DPDT SP3T Small Actuators (TN Frame) Tilt 2 .272” (6.9mm) Wide Flat Frame Touch SPDT DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2012TNW01-DC Accessories Red .365” (9.27mm) Wide Rocker .272” (6.9mm) Wide Flat Frame SPDT ON-NONE-ON Circuit Silver Contacts with 6-Amp Rating Solder Lug Terminals www.nkk.com Supplement 1 D Pushbuttons M20 Rockers Toggles Flat Frame Mount Miniature Rockers B83 Series M Toggles Flat Frame Mount Miniature Rockers POLES & CIRCUITS Rocker Position ) = Momentary B Center Up M2012 M2013 M2015 M2018 M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2022 M2023 M2025 M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2032 M2033 M2035 M2038 M2039 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) M2042 M2043 M2045 M2048 M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) Model SP DP 3P 4P Connected Terminals Down Pole Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers ( Down Center Throw & Schematics Up Note: Terminal numbers are not actually on the switch. SPDT 2-3 OPEN 2 (COM) 2-1 3 1 DPDT 2-3 5-6 OPEN 2 2-1 5-4 (COM) 3 1 5 6 4 3PDT 2-3 5-6 8-9 2-1 5-4 8-7 OPEN 2 3 5 1 (COM) 6 4 8 9 7 8 11 4PDT 2-3 5-6 8-9 11-12 2-1 5-4 8-7 11-10 OPEN 5 2 3 1 (COM) 9 4 6 7 12 10 For 3 Throw (3-On) Tilt Tactiles Connected Terminals & Schematics Pole SP Model M2024 M2026 M2027 Down Center ON (ON) ON ON ON ON Up ON (ON) (ON) Touch Indicators Accessories Supplement M2044 M2046 M2047 ON (ON) ON ON ON ON External Connection 2 (in) 5 3 4 (out) 6 (out) External Connection 2 (in) 5 ON (ON) (ON) 3 5 2 4 1 (out) External Connection 2 (in) 5 External Connection 2 (in) 5 1 (out) 2-1 5-4 External Connection 8 (in) 11 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 2-3 5-4 8-9 11-10 2-1 5-4 8-7 11-10 www.nkk.com (out) External Conn Common (in) External connection must be made during field installation. (out) External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) Common (in) 3 4 (out) 6 (out) 1 (out) 3 4 (out) 6 (out) The DP3T model utilizes a four pole base. (out) 6 Up 2-3 5-4 External Connection 8 (in) 11 2-3 5-6 8-9 11-12 The SP3T model utilizes a double pole base. External Conn 1 (out) 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) B84 External Connection 2 (in) 5 2-3 5-6 External connection must be made during field installation. Center 1 (out) DP Down (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) Series M MOUNTING FRAMES (6.9) .272 B Pushbuttons (3.5) .138 (29.5) (23.8) 1.161 .937 (0.6) .024 Programmable Illuminated PB Mounting hardware kit HK-1, as shown on the following page, must be ordered separately. (2.4) Dia Typ .094 Small Actuators & Panel Cutouts for TN Frame (actuator details on the following pages) AT4149 AT4150 AT4151 (17.8) .701 (23.8) .937 (10.1) .398 TY (12.7) .500 (23.8) .937 (2.6) Dia Typ .102 (12.4) .490 (2.6) Dia Typ .102 Large Actuators & Panel Cutout for TY Frame (actuator details on the following pages) .504” (12.8mm) Wide Flat Frame AT4157 Tactiles AT4156 Slides AT4148 Keylocks .272” (6.9mm) Wide Flat Frame Rotaries TN Rockers Toggles Flat Frame Mount Miniature Rockers Touch Tilt Mounting hardware kit HK-2, as shown on the following page, must be ordered separately. (3.2) Dia Typ .126 www.nkk.com (3.5) Dia Typ .138 Supplement (16.0) .630 Accessories (28.5) 1.122 (34.9) 1.374 (41.3) (34.9) 1.626 1.374 (0.6) .024 Indicators (12.8) .504 (3.5) .138 B85 Series M Toggles Flat Frame Mount Miniature Rockers MOUNTING FRAMES (CONTINUED) Subpanel Mounting B Pushbuttons Rockers Face Panel Mounting Programmable Illuminated PB S TANDOFF LE NGTH Flat frame devices may also be mounted to the face panel. Standoffs are used to recess the actuator and achieve an attractive front panel appearance. These devices are especially designed for subpanel mounting. When installed on a mounting plate behind the panel, hardware is completely concealed and the front panel retains a clean, attractive appearance. Optional Snap-in Panel Frames Optional Hardware Kits for Subpanel or Face Panel Mounting Panel Thickness Frame Standoff Length Further details are shown in the previous bracketed PC mount subsection. Hardware Kit Number TN Frame .125” (3.175mm) .233” (5.918mm) ATHK-1 TY Frame .125” (3.175mm) .312” (7.925mm) ATHK-2 Keylocks Hardware kits include: 2 stainless steel screws, 2 hex nuts, 2 lockwashers, & 2 standoffs AT064-1 AT064-2 AT065-1 AT065-2 W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Slides Rotaries CONTACT MATERIALS & RATINGS Note: See Supplement section to find complete explanation of operating range. Tactiles A Power Level or Logic Level Gold over Silver 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. Tilt TERMINALS Touch 01 Solder Lug (4.0) .157 Epoxy Seal (2.0) .079 Indicators (2.0) (1.1) .079 .043 Thk = (0.8) .031 03 .250” (6.35mm) Straight PC (4.8) .189 Accessories 3 2 Epoxy Seal (6.35) (4.8) .250 .189 Supplement (1.17) .046 Thk = (0.8) .031 B86 (4.7) Typ .185 1 3 6 2 5 1 4 (1.8) Dia Typ .073 Single Pole (4.7) Typ .185 (1.8) Dia Typ .073 Double Pole www.nkk.com 3 6 9 2 5 8 1 4 7 (4.8) Typ .189 (4.7) Typ .185 (1.8) Dia Typ .073 Three Pole 3 6 9 12 2 5 8 11 1 4 7 10 (4.8) Typ .189 (4.7) Typ .185 (1.8) Dia Typ .073 Four Pole Series M Toggles Flat Frame Mount Miniature Rockers ROCKERS & PADDLES AT4148 .365” (9.27mm) Wide Rocker AT4149 .365” (9.27mm) Wide Paddle E (2.13) .084 (9.27) .365 (16.87) .664 (13.49) .531 (3.96) .156 (18.8) .740 (3.5) .138 AT4150 .450” (11.43mm) Wide Rocker AT4151 .450” (11.43mm) Wide Paddle G Material: Polyamide Finish: Matte (2.36) .093 (11.43) .450 (11.8) .465 (9.19) .362 (3.18) .125 (16.36) .644 (7.7) .303 (8.1) (6.3) .319 .248 Rotaries Material: Polyamide Finish: Matte (11.43) .450 (3.5) .138 (16.8) .661 Keylocks (7.9) (6.15) .311 .242 F (8.43) R .332 (8.8) .346 (3.5) .138 (5.84) R .230 Slides (9.27) .365 Pushbuttons Material: Polyamide Finish: Matte Programmable Illuminated PB Material: Polyamide Finish: Matte B (3.5) .138 (11.8) .465 Tactiles D For TY Frame AT4156 .595” (15.11mm) Wide Rocker H (2.36) .093 (14.33) .564 (29.82) 1.174 (23.01) .906 (11.0) .433 (8.4) (6.5) .331 .256 (7.3) .287 (3.5) .138 A (13.5) R .531 Black B White (26.8) 1.055 (15.11) .595 C Red E Yellow www.nkk.com F Green G Blue Accessories (26.78) 1.054 Indicators (4.75) .187 (15.11) .595 Cap Colors Available: Tilt Material: Polyamide Finish: Matte Touch Material: Polyamide Finish: Matte AT4157 .595” (15.11mm) Wide Paddle (3.5) .138 H Supplement J Rockers For TN Frame Gray B87 Series M Toggles Flat Frame Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Rockers TN Frame • Solder Lug Single Pole (2.4) Dia Typ .094 (12.3) .484 B (3.5) .138 Circuit Mark This Side (1.1) x (2.0) Typ .043 x. 079 3 TN Frame • Solder Lug (0.6) .024 (10.3) .406 1 (0.5) .020 (2.0) .079 (7.9) .311 (4.5) .177 Double Pole (2.4) Dia Typ .094 (12.3) .484 (2.0) Typ .079 (1.1) x (2.0) Typ .043 x. 079 (3.5) .138 Circuit Mark This Side Rotaries (29.5) 1.161 (23.8) .937 (4.7) Typ .185 25° (0.8) Typ .031 (7.9) .311 (9.65) .380 (6.9) .272 (9.27) .365 M2022TNW01-DC TN Frame • Solder Lug (0.6) .024 (10.3) .406 (4.5) .177 6 3 5 2 4 1 (0.5) .020 (13.0) .512 (4.8) .189 (12.7) .500 Three Pole (12.3) .484 (2.4) Dia Typ .094 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 (2.0) Typ .079 Circuit Mark This Side Tactiles Slides (7.9) .311 (9.65) .380 (13.0) .512 2 (0.8) Typ .031 (6.9) .272 (9.27) .365 M2012TNW01-DC (4.7) Typ .185 25° (29.5) 1.161 Keylocks Programmable Illuminated PB Pushbuttons (23.8) .937 (23.8) .937 (4.7) Typ .185 25° (29.5) 1.161 6 3 8 5 2 7 4 1 (13.0) .512 Touch Tilt (0.8) Typ .031 9 (7.9) .311 (9.65) .380 (6.9) .272 (9.27) .365 M2032TNW01-DC TN Frame • Solder Lug (0.5) .020 (4.8) Typ .189 (4.5) .177 (17.5) .689 Four Pole (12.3) .484 Indicators (2.4) Dia Typ .094 (1.1) x (2.0) Typ .043 x .079 (3.5) .138 (2.0) Typ .079 Circuit Mark This Side (23.8) .937 (29.5) 1.161 Accessories Supplement (0.6) .024 (12.4) .488 M2042TNW01-DC B88 (4.7) Typ .185 25° (0.8) Typ .031 (6.9) .272 (7.9) .311 (9.27) .365 (9.65) .380 www.nkk.com 9 6 3 11 8 5 2 10 7 4 1 (0.5) .020 (0.6) .024 (12.4) .488 12 (4.5) .177 (13.0) .512 (4.8) Typ .189 (22.3) .878 Series M Toggles Flat Frame Mount Miniature Rockers TYPICAL SWITCH DIMENSIONS Double Pole B 3 (4.7) Typ .185 25° 2 (0.8) Typ .031 (12.8) .504 (15.11) .595 (8.4) .331 (10.0) .394 (0.6) .024 (10.0) .394 (4.5) .177 (13.0) .512 6 3 5 2 4 1 1 (0.5) .020 (7.9) .311 (2.0) .079 (4.8) .189 (13.0) .512 (2.0) Typ .079 Double pole has barrier between terminals. Three Pole (3.2) Dia Typ .126 (14.5) .571 TY Frame • Solder Lug (2.0) Typ .079 (1.1) x (2.0) Typ .043 x .079 (3.5) .138 M2012TYW01-JC Rotaries Programmable Illuminated PB (41.3) 1.626 (34.9) 1.374 Pushbuttons Circuit Mark This Side Circuit Mark This Side 25° (0.8) Typ .031 (8.4) .331 (12.8) .504 (15.11) .595 (10.0) .394 (12.1) .476 3 8 5 2 7 4 1 (13.0) .512 (0.5) .020 (4.8) Typ .189 (4.5) .177 (17.5) .689 M2032TYW01-JC Four Pole (3.2) Dia Typ .126 (14.5) .571 TY Frame • Solder Lug (2.0) Typ .079 (3.5) .138 (1.1) x (2.0) Typ .043 x .079 Touch (0.6) .024 6 Slides (41.3) 1.626 (4.7) Typ .185 Tactiles 9 (34.9) 1.374 25° (0.8) Typ .031 (12.8) .504 (15.11) .595 (8.4) .331 (10.0) .394 (0.6) .024 (12.1) .476 6 3 11 8 5 2 10 7 4 1 (0.5) .020 (22.3) .878 (4.5) .177 (13.0) .512 Accessories (41.3) 1.626 9 (4.8) Typ .189 Supplement 12 (4.7) Typ .185 Indicators Circuit Mark This Side (34.9) 1.374 Rockers Single Pole (1.1) x (2.0) Typ .043 x .079 (3.5) .138 Tilt (14.5) .571 (3.2) Dia Typ .126 TY Frame • Solder Lug Keylocks M2042TYW01-JC www.nkk.com B89 Series M Toggles Flat Frame Mount Miniature Rockers LEGENDS B Suggested Printable Area for Caps Pushbuttons Rockers NKK Switches can provide custom legends for caps. Contact factory for more information. AT4148 AT4150 ON ON OF F F OF OF Programmable Illuminated PB ON AT4156 F Keylocks (0.38) Typ .015 (6.9) Typ .272 Rotaries (0.76) Typ .030 (5.76) Typ .227 (7.75) .305 (9.27) .365 (0.76) Typ .030 (0.38) Typ .015 (4.5) Typ .177 (0.76) Typ .030 (9.91) .390 (11.43) .450 (0.76) Typ .030 (3.36) Typ .132 Slides Recommended Print Method: Pad Print Tactiles (10.03) Typ .395 (11.18) Typ .440 Shaded areas are printable areas. Supplement Accessories Indicators Touch Tilt Epoxy based ink is recommended. B90 (0.38) Typ .015 www.nkk.com (0.76) Typ .030 (13.59) .535 (15.11) .595 (0.76) Typ .030