Photo IC for optical link L11354-01 Transmitter Receiver photo IC photo IC L11354-01 S11355-03 Transmitter/ receiver photo IC P11379-04AT S11355-03 P11379-04AT For 150 Mbps optical link This photo IC is capable of data communication at a data rate of 150 Mbps through a plastic optical fiber (POF). Its transmitter is composed of a 650 nm RC (resonant cavity) type LED, which is suitable for POF communications, and a driver circuit that supports an LVDS interface. The transmitter has a built-in temperature compensation function that adjusts for the reduction in the light emission power caused by the high temperature emitted from the RC type LED. This function makes light emission with stable power possible over a wide temperature range. The receiver is composed of a PIN photodiode and signal processing circuit. The adoption of a full differential structure using a dummy photodiode eliminates the effects of external noise, achieving high sensitivity. In addition, the photo IC has a sleep function that suppresses power consumption by switching to standby mode when there is no input. This product features high quality and high reliability, allowing it to be installed even in automobiles for in-vehicle networking. It is already used as an optical fiber transceiver (FOT) for a MOST network, which is a type of in-vehicle multimedia network. POFs with ferrule are also available. Features Applications Communication speed up to 150 Mbps Data transmission in harsh, noisy environments, such as in FA and OA. Sidelooker type and SMD type are available. High-speed, short-distance data transmissio 3.3 V power supply operation Only for vehicle networks (MOST) Wide operating temperature: -40 to +95 °C Suitable for reflow soldering MOST compliant products Specifications of these products are subject to change without prior notice to keep up with changes in the MOST standard. Sleep mode function Absolute maximum ratings Parameter L11354-01 P11379-04AT (Transmitter) Supply voltage S11355-03 P11379-04AT (Receiver) Input voltage L11354-01 Power S11355-03 dissipation P11379-04AT Operating temperature Storage temperature Reflow soldering conditions*1 Symbol Condition Unit Value Vcc_TX -0.5 to +7.0 V Ta=-40 to +95 °C Vcc_RX -0.5 to +4.6 Vi Ta=-40 to +95 °C P Ta=-40 to +95 °C Topr Tstg Tsol -0.5 to Vcc+0.5 350 320 1250 -40 to +95 -40 to +110 Peak temperature 260 °C max., 3 times (see page 12) V mW °C °C - *1: JEDEC level 2a Note: Exceeding the absolute maximum ratings even momentarily may cause a drop in product quality. Always be sure to use the product within the absolute maximum ratings. Recommended operating conditions Parameter Supply voltage Data rate Symbol Vcc fD Condition DCA coding Min. 3.135 - www.hamamatsu.com Typ. 3.3 - Max. 3.465 150 Unit V Mbps 1 Photo IC for optical link L11354-01, S11355-03, P11379-04AT L11354-01, P11379-04AT (Transmitter) Electrical and optical characterisitics*2 (Ta=-40 to +95 °C, Vcc=3.135 to 3.465, unless otherwise noted*3) Parameter Current consumption Peak emission wavelength Spectral width (RMS) Fiber coupled optical output 1 Fiber coupled optical output 2 Extinction ratio Rise time Fall time Transfer jitter (RMS) Overshoot Undershoot Symbol Condition Min. Typ. Max. Unit 40 mA Icc *4 635 650 675 nm λC2 17 nm σλ2 Po1 -7 -1.5 dBm CTRL_TX=Low,*5 *6 -50 dBm POFF2 re 10 dB tr 0.5 UI 20 to 80%,*4 *5 tf 0.5 UI 80 to 20%,*4 *5 112 ps Jtr2 *4 *5 rpos See “ Overshoot” table. *5 rnos See “ Undershoot” table. *5 0.8 VinRL *7 V Input voltage level “/RST” 2 VinRH *7 0.8 VinCL Input voltage level “CTRL_TX” V 2 VinCH -0.1 IinRL /RST=Low Input current “/RST” μA 50 IinRH /RST=High -0.1 IinCL CTRL_TX=Low Input current “CTRL_TX” μA 50 IinCH CTRL_TX=High -0.1 IinTXL TXN, TXP=Low Input current “TXN” “TXP” μA 0.1 IinTXH TXN, TXP=High During transmission 12 73.743 MHz FON1 Frequency range During non-transmission FOFF1 0 10 kHz *8 * 9 100 μs tON2 Valid MOST data (SP2) time 2 μs tOFF2 *8 *10 Eye mask See “ Eye mask” table. A2 to F2 *2: Electrical interface conforms to LVDS standards except common mode input voltage. *3: Connect a bypass capacitor (0.1 μF) between Vcc and GND at a position within 3 mm from the leads. Also connect a 10 μF capacitor near the photo IC. L11354-01: The center of the optical fiber is aligned with the center of the package lens. The distance between the fiber end and the lens top is 0.1 mm. *4: Input signal rate 150 Mbps (DCA coding) *5: Input signal Parameter Symbol Min. Typ. Max. Unit Differential input voltage Vid 200 1272 mV Common mode input voltage VCM 0.05 Vcctx - 1.2 V Total jitter tTJtp1 0.15 UI Transfer jitter (RMS) Jtr1 50 ps *6: Average value, fiber core diameter ϕ1 mm, POF, NA=0.5, 1 m (made by Mitsubishi Rayon) *7: /RST signal Parameter Symbol Min. Valid supply voltage range 1 VVALID Logic switching threshold 2.97 VT 0→1 1 tD+ Logic delay time 1→0 0 tDTiming chart” for the /RST signal timing chart. Note: See “ *8: See “ Timing chart”. *9: Delay time for light output to turn on *10: Delay time for light output to turn off Max. 3.465 100 Unit V V ms μs 2 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Overshoot Parameter AO BO CO DO EO FO GO HO JO KO Amplitude*11 -0.200 -0.200 0.500 0.800 0.800 0.200 0.200 0.500 1.400 1.400 Time (UI) -0.630 0.100 0.100 0.350 1.370 -0.630 -0.350 -0.100 -0.100 1.370 Overshoot Keep out area JO KO b1=1 EO DO HO b0 + b1 2 CO GO FO Keep out area b0=0 BO AO KPICB0153EA T=0 *11: On the basis of b0=0 and b1=1 Undershoot Parameter AU BU CU DU EU FU GU HU JU KU LU MU NU PU RU SU TU Amplitude*12 0.800 0.800 0.850 0.850 0.800 0.800 0.500 -0.200 -0.200 1.400 1.400 1.340 1.150 1.150 0.500 0.200 0.200 Time (UI)*13 -0.630 - x -0.530 - x -0.530 - x -0.430 -0.430 -0.350 -0.100 -0.100 1.370 -0.630 - x -0.530 - x -0.530 - x -0.220 - x 0.100 0.100 0.350 1.370 Undershoot LU KU NU MU b1=1 PU CU AU DU B U EU F U b0 + b1 2 Keep out area RU GU SU TU b0=0 JU HU Keep out area T=0 KPICB0154EB *12: On the basis of b0=0 and b1=1 *13: The positions of Au, Bu, Cu, Ku, Lu and Mu on the time axis depend on the MOST data pulse width (2 to 6). x=MOST data pulse width - 2 For 2UI: x=0, For 6UI: x=4 Eye mask Parameter Amplitude A2 B2 C2 D2 E2 F2 0.5 × (b1 + b0) 0.8 × (b1 - b0)+b0 0.8 × (b1 - b0)+b0 0.5 × (b1 + b0) 0.2 × (b1 - b0)+b0 0.2 × (b1 - b0)+b0 Time (UI) 0.150 0.400 0.600 0.850 0.600 0.400 Eye mask B2 A2 C2 Keep out area F2 D2 E2 KPICB0155EA 3 Photo IC for optical link L11354-01, S11355-03, P11379-04AT S11355-03, P11379-04AT (Receiver) Electrical and optical characterisitics*14 (Ta=-40 to +95 °C, Vcc=3.135 to 3.465, unless otherwise noted*15) Parameter Peak sensitivity wavelength Current consumption (operation mode) Current consumption (sleeping mode) High level output voltage STATUS Low level output voltage Operation to sleeping mode transition receivable level Transfer jitter (RMS) Error rate Valid MOST data (input signal) frequency Invalid MOST data frequency Time from input signal start to operation mode Time from input signal start to STATUS ON Time from STATUS ON to LVDS output stabilization Time from input signal stop to sleeping mode LVDS output hold time Time from input signal stop to STATUS OFF Eye mask Symbol λp Icco Iccs Vmh Vml POFF3 Condition *16 Dark state Imh=20 μA,*17 Iml=0.2 mA,*17 *16 *18 *19 Min. 2.5 - Typ. 800 - Max. 40 30 0.5 Unit nm mA μA V V - - -35 dBm 230 ps Jtr4 Pe *16 *19 *20 *21 *22 10-9 12 73.743 MHz FON3 0 10 kHz FOFF3 *23 10 ms tON4 *23 200 1000 tSTATF μs 100 tLVDSV4 *23 μs *23 1 tOFF4 ms 1 tLVDSH4 *23 μs *23 2 tSTATR μs See “ Eye mask” table. A4 to F4 *14: Electrical interface conforms to LVDS standards except differential output amplitude level *15: Connect a bypass capacitor (0.1 μF) between Vcc and GND at a position within 3 mm from the leads. Also connect a 10 μF capacitor near the photo IC. *16: Input signal Parameter Symbol Min. Typ. Max. Unit S11355-01 -23.5 -2 Optical data that allows Valid Popt3 dBm MOST data (SP4) to be obtained P11379-04AT -21.5 -2 Rise time trtp3 2 ns Fall time tftp3 2 ns Total jitter tTJtp3 600 ps Extinction ratio re 10 dB *17: Changes to operation mode when input light enters the receiver section. When STATUS output is low, the photo IC is in operation mode. When STATUS output is high, the photo IC is in sleeping mode. *18: Input light is specified as the average power at the fiber end. The optical fiber used is a POF (NA=0.5). *19: The center of the optical fiber is aligned with the center of the package lens. The distance between the fiber end and the lens top is 0.1 mm. *20: RL=100 kΩ, CL=3 pF (including parasitic capacitance such as probe, connector and circuit board) *21: A standard transmitter specified by HAMAMATSU is used to input light. *22: Optical input signal rate=150 Mbps (DCA coding) Timing chart”. *23: See “ Eye mask Parameter A4 B4 C4 D4 E4 F4 G4 H4 Amplitude (mV) 0 148 148 0 -148 -148 636 -636 Time (UI) 0.275 0.425 0.575 0.725 0.575 0.425 - Eye mask G4 Keep out area B4 A4 Keep out area F4 H4 C4 D4 E4 Keep out area KPICB0156EA 4 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Timing chart L11354-01, P11379-04AT (Transmitter) Reset: ON Signal: ON VCCTXOR max. VCCTXOR min. VCCTXOR max. VCCTXOR min. VT EOC power 0V 0V /RST VT EOC power tD+ /RST SP1 Disabled SP1 Disabled Valid MOST data b1 Valid MOST data POFF2 SP2 tD+ Valid MOST data b1 Valid MOST data LVDS 0 POFF2 SP2 tON2 tON2 Signal: OFF Reset: OFF EOC power EOC power VT VT 0V 0V /RST /RST SP1 SP2 tD- Valid MOST data Valid MOST data POFF2 tOFF2 Disabled SP1 Valid MOST data LVDS 0 SP2 Valid MOST data b0 Disabled b0 POFF2 tOFF2 KPICC0176EA KPICC0176EA S11355-03, P11379-04AT (Receiver) tON4 tSTATF tOFF4 tLVDSV4 tLVDSH tSTATR b1 Valid MOST data PON3 b0 SP3 POFF3 1 STATUS SP4 0 Disabled Enabled Valid MOST data LVDS 0 Disabled KPICC0181EA 5 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Block diagram L11354-01, P11379-04AT (Transmitter) VCC_TX Current driver TXP RC type LED LVDS receiver TXN Peak current driver Signal detection /RST Temperature monitor Current source Ctrl_TX GND_TX KPICC0177EB S11355-03, P11379-04AT (Receiver) VCC_RX VCC_RX2 PD GND_RX Preamp Sleep level comparator Comparator Main amplifier Bias SD judge LVDSOUT RXP RXN STATUS KPICC0178EA 6 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Connection example L11354-01 + C2 C1 L1 + C3 VCC_TX 3.3 V Ctrl_TX Ctrl_TX TXP TXP L11354-01 GND_TX R1 TXN /RST TXN /RST GND *Bold line: 50 Ω impedance matching KPICC0179EA Symbol R1 L1 C1 C2 C3 Part Resistor Inductance Capacitor Capacitor Capacitor Constant 100 Ω 0.1 μH 0.1 μF 10 μF 10 μF S11355-03 C1 + C2 L1 + C3 VCC_RX2 3.3 V RXP RXP R1 S11355-03 RXN GND_RX STATUS RXN STATUS GND *Bold line: 50 Ω impedance matching KPICC0180EC Symbol R1 L1 C1 C2 C3 Part Resistor Inductance Capacitor Capacitor Capacitor Constant 100 Ω 0.1 μH 0.1 μF 10 μF 10 μF 7 Photo IC for optical link L11354-01, S11355-03, P11379-04AT P11379-04AT RXP R1 RXP + L1 C2 Vcc_RX2 C3 RXN RXN GND_RX2 + C1 3.3 V Vcc_RX1 C4 STATUS STATUS TX_Ctrl TX_Ctrl /RST /RST GND_TX2 TXP TXP Vcc_TX1 TXN GND_TX1 R2 GND_RX1 GND Vcc_TX2 C7 + L2 C6 + C5 3.3 V C8 GND TXN *Bold line: 50 Ω impedance matching KPICC0187EA Symbol R1 L1 C1 C2 C3 C4 Transmitter Part Resistor Inductance Capacitor Capacitor Capacitor Capacitor Constant 100 Ω 0.1 μH 10 μF 10 μF 0.1 μF 0.1 μF Symbol R2 L2 C5 C6 C7 C8 Receiver Part Resistor Inductance Capacitor Capacitor Capacitor Capacitor Constant 100 Ω 0.1 μH 10 μF 10 μF 0.1 μF 0.1 μF Eye diagram Optical output waveform of L11354-01, P11379-04AT (Transmitter) Output waveform of S11355-03, P11379-04AT (Receiver) 8 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Dimensional outlines (unit: mm) L11354-01 S11355-03 8.98 ± 0.2 (including burr) 2.72 7.2 ± 0.2 (including burr) 1.57 5.92 2.94 0.6 1.5 2.03 ± 0.05 Photosensitive area 2.45 3.7 ± 0.05 5.1 1.07 (7 ×) 0.5 ± 0.05 ϕ2.0 depth 0.15 max. 0.25 ± 0.05 1.27 1.27 1.27 1.27 1.27 1.27 (Specified at lead root) ϕ0.66 ϕ1.8 ϕ2.92 (2 ×) 5° /RST (/RST) TXN TXP GND_TX Vcc_TX Ctrl_TX ϕ1.24 (Specified at lead root) 5.9 ± 0.2 (including burr) 1.27 1.27 1.27 1.27 1.27 1.27 ϕ0.2 (7 ×) 0.5 ± 0.05 5.9 ± 0.2 (including burr) 1.07 5.1 A' 0.97 (2 ×)ϕ0.8 ± 0.05 5.92 2.03 ± 0.05 Emission area A 2.45 3.7 ± 0.05 2.94 (2 ×) 10° (2 ×)ϕ0.8 ± 0.05 2.85 7.2 ± 0.2 (including burr) (2 ×) 10° 8.98 ± 0.2 (including burr) 0.23 +0.05 0.05 -0.03 A-A' cross section STATUS Vcc_RX1 GND_RX RXN RXP (Vcc_RX2) Vcc_RX2 Tolerance unless otherwise noted: ±0.1, ±2° R0.3 max. Lead material: Cu alloy with Ag plating Shaded area indicates burr. Standard packing state: stick (50 pcs/stick) KPICA0079EC KPICA0079EC 9 Photo IC for optical link L11354-01, S11355-03, P11379-04AT P11379-04AT 0.56 ± 0.3 15.4 ± 0.3 0.56 ± 0.3 7.5 ± 0.2 10.3 ± 0.3 0.4 ± 0.1 Index mark 6 ± 0.03 Pin connections Pin no. RXP 1 OEC RXN 2 OEC Vcc_RX1 3 OEC GND_RX1 4 OEC STATUS 5 OEC SHIELD 6 SHIELD 7 TX_Ctrl 8 EOC Vcc_TX1 9 EOC GND_TX1 10 EOC TXP 11 EOC TXN 12 EOC OEC: receiver, EOC: transmitter 0.1 to 0.3 9.5 ± 0.3 1.27 ± 0.1 Tolerance unless otherwise noted: ±0.1, ±2° R0.3 max. Lead material: Cu alloy with Ni/Pd/Au plating Pin no. 13 14 15 16 17 18 19 20 21 22 23 24 Pin connections /RST EOC (N/C) EOC GND_TX2 EOC Vcc_TX2 EOC GP2 (not used) EOC SHIELD SHIELD (Vcc_RX2) OEC GND_RX2 OEC Vcc_RX2 OEC (N/C) OEC (GND_RX2) OEC KPICA0086EC KPICA0086EC 1.3 9.6 1.3 Recommended land pattern (unit: mm, P11379-04AT) (24×) 0.8 (11×) 1.27 KPICC0189EB 10 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Standard packing specifications Reel (conforms to JEITA ET-7200) Dimensions 380 mm Hab diameter 80 mm Tape width 32 mm Material PS Electrostatic characteristics Conductive 4 ± 0.1 14.2 ± 0.1 15.7 ± 0.1 22 ± 0.3 16 ± 0.1 0.38 ± 0.05 32 ± 0.3 2 ± 0.1 Index mark 1.75 ± 0.1 Embossed tape (unit: mm, material: PET) +0.1 ϕ1.5 -0 Reel feed direction 10.6 ± 0.1 5 ± 0.3 9.8 ± 0.2 KPINC0212EA Packing quantity 500 pcs/reel Packing type Reel and desiccant in moisture-proof packing (vacuum-sealed) 11 Photo IC for optical link L11354-01, S11355-03, P11379-04AT Measured example of temperature profile with our hot-air reflow oven for product testing 300 °C 260 °C max. Temperature 217 °C 200 °C 150 °C Preheat 160 s Soldering 100 s max. Time KPICB0168EB ∙ This product supports lead-free soldering. After unpacking, store it in an environment at a temperature of 30 °C or less and a humidity of 60% or less, and perform soldering within 4 weeks. ∙ The effect that the product receives during reflow soldering varies depending on the circuit board and reflow oven that are used. Before actual reflow soldering, check for any problems by tesitng out the reflow soldering methods in advance. Related information www.hamamatsu.com/sp/ssd/doc_en.html Precautions ∙ Notice ∙ Metal, Ceramic, Plastic products ∙ Surface mount type products Information described in this material is current as of September, 2014. Product specifications are subject to change without prior notice due to improvements or other reasons. This document has been carefully prepared and the information contained is believed to be accurate. In rare cases, however, there may be inaccuracies such as text errors. Before using these products, always contact us for the delivery specification sheet to check the latest specifications. Type numbers of products listed in the delivery specification sheets or supplied as samples may have a suffix "(X)" which means preliminary specifications or a suffix "(Z)" which means developmental specifications. The product warranty is valid for one year after delivery and is limited to product repair or replacement for defects discovered and reported to us within that one year period. However, even if within the warranty period we accept absolutely no liability for any loss caused by natural disasters or improper product use. Copying or reprinting the contents described in this material in whole or in part is prohibited without our prior permission. www.hamamatsu.com HAMAMATSU PHOTONICS K.K., Solid State Division 1126-1 Ichino-cho, Higashi-ku, Hamamatsu City, 435-8558 Japan, Telephone: (81) 53-434-3311, Fax: (81) 53-434-5184 U.S.A.: Hamamatsu Corporation: 360 Foothill Road, Bridgewater, N.J. 08807, U.S.A., Telephone: (1) 908-231-0960, Fax: (1) 908-231-1218 Germany: Hamamatsu Photonics Deutschland GmbH: Arzbergerstr. 10, D-82211 Herrsching am Ammersee, Germany, Telephone: (49) 8152-375-0, Fax: (49) 8152-265-8 France: Hamamatsu Photonics France S.A.R.L.: 19, Rue du Saule Trapu, Parc du Moulin de Massy, 91882 Massy Cedex, France, Telephone: 33-(1) 69 53 71 00, Fax: 33-(1) 69 53 71 10 United Kingdom: Hamamatsu Photonics UK Limited: 2 Howard Court, 10 Tewin Road, Welwyn Garden City, Hertfordshire AL7 1BW, United Kingdom, Telephone: (44) 1707-294888, Fax: (44) 1707-325777 North Europe: Hamamatsu Photonics Norden AB: Torshamnsgatan 35 16440 Kista, Sweden, Telephone: (46) 8-509-031-00, Fax: (46) 8-509-031-01 Italy: Hamamatsu Photonics Italia S.r.l.: Strada della Moia, 1 int. 6, 20020 Arese (Milano), Italy, Telephone: (39) 02-93581733, Fax: (39) 02-93581741 China: Hamamatsu Photonics (China) Co., Ltd.: B1201, Jiaming Center, No.27 Dongsanhuan Beilu, Chaoyang District, Beijing 100020, China, Telephone: (86) 10-6586-6006, Fax: (86) 10-6586-2866 Cat. No. KPIC1079E04 Sep. 2014 DN 12