Download Specifications

Toggles
Series WB
Rockers
General Specifications
Electrical Capacity (Resistive Load)
Indicators
Touch
Tilt
Tactiles
Slides
Rotaries
Keylocks
Programmable Illuminated PB
Pushbuttons
C
Power Level:
Other Ratings
Contact Resistance: Insulation Resistance:
Dielectric Strength:
Mechanical Life:
Electrical Life:
Contact Timing:
Total Travel: Materials & Finishes
Plunger:
Bushing & Outer Case:
Inner Case:
Inner Sealing Ring:
Outer Sealing Ring:
Movable Contactor:
Movable Contacts:
Stationary Contacts:
Terminals:
Wire Lead Covers:
Environmental Data
Operating Temp Range:
Humidity: Vibration:
Shock:
Installation
Mounting Torque:
Soldering Time & Temp: tandards & Certifications
S
Flammability Standards:
Wiring Material Standards:
6A @ 125V AC & 3A @ 250V AC or 6A @ 30V DC
10 milliohms maximum for solder lug & screw terminal models
30 milliohms maximum for wire lead terminal models
200 megohms minimum @ 500V DC
1,500V AC minimum for 1 minute minimum
30,000 operations minimum
15,000 operations minimum
Break before make
Alternate Action .177” (4.5mm); Momentary Action .110” (2.8mm)
Brass with nickel plating
Fiberglass reinforced polyamide (UL94V-0 outer case)
Melamine
Silicone rubber
Natural rubber
Copper with silver plating
Silver alloy with silver plating
Silver alloy with silver plating
Brass with silver plating for screw lug models;
brass with tin plating for solder lug & wire lead models
Heat resistant polyvinyl chloride (Leads are AWG 16.)
–30°C through +70°C (–22°F through +158°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning
in 1 minute; 3 right angled directions for 2 hours
50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
1.5Nm (13 lb • in)
Manual Soldering: See Profile A in Supplement section. UL94V-0 outer case
UL AWM 1015 Recognized at Flammability VW-1;
Temperature Range –20°C ~ +105°C; Maximum Load 600V; AWG 16
CSA TEW 105 Certified at Temperature Range –20°C ~ +105° C;
Maximum Load 600V
Supplement
Accessories
Environmentally Sealed Pushbuttons
C134
www.nkk.com
Toggles
Series WB
Rockers
Distinctive Characteristics
Single unit construction of the bushing and case gives added
protection from environmental elements.
Programmable Illuminated PB
C
Pushbuttons
Environmentally Sealed Pushbuttons
Specially designed contact mechanism for breaking light welds.
Keylocks
Minimal contact bounce is achieved with specially
designed interlocked switching mechanism.
Rotaries
Outer housing of heat resistant resin meets UL 94V-0
flammability standard and provides high arc and
tracking resistance.
Tactiles
Tilt
Actual Size
Supplement
Accessories
Indicators
Touch
Wire lead models conform fully to IP67 of IEC60529 Standards
at front and behind panel (dust tight and water protected for
temporary immersion). These models are epoxy sealed at the
switch base and covered by an outer case for further protection
from dust and water (not operable under water).
Slides
Solder lug and screw terminal models meet IP67 of
IEC60529 Standards at front panel (dust tight and
water protected for temporary immersion). Behind
panel standard is IP60 (dust tight but not water protected).
www.nkk.com
C135
Series WB
Toggles
Environmentally Sealed Pushbuttons
TYPICAL SWITCH ORDERING EXAMPLE
1
Poles
C
1
2
S
Circuits
SPDT
D
Terminals
ON
ON
S
Solder Lug*
5
ON
(ON)
T
Screw Lug
( ) = Momentary
L
Wire Lead
.520”
(13.2mm) Dia.
E
.748”
(19.0mm) Dia.
Black .520” (13.2mm)
Diameter Cap
WB12S-DA
A
Black
B
White
C
Red
*D
Amber
*E
Yellow
F
Green
*G
Blue
*H
Gray
* Not available
with cap code E
SPDT
ON-ON Circuit
* Wire harness & cable assemblies offered only in Americas
Rotaries
POLES & CIRCUITS
Actuator Position ( ) = Momentary
Slides
Cap Colors
D
Solder Lug Terminals
Tactiles
A
Caps
2
DESCRIPTION FOR
TYPICAL ORDERING EXAMPLE
Keylocks
Programmable Illuminated PB
Pushbuttons
Rockers
WB
Normal
Pole
Model
SP
SP
WB12
WB15
Down
Normal
Flat
ON
ON
Connected Terminals
Throw & Schematics
Down
Note: Terminal numbers are not actually
on wire lead models.
Flat
ON
(ON)
1-1b
1-1b
1 (COM)
1-1a
1-1a
SPDT
1a
1b
Tilt
STANDARD WIRE COLOR SCHEME
Terminal Numbers & Wire Colors
Indicators
Touch
Wire leads are covered with heat resistant vinyl in accordance
to UL 1015 and CSA TEW 105 Standards for Appliance Wiring
Material (AWM).
Models
1a
1
1b
WB12L, WB15L
White
Black
Red
TYPICAL SWITCH DIMENSIONS
Solder Lug
Flatted
(0.8) Typ
.031
Supplement
Accessories
(13.2) Dia
.520
(28.8)
1.134
1
(2.4) Dia Typ
.094
M12 P1
(11.0)
.433
(15.8)
.622
(1.0)
.039
(9.6)
.378
WB15S-DA
C136
1b
www.nkk.com
(4.8)
.189
(33.0)
1.299
1a
(11.2)
.441
(12.5) Dia
.492
(4.8)
.189
(19.4)
.764
Panel Thickness
.157” (4.0mm)
Series WB
Toggles
Environmentally Sealed Pushbuttons
TYPICAL SWITCH DIMENSIONS
Screw Lug
M3.5 x 5
(11.2)
.441
(1.0)
.039
(9.6)
.378
C
(1.0)
.039
(8.3)
.327
(36.5)
1.437
Panel Thickness
.157” (4.0mm)
(19.4)
.764
WB12T-DA Wire Lead
Flatted
(30.2)
1.189
1
(11.2)
.441
(1.0)
.039
(9.6)
.378
(10.0)
.394
(200.0) +- (20.0)
7.874
(38.0)
1.496
Rotaries
(12.5) Dia
.492
1a
M12 P1
(11.0)
.433
(15.8)
.622
Keylocks
1b
(13.2) Dia
.520
Panel Thickness
.157” (4.0mm)
(20.8)
.819
Slides
WB12L-DA
CAPS & CAP COLORS
D
(12.8) Dia
.504
AT414
.520” (13.2mm) Diameter
(11.0)
.433
(14.9)
.587
Colors Available:
ABCDEFGH
Material: PBT
Cap Color
Codes:
Black
B
White
C
Red
AT412
.748” (19.0mm) Diameter
(8.0)
.315 (11.7)
.461
Colors Available:
ABCF
(13.2) Dia
.520
M3.5 P0.6
Finish: Glossy
A
E
Material: Polystyrene
D
Amber
E
Yellow
F
Green
(19.0) Dia
.748
M3.5 P0.6
Finish: Glossy
G
Blue
H
Gray
Tactiles
M12 P1
(11.0)
.433
(15.8)
.622
(12.5) Dia
.492
Tilt
(28.8)
1.134
1
1a
Touch
(6.6)
.260
Programmable Illuminated PB
1b
(13.2) Dia
.520
Pushbuttons
Rockers
Flatted
Material:
Brass with
chrome plating
(14.3)
.563
AT401P
O-ring
(12.1)
.476
Material:
Steel with
zinc/chromate
(15.8) Dia
.622
(13.8) Dia
.543
1 supplied
with each
switch
(16.0)
.630
(2.4)
.094
1 supplied
with each
switch
(0.5)
.020
(1.0)
.039
www.nkk.com
Material:
Nitrile
butadiene
rubber
1 supplied
with each
switch
(12.1) Dia
.476
(17.5) Dia
.689
Accessories
AT508
Internal Tooth Lockwasher
M12 P1
Supplement
AT503M
Hex Face Nut
Indicators
STANDARD HARDWARE
(1.5)
.059
C137
Notes
C138
www.nkk.com