™ GLASSvent Product 1620/1620 Headline SSG UT Windows Curtain Wall System ® Best-in-Class Description See Less So You Thermal Can See Performance More in a Visually Concealed Vent caption Never before has something so seamless offered so much thermal performance. GLASSvent™ UT (Ultra Thermal) Windows are visually frameless concealed vents designed to provide a ventilation option for curtain wall with high thermal performance. The extraordinary thermal performance of GLASSvent™ UT Windows exceeds the thermal standards of many high-performing framing systems. Engineered for seamless integration with the 1600UT System™1 Curtain Wall, GLASSvent™ UT Windows can also be inserted into other Kawneer captured curtain walls and front set framing systems. In addition to meeting code requirements, GLASSvent™ UT Windows are the ideal solution for architects and designers who want to provide fresh-air ventilation without sacrificing thermal performance in curtain wall or storefront applications. As with all Kawneer windows, this ultra thermal vent is made from material that will never rot, warp or buckle due to moisture and weather exposure. Performance Performance Test Standards This high-performance vent is available for integration with curtain wall and framing systems to create a complete, advanced, thermally superior solution for commercial construction. GLASSvent™ UT Windows are engineered to meet or exceed the minimum requirements for the architectural window performance class, including life-cycle testing – the highest level attainable. GLASSvent™ UT Windows have been rigorously tested to both AAMA and CSA standards for air, water, structural, thermal and condensation performance. Both 1" (25.4 mm) and 1-3/4" (44.5 mm) insulating glass options are available for superior sound and enhanced thermal benefits. Thermal simulations show temperature variations from exterior/cold side to interior/warm side of GLASSvent™ UT Windows. Air Infiltration Water Structural – Uniform Wind Load Thermal Cycling Thermal Transmittance – U-Factor Condensation Resistance (CRF, I, CR) Overall Solar Heat Gain Coefficient (SHGC, VT) Sound Transmission (STC, OITC) ASTM E283 ASTM E331, E547 ASTM E330 AAMA 501.5 AAMA 1503, 507; NFRC 100 AAMA 1503; CSA A440.2; NFRC 500 AAMA 507; NFRC 200 ASTM E90, E1425; AAMA 1801 Fabrication and Installation GLASSvent™ UT Windows are available with the option to buy the window factory glazed by Kawneer or open for glazing by the window installer. The flexibility of GLASSvent™ UT Windows gives architects an ultra thermal option that combines high-performance vents with highperformance curtain walls and storefront systems, including the 1600UT System™ 1 Curtain Wall. Aesthetics and Design Options Double pane clear glass Double pane low-e argon glass Triple pane low-e argon glass The innovative, patent-pending design of GLASSvent™ UT Windows provides a sleek ventilation alternative for Kawneer curtain walls and storefront framing systems. Vents are available as project-out or outswing casement windows without the exterior aluminum profile sightlines experienced with typical operating vents. More than a streamlined appearance, GLASSvent™ UT Windows also deliver a convenient means for architects to ventilate with fresh air, which has been shown to improve indoor air quality, as well as improve occupant comfort, well-being and productivity. Attractive stainless steel four-bar hinges provide positive control for trouble-free operation. Durable cast white bronze locking hardware delivers strength and security, and integral frame-mounted insect screens ensure building occupant comfort. Exterior view of GLASSvent™ UT Window in curtain wall Closed position Kawneer Company, Inc. Technology Park / Atlanta 555 Guthridge Court Norcross, GA 30092 Open position kawneer.com 770 . 449 . 5555 © Kawneer Company, Inc. 2014 LITHO IN U.S.A. Form No. 14-2196 GLASSvent™ and 1600 UT System™ 1 are trademarks of Kawneer Company, Inc. and Alcoa Inc. Interior view of GLASSvent™ UT Window in curtain wall Closed position Open position JANUARY, 2016 GLASSventTM UT Windows EC 97911-087 INDEX PROJECT-OUT WINDOW (1" INFILL).............................................. 3-6 PROJECT-OUT WINDOW (1-3/4" INFILL)...................................... 7-10 OUTSWING CASEMENT WINDOW (1" INFILL).......................... 11-14 OUTSWING CASEMENT WINDOW (1-3/4" INFILL).................... 15-18 THERMAL CHARTS...................................................................... 19-31 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE, WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS, AND ASSUMES NO RESPONSIBILITY THEREFOR. Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses ( ) are millimeters unless otherwise noted. © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 1 The following metric (SI ) units are found in these details: m –meter cm – centimeter mm –millimeter s –second Pa –pascal MPa –megapascal Kawneer reserves the right to change configurations without prior notice when deemed necessary for product improvement. kawneer.com ADME077 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. GLASSventTM UT Windows BLANK PAGE ADME077 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 2 JANUARY, 2016 EC 97911-087 GLASSventTM UT Windows JANUARY, 2016 PROJECT-OUT WINDOW (1" INFILL) Features • Architectural Grade Window (AW) • Tested to US and Canadian Standards • 45° Mitered Vent and Frame Corners • Staked Corner Joinery • Architectural Anodized Finishes and Applied Coatings • Large Missile and Small Missile Hurricane Impact Tested • Blast Mitigation Tested Exterior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Interior Project-out Window (1" infill) For specific product applications, Consult your Kawneer representative. kawneer.com ADME077 3 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 Architectural Grade AW-PG90-AP TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) SYSTEM DEPTH 4-3/8" Overall System Depth TYPICAL WALL THICKNESS .125 Nominal Frame / .156" Nominal Vent TYPICAL MAX. VENT SIZE 60" x 36" TYPICAL MIN. VENT SIZE 17" x 17" INFILL OPTIONS 1" STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop OTHER OPTIONS Insect Screens Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. CLASS and GRADE ADME077 kawneer.com © Kawneer Company, Inc., 2014 PROJECT-OUT WINDOW (1" INFILL) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 4 © Kawneer Company, Inc., 2014 1-13/16" (46) 1/8" (3.2) kawneer.com 2-1/4" (57.2) D.L.O. ADME077 1-13/16" (46) 2-1/4" (57.2) 2 SILL D.L.O. D.L.O. 1-13/16" (46) 2-1/4" (57.2) W.D. C.W. D.L.O. 1/8" (3.2) 1 HEAD W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 1/8" (3.2) C.W. D.L.O. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2016 GLASSventTM UT Windows PROJECT-OUT WINDOW (1" INFILL) SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3 2 TYPICAL ELEVATION 4-3/8" (111.1) W.D. C.W. D.L.O. 3 JAMB NOTE:THE KAWNEER GLASSventTM UT WINDOW IS SHOWN IN THESE DETAILS WITH 1600UT SYSTEMTM1 CURTAIN WALL FOR REFERENCE. OTHER KAWNEER SYSTEMS CAN BE USED. FOR PRODUCT SPECIFIC APPLICATIONS CONSULT YOUR KAWNEER REPRESENTATIVE. 5 GLASSventTM UT Windows PROJECT-OUT WINDOW (1" INFILL) JANUARY, 2016 A standard hinge for ventilators providing approximately 45° to 60° openings depending on size. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are standard for the manual operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME077 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 6 GLASSventTM UT Windows JANUARY, 2016 PROJECT-OUT WINDOW (1-3/4" INFILL) Features • Architectural Grade Window (AW) • Tested to US and Canadian Standards • 45° Mitered Vent and Frame Corners • Staked Corner Joinery • Architectural Anodized Finishes and Applied Coatings • Large Missile and Small Missile Hurricane Impact Tested • Blast Mitigation Tested Exterior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Interior Project-out Window (1-3/4" infill) For specific product applications, Consult your Kawneer representative. kawneer.com ADME077 7 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 Architectural Grade AW-PG90-AP TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) SYSTEM DEPTH 5-1/8" Overall System Depth TYPICAL WALL THICKNESS .125 Nominal Frame / .156" Nominal Vent TYPICAL MAX. VENT SIZE 60" x 36" TYPICAL MIN. VENT SIZE 17" x 17" INFILL OPTIONS 1-3/4" STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop OTHER OPTIONS Insect Screens Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. CLASS and GRADE ADME077 kawneer.com © Kawneer Company, Inc., 2014 PROJECT-OUT WINDOW (1-3/4" INFILL) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 8 © Kawneer Company, Inc., 2014 1-13/16" (46) 1/8" (3.2) kawneer.com 2-1/4" (57.2) D.L.O. ADME077 1-13/16" (46) 2-1/4" (57.2) 2 SILL D.L.O. D.L.O. 1-13/16" (46) 2-1/4" (57.2) W.D. C.W. D.L.O. 1/8" (3.2) 1 HEAD W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 1/8" (3.2) C.W. D.L.O. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2016 GLASSventTM UT Windows PROJECT-OUT WINDOW (1-3/4" INFILL) SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3 2 TYPICAL ELEVATION 5-1/8" (130.2) W.D. C.W. D.L.O. 3 JAMB NOTE:THE KAWNEER GLASSventTM UT WINDOW IS SHOWN IN THESE DETAILS WITH 1600UT SYSTEMTM1 CURTAIN WALL FOR REFERENCE. OTHER KAWNEER SYSTEMS CAN BE USED. FOR PRODUCT SPECIFIC APPLICATIONS CONSULT YOUR KAWNEER REPRESENTATIVE. 9 GLASSventTM UT Windows PROJECT-OUT WINDOW (1-3/4" INFILL) JANUARY, 2016 A standard hinge for ventilators providing approximately 45° to 60° openings depending on size. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are standard for the manual operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME077 kawneer.com © Kawneer Company, Inc., 2014 STAINLESS STEEL 4 BAR HINGES Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 10 GLASSventTM UT Windows JANUARY, 2016 OUTSWING CASEMENT WINDOW (1" INFILL) Features • Architectural Grade Window (AW) • Tested to US and Canadian Standards • 45° Mitered Vent and Frame Corners • Staked Corner Joinery • Architectural Anodized Finishes and Applied Coatings • Large Missile and Small Missile Hurricane Impact Tested • Blast Mitigation Tested Outswing Casement Window (1" infill) HINGED LEFT Interior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Exterior For specific product applications, Consult your Kawneer representative. kawneer.com ADME077 11 OUTSWING CASEMENT WINDOW (1" INFILL) Architectural Grade AW-PG90-C TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) SYSTEM DEPTH 4-3/8" Overall System Depth TYPICAL WALL THICKNESS .125 Nominal Frame / .156" Nominal Vent TYPICAL MAX. VENT SIZE 36" x 60" TYPICAL MIN. VENT SIZE 17" x 24" INFILL OPTIONS 1" STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop OTHER OPTIONS Insect Screens EC 97911-087 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. CLASS and GRADE JANUARY, 2016 ADME077 kawneer.com © Kawneer Company, Inc., 2014 GLASSventTM UT Windows Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 12 © Kawneer Company, Inc., 2014 2-1/4" (57.2) 1/8" (3.2) kawneer.com 1-13/16" (46) D.L.O. ADME077 1-13/16" (46) 2-1/4" (57.2) 2 SILL D.L.O. D.L.O. 1-13/16" (46) 2-1/4" (57.2) 1/8" (3.2) 1 HEAD W.D. TYPICAL ELEVATION W.D. C.W. D.L.O. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 1/8" (3.2) C.W. D.L.O. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2016 GLASSventTM UT Windows OUTSWING CASEMENT WINDOW (1" INFILL) SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3 2 4-3/8" (111.1) W.D. C.W. D.L.O. 3 JAMB NOTE:THE KAWNEER GLASSventTM UT WINDOW IS SHOWN IN THESE DETAILS WITH 1600UT SYSTEMTM1 CURTAIN WALL FOR REFERENCE. OTHER KAWNEER SYSTEMS CAN BE USED. FOR PRODUCT SPECIFIC APPLICATIONS CONSULT YOUR KAWNEER REPRESENTATIVE. 13 JANUARY, 2016 EC 97911-087 STAINLESS STEEL 4 BAR HINGES A standard hinge for ventilators providing an opening of up to 45°. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are standard for the manual operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME077 kawneer.com © Kawneer Company, Inc., 2014 OUTSWING CASEMENT WINDOW (1" INFILL) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. GLASSventTM UT Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 14 GLASSventTM UT Windows JANUARY, 2016 OUTSWING CASEMENT WINDOW (1-3/4" INFILL) Features • Architectural Grade Window (AW) • Tested to US and Canadian Standards • 45° Mitered Vent and Frame Corners • Staked Corner Joinery • Architectural Anodized Finishes and Applied Coatings • Large Missile and Small Missile Hurricane Impact Tested • Blast Mitigation Tested Outswing Casement Window (1-3/4" infill) HINGED LEFT Interior © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 Exterior For specific product applications, Consult your Kawneer representative. kawneer.com ADME077 15 OUTSWING CASEMENT WINDOW (1-3/4" INFILL) Architectural Grade AW-PG90-C TESTING STANDARD AAMA / WDMA / CSA / 101 / I.S.2 / A440 (NAFS) SYSTEM DEPTH 5-1/8" Overall System Depth TYPICAL WALL THICKNESS .125 Nominal Frame / .156" Nominal Vent TYPICAL MAX. VENT SIZE 36" x 60" TYPICAL MIN. VENT SIZE 17" x 24" INFILL OPTIONS 1-3/4" STANDARD HARDWARE Stainless Steel 4-Bar Hinges Cast White Bronze Cam Handles OPTIONAL HARDWARE Access Control Locks Pole and Pole Ring Limit Stop OTHER OPTIONS Insect Screens EC 97911-087 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. CLASS and GRADE JANUARY, 2016 ADME077 kawneer.com © Kawneer Company, Inc., 2014 GLASSventTM UT Windows Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 16 © Kawneer Company, Inc., 2014 2-1/4" (57.2) 1/8" (3.2) kawneer.com 1-13/16" (46) D.L.O. ADME077 1-13/16" (46) 2-1/4" (57.2) 2 SILL D.L.O. D.L.O. 1-13/16" (46) 2-1/4" (57.2) 1/8" (3.2) 1 HEAD W.D. C.W. D.L.O. TYPICAL ELEVATION W.D. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. EC 97911-087 1/8" (3.2) C.W. D.L.O. Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. JANUARY, 2016 GLASSventTM UT Windows OUTSWING CASEMENT WINDOW (1-3/4" INFILL) SCALE : 3" = 1'-0" (Nominal Dimensions Shown) 1 3 2 5-1/8" (130.2) W.D. C.W. D.L.O. 3 JAMB NOTE:THE KAWNEER GLASSventTM UT WINDOW IS SHOWN IN THESE DETAILS WITH 1600UT SYSTEMTM1 CURTAIN WALL FOR REFERENCE. OTHER KAWNEER SYSTEMS CAN BE USED. FOR PRODUCT SPECIFIC APPLICATIONS CONSULT YOUR KAWNEER REPRESENTATIVE. 17 JANUARY, 2016 EC 97911-087 STAINLESS STEEL 4 BAR HINGES A standard hinge for ventilators providing an opening of up to 45°. An optional limit stop is available to restrict hinge travel and limit vent opening. CAM HANDLE Cast white bronze cam handles are standard for the manual operation and locking of ventilators. CAM HANDLE WITH POLE RING Cast white bronze cam handles with pole ring provide manual operation of ventilators located above reach. These handles are operated with a sash pole. POLE RING Cast white bronze pole ring is used in conjunction with locking hardware for sash pole operation of ventilators. SASH POLE A 3/4" diameter aluminum sash pole with a cast white bronze pull down hook and black rubber tip. Available in 6 ft. and 12 ft. lengths with optional cast white bronze Pole Hanger. HANGER FOR SASH POLE ACCESS CONTROL LOCK In lieu of cam handles cast white bronze access control locks are offered for managed control of vent operations. Lock is operated with a manganese bronze removable handle. ADME077 kawneer.com © Kawneer Company, Inc., 2014 OUTSWING CASEMENT WINDOW (1-3/4" INFILL) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. GLASSventTM UT Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 18 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL CHARTS Generic Project Specific U-factor Example Calculation (Percent of Glass will vary on specific products depending on sitelines) 55-1/2" (1410) 5'-0" (1524) Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. 3'-0" (915) 31-1/2" (800) Example Glass U-Factor = 0.28 Btu/hr • ft2 • °F Total Daylight Opening = 31-1/2" • 55-1/2" = 12.14ft2 Total Projected Area = 3' 0" • 5' 0" = 15 ft2 Percent of Glass = (Total Daylight Opening ÷ Total Projected Area)100 = (12.14 ÷ 15)100 = 81% COG U-factor 0.48 (2.74) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) © Kawneer Company, Inc., 2014 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) T 0.40 (2.27) E IGN PL S M E A D EX FOR 0.42 (2.39) O 0.44 (2.50) 0.38 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) Percent of Glass Area 81% 0.10 (0.57) Based on 81% glass and center of glass (COG) U-factor of 0.28 System U-factor is equal to 0.38 Btu/hr • ft2 • °F kawneer.com ADME077 Btu hr • ft2 • °F System U-factor 0.46 (2.61) N Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System U-factor vs Percent of Glass Area 19 20 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.74) 0.46 (2.61) 0.44 (2.50) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME077 kawneer.com © Kawneer Company, Inc., 2014 0.40 (2.27) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Btu hr • ft2 • °F System U-factor 0.42 (2.39) System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2016 kawneer.com GLASSventTM UT Windows Vision Area / Total Area (%) ADME077 21 EC 97911-087 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT GLASSventTM UT Windows 22 JANUARY, 2016 THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-087 Thermal Transmittance 1 (BTU/hr • ft 2 • °F) 0.48 0.57 0.55 0.46 0.56 0.53 0.44 0.54 0.52 0.42 0.53 0.50 0.40 0.52 0.49 0.38 0.50 0.47 0.36 0.49 0.46 0.34 0.47 0.44 0.32 0.46 0.43 0.30 0.44 0.41 0.28 0.43 0.40 0.26 0.41 0.38 0.24 0.40 0.37 0.22 0.38 0.35 0.20 0.37 0.34 0.18 0.35 0.32 0.16 0.33 0.31 0.14 0.32 0.29 0.12 0.30 0.28 0.10 0.29 0.26 PROJECT-OUT WINDOW WITH 1" GLAZING NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 Glass SHGC Visible Transmittance 2 Overall SHGC 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.59 0.58 0.70 0.55 0.65 Glass VT Overall VT 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.56 0.56 0.55 0.70 0.52 0.52 0.51 0.51 0.65 0.48 0.48 0.60 0.47 0.47 0.60 0.45 0.45 0.55 0.44 0.43 0.55 0.41 0.41 0.50 0.40 0.40 0.50 0.37 0.37 0.45 0.36 0.36 0.45 0.33 0.33 0.40 0.33 0.32 0.40 0.30 0.30 0.35 0.29 0.28 0.35 0.26 0.26 0.30 0.25 0.25 0.30 0.22 0.22 0.25 0.21 0.21 0.25 0.19 0.19 0.20 0.18 0.17 0.20 0.15 0.15 0.15 0.14 0.14 0.15 0.11 0.11 0.10 0.10 0.10 0.10 0.07 0.07 0.05 0.06 0.06 0.05 0.04 0.04 ADME077 kawneer.com © Kawneer Company, Inc., 2014 Warm Edge Spacer Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Aluminum Spacer Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass U-Factor Overall U-Factor 4 3 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL CHARTS PROJECT-OUT WINDOW WITH 1-3/4" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor Btu hr • ft2 • °F System U-factor 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.22 (1.25) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME077 23 System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME077 kawneer.com © Kawneer Company, Inc., 2014 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC GLASSventTM UT Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 24 JANUARY, 2016 EC 97911-087 PROJECT-OUT WINDOW WITH 1-3/4" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL PERFORMANCE MATRIX (NFRC SIZE) Glass U-Factor PROJECT-OUT WINDOW WITH 1-3/4" GLAZING Overall U-Factor 4 3 Aluminum Spacer Warm Edge Spacer 0.30 0.42 0.39 0.28 0.41 0.38 0.26 0.39 0.36 0.24 0.38 0.35 0.22 0.36 0.33 0.20 0.35 0.31 0.18 0.34 0.30 0.16 0.32 0.29 0.14 0.31 0.27 0.12 0.29 0.26 0.10 0.28 0.24 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Glass SHGC kawneer.com 25 Visible Transmittance 2 Overall SHGC 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.58 0.58 0.70 0.55 0.65 Glass VT Overall VT 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.56 0.56 0.54 0.70 0.52 0.52 0.51 0.51 0.65 0.48 0.48 0.60 0.47 0.47 0.60 0.45 0.45 0.55 0.44 0.43 0.55 0.41 0.41 0.50 0.40 0.39 0.50 0.37 0.37 0.45 0.36 0.36 0.45 0.33 0.33 0.40 0.32 0.32 0.40 0.30 0.30 0.35 0.29 0.28 0.35 0.26 0.26 0.30 0.25 0.24 0.30 0.22 0.22 0.25 0.21 0.21 0.25 0.19 0.19 0.20 0.17 0.17 0.20 0.15 0.15 0.15 0.14 0.13 0.15 0.11 0.11 0.10 0.10 0.10 0.10 0.07 0.07 0.05 0.06 0.06 0.05 0.04 0.04 ADME077 26 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL CHARTS OUTSWING CASEMENT WINDOW WITH 1" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor 0.48 (2.74) 0.46 (2.61) 0.44 (2.50) 0.42 (2.39) 0.38 (2.16) 0.36 (2.05) 0.34 (1.93) 0.32 (1.82) Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.22 (1.25) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.79) 0.12 (0.68) 0.10 (0.57) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. ADME077 kawneer.com © Kawneer Company, Inc., 2014 Btu hr • ft2 • °F System U-factor 0.40 (2.27) System VT © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System SHGC Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. JANUARY, 2016 kawneer.com GLASSventTM UT Windows EC 97911-087 Vision Area / Total Area (%) ADME077 27 THERMAL CHARTS OUTSWING CASEMENT WINDOW WITH 1" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) System Visible Transmittance (VT) vs Percent of Vision Area COG VT GLASSventTM UT Windows 28 JANUARY, 2016 THERMAL PERFORMANCE MATRIX (NFRC SIZE) EC 97911-087 Thermal Transmittance 1 (BTU/hr • ft 2 • °F) 0.48 0.55 0.52 0.46 0.54 0.51 0.44 0.53 0.49 0.42 0.51 0.48 0.40 0.50 0.46 0.38 0.48 0.45 0.36 0.47 0.44 0.34 0.45 0.42 0.32 0.44 0.41 0.30 0.43 0.39 0.28 0.41 0.38 0.26 0.40 0.36 0.24 0.38 0.35 0.22 0.37 0.33 0.20 0.36 0.32 0.18 0.33 0.30 0.16 0.32 0.29 0.14 0.30 0.27 0.12 0.29 0.26 0.10 0.27 0.24 OUTSWING CASEMENT WINDOW WITH 1" GLAZING NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 Glass SHGC Visible Transmittance 2 Overall SHGC 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.58 0.58 0.70 0.55 0.65 Glass VT Overall VT 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.56 0.56 0.54 0.70 0.52 0.52 0.51 0.51 0.65 0.48 0.48 0.60 0.47 0.47 0.60 0.45 0.45 0.55 0.43 0.43 0.55 0.41 0.41 0.50 0.40 0.39 0.50 0.37 0.37 0.45 0.36 0.36 0.45 0.33 0.33 0.40 0.32 0.32 0.40 0.30 0.30 0.35 0.29 0.29 0.35 0.26 0.26 0.30 0.25 0.25 0.30 0.22 0.22 0.25 0.21 0.21 0.25 0.19 0.19 0.20 0.17 0.17 0.20 0.15 0.15 0.15 0.14 0.13 0.15 0.11 0.11 0.10 0.10 0.10 0.10 0.07 0.07 0.05 0.06 0.06 0.05 0.04 0.04 ADME077 kawneer.com © Kawneer Company, Inc., 2014 Warm Edge Spacer Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Aluminum Spacer Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Glass U-Factor Overall U-Factor 4 3 GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL CHARTS OUTSWING CASEMENT WINDOW WITH 1-3/4" GLAZING Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Note: Values in parentheses are metric. COG = Center of Glass. Charts are generated per AMMA 507 System U-factor vs Percent of Glass Area COG U-factor Btu hr • ft2 • °F System U-factor 0.30 (1.71) 0.28 (1.59) 0.26 (1.48) 0.24 (1.37) 0.20 (1.14) 0.18 (1.02) 0.16 (0.91) 0.14 (0.80) 0.12 (0.68) 0.10 (0.57) © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 0.22 (1.25) Percent of Glass Area = Vision Area/Total Area Daylight Opening / Projected Area Notes for System U-factor, SHGC and VT charts: For glass values that are not listed, linear interpolation is permitted. Glass properties are based on center of glass values and are obtained from your glass supplier. kawneer.com ADME077 29 System Visible Transmittance (VT) vs Percent of Vision Area COG VT Vision Area / Total Area (%) ADME077 kawneer.com © Kawneer Company, Inc., 2014 THERMAL CHARTS Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. System SHGC GLASSventTM UT Windows Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. System VT 30 JANUARY, 2016 EC 97911-087 OUTSWING CASEMENT WINDOW WITH 1-3/4" GLAZING System Solar Heat Gain Coefficient (SHGC) vs Percent of Vision Area COG SHGC Vision Area / Total Area (%) GLASSventTM UT Windows JANUARY, 2016 EC 97911-087 THERMAL PERFORMANCE MATRIX (NFRC SIZE) OUTSWING CASEMENT WINDOW WITH 1-3/4" GLAZING Overall U-Factor 4 Glass U-Factor 3 Aluminum Spacer Warm Edge Spacer 0.30 0.40 0.37 0.28 0.39 0.35 0.26 0.38 0.34 0.24 0.36 0.32 0.22 0.35 0.31 0.20 0.33 0.29 0.18 0.32 0.28 0.16 0.30 0.26 0.14 0.29 0.25 0.12 0.27 0.23 0.10 0.26 0.22 NOTE:For glass values that are not listed, linear interpolation is permitted. 1. 2. 3. 4. U-Factors are determined in accordance with NFRC 100. SHGC and VT values are determined in accordance with NFRC 200. Glass properties are based on center of glass values and are obtained from your glass supplier. Overall U-Factor, SHGC, and VT Matricies are based on the standard NFRC specimen size of 1500mm wide by 600mm high (59-1/16" by 23-5/8"). SHGC Matrix 2 © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. Thermal Transmittance 1 (BTU/hr • ft 2 • °F) Glass SHGC kawneer.com 31 Visible Transmittance 2 Overall SHGC 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.58 0.58 0.70 0.54 0.65 Glass VT Overall VT 4 3 Aluminum Spacer Warm Edge Spacer 0.75 0.56 0.56 0.54 0.70 0.52 0.52 0.51 0.50 0.65 0.48 0.48 0.60 0.47 0.47 0.60 0.45 0.45 0.55 0.43 0.43 0.55 0.41 0.41 0.50 0.40 0.39 0.50 0.37 0.37 0.45 0.36 0.35 0.45 0.33 0.33 0.40 0.32 0.32 0.40 0.30 0.30 0.35 0.28 0.28 0.35 0.26 0.26 0.30 0.25 0.24 0.30 0.22 0.22 0.25 0.21 0.20 0.25 0.19 0.19 0.20 0.17 0.17 0.20 0.15 0.15 0.15 0.14 0.13 0.15 0.11 0.11 0.10 0.10 0.09 0.10 0.07 0.07 0.05 0.06 0.06 0.05 0.04 0.04 ADME077 Laws and building and safety codes governing the design and use of glazed entrance, window, and curtain wall products vary widely. Kawneer does not control the selection of product configurations, operating hardware, or glazing materials, and assumes no responsibility therefor. GLASSventTM UT Windows BLANK PAGE ADME077 kawneer.com © Kawneer Company, Inc., 2014 Kawneer reserves the right to change configuration without prior notice when deemed necessary for product improvement. 32 JANUARY, 2016 EC 97911-087