Absolute encoders - SSI Solid shaft ø10 mm with clamping flange Magnetic multiturn encoders 12 bit ST / 13 bit MT BMMV 58 SSI - MAGRES hermetic Features –– Encoder multiturn / SSI –– Magnetic sensing, hermetically sealed –– Resolution: singleturn 12 bit, multiturn 13 bit –– High resistance to shock and vibrations –– Reset input –– Protection IP 69K –– Material: stainless steel 1.4305 Technical data - mechanical design Voltage supply Size (flange) ø58 mm Shaft type ø10 mm solid shaft (clamping flange) Flange Clamping flange Protection DIN EN 60529 IP 68, IP 69K Operating speed ≤6000 rpm Operating torque typ. 0.031 Nm Admitted shaft load ≤120 N axial (combined) ≤280 N radial (combined) ≤270 N axial (concentrated load) Materials Stainless steel 1.4305 (other materials on request) Operating temperature -40...+85 °C Resistance DIN EN 60068-2-6 Vibration 30 g, 10-2000 Hz DIN EN 60068-2-27 Shock 500 g, 6 ms Weight approx. 690 g Connection Connector M12, 8-pin Cable 5 VDC ±10 % 10...30 VDC Consumption typ. 100 mA (5 VDC, w/o load) 50 mA (24 VDC, w/o load) Initializing time typ. 170 ms after power on Interface SSI Function Multiturn Steps per turn 4096 / 12 bit Number of turns 8192 / 13 bit Absolute accuracy ±1 ° Sensing method Magnetic Code Gray or binary Code sequence CW: ascending values with clockwise sense of rotation; looking at flange Inputs SSI clock Zero setting input Output stages SSI data: linedriver RS485 Interference immunity DIN EN 61000-6-2 Emitted interference DIN EN 61000-6-3 Approval UL approval / E217823 1 www.baumer.com/motion 13/8/2015 Technical data - electrical ratings Subject to modification in technic and design. Errors and omissions excepted. BMMV 58K SSI with clamping flange Absolute encoders - SSI Solid shaft ø10 mm with clamping flange Magnetic multiturn encoders 12 bit ST / 13 bit MT BMMV 58 SSI - MAGRES hermetic Part number Accessories Multiturn clamping flange Connectors and cables BMMV 58K5 12/13 10146775 H0 Female connector M12, 8-pin, straight, without cable Mounting accessories Connection 5 Cable radial N Connector M12, 5-pin, radial 10252773 Clamp set ø15 mm 11053277 Bellows coupling aluminium/stainless steel 10 mm Solid shaft H0 ø10 mm, IP 68 and IP 69K Resolution 12/13 12/13 bit single-/multiturn Voltage supply / signals 05C 5 VDC / SSI 24C 10...30 VDC / SSI Code N Binary code G Gray code Data transfer T=1/f tm clock bit n bit n-1 bit 3 bit 2 bit 1 Clock frequency f 100...1000 kHz Duty cycle of T 40...60 % Delay time tv 200 ns Monoflop time tm 20 µs + T/2 Subject to modification in technic and design. Errors and omissions excepted. tv Trigger level Control inputs Input circuit Input level Low <0,4 V (>2 ms) Input level High +Vs or open 2 www.baumer.com/motion 13/8/2015 data Absolute encoders - SSI Solid shaft ø10 mm with clamping flange Magnetic multiturn encoders 12 bit ST / 13 bit MT BMMV 58 SSI - MAGRES hermetic Terminal significance Terminal assignment +Vs 0V Encoder ground connection relating to +Vs. Cable for connection reference -5 Data+ Positive, serial data output of differential linedriver. Core colour Signals Description brown +Vs Supply voltage Data- Negative, serial data output of differential linedriver. white 0V Supply voltage Clock+ Positive SSI clock input. Clock+ together with Clock- forms a current loop. A current of approx. 7 mA towards Clock+ input means logic 1 in positive logic. grey Data+ Data signal pink Data- Data signal green Clock+ Clock signal yellow Clock- Clock signal blue Zero Zero setting input red d.u. do not use Screen connected to housing Rot. direction Cable data Input for setting a zero point anywhere within the encoder resolution. The zero setting operation is triggered by a Low impulse. Connect to +Vs after setting operation for maximum interference immunity. Impulse duration >2 ms. 8 x 0,14 mm2 Connector M12 male for connection reference -N Connector Ascending position values when looking at the flange and rotating the shaft clockwise. Signals Description Pin 1 0V Supply voltage Pin 2 +Vs Supply voltage Pin 3 Clock+ Clock signal Pin 4 Clock- Clock signal Pin 5 Data+ Data signal Pin 6 Data- Data signal Pin 7 Zero Zero setting input Pin 8 d.u. do not use 5 6 1 3 4 3 8 7 Subject to modification in technic and design. Errors and omissions excepted. Zero Negative SSI clock input. Clock- together with Clock+ forms a current loop. A current of approx. 7 mA towards Clock- input means logic 0 in positive logic. 2 www.baumer.com/motion 13/8/2015 Clock- Encoder supply voltage. Absolute encoders - SSI Solid shaft ø10 mm with clamping flange Magnetic multiturn encoders 12 bit ST / 13 bit MT BMMV 58 SSI - MAGRES hermetic Dimensions ø 12 20 10 0,5 3 3 3 3 30 36 h8 25 30 M3 x 7 3 x 120° 9 ø 10 f6 M3 x 7 3 x 120° ø 60 ø 10 f6 20 10 0,5 9 ø 12 BMMV 58 SSI, connector M12 radial ø 60 BMMV 58 SSI, cable radial 36 h8 48 ±0,1 58 48 ±0,1 58 52 25 52 BMMV 58 SSI, cable radial, Ex ¡ 0[ [ K Subject to modification in technic and design. Errors and omissions excepted. 4 www.baumer.com/motion 13/8/2015 ¡ ¡ I